ABSTRACT
The contamination of water sources by pharmaceutical pollutants presents significant environmental and health hazards, making the development of effective photocatalytic materials crucial for their removal. This research focuses on the synthesis of a novel Ag/CuS/Fe3O4 nanocomposite and its photocatalytic efficiency against tetracycline (TC) and diclofenac contaminants. The nanocomposite was created through a straightforward and scalable precipitation method, integrating silver nanoparticles (AgNPs) and copper sulfide (CuS) into a magnetite framework. Various analytical techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR),ultraviolet-visible spectrophotometry (UV-Vis) and energy-dispersive X-ray spectroscopy (EDS), were employed to characterize the structural and morphological properties of the synthesized material. The photocatalytic activity was tested by degrading tetracycline and diclofenac under visible light. Results indicated a marked improvement in the photocatalytic performance of the Ag/CuS/Fe3O4 nanocomposite (98%photodegradation of TC 60 ppm in 30 min) compared to both pure magnetite and CuS/Fe3O4. The enhanced photocatalytic efficiency is attributed to the synergistic interaction between AgNPs, CuS, and Fe3O4, which improves light absorption and charge separation, thereby increasing the generation of reactive oxygen species (ROS) and promoting the degradation of the pollutants. The rate constant k of photodegradation was about 0.1 min-1 for catalyst dosages 0.02 g. Also the effect of photocatalyst dose and concentration of TC and pH of solution was tested. The modified photocatalyst was also used for simultaneous photodegradation of TC and diclofenac successfully. This study highlights the potential of the Ag/CuS/Fe3O4 nanocomposite as an efficient and reusable photocatalyst for eliminating pharmaceutical pollutants from water.
Subject(s)
Copper , Diclofenac , Ferrosoferric Oxide , Nanocomposites , Silver , Tetracycline , Water Pollutants, Chemical , Diclofenac/chemistry , Nanocomposites/chemistry , Tetracycline/chemistry , Catalysis , Silver/chemistry , Ferrosoferric Oxide/chemistry , Water Pollutants, Chemical/chemistry , Copper/chemistry , Metal Nanoparticles/chemistry , Photolysis , X-Ray Diffraction , LightABSTRACT
Colorectal cancer represents a worldwide spread type of cancer and it is regarded as one of the leading death causes, along with lung, breast, and prostate cancers. Since conventional surgical resection and chemotherapy proved limited efficiency, the use of alternative drug delivery systems that ensure the controlled release of cytostatic agents possess immense potential for treatment. In this regard, the present study aimed to develop and evaluate the efficiency of a series of irinotecan-loaded magnetite-silica core-shell systems. The magnetite particles were obtained through a solvothermal treatment, while the silica shell was obtained through the Stöber method directly onto the surface of magnetite particles. Subsequently, the core-shell systems were physico-chemically and morpho-structurally evaluated trough X-ray diffraction (XRD) and (high-resolution) transmission electron microscopy ((HR-)TEM) equipped with a High Annular Angular Dark Field Detector (HAADF) for elemental mapping. After the irinotecan loading, the drug delivery systems were evaluated through Fourier-transform infrared spectroscopy (FT-IR), thermogravimetry and differential scanning calorimetry (TG-DSC), and UV-Vis spectrophotometry. Additionally, the Brunauer-Emmett-Teller (BET) method was employed for determining the surface area and pore volume of the systems. The biological functionality of the core-shells was investigated through the MTT assay performed on both normal and cancer cells. The results of the study confirmed the formation of highly crystalline magnetite particles comprising the core and mesoporous silica layers of sizes varying between 2 and 7 nm as the shell. Additionally, the drug loading and release was dependent on the type of the silica synthesis procedure, since the lack of hexadecyltrimethylammonium bromide (CTAB) resulted in higher drug loading but lower cumulative release. Moreover, the nanostructured systems demonstrated a targeted efficiency towards HT-29 colorectal adenocarcinoma cells, as in the case of normal L929 fibroblast cells, the cell viability was higher than for the pristine drug. In this manner, this study provides the means and procedures for developing drug delivery systems with applicability in the treatment of cancer.
