Compositional texture engineering for highly stable wide-bandgap perovskite solar cells.

The development of highly stable and efficient wide-bandgap (WBG) perovskite solar cells (PSCs) based on bromine-iodine (Br-I) mixed-halide perovskite (with Br greater than 20%) is critical to create tandem solar cells. However, issues with Br-I phase segregation under solar cell operational conditions (such as light and heat) limit the device voltage and operational stability. This challenge is often exacerbated by the ready defect formation associated with the rapid crystallization of Br-rich perovskite chemistry with antisolvent processes. We combined the rapid Br crystallization with a gentle gas-quench method to prepare highly textured columnar 1.75-electron volt Br-I mixed WBG perovskite films with reduced defect density. With this approach, we obtained 1.75-electron volt WBG PSCs with greater than 20% power conversion efficiency, approximately 1.33-volt open-circuit voltage (Voc), and excellent operational stability (less than 5% degradation over 1100 hours of operation under 1.2 sun at 65°C). When further integrated with 1.25-electron volt narrow-bandgap PSC, we obtained a 27.1% efficient, all-perovskite, two-terminal tandem device with a high Voc of 2.2 volts.

A performance comparison between GaInP-on-Si and GaAs-on-Si 3-terminal tandem solar cells.

The pursuit of ever-higher solar cell efficiencies has focused heavily on multijunction technologies. In tandem cells, subcells are typically either contacted via two terminals (2T) or four terminals (4T). Simulations show that the less-common three-terminal (3T) design may be comparable to 4T tandem cells in its compatibility with a range of materials, operating conditions, and methods for subcell integration, yet the 3T design circumvents shading losses of the 4T intermediate conductive layers. This study analyzes the performance of two superstrate 3T III-V-on-Si (III-V//Si) tandem cells: One has slightly greater current contribution from the Si bottom cell (GaInP//Si) and the other has substantially greater current contribution from the GaAs top cell (GaAs//Si). Our results show that both tandem cells exhibit the same efficiency (21.3%), thereby demonstrating that the third terminal allows for flexibility in the selection of the top cell material, similar to the 4T design.

Chemical and mechanical interfacial degradation in bifacial glass/glass and glass/transparent backsheet photovoltaic modules.

Glass/glass (G/G) photovoltaic modules are quickly rising in popularity, but the durability of modern G/G packaging has not yet been established. In this work, we examine the interfacial degradation modes in G/G and glass/transparent backsheet modules under damp heat (DH) with and without system bias voltage, comparing emerging polyolefin elastomer (POE) and industry-standard poly(ethylene-co-vinyl acetate) (EVA) encapsulants. We investigate the transport of ionic species at cell/encapsulant interfaces, demonstrating that POE limits both sodium and silver ion migration compared with EVA. Changes to the chemical structures of the encapsulants at the cell/encapsulant interfaces demonstrate that both POE and EVA are more susceptible to degradation in modules with a transparent backsheet than in the G/G configuration. Adhesion testing reveals that POE and EVA have comparable critical debond energies after the DH exposures regardless of system bias polarity. The results of this study indicate that the interfacial degradation mechanisms of G/G appear to be similar to those of conventional glass/backsheet modules. For emerging materials, our results demonstrate that POE offers advantages over EVA but that transparent backsheets may accelerate encapsulant degradation due to increased moisture ingress when compared with the G/G structure.

Publisher Correction: Gallium arsenide solar cells grown at rates exceeding 300 µm h-1 by hydride vapor phase epitaxy.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

Pain Management Efficacy Study Between Continuous and Single-Administration Bupivacaine Following Lumbar Spinal Fusion.

Poorly managed postoperative pain decreases patient satisfaction, impedes early patient mobilization, lengthens inpatient hospital stay, and increases healthcare costs. Multimodal analgesia with local anesthetics is considered most effective for postoperative pain management. This study compared patients undergoing lumbar fusion who received plain bupivacaine from May 2011 until August 2012 with those who received liposomal bupivacaine from September 2012 until May 2013. The aim was to determine which preparation reduced postoperative opioid use the most. All lumbar spinal fusion surgeries in the periods indicated were included in the study. Ninety-three patient charts were reviewed: 47 for the plain bupivacaine group and 46 for the liposomal bupivacaine group. The study found no statistical difference between liposomal and plain bupivacaine in providing postoperative pain control from lumbar fusion surgery. Liposomal bupivacaine is as effective as plain bupivacaine for postoperative pain control after lumbar fusion. However, a continuous infusion system carries substantial inherent drawbacks: need for training and setup, pump cost, risk of infection at the insertion site, or catheter migration. Therefore, liposomal bupivacaine becomes the logical and attractive choice to manage postoperative pain following lumbar fusion.

