Preparation and Evaluation of Clarithromycin Taste-Masking Dry Suspension Using Hot Melt Extrusion Based on Solid Dispersion Technology.

Clarithromycin (CLA) is the preferred drug for treating respiratory infections in pediatric patients, but it has the drawbacks of extreme bitterness and poor water solubility. The purpose of this study was to improve solubility and mask the extreme bitterness of CLA. We use Hot Melt Extrusion (HME) to convert CLA and Eudragit® E100 into Solid Dispersion (SD). Differential scanning calorimetry (DSC) and Powder X-ray diffraction (PXRD) were used to identify the crystalline form of the prepared SDs, which showed that the crystalline CLA was converted to an amorphous form. At the same time, an increase in dissolution rate was observed, which is one of the properties of SD. The results showed that the prepared SD significantly increased the dissolution rate of crystalline CLA. Subsequently, the SD of CLA was prepared into a dry suspension with excellent suspending properties and a taste-masking effect. The bitterness bubble chart and taste radar chart showed that the SD achieved the bitter taste masking of CLA. Principal components analysis (PCA) of the data generated by the electronic tongue showed that the bitter taste of CLA was significantly suppressed using the polymer Eudragit® E100. Subsequently, a dry suspension was prepared from the SD of CLA. In conclusion, this work illustrated the importance of HME for preparing amorphous SD of CLA, which can solve the problems of bitterness-masking and poor solubility. It is also significant for the development of compliant pediatric formulations.

Dynamics of an aqueous suspension of short hyaluronic acid chains near a DPPC bilayer.

The synergy between hyaluronic acid (HA) and lipid molecules plays a crucial role in synovial fluids, cell coatings, etc. Diseased cells in cancer and arthritis show changes in HA concentration and chain size, impacting the viscoelastic and mechanical properties of the cells. Although the solution behavior of HA is known in experiments, a molecular-level understanding of the role of HA in the dynamics at the interface of HA-water and the cellular boundary is lacking. Here, we perform atomistic molecular dynamics simulation of short HA chains in an explicit water solvent in the presence of a DPPC bilayer, relevant in pathological cases. We identify a stable interface between HA-water and the bilayer where the water molecules are in contact with the bilayer and the HA chains are located away without any direct contact. Both translation and rotation of the interfacial waters in contact with the lipid bilayer and translation of the HA chains exhibit subdiffusive behavior. The diffusive behavior sets in slightly away from the bilayer, where the diffusion coefficients of water and HA decrease monotonically with increase in HA concentration. On the contrary, the dependence on HA chain size is only marginal due to enhanced chain flexibility as their size increases.

Modelling the effects of charge on antibiotic diffusion and adsorption in liquid crystalline virus suspensions.

We develop a microscopic model of antibiotic diffusion in virus suspensions in a liquid crystalline state. We then approximate this with an effective homogenised model that is more amenable to analytical investigation, to understand the effect of charge on the antibiotic tolerance. We show that liquid crystalline virus suspensions slow down antibiotics significantly, and that electric charge strongly contributes to this by influencing the effective diameter and adsorptive capacity of the liquid crystalline viruses so that charged antibiotics diffuse much slower than neutral ones; this can be directly and efficiently derived from the homogenised model and is in good agreement with experiments in microbiology. Charge is also found to affect the relationship between antibiotic diffusion and viral packing density in a nontrivial way. The results elucidate the effect of charge on antibiotic tolerance in liquid crystalline biofilms in a manner that is straightforwardly extendable to other soft matter systems.

Design of Experiments-Driven Optimization of Spray Drying for Amorphous Clotrimazole Nanosuspension.

