Biofiltration of toluene in the presence of ethyl acetate or n-hexane: Performance and microbial community.

This study describes the operation of two independent parallel laboratory-scale biotrickling filters (BTFs) to degrade different types of binary volatile organic compound (VOC) mixtures. Comparison experiments were conducted to evaluate the effects of two typical VOCs, i.e., ethyl acetate (a hydrophilic VOC) and n-hexane (a hydrophobic VOC) on the removal performance of toluene (a moderately hydrophobic VOC) in BTFs ''A" and ''B", respectively. Experiments were carried out by stabilizing the toluene concentration at 1.64 g m-3 and varying the concentrations of gas-phase ethyl acetate (0.85-2.8 g m-3) and n-hexane (0.85-2.8 g m-3) at an empty bed residence time (EBRT) of 30 s. In the presence of ethyl acetate (850 ± 55 mg m-3), toluene exhibited the highest removal efficiency (95.4 ± 2.2%) in BTF "A". However, the removal rate of toluene varied from 48.1 ± 6.9% to 70.1 ± 6.8% when 850 ± 123 mg m-3 to 2800 ± 136 mg m-3 of n-hexane was introduced into BTF "B". The high-throughput sequencing data revealed that the genera Pseudomonas and Comamonadaceae_unclassified are the core microorganisms responsible for the degradation of toluene. The intensity of the inhibitory or synergistic effects on toluene removal was influenced by the type and concentration of the introduced VOC, as well as the number and activity of the genera Pseudomonas and Comamonadaceae_unclassified. It provides insights into the interaction between binary VOCs during biofiltration from a microscopic perspective.

The impact of ozone treatment on the removal effectiveness of various refractory compounds in wastewater from petroleum refineries.

Large volumes of wastewater are generated during petroleum refining processes. Petroleum refinery wastewater (PRW) can contain highly toxic compounds that can harm the environment. These toxic compounds can be a challenge in biological treatment technologies due to the effects of these compounds on microorganisms. These challenges can be overcome by using ozone (O3) as a standalone or as a pretreatment to the biological treatment. Ozone was used in this study to degrade the organic pollutants in the heavily contaminated PRW from a refinery in Mpumalanga province of South Africa. The objective was achieved by treating the raw PRW using ozone at different ozone treatment times (15, 30, 45, and 60 min) at a fixed ozone concentration of 3.53 mg/dm3. The ozone treatment was carried out in a 2-liter custom-designed plexiglass cylindrical reactor. Ozone was generated from an Eco-Lab-24 corona discharge ozone generator using clean, dry air from the Afrox air cylinder as feed. The chemical oxygen demand, gas chromatograph characterization, and pH analysis were performed on the pretreated and post-treated PRW samples to ascertain the impact of the ozone treatment. The ozone treatment was effective in reducing the benzene, toluene, ethylbenzene, and xylenes (BTEX) compounds in the PRW. The 60-min ozone treatment of different BTEX pollutants in the PRW resulted in the following percentage reduction: benzene 95%, toluene 77%, m + p-xylene 70%, ethylbenzene 69%, and o-xylene 65%. This study has shown the success of using ozone in reducing the toxic BTEX compounds in a heavily contaminated PRW.

Performance on adsorption of toluene by ionic liquid-modified AC in high-humidity exhaust gas.