Gallium arsenide solar cells grown at rates exceeding 300 µm h-1 by hydride vapor phase epitaxy.

We report gallium arsenide (GaAs) growth rates exceeding 300 µm h-1 using dynamic hydride vapor phase epitaxy. We achieved these rates by maximizing the gallium to gallium monochloride conversion efficiency, and by utilizing a mass-transport-limited growth regime with fast kinetics. We also demonstrate gallium indium phosphide growth at rates exceeding 200 µm h-1 using similar growth conditions. We grew GaAs solar cell devices by incorporating the high growth rate of GaAs and evaluated its material quality at these high rates. Solar cell growth rates ranged from 35 to 309 µm h-1 with open circuit voltages ranging from 1.04 to 1.07 V. The best devices exceeded 25% efficiency under the AM1.5 G solar spectrum. The high open-circuit voltages indicate that high material quality can be maintained at these extremely high growth rates. These results have strong implications toward lowering the deposition cost of III-V materials potentially enabling the deposition of high efficiency devices in mere seconds.

Numerical evidence of fluctuating stripes in the normal state of high-Tc cuprate superconductors.

Upon doping, Mott insulators often exhibit symmetry breaking where charge carriers and their spins organize into patterns known as stripes. For high-transition temperature cuprate superconductors, stripes are widely suspected to exist in a fluctuating form. We used numerically exact determinant quantum Monte Carlo calculations to demonstrate dynamical stripe correlations in the three-band Hubbard model, which represents the local electronic structure of the copper-oxygen plane. Our results, which are robust to varying parameters, cluster size, and boundary conditions, support the interpretation of experimental observations such as the hourglass magnetic dispersion and the Yamada plot of incommensurability versus doping in terms of the physics of fluctuating stripes. These findings provide a different perspective on the intertwined orders emerging from the cuprates' normal state.

Realization of a Hole-Doped Mott Insulator on a Triangular Silicon Lattice.

The physics of doped Mott insulators is at the heart of some of the most exotic physical phenomena in materials research including insulator-metal transitions, colossal magnetoresistance, and high-temperature superconductivity in layered perovskite compounds. Advances in this field would greatly benefit from the availability of new material systems with a similar richness of physical phenomena but with fewer chemical and structural complications in comparison to oxides. Using scanning tunneling microscopy and spectroscopy, we show that such a system can be realized on a silicon platform. The adsorption of one-third monolayer of Sn atoms on a Si(111) surface produces a triangular surface lattice with half filled dangling bond orbitals. Modulation hole doping of these dangling bonds unveils clear hallmarks of Mott physics, such as spectral weight transfer and the formation of quasiparticle states at the Fermi level, well-defined Fermi contour segments, and a sharp singularity in the density of states. These observations are remarkably similar to those made in complex oxide materials, including high-temperature superconductors, but highly extraordinary within the realm of conventional sp-bonded semiconductor materials. It suggests that exotic quantum matter phases can be realized and engineered on silicon-based materials platforms.

Pain Management Efficacy Study Between Continuous and Single-Administration Bupivacaine Following Lumbar Spinal Fusion.

Poorly managed postoperative pain decreases patient satisfaction, impedes early patient mobilization, lengthens inpatient hospital stay, and increases healthcare costs. Multimodal analgesia with local anesthetics is considered most effective for postoperative pain management. This study compared patients undergoing lumbar fusion who received plain bupivacaine from May 2011 until August 2012 with those who received liposomal bupivacaine from September 2012 until May 2013. The aim was to determine which preparation reduced postoperative opioid use the most. All lumbar spinal fusion surgeries in the periods indicated were included in the study. Ninety-three patient charts were reviewed: 47 for the plain bupivacaine group and 46 for the liposomal bupivacaine group. The study found no statistical difference between liposomal and plain bupivacaine in providing postoperative pain control from lumbar fusion surgery. Liposomal bupivacaine is as effective as plain bupivacaine for postoperative pain control after lumbar fusion. However, a continuous infusion system carries substantial inherent drawbacks: need for training and setup, pump cost, risk of infection at the insertion site, or catheter migration. Therefore, liposomal bupivacaine becomes the logical and attractive choice to manage postoperative pain following lumbar fusion.