This study employed a Quality by Design (QbD) approach to spray dry amorphousclotrimazole nanosuspension (CLT-NS) consisting of Soluplus® and microcrystallinecellulose. Using the Box-Behnken Design, a systematic evaluation was conducted toanalyze the impact of inlet temperature, % aspiration, and feed rate on the criticalquality attributes (CQAs) of the clotrimazole spray-dried nanosuspension (CLT-SDNS). In this study, regression analysis and ANOVA were employed to detect significantfactors and interactions, enabling the development of a predictive model for the spraydrying process. Following optimization, the CLT-SD-NS underwent analysis using Xraypowder diffraction (XRPD), Fourier transform infrared spectroscopy (FTIR), Dynamic Scanning Calorimetry (DSC), and in vitro dissolution studies. The resultsshowed significant variables, including inlet temperature, feed rate, and aspiration rate,affecting yield, redispersibility index (RDI), and moisture content of the final product. The models created for critical quality attributes (CQAs) showed statistical significanceat a p-value of 0.05. XRPD and DSC confirmed the amorphous state of CLT in theCLT-SD-NS, and FTIR indicated no interactions between CLT and excipients. In vitrodissolution studies showed improved dissolution rates for the CLT-SD-NS (3.12-foldincrease in DI water and 5.88-fold increase at pH 7.2 dissolution media), attributed torapidly redispersing nanosized amorphous CLT particles. The well-designed studyutilizing the Design of Experiments (DoE) methodology.

Nanosuspension-Loaded Dissolving Microneedle Patches for Enhanced Transdermal Delivery of a Highly Lipophilic Cannabidiol.

Purpose: Transdermal Drug Delivery System (TDDS) offers a promising alternative for delivering poorly soluble drugs, challenged by the stratum corneum's barrier effect, which restricts the pool of drug candidates suitable for TDDS. This study aims to establish a delivery platform specifically for highly lipophilic drugs requiring high doses (log P > 5, dose > 10 mg/kg/d), to improve their intradermal delivery and enhance solubility. Methods: Cannabidiol (CBD, log P = 5.91) served as the model drug. A CBD nanosuspension (CBD-NS) was prepared using a bottom-up method. The particle size, polydispersity index (PDI), zeta potential, and concentration of the CBD-NS were characterized. Subsequently, CBD-NS was incorporated into dissolving microneedles (DMNs) through a one-step manufacturing process. The intradermal dissolution abilities, physicochemical properties, mechanical strength, insertion depth, and release behavior of the DMNs were evaluated. Sprague-Dawley (SD) rats were utilized to assess the efficacy of the DMN patch in treating knee synovitis and to analyze its skin permeation kinetics and pharmacokinetic performance. Results: The CBD-NS, stabilized with Tween 80, exhibited a particle size of 166.83 ± 3.33 nm, a PDI of 0.21 ± 0.07, and a concentration of 46.11 ± 0.52 mg/mL. The DMN loaded with CBD-NS demonstrated favorable intradermal dissolution and mechanical properties. It effectively increased the delivery of CBD into the skin, extended the action's duration in vivo, and enhanced bioavailability. CBD-NS DMN exhibited superior therapeutic efficacy and safety in a rat model of knee synovitis, significantly inhibiting TNF-α and IL-1ß compared with the methotrexate subcutaneous injection method. Conclusion: NS technology effectively enhances the solubility of the poorly soluble drug CBD, while DMN facilitates penetration, extends the duration of action in vivo, and improves bioavailability. Furthermore, CBD has shown promising therapeutic outcomes in treating knee synovitis. This innovative drug delivery system is expected to offer a more efficient solution for the administration of highly lipophilic drugs akin to CBD, thereby facilitating high-dose administration.

Effect of high acyl gellan gum and pH on the structural and foaming properties of heated whey protein suspensions.

Effects of association between high-acyl gellan gum and whey protein on heat-induced aggregation and foaming properties of aggregates were assessed in aqueous suspensions. Associative complexes were identified by turbidity and colloidal charge below pH 6, and a balance of charge in the complexes was achieved at pH 5 with a 5:1 protein:polysaccharide ratio. As gellan gum content increased, size of aggregates formed by heating at pH 5 decreased (>1000 nm to 200-300 nm). Microscopy showed polysaccharide chains adhered to spherical aggregates at pH 5 and 6. Gellan gum added to protein before heating did not increase foam volume yet doubled foam half-life at pH 5 when used at a 2:1 protein-to-polysaccharide ratio. Microscopy showed that protein aggregates with attached gellan gum were present in drained foams. These findings indicate that gellan gum improves foam stability of heated whey protein at pH 5 by reducing aggregate size and adhering to aggregates.

