Simultaneous Quantitative Analysis of Six Proton-Pump Inhibitors with a Single Marker and Evaluation of Stability of Investigated Drugs in Polypropylene Syringes for Continuous Infusion Use.

OBJECTIVE: We developed and validated a simple, convenient and reproducible method for simultaneous estimation of six proton-pump inhibitors (PPIs), omeprazole (OPZ), esomeprazole (EOPZ), lansoprazole (LPZ), pantoprazole (PPZ), rabeprazole (RPZ) and ilaprazole (IPZ) in pharmaceutical dosage forms by a single marker. Meanwhile, the stability of the cited PPIs in 0.9% sodium chloride injection stored in polypropylene syringes up to 48 hours for continuous infusion use was investigated. MATERIALS AND METHODS: The chromatographic separation was achieved on an InterSustain® C18 column (150 × 4.6 mm, 5 µm). The isocratic mobile phase made up of 0.05 M potassium dihydrogen phosphate buffer (pH 4.0): acetonitrile (65:35, v/v) was pumped through the column at a temperature maintained at 30°C and a flow rate of 1.0 mL/min. The relative retention time, UV spectral similarity and relative correction factors between OPZ and the other five PPIs were calculated and investigated using the quantitative analysis of multi-components with a single marker (QAMS) method. The stability study examined physical parameters, pH values and drug concentrations of the PPIs mixtures. RESULTS: Under these conditions, all cited PPIs were separated simultaneously at a retention time of 6.0, 7.3, 7.3, 9.9, 12.5 and 13.9 min for RPZ, OPZ, EOPZ, IPZ, PPZ and LPZ, respectively, with a total run time less than 20.0 min. Comparative analysis results indicated that there were no significant differences observed between the QAMS method and the external standard method. The percentage of initial concentration of each PPI gradually decreased during the storage time. CONCLUSION: The proposed method, which is selective, economical and accurate, was applied successfully for determination of the cited PPIs in their respective pharmaceutical dosage forms. Admixtures of OPZ, EOPZ, PPZ, IPZ in 0.9% sodium chloride injection were stable for 24 hours and LPZ, RPZ in 0.9% sodium chloride injection were stable for 8 hours in polypropylene syringes.

Chiral separation of lansoprazole and rabeprazole by capillary electrophoresis using dual cyclodextrin systems.

Novel capillary electrophoresis methods using CDs as chiral selectors were developed and validated for the chiral separation of lansoprazole and rabeprazole, two proton pump inhibitors. Fourteen different neutral and anionic CDs were screened at pH 4 and 7 in the preliminary analysis. Sulfobutyl-ether-ß-CD with a degree of substitution of 6.5 and 10 at neutral pH proved to be the most suitable chiral selector for both compounds. Various dual CD systems were also compared, and the possible mechanisms of enantiomer separation were investigated. A dual selector system containing sulfobutyl-ether-ß-CD degree of substitution 6.5 and native γ-CD proved to be the most adequate system for the separations. Method optimization was carried out using an experimental design approach, performing an initial fractional factorial screening design, followed by a central composite design to establish the optimal analytical conditions. The optimized methods (25 mM phosphate buffer, pH 7, 10 mM sulfobutyl-ether-ß-CD/20 mM γ-CD, +20 kV voltage; 17°C temperature; 50 mbar/3 s injection, detection at 210 nm for lansoprazole; 25 mM phosphate buffer, pH 7, 15 mM sulfobutyl-ether-ß-CD/30 mM γ-CD, +20 kV voltage; 18°C temperature; 50 mbar/3 s injection, detection at 210 nm for rabeprazole) provided baseline separation for lansoprazole (Rs = 2.91) and rabeprazole (Rs = 2.53) enantiomers with favorable migration order (in both cases the S-enantiomers migrates first). The optimized methods were validated according to current guidelines and proved to be reliable, linear, precise, and accurate for the determination of 0.15% distomer as chiral impurity in dexlansoprazole and dexrabeprazole samples.

A Highly Efficient Chemiluminescence System Based on an Enhancing Effect of Ag Nanoclusters/Graphene Quantum Dots Mixture for Ultrasensitive Detection of Rabeprazole.

Herein, an efficient chemiluminescence (CL) reaction with a high emission intensity is reported based on a synergistic improving effect of silver nanoclusters (AgNCs) and graphene quantum dots (GQDs). First, the syntheses of AgNCs and GQDs were simply performed by the chemical reducing of AgNO3 and a thermal treatment of glucose, respectively. After the characterization steps, the beneficial behavior of the prepared nanomaterial was investigated in CL systems. The oxidation reaction of KMnO4-rhodamine B produced weak CL emission. However, the presence of AgNCs and GQDs led to a synergetic enhancing effect, and thus higher emission was obtained. A possible mechanism was investigated for this effect using absorption and fluorescence experiments. Furthermore, rabeprazole showed a relatively selective enhancing impact on the CL emission. The CL intensity was linearly increased in the rabeprazole concentration range of 4 - 133 ng mL-1 with a detection limit (3Sb/m) of 1.1 ng mL-1. The developed CL method was utilized for the measurement of Rbp in biological samples with acceptable precision and accuracy.

