RESUMO
Few studies aiming to develop a glue with an underwater reusable adhesive property have been reported because combining the two properties of reusable adhesion and underwater adhesion into a single glue formulation is a challenging issue. Herein, preparation of a simple mixture of poly(vinyl alcohol) (PVA) and a well-known phenolic compound, namely, tannic acid (TA), results in an underwater glue exhibiting reusable adhesion. We named the adhesive VATA (PVA + TA). Using VATA, two stainless steel objects (0.77 kg each) are able to be instantly attached. In addition to the high adhesive strength, surface-applied VATA in water retains its adhesive capability even after 24 h. In contrast, cyanoacrylate applied under the same water condition rapidly loses its adhesive power. Another advantage is that VATA's adhesion is reusable. Bonded objects can be forcibly detached, and then the detached ones can be reattached by the residual VATA. VATA maintains nearly 100% of its initial adhesive force, even after 10 repetitions of attach-detach cycles. VATA bonds various materials ranging from metals and polymers to ceramics. Particularly, we first attempt to test the toxicity of the underwater adhesives using an invertebrate nematode, Caenorhabditis elegans and gold fish (vertebrate) due to potential release to the environment.
Assuntos
Adesivos/química , Álcool de Polivinil/química , Taninos/química , Adesividade , Adesivos/toxicidade , Animais , Caenorhabditis elegans/efeitos dos fármacos , Carpa Dourada , Teste de Materiais , Álcool de Polivinil/toxicidade , Estresse Mecânico , Taninos/toxicidade , Resistência à Tração , Água/químicaRESUMO
We have studied the deposition of polymer micelles formed from poly(styrene)-block-poly(2-vinylpyridine) (PS-PVPH+) from room-temperature aqueous solutions at pH 1 onto a hydrophilic Si/SiO2 surface with a relief pattern 100 nm deep with variable widths. It has been found that the micelle density is substantially higher and the ordering of the micelles is improved for micelles that adsorb in the 100 nm depressions in the width range of ca. 500-5000 nm. We ascribe these effects to capillary forces that pull the aqueous solution into the canyons where the micelles can be trapped. While the ordering of the micelles can be substantial, they do not form a perfect hexagonal crystal. If the surface is chemically modified by a Au coating, the micelle-surface interaction is strengthened and the degree of ordering is diminished. These results demonstrate that a combination of graphoepitaxy and processing conditions (speed of substrate withdrawal or evaporation of solvent) can be used to make fairly ordered polymer micelle arrays over a space of (at least) several millimeters.
RESUMO
The deposition of PS-PVPH+ polymer micelles from a pH 1 aqueous solution onto Si wafers has been studied using a simple dip-coating technique. It has been found that the rate of evaporation of the solvent and the rate of withdrawal have a considerable influence on the density and ordering of the adsorbed micelles. The highest density and degree of ordering (as judged by the 2D pair correlation function) is achieved when solvent evaporation dominates the deposition process, but a fairly homogeneous distribution of polymer micelles can be achieved over a distance of at least 3-4 mm by controlling the solvent evaporation rate and the rate of substrate withdrawal. We did not observe any significant effect of added KCl (up to 0.1 M) during the deposition process or soaking in 1 M KCl after deposition. The attachment of these micelles is quite robust, as they cannot be washed off in pH 1 water (with or without KCl) without significant mechanical assistance. However, we did find that the micelles are rather easily caused to dewet and partially aggregate under the influence of 65 degrees C water vapor.