Viscosity of Suspensions of Strongly Bonded Spherical Particles of Nickel-Manganese-Cobalt Mixed Oxides (NMC) in Molten Poly(Ethylene Carbonate) for Batteries.

Ionically conductive polymers highly filled with active materials, such as metal oxides are increasingly studied for their potential use in all solid-state batteries. They offer the desirable processing ease of polymers for mass production despite interfacial issues that remain to be solved. In this study, it is shown that spherical particles of transition metal oxides can be introduced in co-polymers of alkene carbonate and ethylene oxide at loading close to the maximum packing fraction, without imparting the processability in the melt of the material. In particular, the viscosity does not show any yield stress and the increase of viscosity shows that the intrinsic viscosity of the filler does not match with the usual 2.5 value in the limit of the Einstein's equation. Conversely, rheological data show that the value is rather close to unity consistently with theoretical arguments that predicted that this scaling factor should be unity when particle rotation is precluded. In the present case, this behavior is attributed to strong bonding between polymer and filler that is proved by electronic microscopy and by dynamical mechanical spectroscopy showing a relaxation due to bound polymer.

Tracking colloidal silica particles to evaluate their dispersion and interactions in concentrated suspensions under shear force applications.

This study aimed to characterize interactions within colloidal silica particles in their concentrated suspensions, using rheo-confocal measurements and imaging, followed by image analysis. We studied the effect of shear rate (0-500 s-1) and solution pH (6, 10) on the dispersion degree of colloidal silica particles via the determination and comparison of interparticle distances and their modeling. Images corresponding to different shear rates were analyzed to identify the coordinates of the particles. These coordinates were further analyzed to calculate the distance among the particles and then their surface-to-surface distance normalized by the particle diameter (H/D). It was found that the population of the particles per unit area of the image and H/D varied with increasing shear rate. The comparison between experimentally measured and theoretically calculated H/D identified that for some particles, the former was shorter than the latter, indicating the unexpected attractions among them against the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory. Then, the modification of previously reported equations for H/D was suggested and confirmed its validity. Assuming pair potential interaction and hydrodynamic interaction were the main non-DLVO interactions, their magnitudes were calculated and confirmed the significance of pH and shear application strength on particle dispersion/coagulation.

Electric-field induced modulation of amorphous protein aggregates: polarization, deformation, and reorientation.

Proteins in their native state are only marginally stable and tend to aggregate. However, protein misfolding and condensation are often associated with undesired processes, such as pathogenesis, or unwanted properties, such as reduced biological activity, immunogenicity, or uncontrolled materials properties. Therefore, controlling protein aggregation is very important, but still a major challenge in various fields, including medicine, pharmacology, food processing, and materials science. Here, flexible, amorphous, micron-sized protein aggregates composed of lysozyme molecules reduced by dithiothreitol are used as a model system. The preformed amorphous protein aggregates are exposed to a weak alternating current electric field. Their field response is followed in situ by time-resolved polarized optical microscopy, revealing field-induced deformation, reorientation and enhanced polarization as well as the disintegration of large clusters of aggregates. Small-angle dynamic light scattering was applied to probe the collective microscopic dynamics of amorphous aggregate suspensions. Field-enhanced local oscillations of the intensity auto-correlation function are observed and related to two distinguishable elastic moduli. Our results validate the prospects of electric fields for controlling protein aggregation processes.

Comparison of the influence of cationic polysaccharides on the stability properties of montmorillonite suspensions in the presence of sodium dodecyl sulphate.

The mixtures of cationic cellulose (CC) or cationic guar gum (CGG) with the anionic sodium dodecyl sulfate surfactant (SDS) were used as stabilizers for the aqueous suspensions of montmorillonite (Mt). The stabilization processes and the stabilization mechanism were investigated using the UV-VIS. The obtained results show that both polysaccharides can be used as stabilizers of the water suspensions of montmorillonite due to the effective adsorption of CC and CGG with or without SDS on the Mt. surface. To obtain complete information on the studied systems, the additional measurements of the surface tension, zeta potential, FT-IR, XRD and SEM were made. The results prove that the intermolecular complexes formed between the polysaccharides and SDS can adsorb on the Mt. surface, change the structure of the electrical double layer and the stability properties of the studied suspensions.