Subject(s)
Cell Survival , Colorectal Neoplasms , Drug Liberation , Irinotecan , Silicon Dioxide , Irinotecan/administration & dosage , Irinotecan/chemistry , Silicon Dioxide/chemistry , Humans , Colorectal Neoplasms/drug therapy , Colorectal Neoplasms/pathology , Cell Survival/drug effects , Drug Carriers/chemistry , Drug Delivery Systems , Antineoplastic Agents, Phytogenic/administration & dosage , Antineoplastic Agents, Phytogenic/chemistry , Antineoplastic Agents, Phytogenic/pharmacology , Magnetite Nanoparticles/chemistry , Cell Line, Tumor , Ferrosoferric Oxide/chemistry , Ferrosoferric Oxide/administration & dosageABSTRACT
Conductive materials, such as magnetite, are recognized for their ability to enhance electron transfer and stimulate microbial metabolic activities. This study aimed to elucidate the metabolic potential and species interactions of dominant microbial species within complex communities influenced by magnetite. It indicated that the optimal dosage of magnetite at 4.5 mg/cm², would significantly improve denitrification efficiency and then reduce the time for removing 50 mg/L nitrate by 24.33 %. This enhancement was attributed to the reduced charge transfer resistance and the promoted formation of extracellular polymeric substances (EPS) facilitated by magnetite. Metagenomic analysis revealed that magnetite addition mitigated the competition among truncated denitrifiers for downstream nitrogen species, diminished the contribution of bacteria with complete nitrogen metabolism pathways to denitrification, and fostered a transition towards co-denitrification through interspecies cooperation, consequently leading to decreased nitrite accumulation and increased tolerance to nitrate shock loads. Furthermore, an in-depth study on a key species, Geobacter anodireducens JN93 within the bioelectrochemical system revealed that while magnetite with varying Fe(II) and Fe(III) ratios improved denitrification performance, the metabolic potential of Geobacter sp. varied for different nitrogen metabolism pathways. Collectively, this research provides insights into the microecological effects of magnetite on denitrifying consortia by shifting interspecific interactions via enhanced electron transfer.
Subject(s)
Denitrification , Ferrosoferric Oxide , Ferrosoferric Oxide/metabolism , Geobacter/metabolism , Nitrates/metabolism , Microbial Consortia , Bioreactors/microbiologyABSTRACT
Partial nitrification (PN) is crucial for anaerobic ammonium oxidation (ANAMMOX), but faces challenges such as high energy demands and process control. Recent research has highlighted additives like magnetite as potential alternatives to conventional electron acceptors (O2 and NO2-) for enhancing ammonium (NH4+) oxidation with lower energy consumption. This study investigated the effect of adding 50 mg/L of magnetite to ANAMMOX reactors, resulting in improved nitrogen (N) removal efficiency. The magnetite-added ANAMMOX (M-ANA) reactor yielded N removal efficiencies of 71 %, 66 %, and 57 % for NH4+:NO2- molar ratios of 1:1.3, 1:0.8, and 1:0.5, respectively. The M-ANA reactor operated under a 0.5 mol lower NO2- concentration achieved similar performance to the control ANAMMOX (C-ANA) reactor operated with a theoretical amount of NO2-. Moreover, the M-ANA reactor showed the potential to remove NH4+ by 56 % without any NO2- supplementation. Metagenomic analysis showed that the addition of magnetite significantly improved the relative abundance of microorganisms involved in the FEAMMOX reaction, such as Fimbriimonas ginsengisoli and Pseudomonas stutzeri. It also facilitated positive mutualism between ANAMMOX and FEAMMOX reactions. In addition, M-ANA granules exhibited a dense and compact structure compared with C-ANA, and the presence of magnetite facilitated the formation of resilient granules. Notably, the useful protein (Heme C) concentration and specific microbial activity in the M-ANA reactor were 1.3 and 2.2 times higher than those in the C-ANA reactor. Overall, the results demonstrate that an appropriate amount of magnetite can enhance the N removal efficiency while reducing the energy input requirements and associated carbon emissions. These findings can guide the future development of carbon- and energy-neutral N removal processes.
Subject(s)
Ammonium Compounds , Bioreactors , Ferrosoferric Oxide , Nitrites , Oxidation-Reduction , Waste Disposal, Fluid , Bioreactors/microbiology , Anaerobiosis , Waste Disposal, Fluid/methods , Nitrites/metabolism , Ammonium Compounds/metabolism , Nitrification , Bacteria/metabolismABSTRACT
A similarity-driven multi-dimensional binning algorithm (SIMBA) reconstruction of free-running cardiac magnetic resonance imaging data was previously proposed. While very efficient and fast, the original SIMBA focused only on the reconstruction of a single motion-consistent cluster, discarding the remaining data acquired. However, the redundant data clustered by similarity may be exploited to further improve image quality. In this work, we propose a novel compressed sensing (CS) reconstruction that performs an effective regularization over the clustering dimension, thanks to the integration of inter-cluster motion compensation (XD-MC-SIMBA). This reconstruction was applied to free-running ferumoxytol-enhanced datasets from 24 patients with congenital heart disease, and compared to the original SIMBA, the same XD-MC-SIMBA reconstruction but without motion compensation (XD-SIMBA), and a 5D motion-resolved CS reconstruction using the free-running framework (FRF). The resulting images were compared in terms of lung-liver and blood-myocardium sharpness, blood-myocardium contrast ratio, and visible length and sharpness of the coronary arteries. Moreover, an automated image quality score (IQS) was assigned using a pretrained deep neural network. The lung-liver sharpness and blood-myocardium sharpness were significantly higher in XD-MC-SIMBA and FRF. Consistent with these findings, the IQS analysis revealed that image quality for XD-MC-SIMBA was improved in 18 of 24 cases, compared to SIMBA. We successfully tested the hypothesis that multiple motion-consistent SIMBA clusters can be exploited to improve the quality of ferumoxytol-enhanced cardiac MRI when inter-cluster motion-compensation is integrated as part of a CS reconstruction.