Volatile organic compounds (VOCs) frequently pose a threat to the biosphere, impacting ecosystems, flora, fauna, and the surrounding environment. Industrial emissions of VOCs often include the presence of water vapor, which, in turn, diminishes the adsorption capacity and efficacy of adsorbents. This occurs due to the competitive adsorption of water vapor, which competes with target pollutants for adsorption sites on the adsorbent material. In this study, hydrophobic activated carbons (BMIMPF6-AC (L), BMIMPF6-AC (g), and BMIMPF6-AC-H) were successfully prepared using 1-butyl-3-methylimidazolium hexafluorophosphate (BMIMPF6) to adsorb toluene under humidity environment. The adsorption performance and mechanism of the resulting ionic liquid-modified activated carbon for toluene in a high-humidity environment were evaluated to explore the potential application of ionic liquids as hydrophobic modifiers. The results indicated that BMIMPF6-AC-H exhibited superior hydrophobicity. The toluene adsorption capacity of BMIMPF6-AC-H was 1.53 times higher than that of original activated carbon, while the adsorption capacity for water vapor was only 37.30% of it at 27 °C and 77% RH. The Y-N model well-fitted the dynamic adsorption experiments. To elucidate the microscopic mechanism of hydrophobic modification, the Independent Gradient Model (IGM) method was employed to characterize the intermolecular interactions between BMIMPF6 and toluene. Overall, this study introduces a new modifier for hydrophobic modification of activated carbon, which could enhance the efficiency of activated carbon in treating industrial VOCs.

Biofiltration of n-butyl acetate with three packing material mixtures, with and without biochar.

Two cost-effective packing materials were used for n-butyl acetate removal in lab-scale biofilters, namely waste spruce root wood chips and biochar obtained as a byproduct from a wood gasifier. Three biofilters packed with spruce root wood chips: without biochar (SRWC), a similar one with 10% of biochar (SRWC-B) and that with 10% of biochar impregnated with a nitrogen fertilizer (SRWC-IB) showed similar yet differing maximum elimination capacities of 206 ± 27, 275 ± 21 and 294 ± 20 g m-3 h-1, respectively, enabling high pollutant removal efficiency (>95% at moderate loads) and stable performance. The original biochar adsorption capacity was high (208 ± 6 mgtoluene g-1), but near 70% of it was lost after a 300-day biofilter operation. By contrast, the exposed impregnated biochar drastically increased its adsorption capacity in 300 days (149 ± 7 vs. 17 ± 5 mgtoluene g-1). Colony forming unit (CFU) and microscopic analyses revealed significant packing material colonization by microorganisms and grazing fauna in all three biofilters with an acceptable pressure drop, up to 1020 Pa m-1, at the end of biofilter operation. Despite a higher price (14 vs. 123 €m-3), the application of the best performing SRWC-IB packing can reduce the total investment costs by 9% due to biofilter volume reduction.

Liquid- liquid (Cyclohexanone: Cyclohexanol) separation using augmented tight nanofiltration membrane: A sustainable approach.

Organic solvent nanofiltration (OSN) is an incipient technology in the field of organic liquid-liquid separation. The incomplete separations and complexity involved in these, forces many organic liquids to be released as effluents and the adverse effects of these on environment is enormous and irreparable. The work prominences on the complete separation of industrially significant cyclohexanone: cyclohexanol (keto-alcohol oil) and heptane: toluene mixtures. The separations of these above-mentioned organic liquid mixtures were carried out using the fabricated Lewis acid modified graphitic carbon nitride (Cu2O@g-C3N4) incorporated polyvinylidene difluoride (PVDF) composite membranes. These fabricated membranes showed a separation factor of 18.16 and flux of 1.62 Lm-2h-1 for cyclohexanone: cyclohexanol mixture and separation of heptane and toluene mixture (with heptane flux of 1.52 Lm-2h-1) showed a separation factor of 9.9. The selectivity and productivity are based on the polarity and size of the organic liquids. The role of Cu2O@g-C3N4 is influencing the pore size distribution, increased divergence from solubility parameters, polarity, solvent uptake and porosity of the composite membranes. The developed composite membranes are thus envisioned to be apt for a wide range of liquid-liquid separations due to its implicit nature.

Ni-FeOx synergy induced by metal-support interaction on Ni-impregnated incineration bottom ash for effective tar reforming.

