Changes of cerebral functional connectivity induced by foot reflexology in a RCT.

Non-Pharmacological Interventions (NPIs) are increasingly being introduced into healthcare, but their mechanisms are unclear. In this study, 30 healthy participants received foot reflexology (FR) and sham massage, and went through a resting-state functional magnetic resonance imaging (rs-fMRI) to evaluate NPIs effect on brain. Rs-fMRI revealed an effect of both NPIs on functional connectivity with changes occurring in the default-mode network, the sensorimotor network and a Neural Network Correlates of Pain (NNCP-a newly discovered network showing great robustness). Even if no differences were found between FR and SM, this study allowed to report brain biomarkers of well-being as well as the safety of NPIs. In further research, it could be relevant to study it in patients to look for a true reflexology induced-effect dependent of patient reported outcomes. Overall, these findings enrich the understanding of the neural correlates of well-being experienced with NPIs and provided insight into the basis of the mechanisms of NPIs.

Polarization Induced Electro-Functionalization of Pore Walls: A Contactless Technology.

This review summarizes recent advances in micro- and nanopore technologies with a focus on the functionalization of pores using a promising method named contactless electro-functionalization (CLEF). CLEF enables the localized grafting of electroactive entities onto the inner wall of a micro- or nano-sized pore in a solid-state silicon/silicon oxide membrane. A voltage or electrical current applied across the pore induces the surface functionalization by electroactive entities exclusively on the inside pore wall, which is a significant improvement over existing methods. CLEF's mechanism is based on the polarization of a sandwich-like silicon/silicon oxide membrane, creating electronic pathways between the core silicon and the electrolyte. Correlation between numerical simulations and experiments have validated this hypothesis. CLEF-induced micro- and nanopores functionalized with antibodies or oligonucleotides were successfully used for the detection and identification of cells and are promising sensitive biosensors. This technology could soon be successfully applied to planar configurations of pores, such as restrictions in microfluidic channels.

A review on mechanical considerations for chronically-implanted neural probes.

This review intends to present a comprehensive analysis of the mechanical considerations for chronically-implanted neural probes. Failure of neural electrical recordings or stimulation over time has shown to arise from foreign body reaction and device material stability. It seems that devices that match most closely with the mechanical properties of the brain would be more likely to reduce the mechanical stress at the probe/tissue interface, thus improving body acceptance. The use of low Young's modulus polymers instead of hard substrates is one way to enhance this mechanical mimetism, though compliance can be achieved through a variety of means. The reduction of probe width and thickness in comparison to a designated length, the use of soft hydrogel coatings and the release in device tethering to the skull, can also improve device compliance. Paradoxically, the more compliant the device, the more likely it will fail during the insertion process in the brain. Strategies have multiplied this past decade to offer partial or temporary stiffness to the device to overcome this buckling effect. A detailed description of the probe insertion mechanisms is provided to analyze potential sources of implantation failure and the need for a mechanically-enhancing structure. This leads us to present an overview of the strategies that have been put in place over the last ten years to overcome buckling issues. Particularly, great emphasis is put on bioresorbable polymers and their assessment for neural applications. Finally, a discussion is provided on some of the key features for the design of mechanically-reliable, polymer-based next generation of chronic neuroprosthetic devices.

Functionalization of optical nanotip arrays with an electrochemical microcantilever for multiplexed DNA detection.

Optical nanotip arrays fabricated on etched fiber bundles were functionalized with DNA spots. Such unconventional substrates (3D and non-planar) are difficult to pattern with standard microfabrication techniques but, using an electrochemical cantilever, up to 400 spots were electrodeposited on the nanostructured optical surface in 5 min. This approach allows each spot to be addressed individually and multiplexed fluorescence detection is demonstrated. Finally, remote fluorescence detection was performed by imaging through the optical fiber bundle itself after hybridisation with the complementary sequence.

Polarization-induced local pore-wall functionalization for biosensing: from micropore to nanopore.

The use of biological-probe-modified solid-state pores in biosensing is currently hindered by difficulties in pore-wall functionalization. The surface to be functionalized is small and difficult to target and is usually chemically similar to the bulk membrane. Herein, we demonstrate the contactless electrofunctionalization (CLEF) approach and its mechanism. This technique enables the one-step local functionalization of the single pore wall fabricated in a silica-covered silicon membrane. CLEF is induced by polarization of the pore membrane in an electric field and requires a sandwich-like composition and a conducting or semiconducting core for the pore membrane. The defects in the silica layer of the micropore wall enable the creation of an electric pathway through the silica layer, which allows electrochemical reactions to take place locally on the pore wall. The pore diameter is not a limiting factor for local wall modification using CLEF. Nanopores with a diameter of 200 nm fabricated in a silicon membrane and covered with native silica layer have been successfully functionalized with this method, and localized pore-wall modification was obtained. Furthermore, through proof-of-concept experiments using ODN-modified nanopores, we show that functionalized nanopores are suitable for translocation-based biosensing.

Opto-electrochemical nanosensor array for remote DNA detection.

A high-density array of opto-electrochemical nanosensors is presented for remote DNA detection. It was fabricated by chemical etching of a coherent optical fibre bundle to produce a nanotip array. The surface of the etched bundle was sputter-coated with a thin ITO layer which was eventually insulated by an electrophoretic paint. The fabrication steps produced a high-density array of electrochemical nanosensors which retains the optical fibre bundle architecture and its imaging properties. A DNA probe was then immobilized on the nanosensor array surface in a polypyrrole film by electropolymerisation. After hybridisation with the complementary sequence, detection of the strepavidin-R-phycoerythrin label is performed by fluorescence imaging through the optical fibre bundle itself. Control experiments and regeneration steps have also been successfully demonstrated on this nanostructured opto-electrochemical platform.

Versatile functionalization of nanoelectrodes by oligonucleotides via pyrrole electrochemistry.

Surface modification at the nanometer scale is a challenge for the future of molecular electronics. In particular, the precise anchoring and electrical addressing of biological scaffolds such as complex DNA nanonetworks is of importance for generating bio-directed assemblies of nano-objects for nanocircuit purposes. Herein, we consider the individual modification of nanoelectrodes with different oligonucleotide sequences by an electrochemically driven co-polymerization process of pyrrole and modified oligonucleotide sequences bearing pyrrole monomers. We demonstrate that this one-step technique presents the advantages of simplicity, localization of surface modification, mechanical, biological and chemical stability of the coatings, and high lateral resolution.

Contactless electrofunctionalization of a single pore.

Customized pores are smart components that find challenging applications in a variety of fields including purification membranes and biosensing systems. The incorporation of recognition probes within pores is therefore a challenge, due to the technical difficulty of delimiting the area functionalized and obtaining the localized, specific chemical modification of pore walls. An innovative approach, named contactless electrofunctionalization (CLEF), is presented to overcome this problem. CLEF allows easy, one-step modification of the inner surface of a pore etched in a dielectric membrane. The pore wall is coated under the influence of an electric field created by the application of a voltage between two electrodes, located near but not in contact with the pore openings. This specific localization of the deposited material within the pore is extremely rapid. Coatings were reliably and reproducibly obtained using polypyrrole co-polymers bearing oligonucleotides, demonstrating that this technology has a promising future in the design of biosensors. Moreover, the versatility of this process allows the deposition of various electroactive entities such as iridium oxide and therefore indicates a strong potential for diverse applications involving porous materials.