Subject(s)
Algorithms , Ferrosoferric Oxide , Heart Defects, Congenital , Magnetic Resonance Imaging , Humans , Heart Defects, Congenital/diagnostic imaging , Magnetic Resonance Imaging/methods , Male , Female , Image Processing, Computer-Assisted/methods , Heart/diagnostic imaging , Heart/physiopathology , Motion , Adult , Child , Contrast Media , Adolescent , Young AdultABSTRACT
Neurogenesis is the process by which new brain cells are formed. This crucial event emerges during embryonic life and proceeds in adulthood, and it could be influenced by environmental pollution. Non-combustion-derived magnetite represents a portion of the coarse particulate matter (PM) contributing to air and water pollution in urban settings. Studies on humans have reported that magnetite and other iron oxides have significant damaging effects at a central level, where these particles accumulate and promote oxidative stress. Similarly, magnetite nanoparticles can cross the placenta and damage the embryo brain during development, but the impact on neurogenesis is still unknown. Furthermore, an abnormal Fe cation concentration in cells and tissues might promote reactive oxygen species (ROS) generation and has been associated with multiple neurodegenerative conditions. In the present study, we used zebrafish as an in vivo system to analyze the specific effects of magnetite on embryonic neurogenesis. First, we characterized magnetite using mineralogical and spectroscopic analyses. Embryos treated with magnetite at sub-lethal concentrations showed a dose-response increase in ROS in the brain, which was accompanied by a massive decrease in antioxidant genes (sod2, cat, gsr, and nrf2). In addition, a higher number of apoptotic cells was observed in embryos treated with magnetite. Next, interestingly, embryos exposed to magnetite displayed a decrease in neural staminal progenitors (nestin, sox2, and pcna markers) and a neuronal marker (elavl3). Finally, we observed significative increases in apoeb (specific microglia marker) and interleukin-1b (il1b), confirming a status of inflammation in the brain embryos treated with magnetite. Our study represents the very first in vivo evidence concerning the effects of magnetite on brain development.
Subject(s)
Embryo, Nonmammalian , Ferrosoferric Oxide , Neurogenesis , Zebrafish , Animals , Zebrafish/embryology , Neurogenesis/drug effects , Embryo, Nonmammalian/drug effects , Embryo, Nonmammalian/metabolism , Reactive Oxygen Species/metabolism , Oxidative Stress/drug effects , Brain/metabolism , Brain/drug effects , Brain/embryology , Apoptosis/drug effects , Magnetite Nanoparticles/chemistry , Magnetite Nanoparticles/toxicityABSTRACT
Herein, we constructed the branch-shaped SiO2/nano GO (nGO)/Fe3O4/selenium quantum dots (QDs) (SeQDs) nanoparticles (SGF/SeQDs) embodying magnetism, fluorescence, and microwave stimulus response properties to enhance the performance of releasing drugs. The SGF/SeQDs composite was characterized by technologies including powder X-ray diffraction, transmission electron microscopy, infrared spectroscopy, etc. In the nanoparticles, the branch-shaped SiO2 provides a large specific surface area, nGO as the dielectric loss-style material promotes microwave-absorbing performance, and the Fe3O4 serves as a magnetic targeting agent and microwave absorber. Integrating nGO and Fe3O4 could further strengthen the microwave absorption of the entire composite; selenium features both fluorescence and anticancer effects. The synthesized nanoparticles as carriers exhibited a branch-like mesoporous sphere of â¼260 nm, a specific surface area of 258.57 m2 g-1, a saturation magnetization of 24.59 emu g-1, and good microwave thermal conversion performance that the temperature was elevated from 25 to 70 °C under microwave irradiation. These physical characteristics, including large pore volume (5.30 nm), high specific surface area, and fibrous morphology, are in favor of loading drugs. Meanwhile, the cumulative etoposide (VP16) loading rate of the nanoparticles reached to 21 wt % after 360 min. The noncovalent interaction between the VP16 and SGF/SeQDs was mainly the hydrogen-bonding effect during the loading process. Furthermore, the drug release rates at 180 min were up to 81.46, 61.92, and 56.84 wt % at pH 4, 5, and 7, respectively. At 25, 37, and 50 °C, the rates of drug release reach 25.40, 56.84, and 65.32 wt %, respectively. After microwave stimulation at pH 7, the rate of releasing drug increased distinctly from 56.84 to 71.74 wt % compared to that of nonmicrowave irradiation. Cytotoxicity tests manifested that the carrier had good biocompatibility. Therefore, the nanoparticles are looking forward to paving one platform for further applications in biomedicine and drug delivery systems.