Formation and Dissociation of Sperm Bundles in Monotremes.

Because monotremes are the earliest offshoot of the mammalian lineage, the platypus and short-beaked echidna were studied as model animals to assess the origin and biological significance of adaptations considered unique to therian mammals: epididymal sperm maturation and subsequent capacitation. We show that spermatozoa from both species assemble into bundles of approximately 100 cells during passage through the epididymis and that an epididymal protein-secreted protein, acidic, cysteine-rich (osteonectin; SPARC)-is involved in bundle formation. The bundles persisted during incubation in vitro for at least 1 h under conditions that capacitate therian spermatozoa, and then underwent a time-dependent dissociation to release spermatozoa capable of fertilization. Only after this dissociation could the spermatozoa bind to the perivitelline membrane of a hen's egg, display an altered form of motility reminiscent of hyperactivation, and be induced to undergo an acrosome reaction. It is concluded that the development of sperm bundles in the monotreme epididymis mandates that they require a time-dependent process to be capable of fertilizing an ovum. However, because this functional end point was achieved without overt changes in protein tyrosine phosphorylation (a hallmark of capacitation in therians), it is concluded that the process in monotremes is distinctly different from capacitation in therian mammals.

Orbital-selective Mott phases of a one-dimensional three-orbital Hubbard model studied using computational techniques.

A recently introduced one-dimensional three-orbital Hubbard model displays orbital-selective Mott phases with exotic spin arrangements such as spin block states [J. Rincón et al., Phys. Rev. Lett. 112, 106405 (2014)PRLTAO0031-900710.1103/PhysRevLett.112.106405]. In this publication we show that the constrained-path quantum Monte Carlo (CPQMC) technique can accurately reproduce the phase diagram of this multiorbital one-dimensional model, paving the way to future CPQMC studies in systems with more challenging geometries, such as ladders and planes. The success of this approach relies on using the Hartree-Fock technique to prepare the trial states needed in CPQMC. We also study a simplified version of the model where the pair-hopping term is neglected and the Hund coupling is restricted to its Ising component. The corresponding phase diagrams are shown to be only mildly affected by the absence of these technically difficult-to-implement terms. This is confirmed by additional density matrix renormalization group and determinant quantum Monte Carlo calculations carried out for the same simplified model, with the latter displaying only mild fermion sign problems. We conclude that these methods are able to capture quantitatively the rich physics of the several orbital-selective Mott phases (OSMP) displayed by this model, thus enabling computational studies of the OSMP regime in higher dimensions, beyond static or dynamic mean-field approximations.

Electron-lattice interactions strongly renormalize the charge-transfer energy in the spin-chain cuprate Li2CuO2.

Strongly correlated insulators are broadly divided into two classes: Mott-Hubbard insulators, where the insulating gap is driven by the Coulomb repulsion U on the transition-metal cation, and charge-transfer insulators, where the gap is driven by the charge-transfer energy Δ between the cation and the ligand anions. The relative magnitudes of U and Δ determine which class a material belongs to, and subsequently the nature of its low-energy excitations. These energy scales are typically understood through the local chemistry of the active ions. Here we show that the situation is more complex in the low-dimensional charge-transfer insulator Li2CuO2, where Δ has a large non-electronic component. Combining resonant inelastic X-ray scattering with detailed modelling, we determine how the elementary lattice, charge, spin and orbital excitations are entangled in this material. This results in a large lattice-driven renormalization of Δ, which significantly reshapes the fundamental electronic properties of Li2CuO2.

Direct observation of a Fermi liquid-like normal state in an iron-pnictide superconductor.

