Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 20 de 22
Filtrar
Mais filtros











Base de dados
Intervalo de ano de publicação
1.
Chem Sci ; 13(37): 11205-11214, 2022 Sep 28.
Artigo em Inglês | MEDLINE | ID: mdl-36320464

RESUMO

Copper electrodes produce several industrially relevant chemicals and fuels during the electrochemical CO2 reduction reaction (CO2RR). Knowledge about the reaction pathways can help tune the reaction selectivity toward higher-value products. To probe the uncertain role of the C2 molecule glyoxal, we electrochemically reduced it on polycrystalline Cu and quantified its liquid-phase products, namely, ethanol, ethylene glycol, and acetaldehyde. The gas phase contained hydrogen and traces of ethylene. In contrast with previous hypothesis, a one-to-one comparison with CO2RR on Cu indicates that glyoxal is neither a major intermediate in the pathway toward ethylene nor in the pathway toward ethanol. In addition, great possibilities for the selective, low-temperature production of ethylene glycol are open, as computational modelling shows that ethylene glycol and ethanol are produced on different active sites. Thus, apart from the mechanistic insight into CO2RR, this study gives new directions to facilitate the electrification of chemical processes at refineries.

3.
ACS Appl Mater Interfaces ; 14(12): 14193-14201, 2022 Mar 30.
Artigo em Inglês | MEDLINE | ID: mdl-35302346

RESUMO

Ionic liquids (ILs) are capable of tuning the kinetics of electroreduction processes by modifying a catalyst interface. In this work, a group of hydrophobic imidazolium-based ILs were immobilized on Ag foams by using a procedure known as "solid catalyst with ionic liquid layer" (SCILL). The derived electrocatalysts demonstrated altered selectivity and CO production rates for the electrochemical reduction of CO2 compared to the unmodified Ag foam. The activity change caused by the IL was dependent on the length of the N-alkyl substituent. The rate of CO production is optimized at moderate chain length and IL loadings. The observed trends are attributed to a local enrichment of CO2-based species in the proximity of the catalyst and a modification of the environment of its active sites. On the contrary, high loadings or long IL chains render the surface inaccessible and favor the hydrogen evolution reaction.

4.
ChemSusChem ; 14(23): 5245-5253, 2021 Dec 06.
Artigo em Inglês | MEDLINE | ID: mdl-34549892

RESUMO

The electrochemical conversion of biomass-based compounds to fuels and fuel precursors can aid the defossilization of the transportation sector. Herein, the electrohydrodimerization of 5-hydroxymethylfurfural (HMF) to the fuel precursor 5,5'-bis(hydroxymethyl)hydrofuroin (BHH) was investigated on different carbon electrodes. Compared to boron-doped diamond (BDD) electrodes, on glassy carbon (GC) electrodes a less negative HMF reduction onset potential and a switch in product selectivity from BHH to the electrocatalytic hydrogenation product 2,5-di(hydroxymethyl)furan (DHMF) with increasing overpotential was found. On BDD, the electrohydrodimerization was the dominant process independent of the applied potential. An increase in the initial HMF concentration led to suppression of the competing hydrogen evolution reaction and DHMF formation, resulting in higher BHH faradaic efficiencies. In contrast, BHH selectivity decreased with higher initial HMF concentration, which was attributed to increased electrochemically induced HMF degradation. Finally, it was demonstrated that even a simple graphite foil can function as an active HMF electroreduction catalyst.

5.
Rapid Commun Mass Spectrom ; 35(13): e9091, 2021 Jul 15.
Artigo em Inglês | MEDLINE | ID: mdl-33786897

RESUMO

RATIONALE: The development of an interface to analyze liquid sample streams with direct analysis in real time mass spectrometry (DART-MS) is of great interest for coupling various analytical techniques, using non-volatile salts, with MS. Therefore, we devised an enclosed ionization interface and a sample introduction system for the versatile analysis of liquid samples with DART-MS. METHODS: The sample introduction system consists of a nebulizer, a spray chamber and a transfer line, while the confined ionization interface is created by implementing a cross-shaped housing between ion source outlet and mass spectrometer inlet. Methodical studies of the effects of various setup parameters on signal intensity and peak shape were conducted, while its diverse applicability was demonstrated by coupling with high-performance liquid chromatography (HPLC) for the analysis of alcohols, organic acids and furanic compounds. RESULTS: The confinement of the ionization interface results in a robust setup design with a well-defined ionization region for focusing of the sprayed sample mist. Thereby, an increase in analyte signal intensity by three orders of magnitude and improved signal stability and reproducibility were obtained in comparison with a similar open ionization interface configuration. Additionally, the successful quantification of alcohols could be demonstrated as well as the compatibility of the setup with HPLC gradient elution. CONCLUSIONS: A versatile setup design for the analysis of liquid sample streams with DART-MS was devised for monitoring reactions or hyphenating analytics with MS. The design minimizes interferences from the laboratory surroundings as well as allows for safe handling of hazardous and toxic chemicals, which renders it suitable for a broad range of applications.