Linear and nonlinear oscillatory rheology of chemically pretreated and non-pretreated cellulose nanofiber suspensions.

Linear and nonlinear rheological properties of cellulose nanofiber (CNF) suspensions were measured under small and large amplitude oscillatory shear (SAOS and LAOS) flow. Four different CNFs were produced, two by only mechanical disintegration and two with chemical pretreatments. Linear viscoelastic properties distinguished chemically treated CNFs from two untreated fibers via a different scaling exponent of the elastic modulus. However, different mechanical fibrillation degree was not characterized via linear viscoelastic properties. In contrast, nonlinear viscoelastic properties reflected both effects of chemical pretreatments and mechanical fibrillation. More fibrillated CNFs exhibited nonlinear rheological phenomena at larger deformations. In addition, chemically treated CNFs exhibited greater network stiffness and higher network recovery rates due to the presence of charged functional groups on the fiber surfaces. A material-property co-plot showed that network stiffness and recovery rate were in a trade-off relationship.

Rhamnolipids as Effective Green Agents in the Destabilisation of Dolomite Suspension.

In this paper, we describe an application of mono- and dirhamnolipid homologue mixtures of a biosurfactant as a green agent for destabilisation of a dolomite suspension. Properties of the biosurfactant solution were characterised using surface tension and aggregate measurements to prove aggregation of rhamnolipids at concentrations much lower than the critical micelle concentration. Based on this information, the adsorption process of biosurfactant molecules on the surface of the carbonate mineral dolomite was investigated, and the adsorption mechanism was proposed. The stability of the dolomite suspension after rhamnolipid adsorption was investigated by turbidimetry. The critical concentration of rhamnolipid at which destabilisation of the suspension occurred most effectively was found to be 50 mg·dm-3. By analysing backscattering profiles, solid-phase migration velocities were calculated. With different amounts of biomolecules, this parameter can be modified from 6.66 to 20.29 mm·h-1. Our study indicates that the dolomite suspension is destabilised by hydrophobic coagulation, which was proved by examining the wetting angle of the mineral surface using the captive bubble technique. The relatively low amount of biosurfactant used to destabilise the system indicates the potential application of this technology for water treatment or modification of the hydrophobicity of mineral surfaces in mineral engineering.

Active Controlled and Tunable Coacervation Using Side-Chain Functional α-Helical Homopolypeptides.

We report the development of new side-chain amino acid-functionalized α-helical homopolypeptides that reversibly form coacervate phases in aqueous media. The designed multifunctional nature of the side-chains was found to provide a means to actively control coacervation via mild, biomimetic redox chemistry as well as allow response to physiologically relevant environmental changes in pH, temperature, and counterions. These homopolypeptides were found to possess properties that mimic many of those observed in natural coacervate forming intrinsically disordered proteins. Despite ordered α-helical conformations that are thought to disfavor coacervation, molecular dynamics simulations of a polypeptide model revealed a high degree of side-chain conformational disorder and hydration around the ordered backbone, which may explain the ability of these polypeptides to form coacervates. Overall, the modular design, uniform nature, and ordered chain conformations of these polypeptides were found to provide a well-defined platform for deconvolution of molecular elements that influence biopolymer coacervation and tuning of coacervate properties for downstream applications.

Quality assessment of selected co-trimoxazole suspension brands marketed in Nairobi County, Kenya.

INTRODUCTION: Quality of medicines in both developed and developing countries is sometimes compromised due to infiltration of counterfeit, substandard or degraded medicines into the markets. It is a public health concern as poor quality medicines endanger public health where patients are exposed to chemical toxins and/or sub-therapeutic doses. This could lead to reduced treatment efficacy and promote development of drug resistance. Co-trimoxazole, a fixed dose combination of sulfamethoxazole and trimethoprim, is a broad spectrum for bacterial diseases and is also used as a prophylaxis for opportunistic infections in HIV infected individuals. This study evaluated quality of selected co-trimoxazole suspension brands marketed in Nairobi County, Kenya. METHODS: A total of 106 samples were collected, categorized into 15 brands and evaluated for active pharmaceutical ingredient content (API) and pH following United States Pharmacopeia. Assay for API was conducted using High Performance Liquid Chromatography. Results were compared with pharmacopeia references. Visual examination of labels and confirmation of retention status of the brands with Pharmacy and Poisons Board retention register was carried out. RESULTS: The samples were primarily of local origin (86.7%). On October 23, 2019, retention status of six of the fifteen brands documented were no longer listed in the Pharmacy and Poisons Board retention register. Of the 106 samples tested 70.6% and 86.8% were compliant with United States Pharmacopeia (USP) specifications for pH and API respectively while 84.0% adhered to packaging and labelling requirements. CONCLUSION: This study has demonstrated that majority of co-trimoxazole suspensions tested were compliant with USP requirements. Additionally, it has provided evidence of poor quality co-trimoxazole medicines that could compromise treatment of infectious diseases in children. This emphasizes the need for regular quality assurance tests to ensure only quality medicines are in the market.