The incineration bottom ash (IBA) was impregnated with nickel to catalyze toluene (tar surrogate) steam reforming. A toluene conversion of >80 % was achieved at 800℃ without activity decay in a 100-h test for 15 %Ni/IBA. An activation stage was observed for Ni/IBA catalysts in the initial 50 âˆ¼ 400 min under different reaction conditions. A series of experiments and characterizations were performed to explore the possible mechanisms for the activation. It was found that the iron species in IBA gradually migrated to the catalyst surface and formed a Ni-FeOx complex owing to the metal-support interaction. The synergy of Ni-FeOx played an important role in improving the activity of Ni/IBA due to the enhanced lattice oxygen activity. Additionally, Ni/IBA catalysts showed a much lower coke deposition rate than Ni/Al2O3 (1.12 vs. 3.45 mg-C/gcat∙h) because of the variable states of FeOx and the abundant basic sites caused by the alkali and alkaline earth metals contained in IBA.

Rapid determination of hippuric acid as an exposure biomarker of toluene using a colorimetric assay and comparison with high-performance liquid chromatography.

Occupational exposure to toluene is associated with health risks that require reliable monitoring methods. Hippuric acid (HA), a urinary metabolite of toluene, serves as a valuable biomarker for such exposure. Colorimetric methods for the quantitative determination of HA have gained prominence due to their simplicity, cost-effectiveness, and suitability for field application. In the present study, a simple colorimetric technique was optimized for the determination of HA in the urine sample, and compared with a usual HPLC technique. The central composite design (CCD) was applied to examine the effective parameters on the colorimetric determination of HA. The calibration curve for HA was established within the concentration range of 6 to 100 mg L-1 with R2 = 0.97. The detection limit (LOD) and quantification limit (LOQ) were determined to be 1.8 mg L-1 and 6 mg L-1 respectively. The relative standard deviation (RSD%) was less than 5%, and the recovery% (R%) was 90.5-100.1. The overall results showed good agreement between the colorimetric and HPLC results. There was a significant relationship between the results obtained from HPLC and colorimetric methods especially for higher concentration levels of HA (≥ 500 mg/g creatinine). In conclusion, our optimized colorimetric method is a simple, cost-effective, and rapid method for determination of HA in occupational exposure, which is comparable with the HPLC technique.

Exposure to benzene, toluene, ethylbenzene, and xylene (BTEX) at Nigeria's petrol stations: a review of current status, challenges and future directions.

Introduction: In Nigeria, because of increasing population, urbanization, industrialization, and auto-mobilization, petrol is the most everyday non-edible commodity, and it is the leading petroleum product traded at the proliferating Nigeria's petrol stations (NPSs). However, because of inadequate occupational health and safety (OHS) regulatory measures, working at NPSs exposes petrol station workers (PSWs) to a large amount of hazardous benzene, toluene, ethylbenzene, and xylene (BTEX) compounds. Methods: Studies on BTEX exposures among Nigerian PSWs are scarce. Thus, constraints in quantifying the health risks of BTEX limit stakeholders' ability to design practical risk assessment and risk control strategies. This paper reviews studies on the OHS of Nigerian PSWs at the NPSs. Results: Although knowledge, attitude, and practices on OHS in NPSs vary from one Nigeria's study setting to another, generally, safety practices, awareness about hazards and personal protective equipment (PPE), and the use of PPE among PSWs fell below expectations. Additionally, air quality at NPSs was poor, with a high content of BTEX and levels of carbon monoxide, hydrogen sulfide, particulate matter, and formaldehyde higher than the World Health Organization guideline limits. Discussion: Currently, regulatory bodies' effectiveness and accountability in safeguarding OHS at NPSs leave much to be desired. Understanding the OHS of NPSs would inform future initiatives, policies, and regulations that would promote the health and safety of workers at NPSs. However, further studies need to be conducted to describe the vulnerability of PSWs and other Nigerians who are occupationally exposed to BTEX pollution. More importantly, controlling air pollution from hazardous air pollutants like BTEX is an essential component of OHS and integral to attaining the Sustainable Development Goals (SDG) 3, 7, and 11.

Boosting Photothermocatalytic Oxidation of Toluene Over Pt/N-TiO2: The Gear Effect of Light and Heat.