6.
ACS Appl Mater Interfaces ; 12(30): 33670-33678, 2020 Jul 29.
Artigo em Inglês | MEDLINE | ID: mdl-32623879

RESUMO

The selective electrooxidation of 2-propanol to acetone can be used in fuel cells which, when combined with the transfer hydrogenation of acetone from liquid organic hydrogen carriers, will enable the realization of hydrogen economy without using molecular hydrogen gas for storage and transportation. We study the reaction on platinum and platinum-ruthenium nanocatalysts using unique tools for the real-time characterization of reaction and dissolution products. Acetone is the primary product on all investigated catalysts, and only traces of CO2 form at high potentials. We propose that the reaction occurs on Pt-Ru ensemble sites at low potentials and on Pt-Pt sites at high potentials. Dissolution of surface ruthenium atoms leads to suppression of the process at low overpotential. The main shortcomings to be addressed for an efficient catalyst performance are (a) the narrow potential range in which the bimetallic catalyst is active, (b) the surface poisoning from adsorbed acetone, and (c) the dissolution of ruthenium.

7.
Angew Chem Int Ed Engl ; 59(41): 18095-18102, 2020 Oct 05.
Artigo em Inglês | MEDLINE | ID: mdl-32697377

RESUMO

The key to fully leveraging the potential of the electrochemical CO2 reduction reaction (CO2RR) to achieve a sustainable solar-power-based economy is the development of high-performance electrocatalysts. The development process relies heavily on trial and error methods due to poor mechanistic understanding of the reaction. Demonstrated here is that ionic liquids (ILs) can be employed as a chemical trapping agent to probe CO2RR mechanistic pathways. This method is implemented by introducing a small amount of an IL ([BMIm][NTf2 ]) to a copper foam catalyst, on which a wide range of CO2RR products, including formate, CO, alcohols, and hydrocarbons, can be produced. The IL can selectively suppress the formation of ethylene, ethanol and n-propanol while having little impact on others. Thus, reaction networks leading to various products can be disentangled. The results shed new light on the mechanistic understanding of the CO2RR, and provide guidelines for modulating the CO2RR properties. Chemical trapping using an IL adds to the toolbox to deduce the mechanistic understanding of electrocatalysis and could be applied to other reactions as well.

8.
Chemphyschem ; 20(22): 2997-3003, 2019 11 19.
Artigo em Inglês | MEDLINE | ID: mdl-31603611

RESUMO

Platinum single crystal basal planes consisting of Pt(111), Pt(100), Pt(110) and reference polycrystalline platinum Pt(poly) were subjected to various potentiodynamic and potentiostatic electrochemical treatments in 0.1 M HClO4 . Using the scanning flow cell coupled to an inductively coupled plasma mass spectrometer (SFC-ICP-MS) the transient dissolution was detected on-line. Clear trends in dissolution onset potentials and quantities emerged which can be related to the differences in the crystal plane surface structure energies and coordination. Pt(111) is observed to have a higher dissolution onset potential while the generalized trend in dissolution rates and quantities was found to be Pt(110)>P(100)≈Pt(poly)>Pt(111).

9.
Angew Chem Int Ed Engl ; 58(22): 7273-7277, 2019 May 27.
Artigo em Inglês | MEDLINE | ID: mdl-30882984

RESUMO

Methods that provide real-time information are essential to resolve transients occurring at dynamic interfaces. Now a powerful method is presented that enables the time- and potential-resolved characterization of liquid and gaseous products of electrochemical reactions shortly after their formation. To demonstrate its extraordinary potential, the electrochemical real time mass spectrometry (EC-RTMS) approach is used to determine the products of the CO2 reduction reaction (CO2 RR) during potential step or sweep experiments on pristine and in situ anodized copper. The enhanced formation of several C2+ products over C1 products is tracked directly after copper anodization, with unprecedented temporal resolution. This new technique creates exciting new opportunities for resolving processes that occur at short timescales and eventually for guiding the design of new, robust catalysts for selective electrosynthesis under dynamic operation.