There are two prerequisites for understanding high-temperature (high-Tc) superconductivity: identifying the pairing interaction and obtaining a correct description of the normal state from which superconductivity emerges. The nature of the normal state of iron-pnictide superconductors, and the role played by correlations arising from partially screened interactions, are still under debate. Here we show that the normal state of carefully annealed electron-doped BaFe(2-x)Co(x)As2 at low temperatures has all the hallmark properties of a local Fermi liquid, with a more incoherent state emerging at elevated temperatures, an identification made possible using bulk-sensitive optical spectroscopy with high frequency and temperature resolution. The frequency dependent scattering rate extracted from the optical conductivity deviates from the expected scaling M2 (ω, T) ∝ (hω)(2) + (pπkBT)(2) with p ≈ 1.47 rather than p = 2, indicative of the presence of residual elastic resonant scattering. Excellent agreement between the experimental results and theoretical modeling allows us to extract the characteristic Fermi liquid scale T0 ≈ 1700 K. Our results show that the electron-doped iron-pnictides should be regarded as weakly correlated Fermi liquids with a weak mass enhancement resulting from residual electron-electron scattering from thermally excited quasi-particles.

The potency-insolubility conundrum in pharmaceuticals: Mechanism and solution for hepatitis C protease inhibitors.

As compounds are optimized for greater potency during pharmaceutical discovery, their aqueous solubility often decreases, making them less viable as orally-administered drugs. To investigate whether potency and insolubility share a common origin, we examined the structural and thermodynamic properties of telaprevir, a sparingly soluble inhibitor of hepatitis C virus protease. Comparison of the hydrogen bond motifs in crystalline telaprevir with those present in the protease-telaprevir complex revealed striking similarities. Additionally, the thermodynamics of telaprevir dissolution closely resembles those of protein-ligand dissociation. Together, these findings point to a common origin of potency and insolubility rooted in particular amide-amide hydrogen bond patterns. The insolubility of telaprevir is shown by computational analysis to be caused by interactions in the crystal, not unfavorable hydrophobic hydration. Accordingly, competing out the particular amide-amide hydrogen bond motifs in crystalline telaprevir with 4-hydroxybenzoic acid yielded a co-crystalline solid with excellent aqueous dissolution and oral absorption. The analysis suggests a generalizable approach for identifying drug candidate compounds that either can or cannot be rendered orally bioavailable by alteration of their crystalline solid phases, in an approach that provides a pragmatic way to attain substantial enhancements in the success rate of drug discovery and development.

Charge disproportionation without charge transfer in the rare-earth-element nickelates as a possible mechanism for the metal-insulator transition.

We study a model for the metal-insulator (M-I) transition in the rare-earth-element nickelates RNiO3, based upon a negative charge transfer energy and coupling to a rocksaltlike lattice distortion of the NiO6 octahedra. Using exact diagonalization and the Hartree-Fock approximation we demonstrate that electrons couple strongly to these distortions. For small distortions the system is metallic, with a ground state of predominantly d8L character, where L_ denotes a ligand hole. For sufficiently large distortions (δdNi-O∼0.05-0.10 Å), however, a gap opens at the Fermi energy as the system enters a periodically distorted state alternating along the three crystallographic axes, with (d8L_2)S=0(d8)S=1 character, where S is the total spin. Thus the M-I transition may be viewed as being driven by an internal volume "collapse" where the NiO6 octahedra with two ligand holes shrink around their central Ni, while the remaining octahedra expand accordingly, resulting in the (1/2, 1/2, 1/2) superstructure observed in x-ray diffraction in the insulating phase. This insulating state is an example of charge ordering achieved without any actual movement of the charge.

Effect of Molecule-Surface Reaction Mechanism on the Electronic Characteristics and Photovoltaic Performance of Molecularly Modified Si.

We report on the passivation properties of molecularly modified, oxide-free Si(111) surfaces. The reaction of 1-alcohol with the H-passivated Si(111) surface can follow two possible paths, nucleophilic substitution (SN) and radical chain reaction (RCR), depending on adsorption conditions. Moderate heating leads to the SN reaction, whereas with UV irradiation RCR dominates, with SN as a secondary path. We show that the site-sensitive SN reaction leads to better electrical passivation, as indicated by smaller surface band bending and a longer lifetime of minority carriers. However, the surface-insensitive RCR reaction leads to more dense monolayers and, therefore, to much better chemical stability, with lasting protection of the Si surface against oxidation. Thus, our study reveals an inherent dissonance between electrical and chemical passivation. Alkoxy monolayers, formed under UV irradiation, benefit, though, from both chemical and electronic passivation because under these conditions both SN and RCR occur. This is reflected in longer minority carrier lifetimes, lower reverse currents in the dark, and improved photovoltaic performance, over what is obtained if only one of the mechanisms operates. These results show how chemical kinetics and reaction paths impact electronic properties at the device level. It further suggests an approach for effective passivation of other semiconductors.