Photothermal catalysis is extremely promising for the removal of various indoor pollutants owing to its photothermal synergistic effect, while the low light utilization efficiency and unclear catalytic synergistic mechanism hinder its practical applications. Here, nitrogen atoms are introduced, and Pt nanoparticles are loaded on TiO2 to construct Pt/N-TiO2-H2, which exhibits 3.5-fold higher toluene conversion rate than the pure TiO2. Compared to both photocatalytic and thermocatalytic processes, Pt/N-TiO2-H2 exhibited remarkable performance and stability in the photothermocatalytic oxidation of toluene, achieving 98.4% conversion and 98.3% CO2 yield under a light intensity of 260 mW cm-2. Furthermore, Pt/N-TiO2-H2 demonstrated potential practical applicability in the photothermocatalytic elimination of various indoor volatile organic compounds. The synergistic effect occurs as thermocatalysis accelerates the accumulation of carboxylate species and the degradation of aldehyde species, while photocatalysis promotes the generation of aldehyde species and the consumption of carboxylate species. This ultimately enhances the photothermocatalytic process. The photothermal synergistic effect involves the specific conversion of intermediates through the interplay of light and heat, providing novel insights for the design of photothermocatalytic materials and the understanding of photothermal mechanisms.

Anaerobic treatment of groundwater co-contaminated by toluene and copper in a single chamber bioelectrochemical system.

Addressing the simultaneous removal of multiple coexisting groundwater contaminants poses a significant challenge, primarily because of their different physicochemical properties. Indeed, different chemical compounds may necessitate establishing distinct, and sometimes conflicting, (bio)degradation and/or removal pathways. In this work, we investigated the concomitant anaerobic treatment of toluene and copper in a single-chamber bioelectrochemical cell with a potential difference of 1 V applied between the anode and the cathode. As a result, the electric current generated by the bioelectrocatalytic oxidation of toluene at the anode caused the abiotic reduction and precipitation of copper at the cathode, until the complete removal of both contaminants was achieved. Open circuit potential (OCP) experiments confirmed that the removal of copper and toluene was primarily associated with polarization. Analogously, abiotic experiments, at an applied potential of 1 V, confirmed that neither toluene was oxidized nor copper was reduced in the absence of microbial activity. At the end of each experiment, both electrodes were characterized by means of a comprehensive suite of chemical and microbiological analyses, evidencing a highly selected microbial community competent in the biodegradation of toluene in the anodic biofilm, and a uniform electrodeposition of spherical Cu2O nanoparticles over the cathode surface.

Biomonitoring of volatile organic compounds and organophosphorus flame retardands in commercial aircrews after "fume and smell events".

Health risks to humans after "fume and smell events", short-term incidents on aircrafts that are accompanied by unpleasant odour or visible smoke, remain a subject of controversy. We assessed exposure to volatile organic compounds (VOC) and organophosphorus compounds (OPC) by biomonitoring in 375 aircrew members after self-reported "fume and smell events" and in 88 persons of the general population. A total of 20 parameters were analysed in blood and urine by gas chromatography and mass spectrometry. Median levels of acetone in blood and urine and 2-propanol in blood were elevated in aircrews compared to controls (p < 0.0001). Additionally, elevated peak exposures, best estimated by the 95th percentiles, were observed in aircrews for n-heptane and n-octane in blood, and acetone, 2,5-hexanedione and o-cresol in urine. Only the maximum observed levels of 2,5-hexandione in urine (768 µg/L) and toluene in blood (77 µg/L) in aircrew members were higher than the current biological exposure indices (BEI® levels) (500 and 20 µg/L, respectively) of the American Conference of Governmental Industrial Hygienists (US-ACGIH) for workers occupationally exposed to n-hexane and toluene, two well-accepted human neurotoxicants. Low-level exposures to n-hexane and toluene could be also observed in controls. The majority of OPC parameters in urine, including those of neurotoxic ortho-isomers of tricresylphosphate, were below the limit of quantitation in both aircrews and controls. Our comparative VOC and OPC analyses in biological samples of a large number of aircrew members and controls suggest that exposures are similar in both groups and generally low.