Analysis of potential genotoxic impurities in rabeprazole active pharmaceutical ingredient via Liquid Chromatography-tandem Mass Spectrometry, following quality-by-design principles for method development.

A novel Liquid Chromatography-tandem mass spectrometry (LC-MS/MS) method is presented for the quantitative determination of two potential genotoxic impurities (PGIs) in rabeprazole active pharmaceutical ingredient (API). In order to overcome the analytical challenges in the trace analysis of PGIs, a development procedure supported by Quality-by-Design (QbD) principles was evaluated. The efficient separation between rabeprazole and the two PGIs in the shortest analysis time was set as the defined analytical target profile (ATP) and to this purpose utilization of a switching valve allowed the flow to be sent to waste when rabeprazole was eluted. The selected critical quality attributes (CQAs) were the separation criterion s between the critical peak pair and the capacity factor k of the last eluted compound. The effect of the following critical process parameters (CPPs) on the CQAs was studied: %ACN content, the pH and the concentration of the buffer salt in the mobile phase, as well as the stationary phase of the analytical column. D-Optimal design was implemented to set the plan of experiments with UV detector. In order to define the design space, Monte Carlo simulations with 5000 iterations were performed. Acceptance criteria were met for C8 column (50×4mm, 5µm), and the region having probability π≥95% to achieve satisfactory values of all defined CQAs was computed. The working point was selected with the mobile phase consisting of ACN, ammonium formate 11mM at a ratio 31/69v/v with pH=6,8 for the water phase. The LC protocol was transferred to LC-MS/MS and validated according to ICH guidelines.

Determination of rabeprazole enantiomers in commercial tablets using immobilized cellulose-based stationary phase.

Rabeprazole is one of the latest proton-pump inhibitors used for treatment of several gastrointestinal disorders. For therapeutic applications, rabeprazole has been administered as a mixture of R-(+) and S-(-) enantiomers. Owing to pharmacological and toxicological differences between stereoisomers, chiral recognition has now become an integral part of drug research and development. A simple and rapid liquid chromatographic method for enantioselective separation and determination of R-(+) and S-(-) enantiomers of rabeprazole in bulk drug and pharmaceutical formulations was developed. Chiralpak IC (150 × 4.6 mm, 5 µm) column and µmobile phase containing hexane:ethanol:ethylenediamine (30:70:0.05 v/v) in an isocratic mode yielded baseline separation with resolution greater than 6.0 at 35 °C. Effects of additives and n-hexane were evaluated. Optimized condition was validated as per ICH guidelines. The method has good linearity, high sensitivity with LOD was 0.01 µg/mL and LOQ was 0.03 µg/mL for both enantiomers. Intra-day precision varied between 0.44 and 1.79% for S-(-) enantiomer, 0.65 and 1.97% for R-(+) enantiomer. Relative standard deviations of inter-day precision were less than 1.81% for both enantiomers. The percentage recovery for both enantiomers of rabeprazole ranged between 99.81 and 101.95%, 98.82 and 101.36% in material and tablets, respectively. The method was successfully applied to determine content of each enantiomer in commercial tablets.

Combining simplicity with cost-effectiveness: Investigation of potential counterfeit of proton pump inhibitors through simulated formulations using thin-layer chromatography.

A simple, accurate and precise high-performance thin-layer chromatographic method has been developed and validated for the analysis of proton pump inhibitors (PPIs) and their co-formulated drugs, available as binary combination. Planar chromatographic separation was achieved using a single mobile phase comprising of toluene: iso-propranol: acetone: ammonia 5.0:2.3:2.5:0.2 (v/v/v/v) for the analysis of 14 analytes on aluminium-backed layer of silica gel 60 FG254. Densitometric determination of the separated spots was done at 290nm. The method was validated according to ICH guidelines for linearity, precision and accuracy, sensitivity, specificity and robustness. The method showed good linear response for the selected drugs as indicated by the high values of correlation coefficients (≥0.9993). The limit of detection and limit of quantiation were in the range of 6.9-159.2ng/band and 20.8-478.1ng/band respectively for all the analytes. The optimized conditions afforded adequate resolution of each PPI from their co-formulated drugs and provided unambiguous identification of the co-formulated drugs from their homologous retardation factors (hRf). The only limitation of the method was the inability to separate two PPIs, rabeprazole and lansoprazole from each other. Nevertheless, it is proposed that peak spectra recording and comparison with standard drug spot can be a viable option for assignment of TLC spots. The method performance was assessed by analyzing different laboratory simulated mixtures and some marketed formulations of the selected drugs. The developed method was successfully used to investigate potential counterfeit of PPIs through a series of simulated formulations with good accuracy and precision.