Subject(s)
Drug Carriers , Quantum Dots , Selenium , Silicon Dioxide , Silicon Dioxide/chemistry , Drug Carriers/chemistry , Drug Carriers/chemical synthesis , Humans , Quantum Dots/chemistry , Quantum Dots/toxicity , Selenium/chemistry , Microwaves , Drug Liberation , Nanoparticles/chemistry , Cell Survival/drug effects , Etoposide/chemistry , Etoposide/pharmacology , Antineoplastic Agents/chemistry , Antineoplastic Agents/pharmacology , Particle Size , Surface Properties , Ferrosoferric Oxide/chemistryABSTRACT
BACKGROUND: Rapid on-site detection of infectious diseases is considerably essential for preventing and controlling major epidemics and maintaining social and public safety. However, the complexity of the natural environment in which infectious disease pathogens exist severely disrupts the performance of on-site detection, and rapid detection can become meaningless because of the cumbersome sample pretreatment process. RESULT: Herein, a new detection platform based on a carbon sphere@Fe3O4 micromotor (CS@Fe3O4) in combination with a graphene field-effect transistor (GFET) was designed and used for the on-site detection of SARS-CoV-2 coronavirus pathogens. The CS@Fe3O4 micromotor, surface-modified with anti-SARS-CoV-2 coronavirus antibody, could move at a velocity of 79.4 µm/s in a solution containing hydrogen peroxide (H2O2) and exhibited capture rates of 67.9% and 36.2% for the SARS-CoV-2 pathogen in phosphate buffered saline (PBS) and soil solutions, respectively. After magnetic field separation, the captured micromotor was used for GFET detection, with detection limits of 4.6 and 15.6 ag/mL in PBS and soil solutions, respectively. SIGNIFICANCE AND NOVELTY: This detection platform can be employed to avoid complex sample pretreatment procedures and achieve rapid on-site detection of SARS-CoV-2 coronavirus pathogens in complex environments. This study introduces a novel approach for the on-site detection of infectious diseases.
Subject(s)
COVID-19 , Carbon , Graphite , SARS-CoV-2 , Transistors, Electronic , Graphite/chemistry , SARS-CoV-2/isolation & purification , SARS-CoV-2/immunology , COVID-19/diagnosis , COVID-19/virology , Carbon/chemistry , Humans , Limit of Detection , Biosensing Techniques/methods , Hydrogen Peroxide/chemistry , Ferrosoferric Oxide/chemistryABSTRACT
Despite benefits such as lower water and working volume requirements, thermophilic high solids anaerobic digestion (THSAD) often fails due to the rapid build-up of volatile fatty acids (VFAs) and the associated drop in pH. Use of conductive materials (CM) can promote THSAD through stimulation of direct interspecies electron transfer (DIET), while the need for their constant dosing due to poor separation from effluent impairs economic feasibility. This study used an approach of spatially separating magnetite and granular activated carbon (GAC) from the organic fraction of municipal solid waste (OFMSW) in a single reactor for THSAD. GAC and magnetite addition could both mitigate the severe inhibition of methanogenesis after VFAs build-up to â¼28-30 g/L, while negligible methane production was observed in the control group. The highest methane yield (286 mL CH4/g volatile solids (VS)) was achieved in magnetite-added reactors, while the highest maximum CH4 production rates (26.38 mL CH4/g VS/d) and lowest lag-phase (2.83 days) were obtained in GAC-added reactors. The enrichment of GAC and magnetite biofilms with various syntrophic and potentially electroactive microbial groups (Ruminiclostridium 1, Clostridia MBA03, Defluviitoga, Lentimicrobiaceae) in different relative abundances indicates the existence of specific preferences of these groups for the nature of CM. According to predicted basic metabolic functions, CM can enhance cellular processes and signals, lipid transport and metabolism, and methane metabolism, resulting in improved methane production. Rearrangement of metabolic pathways, formation of pili-like structures, enrichment of biofilms with electroactive groups and a significant improvement in THSAD performance was attributed to the enhancement of the DIET pathway. Promising results obtained in this work due to the spatial separation of the bulk OFMSW and CM can be useful for modeling larger-scale THSAD systems with better recovery of CM and cost-effectiveness.