Association between urinary BTEX metabolites and dyslexic odds among school-aged children.

Benzene, toluene, ethylbenzene, and xylene (BTEX) are ubiquitous in the environment, and all of them can cause neurotoxicity. However, the association between BTEX exposure and dyslexia, a disorder with language network-related regions in left hemisphere affected, remains unclear. We aimed to assess the relationship between BTEX exposure and dyslexic odds among school-aged children. A case-control study, including 355 dyslexics and 390 controls from three cities in China, was conducted. Six BTEX metabolites were measured in their urine samples. Logistic regression model was used to explore the association between the BTEX metabolites and the dyslexic odds. Urinary trans,trans-muconic acid (MU: a metabolite of benzene) was significantly associated with an increased dyslexic odds [odds ratio (OR) = 1.23, 95% confidence interval (CI): 1.01, 1.50], and the adjusted OR of the dyslexic odds in the third tertile was 1.72 (95% CI: 1.06, 2.77) compared to that in the lowest tertile regarding urinary MU concentration. Furthermore, the association between urinary MU level and the dyslexic odds was more pronounced among children from low-income families based on stratified analyses. Urinary metabolite levels of toluene, ethylbenzene, and xylene were not found to be associated with the dyslexic odds. In summary, elevated MU concentrations may be associated with an increased dyslexic odds. We should take measures to reduce MU related exposure among children, particularly those with low family income.

Modulating the Electronic Structures of Pt on Pt/TiO2 Catalyst for Boosting Toluene Oxidation.

Surface hydroxyl groups commonly exist on the catalyst and present a significant role in the catalytic reaction. Considering the lack of systematical researches on the effect of the surface hydroxyl group on reactant molecule activation, the PtOx/TiO2 and PtOx-y(OH)y/TiO2 catalysts were constructed and studied for a comprehensive understanding of the roles of the surface hydroxyl group in the oxidation of volatiles organic compounds. The PtOx/TiO2 formed by a simple treatment with nitric acid presented greatly enhanced activity for toluene oxidation in which the turnover frequency of toluene oxidation on PtOx/TiO2 was around 14 times as high as that on PtOx-y(OH)y/TiO2. Experimental and theoretical results indicated that adsorption/activation of toluene and reactivity of oxygen atom on the catalyst determined the toluene oxidation on the catalyst. The removal of surface hydroxyl groups on PtOx promoted strong electronic coupling of the Pt 5d orbital in PtOx and C 2p orbital in toluene, facilitating the electron transfers from toluene to PtOx and subsequently the adsorption/activation of toluene. Additionally, the weak Pt-O bond promoted the activation of surface lattice oxygen, accelerating the deep oxidation of activated toluene. This study clarifies the inhibiting effect of surface hydroxyl groups on PtOx in toluene oxidation, providing a further understanding of hydrocarbon oxidation.

Evaluating workplace protection factors (WPFs) of different firefighter PPE interface control measures for select volatile organic compounds (VOCs).

Structural firefighters are exposed to a complex set of contaminants and combustion byproducts, including volatile organic compounds (VOCs). Additionally, recent studies have found structural firefighters' skin may be exposed to multiple chemical compounds via permeation or penetration of chemical byproducts through or around personal protective equipment (PPE). This mannequin-based study evaluated the effectiveness of four different PPE conditions with varying contamination control measures (incorporating PPE interface design features and particulate blocking materials) to protect against ingress of several VOCs in a smoke exposure chamber. We also investigated the effectiveness of long-sleeve base layer clothing to provide additional protection against skin contamination. Outside gear air concentrations were measured from within the smoke exposure chamber at the breathing zone, abdomen, and thigh heights. Personal air concentrations were collected from mannequins under PPE at the same general heights and under the base layer at abdomen and thigh heights. Sampled contaminants included benzene, toluene, styrene, and naphthalene. Results suggest that VOCs can readily penetrate the ensembles. Workplace protection factors (WPFs) were near one for benzene and toluene and increased with increasing molecular weight of the contaminants. WPFs were generally lower under hoods and jackets compared to under pants. For all PPE conditions, the pants appeared to provide the greatest overall protection against ingress of VOCs, but this may be due in part to the lower air concentrations toward the floor (and cuffs of pants) relative to the thigh-height outside gear concentrations used in calculating the WPFs. Providing added interface control measures and adding particulate-blocking materials appeared to provide a protective benefit against less-volatile chemicals, like naphthalene and styrene.