Determining the short-range spin correlations in the spin-chain Li2CuO2 and CuGeO3 compounds using resonant inelastic x-ray scattering.

We report a high-resolution resonant inelastic soft x-ray scattering study of the quantum magnetic spin-chain materials Li(2)CuO(2) and CuGeO(3). By tuning the incoming photon energy to the oxygen K edge, a strong excitation around 3.5 eV energy loss is clearly resolved for both materials. Comparing the experimental data to many-body calculations, we identify this excitation as a Zhang-Rice singlet exciton on neighboring CuO(4) plaquettes. We demonstrate that the strong temperature dependence of the inelastic scattering related to this high-energy exciton enables us to probe short-range spin correlations on the 1 meV scale with outstanding sensitivity.

Sperm chromatin in beef bulls in tropical environments.

Sperm chromatin status was assessed in 565 Zebu and Zebu crossbred beef bulls in extensive tropical environments using the sperm chromatin structure assay (SCSA). The SCSA involved exposure of sperm to acid hydrolysis for 0.5 or 5.0 minutes, followed by flow cytometry to ascertain relative amounts of double-stranded (normal) and single-stranded (denatured) DNA, which was used to generate a DNA fragmentation index (%DFI). With conventional SCSA (0.5-minute SCSA), 513 bulls (91%) had <15 %DFI, 24 bulls (4%) had 15 to 27 %DFI, and 28 bulls (5%) had >27 %DFI. In 5.0-minute SCSA, 432 bulls (76%) had <15 %DFI, 68 bulls (12%) had 15 to 27 %DFI and 65 bulls (12%) had >27 %DFI. For most bulls, the SCSA was repeatable on two to four occasions; however, because most bulls had <15 %DFI, repeatability of the SCSA will need to be determined in a larger number of bulls in the 15 to 27 %DFI and >27 %DFI categories. The %DFI was negatively correlated with several bull semen parameters and the strongest negative correlation was with normal sperm. There was a strong positive correlation between %DFI and sperm head abnormalities. Based on these findings, most Zebu beef bulls in extensive tropical environments had relatively stable sperm chromatin. Based on the apparent negative correlations with conventional semen parameters, we inferred that the SCSA measured a unique feature of sperm quality, which has also been suggested for other species. Further studies on the relationships between sperm chromatin stability and fertility are required in beef bulls before chromatin status can be used as an additional predictor of the siring capacity of individual bulls in extensive multiple-sire herds.

DNA fragmentation dynamics allows the assessment of cryptic sperm damage in human: evaluation of exposure to ionizing radiation, hyperthermia, acidic pH and nitric oxide.

Sperm DNA fragmentation (SDF) is not a static seminal parameter, since the longevity of sperm DNA decreases progressively with time following ejaculation or thawing. While the dynamics of SDF is a species-specific characteristic, in the case of humans, there is still significant variation within patients. To evaluate the suitability of the dynamic SDF assay to assess the adverse effects of agents that cause genetic damage, fresh semen samples from different donors were exposed in vitro to (1) increasing acute doses of ionizing radiation, (2) elevated temperature (41 °C and 45 °C), (3) acidic pH (pH 4) and (4) the nitric oxide (NO) donor sodium nitroprusside (SNP). Sperm DNA fragmentation was analyzed after an incubation period of chronic (24h), or acute (1h) exposure to each treatment followed by incubation at 37 °C over a period of 24h. SDF was assessed using the sperm chromatin dispersion (SCD) test. Dynamic SDF for each treatment was analyzed using Kaplan-Meier survival curves. All agents, except for ionizing radiation, accelerated SDF kinetics following chronic exposure over a 24h period. Transient exposure to NO and heat but not acidic pH increased the basal (T0) level of SDF. Despite the removal of the three toxicants, the remaining sperm following acute exposure showed a decrease in their expected DNA longevity. It is concluded that the assessment of sperm DNA fragmentation dynamics is an effective methodological approach for revealing latent damage associated with toxicants that is not initially expressed following a single initial observation of SDF.