Subject(s)
Bioreactors , Methane , Solid Waste , Anaerobiosis , Methane/metabolism , Fatty Acids, Volatile/metabolism , Refuse Disposal/methods , Ferrosoferric Oxide/chemistryABSTRACT
BACKGROUND: Imaging evaluation of acute deep vein thrombosis (DVT) or post-thrombotic syndrome (PTS) in animal or clinical models is limited to anatomical assessment of the location and extent of thrombi. We hypothesize that Fe-MRI, used to evaluate macrophage content in other inflammatory diseases, can be useful to evaluate the thromboinflammatory features after DVT over time. METHODS: Nineteen wild-type CD-1 mice underwent surgical IVC ligation to induce DVT. Mice received either saline or 5 mg/kg of 14E11, a Factor XI inhibitor, before the procedure. Fe-MRI was performed on days 6-7 after ligation to evaluate thrombus volume, perfusion, and macrophage content via T2-weighted images. Mice were euthanized at days 3-15 after surgery. The thrombi and adjacent vein walls were excised, weighed, formalin-fixed, and paraffin-embedded for immunohistological analysis. Specimens were stained with specific antibodies to evaluate macrophage content, collagen deposition, neovascularization, and recanalization. Significance was determined using the Mann-Whitney U or Student's t-test. RESULTS: After IVC-ligation in control mice, thrombus weights decreased by 59 % from day 3 to 15. Thrombus volumes peaked on day 5 before decreasing by 85 % by day 13. FXI inhibition led to reduced macrophage content in both thrombi (p = .008) and vein walls (p = .01), decreased thrombus volume (p = .03), and decreased thrombus mass (p = .01) compared to control mice. CCR2+ staining corroborated these findings, showing significantly reduced macrophage presence in the thrombi (p = .002) and vein wall (p = .002). CONCLUSIONS: Fe-MRI T2 relaxation times can be used to characterize and quantify post-thrombotic changes of perfusion, macrophage content, and thrombus volume over time in a surgical mouse model of venous thrombosis. This approach could lead to better quantification of in vivo inflammation correlating monocyte and macrophage content within resolving thrombi and veins and may serve as a useful tool for research and clinically in the evaluation of the post-thrombotic environment.
Subject(s)
Disease Models, Animal , Ferrosoferric Oxide , Macrophages , Magnetic Resonance Imaging , Venous Thrombosis , Animals , Venous Thrombosis/diagnostic imaging , Venous Thrombosis/pathology , Mice , Macrophages/pathology , Magnetic Resonance Imaging/methods , Male , Contrast MediaABSTRACT
The enumeration of circulating tumor cells (CTCs) in peripheral blood plays a crucial role in the early diagnosis, recurrence monitoring, and prognosis assessment of cancer patients. There is a compelling need to develop an efficient technique for the capture and identification of these rare CTCs. However, the exclusive reliance on a single criterion, such as the epithelial cell adhesion molecule (EpCAM) antibody or aptamer, for the specific recognition of epithelial CTCs is not universally suitable for clinical applications, as it usually falls short in identifying EpCAM-negative CTCs. To address this limitation, we propose a straightforward and cost-effective method involving triplex fluorescently labelled aptamers (FAM-EpCAM, Cy5-PTK7, and Texas Red-CSV) to modify Fe3O4-loaded dendritic SiO2 nanocomposite (dmSiO2@Fe3O4/Apt). This multi-recognition-based strategy not only enhanced the efficiency in capturing heterogeneous CTCs, but also facilitated the rapid and accurate identification of CTCs. The capture efficiency of heterogenous CTCs reached up to 93.33%, with a detection limit as low as 5 cells/mL. Notably, the developed dmSiO2@Fe3O4/Apt nanoprobe enabled the swift identification of captured cells in just 30 min, relying solely on the fluorescently modified aptamers, which reduced the identification time by approximately 90% compared with the conventional immunocytochemistry (ICC) technique. Finally, these nanoprobe characteristics were validated using blood samples from patients with various types of cancers.