Risk assessment of Benzene, Toluene, Ethyl benzene, and Xylene (BTEX) in the atmospheric air around the world: A review.

Volatile organic compounds, such as BTEX, have been the subject of numerous debates due to their detrimental effects on the environment and human health. Human beings have had a significant role in the emergence of this situation. Even though US EPA, WHO, and other health-related organizations have set standard limits as unhazardous levels, it has been observed that within or even below these limits, constant exposure to these toxic chemicals results in negative consequences as well. According to these facts, various studies have been carried out all over the world - 160 of which are collected within this review article, so that experts and governors may come up with effective solutions to manage and control these toxic chemicals. The outcome of this study will serve the society to evaluate and handle the risks of being exposed to BTEX. In this review article, the attempt was to collect the most accessible studies relevant to risk assessment of BTEX in the atmosphere, and for the article to contain least bias, it was reviewed and re-evaluated by all authors, who are from different institutions and backgrounds, so that the insights of the article remain unbiased. There may be some limitations to consistency or precision in some points due to the original sources, however the attempt was to minimize them as much as possible.

Metagenomics revealing biomolecular insights into the enhanced toluene removal and electricity generation in PANI@CNT bioanode.

Microbial fuel cells (MFCs) have significant potential for environmental remediation and energy recycling directly from refractory aromatic hydrocarbons. To boost the capacities of toluene removal and the electricity production in MFCs, this study constructed a polyaniline@carbon nanotube (PANI@CNT) bioanode with a three-dimensional framework structure. Compared with the control bioanode based on graphite sheet, the PANI@CNT bioanode increased the output voltage and toluene degradation kinetics by 2.27-fold and 1.40-fold to 0.399 V and 0.60 h-1, respectively. Metagenomic analysis revealed that the PANI@CNT bioanode promoted the selective enrichment of Pseudomonas, with the dual functions of degrading toluene and generating exogenous electrons. Additionally, compelling genomic evidence elucidating the relationship between functional genes and microorganisms was found. It was interesting that the genes derived from Pseudomonas related to extracellular electron transfer, tricarboxylic acid cycle, and toluene degradation were upregulated due to the existence of PANI@CNT. This study provided biomolecular insights into key genes and related microorganisms that effectively facilitated the organic pollutant degradation and energy recovery in MFCs, offering a novel alternative for high-performance bioanode.

Synchronous removal of gaseous toluene and benzene and degradation process shifts in microbial fuel cell-biotrickling filter system.

Illustrating the biodegradation processes of multi-component volatile organic compounds (VOCs) will expedite the implication of biotechnology in purifying industrial exhaust. Here, performance shifts of microbial fuel cell and biotrickling filter combined system (MFC-BTF) are investigated for removing single and dual components of toluene and benzene. Synchronous removal of toluene (95 %) and benzene (97 %) are achieved by MFC-BTF accompanied with the output current of 0.41 mA. Elevated content of extracellular polymeric substance facilitates the mass transfer of benzene with the presence of toluene. Strains of Bacteroidota, Proteobacteria and Chloroflexi contribute to the removal of dual components VOCs. Empty bed reaction time and the VOCs concentration are the important factors influencing their dissolution in the system. The biodegradation of toluene and benzene proceeds with 2-hydroxymuconic semialdehyde and o-hydroxybenzoic acid as the main intermediates. These results provide a comprehensive understanding of multi-component VOCs removal by MFC-BTF and guide the system design, optimization, and scale-up.