In vitro and in vivo Evaluation of Ibuprofen Nanosuspensions for Enhanced Oral Bioavailability.

INTRODUCTION: The objectives were to prepare, characterize, and evaluate different ibuprofen (IBU) nanosuspensions. METHODS: The nanosuspensions produced by ultrahomogenization were compared with a marketed IBU suspension for particle size, in vitro dissolution, and in vivo absorption. Five groups of rabbits were orally administered with 25 mg/kg of IBU nanosuspension, nanoparticles, unhomogenized suspension, marketed product, and untreated suspension. A sixth group received 5 mg/kg IBU intravenously. Blood samples obtained were analyzed by chromatography. RESULTS: The nanosuspensions showed significant decrease in particle size. Polyvinylpyrrolidone (PP) K30 profoundly increased aqueous solubility of IBU. Addition of Tween 80 (TW), in equal amount as PP (IBU:PP:TW, 1:2:2 w/w), resulted in much smaller particle size and better dissolution rate. The Cmax values achieved were 14.8 ± 1.64, 11.1 ± 1.37, 9.01 ± 0.761, 7.03 ± 1.38, and 3.23 ± 1.03 µg/mL, and the tmax values were 36 ± 8.2, 39 ± 8.2, 100 ± 17.3, 112 ± 15, and 105 ± 17 min for the nanosuspension, nanoparticle, unhomogenized suspension, marketed IBU suspension, and untreated IBU suspension in water, respectively. Bioavailability of the different formulations relative to the marketed suspension was found to be in the following sequence: nanosuspension > unhomogenized suspension > nanoparticles > untreated IBU suspension. CONCLUSION: IBU/PP/TW nanosuspension showed enhanced in vitro and in vivo performance as compared to the marketed product. Nanosuspensions prepared by the ultrahigh-pressure homogenization technique can be used as a good formulation strategy to enhance the rate and extent of absorption of poorly soluble drugs.

Preparation of Cellulose/Laponite Composite Particles and Their Enhanced Electrorheological Responses.

Cellulose, as a natural polymer with an abundant source, has been widely used in many fields including the electric field responsive medium that we are interested in. In this work, cellulose micron particles were applied as an electrorheological (ER) material. Because of the low ER effect of the raw cellulose, a composite particle of cellulose and Laponite was prepared via a dissolution-regeneration process. Scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) were used to observe the morphologies and structures of the composite particles, which were different from pristine cellulose and Laponite, respectively. The ER performances of raw cellulose and the prepared composite were measured by an Anton Paar rotational rheometer. It was found that the ER properties of the composite were more superior to those of raw cellulose due to the flake-like shapes of the composite particles with rough surface. Moreover, the sedimentation stability of composite improves drastically, which means better suspension stability.

Phase separation in mixed suspensions of bacteria and nonadsorbing polymers.

The shapes of bacteria can vary widely; they may, for instance, be spherical, rod-like, string-like, or curved. In general, bacilli are highly anisotropic. For research and (bio)technological purposes, it can be useful to concentrate bacteria, which is possible by adding nonadsorbing polymers. The induced phase separation originates from a polymer-mediated depletion interaction, first understood by Asakura and Oosawa. Here, it is shown that free volume theory (FVT) can semi-quantitatively describe the phase transitions observed when adding sodium polystyrene sulfonate polymers to E. coli bacteria [Schwarz-Linek et al., Soft Matter 6, 4540 (2010)] at high ionic strength. The E. coli bacteria are described as short, hard spherocylinders. FVT predicts that the phase transitions of the mixtures result from a fluid-ABC crystal solid phase coexistence of a hard spherocylinder-polymer mixture.