Subject(s)
Aptamers, Nucleotide , Fluorescent Dyes , Nanocomposites , Neoplastic Cells, Circulating , Silicon Dioxide , Humans , Neoplastic Cells, Circulating/pathology , Silicon Dioxide/chemistry , Aptamers, Nucleotide/chemistry , Nanocomposites/chemistry , Fluorescent Dyes/chemistry , Immunomagnetic Separation/methods , Epithelial Cell Adhesion Molecule/immunology , Limit of Detection , Cell Line, Tumor , Ferrosoferric Oxide/chemistryABSTRACT
Magnetomicelles were produced by the self-assembly of magnetite iron oxide nanoflowers and the amphiphilic poly(styrene)-b-poly(acrylic acid) block copolymer to deliver a multifunctional theranostic agent. Their bioprocessing by cancer cells was investigated in a three-dimensional spheroid model over a 13-day period and compared with nonencapsulated magnetic nanoflowers. A degradation process was identified and monitored at various scales, exploiting different physicochemical fingerprints. At a collective level, measurements were conducted using magnetic, photothermal, and magnetic resonance imaging techniques. At the nanoscale, transmission electron microscopy was employed to identify the morphological integrity of the structures, and X-ray absorption spectroscopy was used to analyze the degradation at the crystalline phase and chemical levels. All of these measurements converge to demonstrate that the encapsulation of magnetic nanoparticles in micelles effectively mitigates their degradation compared to individual nonencapsulated magnetic nanoflowers. This protective effect consequently resulted in better maintenance of their therapeutic photothermal potential. The structural degradation of magnetomicelles occurred through the formation of an oxidized iron phase in ferritin from the magnetic nanoparticles, leaving behind empty spherical polymeric ghost shells. These results underscore the significance of encapsulation of iron oxides in micelles in preserving nanomaterial integrity and regulating degradation, even under challenging physicochemical conditions within cancer cells.
Subject(s)
Magnetite Nanoparticles , Micelles , Polystyrenes , Humans , Magnetite Nanoparticles/chemistry , Polystyrenes/chemistry , Acrylic Resins/chemistry , Cell Line, Tumor , Ferrosoferric Oxide/chemistry , AcrylatesABSTRACT
This study examined the combination of activated carbon and magnetite with calcium peroxide in enhancing the anaerobic digestion (AD) performance of food waste (FW). The individual mechanisms of these two approaches were also clarified. The results indicated that AC/CaO2 achieved the highest specific methane yield of 434.4 mL/g VS, followed by Fe3O4/CaO2 (416.9 mL/g VS). Both were significantly higher than other groups (control, AC, Fe3O4, and CaO2 were 330.1, 341.4, 342.8, and 373.2 mL/g VS, respectively). Additionally, compared to Fe3O4/CaO2, AC/CaO2 further increased reactive oxygen species (ROS), thereby enhancing the hydrolytic acidification process. Simultaneously, the higher ROS levels of Fe3O4/CaO2 and AC/CaO2 promoted the formation of microbial aggregates and established a more robust enzymatic defense system and unique damage repair strategy. The research comparatively analyzed the synergistic mechanism of iron-based and carbon-based conductive materials with CaO2, providing new perspectives for optimizing the AD of FW.
Subject(s)
Methane , Reactive Oxygen Species , Methane/metabolism , Reactive Oxygen Species/metabolism , Anaerobiosis , Charcoal/chemistry , Peroxides , Calcium Compounds/chemistry , Ferrosoferric Oxide/chemistry , Oxides/chemistryABSTRACT
Despite the growing prevalence of nanoplastics in drinking water distribution systems, the collective influence of nanoplastics and background nanoparticles on biofilm formation and microbial risks remains largely unexplored. Here, we demonstrate that nano-sized polystyrene modified with carboxyl groups (nPS) and background magnetite (nFe3O4) nanoparticles at environmentally relevant concentrations can collectively stimulate biofilm formation and prompt antibiotic resistance. Combined exposure of nPS and nFe3O4 by P. aeruginosa biofilm cells stimulated intracellular reactive oxidative species (ROS) production more significantly compared with individual exposure. The resultant upregulation of quorum sensing (QS) and c-di-GMP signaling pathways enhanced the biosynthesis of polysaccharides by 50 %- 66 % and increased biofilm biomass by 36 %- 40 % relative to unexposed control. Consistently, biofilm mechanical stability (measured as Young's modulus) increased by 7.2-9.1 folds, and chemical stress resistance (measured with chlorine disinfection) increased by 1.4-2.0 folds. For P. aeruginosa, the minimal inhibitory concentration of different antibiotics also increased by 1.1-2.5 folds after combined exposure. Moreover, at a microbial community-wide level, metagenomic analysis revealed that the combined exposure enhanced the multi-species biofilm's resistance to chlorine, enriched the opportunistic pathogenic bacteria, and promoted their virulence and antibiotic resistance. Overall, the enhanced formation of biofilms (that may harbor opportunistic pathogens) by nanoplastics and background nanoparticles is an overlooked phenomenon, which may jeopardize the microbial safety of drinking water distribution systems.