Endotracheal enucleation and para-toluenesulfonamide injection for adenoid cystic carcinoma in the upper trachea: A novel therapeutic approach.

We present a case of an adenoid cystic carcinoma (ACC) located in the upper trachea, which resulted in significant airway blockage, that was unsuitable for surgical removal due to concerns about functional impairment. Instead, endotracheal enucleation via rigid bronchoscopy was performed initially, followed by the injection of a novel tumor ablation agent known as para-toluenesulfonamide (PTS). We detail the dosing regimen, effectiveness evaluation, and post-treatment follow-up. The study highlights the potential of PTS injection as a viable alternative treatment option for patients with ACC who cannot undergo surgical resection and feasibility of lipiodol to monitor treatment effect. This research adds to the existing knowledge on ACC treatment and provides new therapeutic possibilities for patients with tracheal ACC.

Prefeeding of Clarias gariepinus with Spirulina platensis counteracts petroleum hydrocarbons-induced hepato- and nephrotoxicity.

Petroleum aromatic hydrocarbons are considered one of the most dangerous aquatic pollutants due to their widespread across water bodies, persistence, and extension to the food chain. To our knowledge, there hasn't been any research investigating the hepatorenoprotective effects of Spirulina platensis (SP) against toxicity induced by these environmental toxicants in fish. Thus, we decided to explore its potential safeguarding against benzene and toluene exposure in adult Clarias gariepinus. To achieve this objective, fish were divided into five groups (60 per group; 20 per replicate). The first group served as a control. The second and third groups were intoxicated with benzene and toluene at doses of 0.762 and 26.614 ng/L, respectively for 15 days. The fourth and fifth groups (SP + benzene and SP + toluene, respectively) were challenged with benzene and toluene as previously mentioned following dietary inclusion of SP at a dose of 5 g/kg diet for 30 days. The marked increase in liver metabolizing enzymes, glucose, total protein, albumin, globulin, albumin/globulin ratio, and creatinine confirmed the hepato- and nephrotoxic impacts of benzene and toluene. These outcomes were coupled with cytopathological affections and excessive collagen deposition. The incorporation of SP in ration formulation, on the contrary, restored the previously mentioned toxicological profile due to its antioxidant and cytoprotective attributes. Regardless of SP intervention, the renal tissues still displayed histo-architectural lesions, because of insufficient dose and timeframe. Additional research will be required to identify the ideal SP remediation regimen.

Catalytic oxidation of toluene by manganese oxides: Effect of K+ doping on oxygen vacancy.

Alkali metal potassium was beneficial to the electronic regulation and structural stability of transition metal oxides. Herein, K ions were introduced into manganese oxides by different methods to improve the degradation efficiency of toluene. The results of activity experiments indicated that KMnO4-HT (HT: Hydrothermal method) exhibited outstanding low-temperature catalytic activity, and 90% conversion of toluene can be achieved at 243°C, which was 41°C and 43°C lower than that of KNO3-HT and Mn-HT, respectively. The largest specific surface area was observed on KMnO4-HT, facilitating the adsorption of toluene. The formation of cryptomelane structure over KMnO4-HT could contribute to higher content of Mn3+ and lattice oxygen (Olatt), excellent low-temperature reducibility, and high oxygen mobility, which could increase the catalytic performance. Furthermore, two distinct degradation pathways were inferred. Pathway Ⅰ (KMnO4-HT): toluene → benzyl → benzoic acid → carbonate → CO2 and H2O; Pathway ⅠⅠ (Mn-HT): toluene → benzyl alcohol → benzoic acid → phenol → maleic anhydride → CO2 and H2O. Fewer intermediates were detected on KMnO4-HT, indicating its stronger oxidation capacity of toluene, which was originated from the doping of K+ and the interaction between KOMn. More intermediates were observed on Mn-HT, which can be attributed to the weaker oxidation ability of pure Mn. The results indicated that the doping of K+ can improve the catalytic oxidation capacity of toluene, resulting in promoted degradation of intermediates during the oxidation of toluene.