Impact of Formulation Parameters on In Vitro Release from Long-Acting Injectable Suspensions.

The development of long-acting injectable (LAI) suspension products has increased in recent years. A better understanding of the relationship between the physicochemical properties of these products and their in vitro as well as in vivo performance is expected to further facilitate their development and regulatory review. Using Depo-SubQ Provera 104® as the reference listed drug (RLD), four qualitatively and quantitatively (Q1/Q2) equivalent LAI suspensions with different formulation properties were prepared. Two recrystallization methods (solvent evaporation and antisolvent) were utilized to obtain active pharmaceutical ingredient (API) with different properties and solid-state characterization was performed. In addition, two different sources of the major excipient were used to prepare the Q1/Q2 equivalent suspensions. Physiochemical characterization and in vitro release testing of the prepared Q1/Q2 equivalent suspension formulations and the RLD were conducted. In vitro drug release was dependent not only on the particle size, the morphology, and the crystallinity of the API but also on the residual solvent in the API. The excipient source also affected the drug release rates.

Centrifugal ultrafiltration preconcentration for studying the colloidal phase of a uranium-containing soil suspension.

The objective of this work was to explore centrifugal ultrafiltration (UF) to separate and / or preconcentrate natural colloidal particles for their characterization. A soil suspension obtained by batch leaching was used as a laboratory reference sample. It was preconcentrated with concentration factors (CF) varying from 10 to 450. The dimensional analysis of the colloidal phase was carried out by Asymmetric Flow Field-Flow Fractionation (AF4)-multidetection. The colloidal masses were estimated by mass balance of the initial suspension, its concentrates and filtrates. The size-dependent distribution (expressed in gyration radius) and total colloidal mass (especially recovery), as well as chemical composition and concentration (including species partitioning between dissolved and colloidal phases) were determined to assess the effects of UF preconcentration on colloidal particles. The gyration radius of the colloidal particles recovered in these concentrated suspensions ranged from about 20 nm to over 150 nm. Neither de-agglomeration nor agglomeration was observed. However, only (64 ± 4) % (CF = 10) of the colloidal particles initially in the soil suspension were found in the recovered concentrated suspensions, and this percentage decreased as CF increased. The filter membrane trapped all other particles, mainly the larger ones. Whatever the CF, the centrifugal UF did not appear to change the dissolved-colloidal partitioning of certain species (Al, organic carbon); whereas it led to an enrichment of the colloidal phase for others (Fe, U). The enrichment rate was specific to each species (15% for Fe; 100% for U). By fitting the observed trends (i.e. conservation, depletion or enrichment of the colloidal phase in the concentrate) as a function of CF, the colloidal concentrations (total and species) were assessed without bias. This methodology offers a new perspective for determining physicochemical speciation in natural waters, with a methodology applicable for environmental survey or site remediation studies.

Development of Novel Bead Milling Technology with Less Metal Contamination by pH Optimization of the Suspension Medium.

To develop novel contamination-less bead milling technology without impairing grinding efficiency, we investigated the effect of the formulation properties on the grinding efficiency and the metal contamination generated during the grinding process. Among the various formulations tested, the combination of polyvinylpyrrolidone and sodium dodecyl sulfate was found to be suitable for efficiently pulverizing phenytoin. However, this stabilization system included a relatively strong acid, which raised the concern of possible corrosion of the zirconia beads. An evaluation of the process clearly demonstrated that acidic pH promoted bead dissolution, suggesting that this could be suppressed by controlling the pH of the suspension. Among the various pH values tested, the metal contamination generated during the grinding process could be significantly reduced in the optimized pH range without significant differences in the particle size of the phenytoin suspension after pulverization. In addition, the contamination reduction by pH optimization in the presence of physical contact among the beads was approximately 10-times larger than that without bead contact, suggesting that pH optimization could suppress not only bead dissolution but also the wear caused by bead collisions during the grinding process. These findings show that pH optimization is a simple but effective approach to reducing metal contamination during the grinding process.