Ammonium Fluoride Passivation of CdZnTeSe Sensors for Applications in Nuclear Detection and Medical Imaging.

Cadmium zinc telluride selenide (Cd1-xZnxTe1-ySey or CZTS) is one of the emerging CdTe-based semiconductor materials for detecting X- and gamma-ray radiation at or near room temperature (i.e., without cryogenic cooling). Potential applications of CZTS sensors include medical imaging, X-ray detection, and gamma-ray spectroscopy. Chemical passivation of CZTS is needed to reduce the conductivity of Te-rich surfaces, which reduces the noise and improves the device performance. In this study, we focus on the effect of surface passivation of CZTS using a 10% aqueous solution of ammonium fluoride. The effects of the chemical treatment were studied on the leakage current, charge transport measured as the electron mobility-lifetime (µτ) product, and the spectral resolution measured as the full-width at half-maximum (FWHM) of specific peaks. After passivation, the leakage current increased and began to decrease towards pre-passivation levels. The energy resolutions were recorded for eight applied voltages between -35 V and -200 V. The results showed an average of 25% improvement in the detector's energy resolution for the 59.6 keV gamma peak of Am-241. The electron µτ product was unchanged at 2 × 10-3 cm2/V. These results show that ammonium fluoride is effective for chemical passivation of CZTS detectors.

Highly sensitive electrochemical biosensor for streptavidin detection based on CdSe quantum dots.

An electrochemical biosensor was developed based on a steric hindrance hybridization assay to allow the highly sensitive detection of streptavidin. In the steric hindrance hybridization assay, the signaling strand DNA (sig-DNA) was labeled at the 3' end with CdSe quantum dots (QDs) and at the 5' end with biotin, and capturing strand DNA (the complementary strand of sig-DNA) was labeled at the 5' end with thiol. The steric hindrance effect generated by streptavidin which was bound with the signaling DNA strand. The streptavidin limited the ability of the sig-DNA to hybridize with the cap-DNA, which were linked on the surface of a gold electrode. Therefore, the concentration of streptavidin was detected indirectly based on the concentration of CdSe QDs on the electrode surface. The concentration of CdSe QDs on the electrode surface was detected by differential pulse anodic stripping voltammetry. Under optimal conditions, the streptavidin detection range using the as-prepared biosensor was 1.96pg/mL to 1.96µg/mL and the detection limit was 0.65pg/mL. The experimental results showed that the electrochemical biosensor could detect streptavidin rapidly and accurately.

Visible photoelectrochemical sensing platform by in situ generated CdS quantum dots decorated branched-TiO2 nanorods equipped with Prussian blue electrochromic display.

In this study, based on in situ generation of CdS quantum dots (QDs) on the surface of branched TiO2 (B-TiO2) nanorods, an solar innovative photoelectrochemical (PEC) sensing platform was constructed for real-time, and sensitive detection of cellular H2S. Specifically, B-TiO2 nanorods arrays consisting of TiO2 nanorods directly grown on fluorine-doped tin oxide (FTO) further using TiCl3 mediated surface treatment of TiO2 nanorods are designed and fabricated as a new type of photoelectrode. CdS quantum dots (QDs) was formed on the surface of B-TiO2 nanorods arrays through the reaction between Cd2+ and S2-. And a significant enhancement in the photocurrent was obtained that ascribed to the formation of CdS-B-TiO2 heterostructures, thus leading to sensitive PEC recording of the H2S level in buffer and cellular environments. By using Prussian blue (PB) a electrochromic material to capture the photoelectron generated from the photoelectrode, a new visual system was proposed due to the formation of Prussian white (PW), which could be used to visualize the quantum photoelectric effect. This novel PEC sensing platform not only achieved satisfied analysis results toward S2-, but also showed excellent sensitivity, selectivity, low cost, and portable features. The strategy through the in situ generation of semiconductor nanoparticles on the surface of wide band-gap semiconductor paves the way for the improvements of PEC analytical performance. Meanwhile, the quantitative read-out electrochromic display paves a facile avenue and initiates new opportunities for creation of cheap, miniaturization sensors for other relevant analytes.

[Development of ICP-OES, ICP-MS and GF-AAS Methods for Simultaneous Quantification of Lead, Total Arsenic and Cadmium in Soft Drinks].