Subject(s)
Anti-Bacterial Agents , Biofilms , Oxidative Stress , Polystyrenes , Pseudomonas aeruginosa , Reactive Oxygen Species , Biofilms/drug effects , Oxidative Stress/drug effects , Pseudomonas aeruginosa/drug effects , Polystyrenes/toxicity , Polystyrenes/chemistry , Anti-Bacterial Agents/pharmacology , Anti-Bacterial Agents/chemistry , Anti-Bacterial Agents/toxicity , Reactive Oxygen Species/metabolism , Nanoparticles/toxicity , Nanoparticles/chemistry , Ferrosoferric Oxide/chemistry , Ferrosoferric Oxide/toxicity , Quorum Sensing/drug effects , Drug Resistance, Bacterial/drug effects , Magnetite Nanoparticles/toxicity , Magnetite Nanoparticles/chemistry , Microbial Sensitivity TestsABSTRACT
V-Ti magnetite tailings (VTMTs) contain various heavy metals, such as Fe, Mn, V, Co, and Ni. The groundwater pollution caused by the tailing metal release has become a local environmental concern. Although studies have demonstrated the influence of alternate flooding and drying cycles (FDCs) on metal form and mobility in minerals, little was known about whether FDCs affect the metal release of VTMTs and the transformation of released metals. This study investigated the metal release kinetics of VTMTs and the metal transformation under FDCs in the absence and presence of acid rain (sulfuric and nitric acids) and bio-secreted organic acids (acetic, oxalic, and citric acids). The results showed that FDCs promoted metal release whether or not acids were present. The maximum released concentrations of V, Mn, Fe, Co, and Ni were as high as 78.63 mg L-1,1.47 mg L-1, 67.96 µg L-1, 1.34 mg L-1, and 0.80 mg L-1, respectively, under FDCs and citric acids. FDCs enhanced the tailing metal release by increasing the metal labile fraction proportion. However, the concentrations of released Fe, Mn, V, Co, and Ni all gradually decreased due to their (co-)precipitation. These precipitates conversely inhibited the subsequent mineral dissolution by covering the tailing surface. FDCs also enhanced the tailings' porosities by 2.94%-9.94%. The mineral dissolution, expansion and shrinkage, and changes in tension destroyed the tailing microstructure during FDCs. This study demonstrated the low metal pollution risk of VTMTs under FDCs, either in acid rain or bio-secreted organic acids. However, the increase in tailing porosity should be seriously considered as it would affect the tailing pond safety.
Subject(s)
Metals, Heavy , Metals, Heavy/analysis , Ferrosoferric Oxide/chemistry , Water Pollutants, Chemical/analysis , Floods , Groundwater/chemistry , Mining , Desiccation , Acid Rain , KineticsABSTRACT
We describe a case of anaphylaxis during administration of intravenous (IV) ferumoxytol as a magnetic resonance imaging (MRI) contrast agent in a 4-year-old patient with complicated past medical history including YARS genetic mutation with resultant liver failure and deceased donor liver transplantation, stage IV chronic kidney disease (CKD), and hypertension. The patient was noted to have labored breathing 4 min after initiation of ferumoxytol infusion and was subsequently rapidly intubated and returned to the intensive care unit (ICU) for monitoring. Anaphylactic reactions to therapeutic doses of ferumoxytol led to issuance of a black box warning by the FDA in 2015. Adverse reactions to lower-dose ferumoxytol used in diagnostic imaging, however, are rare and there has been a paucity of documented anaphylactic reactions in the literature.
Subject(s)
Anaphylaxis , Contrast Media , Ferrosoferric Oxide , Magnetic Resonance Imaging , Humans , Anaphylaxis/chemically induced , Child, Preschool , Contrast Media/adverse effects , Ferrosoferric Oxide/adverse effects , Ferrosoferric Oxide/administration & dosage , MaleABSTRACT
The qualitative composition and zeta potential of magnetite nanoparticles (size 4.2±1.2 nm) obtained by co-precipitation method were determined by X-ray and diffraction dynamic light scattering. The zeta potential of Fe3O4 particles was -15.1±4.5 mV. The possibility of interaction of magnetite nanoparticles with human blood plasma proteins and hemoglobin as well as with erythrocyte membranes was demonstrated by spectrophotometry, electrophoresis, and fluorescence methods. No changes in the sizes of hemoglobin molecules and plasma proteins after their modification by Fe3O4 particles were detected. The possibility of modifying the structural state of erythrocyte membranes in the presence of magnetite nanoparticles was demonstrated by means of fluorescent probe 1-anilinonaphthalene-8-sulfonate.
Subject(s)
Hemoglobins , Magnetite Nanoparticles , Humans , Magnetite Nanoparticles/chemistry , Hemoglobins/chemistry , Erythrocyte Membrane/drug effects , Erythrocyte Membrane/chemistry , Erythrocyte Membrane/metabolism , Particle Size , Blood Proteins/chemistry , Anilino Naphthalenesulfonates/chemistry , X-Ray Diffraction , Ferrosoferric Oxide/chemistry , Fluorescent Dyes/chemistryABSTRACT
Despite the increased research efforts aimed at understanding iron-based conductive materials (CMs) for facilitating chain elongation (CE) to produce medium chain fatty acids (MCFAs), the impact of these materials on microbial community functions and the adaptation mechanisms to their biotoxicity remain unclear. This study found that the supply of zero-valent iron (ZVI) and magnetite enhanced the MCFAs carbon-flow distribution by 26 % and 52 %, respectively. Metagenomic analysis revealed the upregulation of fatty acid metabolism, pyruvate metabolism and ABC transporters with ZVI and magnetite. The predominant functional microorganisms were Massilibacterium and Tidjanibacter with ZVI, and were Petrimonas and Candidatus_Microthrix with magnetite. Furthermore, it was demonstrated that CE microorganisms respond and adapt to the biotoxicity of iron-based CMs by adjusting Two-component system and Quorum sensing for the first time. In summary, this study provided a new deep-insight on the feedback mechanisms of CE microorganisms on iron-based CMs.