Development and validation of HPLC-DAD method for the simultaneous determination of amoxicillin, metronidazole and rabeprazole sodium. Application to spiked simulated intestinal fluid samples.

This work deals with the development, validation and application of an HPLC-DAD method for the determination of a ternary mixture containing amoxicillin (AX), metronidazole (MZ) and the proton pump inhibitor rabeprazole sodium (RB). This triple therapy is used for treatment of Helicobacter pylori infection. Effective chromatographic separation between the three drugs was achieved using Thermo Hypersil BDS-C8 (4.6×250mm, 5µm particle size) column and a mobile phase composed of phosphate buffer pH 7 and acetonitrile (70: 30, by volume). The mobile phase was pumped isocratically at a flow rate of 1 mL/min. Quantification of the analytes was based on measuring their peak areas at 230nm for both AX and RB, and at 319nm for MZ. AX, MZ and RB eluted at retention times 2.36, 3.55 and 8.72min respectively. The reliability and analytical performance of the proposed HPLC procedure were statistically validated with respect to linearity, ranges, precision, accuracy, selectivity, robustness, detection and quantification limits. The linear dynamic ranges were 25-250, 25-250 and 5-50µg/mL for AX, MZ and RB respectively with correlation coefficients>0.9998. The validated method was successfully applied to the analysis of several laboratory-prepared mixtures as well as simulated intestinal fluid samples spiked with the three drugs.

Spectrophotometric methods manipulating ratio spectra for simultaneous determination of binary mixtures with sever overlapping spectra: a comparative study.

Three simple, specific and accurate spectrophotometric methods manipulating ratio spectra were developed and validated for simultaneous determination of Rabeprazole sodium (RB) and Domperidone (DP) in their binary mixture without prior separation. Method A, is constant center spectrophotometric method (CC). Method B is a ratio difference spectrophotometric one (RD), while method C is a combined ratio isoabsorptive point-ratio difference method (RIRD). Linear correlations were obtained in range of 4-44µg/mL for both Rabeprazole sodium and Domperidone. The mean percentage recoveries of RB were 99.69±0.504 for method A, 99.83±0.483 for (B) and 100.31±0.499 for (C), respectively, and that of DP were 99.52±0.474 for method A, 100.12±0.505 for (B) and 100.16±0.498 for (C), respectively. Specificity was investigated by analysis of laboratory prepared mixtures containing the cited drugs and their combined tablet dosage form. The obtained results were statistically compared with those obtained by the reported methods, showing no significant difference with respect to accuracy and precision. The three methods were validated as per ICH guidelines and can be applied for routine analysis in quality control laboratories.

Liquid chromatography coupled with fluorimetric detection and third derivative synchronous fluorescence spectroscopy as two analytical methods for the simultaneous determination of rabeprazole sodium and domperidone after derivatization with 4-chloro-7-nitrobenzofurazan.

Two simple, sensitive, rapid, economic and validated methods, namely reversed phase liquid chromatography (method Ι) and third derivative synchronous fluorescence spectroscopy (method ΙΙ) have been developed for the simultaneous determination of rabeprazole sodium and domperidone in their laboratory prepared mixture after derivatization with 4-Chloro-7-nitrobenzofurazan. Reversed phase chromatography was conducted using a Zorbax® SB-Phenyl column (250.0 mm × 4.6 mm id) combined with a guard column at ambient temperature with fluorimetric detection at 540 nm after excitation at 483 nm. A mobile phase composed of a mixture of distilled water with methanol and acetonitrile in a ratio of 50:20:30 adjusted pH to 4 has been used at a flow rate of 1 mL/min. Sharp well resolved peaks were obtained for domperidone and rabeprazole sodium with retention times of 5.5 and 6.4 min respectively. While in method ΙΙ, the third-derivative spectra were estimated at 507 and 436 nm for rabeprazole sodium and domperidone respectively. Linearity ranges for rabeprazole sodium and domperidone respectively in both methods were found to be 0.15-2.0 and 0.1-1.5 µg/mL. The proposed methods were successfully applied for the analysis of the two compounds in their binary mixtures, and laboratory prepared tablets. The obtained results were favorably compared with those obtained by the comparison method. Furthermore, detailed validation procedure was also conducted.

Normal and polar-organic-phase high-performance liquid chromatographic enantioresolution of omeprazole, rabeprazole, lansoprazole and pantoprazole using monochloro-methylated cellulose-based chiral stationary phase and determination of dexrabeprazole.

Enantioresolution of four anti-ulcer drugs (chiral sulfoxides), namely, omeprazole, rabeprazole, lansoprazole and pantoprazole, was carried out by high-performance liquid chromatography using a polysaccharide-based chiral stationary phase consisting of monochloromethylated cellulose (Lux cellulose-2) under normal and polar-organic-phase conditions with ultraviolet detection at 285 nm. The method was validated for linearity, accuracy, precision, robustness and limit of detection. The optimized enantioresolution method was compared for both the elution modes. The optimized method was further utilized to check the enantiomeric purity of dexrabeprazole.