In this study, we developed methods to quantify lead, total arsenic and cadmium contained in various kinds of soft drinks, and we evaluated their performance. The samples were digested by common methods to prepare solutions for measurement by ICP-OES, ICP-MS and graphite furnace atomic absorption spectrometry (GF-AAS). After digestion, internal standard was added to the digestion solutions for measurements by ICP-OES and ICP-MS. For measurement by GF-AAS, additional purification of the digestion solution was conducted by back-extraction of the three metals into nitric acid solution after extraction into an organic solvent with ammonium pyrrolidine dithiocarbamate. Performance of the developed methods were evaluated for eight kinds of soft drinks.

An endophytic bacterium Acinetobacter calcoaceticus Sasm3-enhanced phytoremediation of nitrate-cadmium compound polluted soil by intercropping Sedum alfredii with oilseed rape.

Intensive agricultural system with high input of fertilizer results in high agricultural output. However, excessive fertilization in intensive agricultural system has great potential to cause nitrate and heavy metal accumulation in soil, which is adverse to human health. The main objective of the present study was to observe the effects of intercropping and inoculation of endophytic bacterium Acinetobacter calcoaceticus Sasm3 on phytoremediation of combined contaminated soil in oilseed rape (Brassica napus L.). The results showed that with Sasm3 inoculation, the biomass of rape was increased by 10-20% for shoot, 64% for root, and 23-29% for seeds while the nitrate accumulation in rape was decreased by 14% in root and by 12% in shoot. The cadmium concentration in rape increased significantly with mono-inoculating treatment, whereas it decreased significantly after intercropping treatment. By denaturing gradient gel electrophoresis (DGGE) and real-time quantitative PCR analysis, the diversity of bacterial community and the number of nirS and nirK gene copies increased significantly with inoculation or/and intercropping treatment. In conclusion, the endophytic bacterium Sasm3-inoculated intercropping system not only improved the efficiency of clearing cadmium from soil without obstructing crop production, but also improved the quality of crop.

In situ detection of salicylic acid binding sites in plant tissues.

The determination of hormone-binding sites in plants is essential in understanding the mechanisms behind hormone function. Salicylic acid (SA) is an important plant hormone that regulates responses to biotic and abiotic stresses. In order to label SA-binding sites in plant tissues, a quantum dots (QDs) probe functionalized with a SA moiety was successfully synthesized by coupling CdSe QDs capped with 3-mercaptopropionic acid (MPA) to 4-amino-2-hydroxybenzoic acid (PAS), using 1-ethyl-3-(3-dimethyllaminopropyl) carbodiimide (EDC) as the coupling agent. The probe was then characterized by dynamic light scattering and transmission electron microscopy, as well as UV/vis and fluorescence spectrophotometry. The results confirmed the successful conjugation of PAS to CdSe QDs and revealed that the conjugates maintained the properties of the original QDs, with small core diameters and adequate dispersal in solution. The PAS-CdSe QDs were used to detect SA-binding sites in mung bean and Arabidopsis thaliana seedlings in vitro and in vivo. The PAS-CdSe QDs were effectively transported into plant tissues and specifically bound to SA receptors in vivo. In addition, the effects of the PAS-CdSe QDs on cytosolic Ca(2+) levels in the tips of A. thaliana seedlings were investigated. Both SA and PAS-CdSe QDs had similar effects on the trend in cytosolic-free Ca(2+) concentrations, suggesting that the PAS-CdSe QDs maintained the bioactivity of SA. To summarize, PAS-CdSe QDs have high potential as a fluorescent probe for the in vitro/in vivo labeling and imaging of SA receptors in plants.

Removal of CdTe in acidic media by magnetic ion-exchange resin: a potential recycling methodology for cadmium telluride photovoltaic waste.

Sulfonated magnetic microspheres (PSt-DVB-SNa MPs) have been successfully prepared as adsorbents via an aqueous suspension polymerization of styrene-divinylbenzene and a sulfonation reaction successively. The resulting adsorbents were confirmed by means of Fourier transform infrared spectra (FT-IR), X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope equipped with an energy dispersive spectrometer (SEM-EDS) and vibrating sample magnetometer (VSM). The leaching process of CdTe was optimized, and the removal efficiency of Cd and Te from the leaching solution was investigated. The adsorbents could directly remove all cations of Cd and Te from a highly acidic leaching solution of CdTe. The adsorption process for Cd and Te reached equilibrium in a few minutes and this process highly depended on the dosage of adsorbents and the affinity of sulfonate groups with cations. Because of its good adsorption capacity in strong acidic media, high adsorbing rate, and efficient magnetic separation from the solution, PSt-DVB-SNa MPs is expected to be an ideal material for the recycling of CdTe photovoltaic waste.