Subject(s)
Iron , Iron/pharmacology , Iron/metabolism , Adaptation, Physiological/drug effects , Fatty Acids/metabolism , Bacteria/metabolism , Bacteria/drug effects , Ferrosoferric Oxide/chemistry , Quorum Sensing/drug effectsABSTRACT
Arsenic (As) cycling in groundwater is commonly coupled to the biogeochemical cycling of iron (Fe) and the associated transformation of Fe minerals present. Numerous laboratory studies suggested that Fe minerals can act as nucleation sites for further crystal growth and as catalysts for abiotic Fe(II) oxidation. In view of the widespread existence of magnetite in anoxic environments where As is often dissolved, we firstly exploited magnetite to enhance As immobilization during nitrate-reducing Fe(II) oxidation (NRFO) induced by Acidovorax sp. strain BoFeN1, a mixotrophic nitrate-reducing Fe(II)-oxidizing bacterium that can oxidize Fe(II) through both enzymatic and abiotic pathways. Subsequently, we investigated how magnetite affects NRFO and As immobilization. Results demonstrated a significant increase in As(III) removal efficiency from 75.4 % to 97.2 % with magnetite, attributed to the higher amount of NRFO and As(III) oxidation promoted by magnetite. It was found that magnetite stimulated the production of extracellular polymeric substances (EPS), which could decrease the diffusion of nitrate in the periplasm of bacteria and shield them against encrustation, resulting in a more rapid reduction of nitrate in the system with magnetite than that without magnetite. Meanwhile, Fe(II) was almost completely oxidized in the presence of magnetite during the whole 72 h experiment, while in the absence of magnetite, 47.7 % of Fe(II) remained, indicating that magnetite could obviously accelerate the chemical oxidation of Fe(II) with nitrite (the intermediates of nitrate bioreduction). Furthermore, the formation of labile Fe(III), an intermediate product of electron transfer between Fe(II) and magnetite, was reasonably deduced to be vital for anoxic As(III) oxidation. Additionally, the XPS analysis of the solid phase confirmed the oxidation of 43.8 % of As(III) to As(V). This study helps to understand the biogeochemical cycling of Fe and As in the environment, and provides a cost-effective and environmentally friendly option for in situ remediation of As-contaminated groundwater.
Subject(s)
Arsenic , Comamonadaceae , Ferrosoferric Oxide , Nitrates , Oxidation-Reduction , Water Pollutants, Chemical , Nitrates/metabolism , Comamonadaceae/metabolism , Ferrosoferric Oxide/metabolism , Water Pollutants, Chemical/metabolism , Arsenic/metabolism , Groundwater/chemistry , Groundwater/microbiology , Ferrous Compounds/metabolism , Iron/metabolism , Iron/chemistryABSTRACT
This study aims to evaluate the feasibility of an innovative reusable adsorbent through adsorption-degradation sequence for antibiotic removal from water. The magnetite/mesoporous carbon adsorbent was prepared using a two-step method of (i) in situ impregnation of magnetite precursor during resorcinol formaldehyde polymerization and (ii) pyrolysis at elevated temperature (800 °C). XRD spectra confirmed that magnetite (Fe3O4) was the only iron oxide species present in the adsorbent, and thermogravimetric analysis revealed that its content was 10 wt%. Nitrogen sorption analysis showed that Fe3O4/carbon features a high fraction of mesopores (> 80 vol.%) and a remarkable specific surface area value (246 m2 g-1), outstanding properties for water treatment. The performance of the adsorbent was examined in the uptake of three relevant antibiotics. The maximum adsorption uptakes were ca. 76 mg g-1, ca. 70 mg g-1, and ca. 44 mg g-1 for metronidazole, sulfamethoxazole, and ciprofloxacin, respectively. All adsorption curves were successfully fitted with Langmuir equilibrium model. The regeneration of adsorbent was carried out using Fenton oxidation under ambient conditions. After three consecutive runs of adsorption-regeneration, Fe3O4/carbon maintained its performance almost unchanged (up to 95% of its adsorption capacity), which highlights the high reusability of the adsorbent.