Biosynthesis of CdS nanoparticles in banana peel extract.

Cadmium sulfide (CdS) nanoparticles (NPs) were synthesized by using banana peel extract as a convenient, non-toxic, eco-friendly 'green' capping agent. Cadmium nitrate and sodium sulfide are main reagents. A variety of CdS NPs are prepared through changing reaction conditions (banana extracts, the amount of banana peel extract, solution pH, concentration and reactive temperature). The prepared CdS colloid displays strong fluorescence spectrum. X-ray diffraction analysis demonstrates the successful formation of CdS NPs. Fourier transform infra-red (FTIR) spectrogram indicates the involvement of carboxyl, amine and hydroxyl groups in the formation of CdS NPs. Transmission electron microscope (TEM) result reveals that the average size of the NPs is around 1.48 nm.

Structural characterization of Cd²âº complexes in solution with DMSA and DMPS.

Meso-2,3-dimercaptosuccinic acid (DMSA) and 2,3-dimercaptopropane-1-sulfonic acid (DMPS) are chelating agents which have been used clinically to treat patients suffering from Pb(2+) or Hg(2+) exposure. Cd(2+) is a related environmental pollutant that is of increasing public health concern due to a demonstrated dose-response between urinary Cd level and an increased risk of diabetes. However, therapeutically effective chelating agents which enhance the excretion of Cd(2+) from humans have yet to be identified. Here we present a structural characterization of complexes of DMSA and DMPS with Cd(2+) at physiological pH using a combination of X-ray absorption spectroscopy, size exclusion chromatography and density functional theory. The results indicate a complex chemistry in which multi-metallic forms are important, but are consistent with both DMPS and DMSA acting as true chelators, using two thiolates for DMPS and one thiolate and one carboxylate for DMSA.

Automatically purification of aqueous CdTe nanocrystals in water-ethanol co-environment.

Purification is a separated post-treatment step after the synthesis of nanocrystals (NCs) in order to exclude excess ligands and monomers in NC solution. The common purification process involves many manipulations, such as concentrating, addition of anti-solvents and centrifugation, which are troublesome and time consuming. In this work, we originally integrate NC synthesis and NC purification in one-pot via selecting water-ethanol co-environment for NC synthesis and NC purification. Our research shows that NCs can grow in water-ethanol mixture. When growing into critical size, NCs will automatically precipitate from the solution. Element analysis demonstrates that precipitates fraction fits well with stoichiometric of ligand-capped NCs. Excess monomers are left in supernatant, and thus achieving automatically purification of NCs in the water-ethanol co-environment. By adjusting the volume ratios of water and ethanol in bi-solvent system, different-sized purified NCs can be controlled. Besides, this water-ethanol co-environment can be used in both thermal-promoted and hydrazine-promoted growth.

Cadmium phytoextraction potential of different Alyssum species.

This work was planned for providing useful information about the possibility of using serpentine adapted plants for phytoextraction of cadmium, element scarcely represented in such metalliferous environment. To this aim, we investigated variation in cadmium tolerance, accumulation and translocation in three Alyssum plants with different phenotypes: Alyssum bertolonii, that is a serpentine endemic nickel hyperaccumulator, and two populations of Alyssum montanum, one adapted and one not adapted to serpentine soils. Plants were hydroponically cultivated in presence of increasing concentrations of CdSO(4) for two weeks. For the metal concentration used in the experiments, the three different Alyssum populations showed variation in cadmium tolerance, accumulation and content. The serpentine adapted population of A. montanum showed statistically higher cadmium tolerance and accumulation than A. bertolonii and the population of A. montanum not adapted to serpentine soil thus deserving to be investigated for phytoextraction purposes. Furthermore, as for the kinetic parameters of the cadmium uptake system, A. montanum serpentine population presented a low apparent K(m) value, suggesting a high affinity for this metal of its uptake system, whereas the V(max) values were not significantly different among the plants. Present data revealed metallicolous plants are also suitable for the phytoremediation of metals underrepresented in the environment of their initial origin. Nonetheless, field trials on real contaminated soils are essential.

Layer-by-layer assembled Fe3O4@C@CdTe core/shell microspheres as separable luminescent probe for sensitive sensing of Cu2+ ions.

A novel multifunctional microsphere with a fluorescent CdTe quantum dots (QDs) shell and a magnetic core (Fe(3)O(4)) has been successfully developed and prepared by a combination of the hydrothermal method and layer-by-layer (LBL) self-assembly technique. The resulting fluorescent Fe(3)O(4)@C@CdTe core/shell microspheres are utilized as a chemosensor for ultrasensitive Cu(2+) ion detection. The fluorescence of the obtained chemosensor could be quenched effectively by Cu(2+) ions. The quenching mechanism was studied and the results showed the existence of both static and dynamic quenching processes. However, static quenching is the more prominent of the two. The modified Stern-Volmer equation showed a good linear response (R(2) = 0.9957) in the range 1-10 µM with a quenching constant (K(sv)) of 4.9 × 10(4) M(-1). Most importantly, magnetic measurements showed that the Fe(3)O(4)@C@CdTe core/shell microspheres were superparamagnetic and they could be separated and collected easily using a commercial magnet in 10 s. These results obtained not only provide a way to solve the embarrassments in practical sensing applications of QDs, but also enable the fabrication of other multifunctional nanostructure-based hybrid nanomaterials.

Removal of Cd(II) from aqueous solution with activated Firmiana Simplex Leaf: behaviors and affecting factors.

Cadmium pollution is known to cause severe public health problems. This study is intended to examine the effect of an activated Firmiana Simplex Leaf (FSL) on the removal of Cd(II) from aqueous solution. Results showed that the active Firmiana Simplex Leaf could efficiently remove Cd(II) from wastewater due to the preservation of beneficial groups (amine, carboxyl, and phosphate) at a temperature of 250 degrees C. The adsorbent component, dosage, concentration of the initial solute, and the pH of the solution were all found to have significant effects on Cd(II) adsorption. The kinetic constants were predicted by pseudo-first-order kinetics, and the thermodynamic analysis revealed the endothermic and spontaneous nature of the adsorption. FT-IR and XRD analyses confirmed the strong adsorption between beneficial groups and cadmium ions, and the adsorption capacity was calculated to be 117.786 mg g(-1) according to the Langmuir isotherm.

Chemical control of the photoluminescence of CdSe quantum dot-organic complexes with a series of para-substituted aniline ligands.

Replacement of the native (as-synthesized) ligands of colloidal CdSe QDs with varying concentrations of a series of para-substituted anilines (R-An), where R ranges from strongly electron-withdrawing to strongly electron-donating, decreases the PL of the QDs. The molar ratio of R-An to QD ([R-An]:[QD]) at which the PL decreases by 50% shifts by 4 orders of magnitude over the series R-An. The model employed to describe the data combines a Freundlich binding isotherm (which reflects the dependence of the binding affinity of the amine headgroups of R-An on the substituent R) with a function that describes the response of the PL to R-An ligands once they are bound at their equilibrium surface coverage. The latter function includes as a parameter the rate constant, k(nr), for nonradiative decay of the exciton at a site to which an R-An ligand is coordinated. The value of this parameter reveals that the predominant mechanism of QD-ligand interaction is passivation of Cd(2+) surface sites through sigma-donation for R-An ligands with R = H, Br, OCF(3), and reductive quenching through photoinduced hole transfer for R = MeO, (Me)(2)N.

Tris(2-aminoethyl) amine functionalized silica gel for solid-phase extraction and preconcentration of Cr(III), Cd(II) and Pb(II) from waters.

A new tris(2-aminoethyl) amine (TREN) functionalized silica gel (SG-TREN) was prepared and investigated for selective solid-phase extraction (SPE) of trace Cr(III), Cd(II) and Pb(II) prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). Identification of the surface modification was characterized and performed on the basis of FT-IR. The separation/preconcentration conditions of analytes were investigated, including effects of pH, the shaking time, the sample flow rate and volume, the elution condition and the interfering ions. At pH 4, the maximum adsorption capacity of Cr(III), Cd(II) and Pb(II) onto the SG-TREN were 32.72, 36.42 and 64.61 mg g(-1), respectively. The adsorbed metal ions were quantitatively eluted by 5 mL of 0.1 mol L(-1) HCl. Common coexisting ions did not interfere with the separation. According to the definition of International Union of Pure and Applied Chemistry, the detection limits (3sigma) of this method for Cr(III), Cd(II) and Pb(II) were 0.61, 0.14 and 0.55 ng mL(-1), respectively. The relative standard deviation under optimum conditions is less than 4.0% (n=11). The application of this modified silica gel to preconcentration trace Cr(III), Cd(II) and Pb(II) of two water samples gave high accurate and precise results.

Purification of denatured bovine serum albumin coated CdTe quantum dots for sensitive detection of silver(I) ions.

CdTe quantum dots (QDs) were synthesized in aqueous solution with 3-mercaptopropionic acid as the stabilizer. Chemically reduced bovine serum albumin (BSA) was used to modify the surface of the QDs. Experimental results showed that the denatured BSA (dBSA) could be effectively conjugated to the surface of CdTe QDs. Column chromatography was used to purify the conjugates and determine the optimal ratio of dBSA to QDs. Further experimental results showed that the conjugation of QDs by dBSA efficiently improved the photoluminescence quantum yield, the chemical stability of QDs and their stability against photobleaching. A facile and sensitive method for determination of silver(I) ions was proposed based on the fluorescence quenching of the dBSA-QDs. Under the optimal conditions, the relative fluorescence intensity decreased linearly with the concentration of the silver(I) ions in the range 0.08-10.66 microM. The detection limit was 0.01 microM. This study provides a new method for the detection of metal cations.

Shake and break--shaking-induced changes of size quantization in aggregated quantum dots.

We show how simple mechanical agitation of precipitated CdSe quantum dot aggregates causes partially reversible color changes (clearly visible to the eye) in the absorption spectrum of the CdSe (about 4 nm size). The color changes, which are due to changes in size quantization, are not accompanied by change in quantum dot size. This phenomenon is explained by partial deaggregation of the precipitates, leading to reduced charge overlap between neighboring dots. Shaking was shown to result in a looser aggregate structure. It is suggested that CdSO3 particles (an initial product of the CdSe formation reaction) act as weak bridges between CdSe quantum dots, mediating the interparticle interactions and allowing the deaggregation to occur on shaking.

Highly efficient size separation of CdTe quantum dots by capillary gel electrophoresis using polymer solution as sieving medium.

In this paper, we present a new method for highly efficient size separation of water-soluble CdTe quantum dots (QDs) based on CGE using polymer solution as sieving medium. CdTe QDs were synthesized in aqueous phase by a chemical route with mercaptopropionic acid as a ligand. In the alkaline solution, CdTe QDs possess negative charges and migrate to the anode in the electric field. In linear polyacrylamide sieving medium, the migration time of CdTe QDs was increased with the size of CdTe QDs. The effects of some factors, such as types, concentrations, and pH of sieving media, on the separation of CdTe QDs were investigated systematically. Highly efficient separation of CdTe QDs was obtained in linear polyacrylamide sieving medium, and collection of fractions was automatically accomplished by CGE technique. Our preliminary results show that CGE technique is an efficient tool for characterization and size-dependent separation of water-soluble nanoparticles. In addition, the fraction collection in CGE may be useful in certain special applications such as fabrication of nanodevices in the future.

Microbial synthesis of semiconductor CdS nanoparticles, their characterization, and their use in the fabrication of an ideal diode.

Cadmium sulfide nanoparticles were synthesized intracellularly by a Schizosaccharomyces pombe strain when challenged with 1 mM cadmium in solution. The nanoparticles, a known semiconducting material, exhibited an absorbance maximum at 305 nm. X-ray scattering data showed that the nanoparticles had a Wurtzite (Cd(16)S(20))-type hexagonal lattice structure and most of the nanoparicles were in the size range of 1-1.5 nm. The nanoparticles were used in the fabrication of a heterojunction with poly (p-phenylenevinylene). The diode exhibited approximately 75 mA/cm(2) current at 10 V when forward biased and the breakdown occurred at approximately 15 V in the reverse biased mode. These characteristics are considered ideal for a diode.

A Raman study of CdSe and ZnSe nanostructures.

Raman studies have been carried out on CdSe nanotubes and ZnSe nanorods produced by surfactant-assisted synthesis. The Raman spectrum of CdSe nanotubes shows modes at 207.5 and 198 cm-1; the former arises from the longitudinal optic phonon mode red-shifted with respect to the bulk mode because of phonon confinement, and the latter is the l = 1 surface phonon. Analysis based on the phonon confinement model demonstrates that the size of the nanoparticle responsible for the red-shift is about 4 nm, close to the estimate from the blue-shift of the photoluminescence. The Raman spectrum of ZnSe nanorods shows modes at 257 and 213 cm-1, assigned to longitudinal and transverse optic phonons, blue-shifted with respect to the bulk ZnSe modes because of compressive strain. The mode at 237 cm-1 is the surface phonon.