10.
Phys Chem Chem Phys ; 20(36): 23702-23716, 2018 Sep 19.
Artigo em Inglês | MEDLINE | ID: mdl-30191927

RESUMO

We have studied particle size effects on atomically-defined model catalysts both in ultrahigh vacuum (UHV) and under electrochemical (EC) conditions in liquid electrolytes. The model catalysts were prepared in UHV by physical vapour deposition (PVD) of Pt onto an ordered Co3O4(111) film on Ir(100), yielding nanoparticles (NPs) with an average size from 10 to 500 atoms per particle (0.8 to 3 nm). The model systems were characterized in UHV using surface science methods including scanning tunnelling microscopy (STM), before transferring them out of the UHV and into the electrolyte without contact to ambient conditions. By X-ray photoelectron spectroscopy (XPS) we show that the model surfaces are stable in the EC environment under the applied conditions (0.1 to 1 M phosphate buffer, pH 10, 0.33 to 1.03 VRHE). As a reference, we study Pt(111) under identical conditions. In UHV, we also investigated the adsorption of CO using infrared reflection absorption spectroscopy (IRRAS). Under EC conditions, we performed equivalent experiments using EC infrared reflection absorption spectroscopy (EC-IRRAS) in combination with cyclic voltammetry (CV). Characteristic differences were observed between the IR spectra under EC conditions and in UHV. Besides the red-shift induced by the interfacial electric field (Stark effect), the EC IR bands of CO on Pt(111) show a larger width (by a factor of 2) as a result of local variations in the CO environment and coupling to the electrolyte. The CO IR bands of the Pt NPs are even broader (by a factor of 5), which is attributed to local variations of the interfacial electric field at the NP surface. Further pronounced differences are observed between the spectra taken in UHV and in the electrolyte regarding the site occupation and its dependence on particle size. In UHV, adsorption at on-top sites is preferred on Pt(111) at low coverage and similar adsorption ratios of on-top and bridge-bonded CO are formed at saturation coverage. In sharp contrast, on-top adsorption of CO on Pt(111) is partially suppressed under EC conditions. This effect is attributed to the competitive adsorption of anions from the electrolyte and leads to a clear preference for bridge sites at higher potentials (>0.5 VRHE). For the Pt NPs, the situation is different and an increasing fraction of on-top CO is observed with decreasing particle size, both under EC conditions and in UHV. For the smallest particles (10-20 atoms) we do not detect any bridge-bonded CO. This change in site preference as a function of particle size is attributed to stronger on-top adsorption on low-coordinated Pt atoms of small Pt NPs. The effect leads to a clear preference for on-top adsorption in the electrolyte even at low CO coverage and over the full potential range studied.

11.
J Phys Chem Lett ; 7(3): 387-92, 2016 Feb 04.
Artigo em Inglês | MEDLINE | ID: mdl-26757266

RESUMO

The two traditional mechanisms of the electrochemical ammonia oxidation consider only concerted proton-electron transfer elementary steps and thus they predict that the rate-potential relationship is independent of the pH on the pH-corrected RHE potential scale. In this letter we show that this is not the case: the increase of the solution pH shifts the onset of the NH3-to-N2 oxidation on Pt(100) to lower potentials and also leads to higher surface concentration of formed NOad before the latter is oxidized to nitrite. Therefore, we present a new mechanism for the ammonia oxidation that incorporates a deprotonation step occurring prior to the electron transfer. The deprotonation step yields a negatively charged surface-adsorbed species that is discharged in a subsequent electron transfer step before the N-N bond formation. The negatively charged species is thus a precursor for the formation of N2 and NO. The new mechanism should be a future guide for computational studies aiming at the identification of intermediates and corresponding activation barriers for the elementary steps. Ammonia oxidation is a new example of a bond-forming reaction on (100) terraces that involves decoupled proton-electron transfer.

12.
Beilstein J Nanotechnol ; 5: 44-67, 2014.
Artigo em Inglês | MEDLINE | ID: mdl-24605273

RESUMO

Platinum and Pt alloy nanoparticles supported on carbon are the state of the art electrocatalysts in proton exchange membrane fuel cells. To develop a better understanding on how material design can influence the degradation processes on the nanoscale, three specific Pt/C catalysts with different structural characteristics were investigated in depth: a conventional Pt/Vulcan catalyst with a particle size of 3-4 nm and two Pt@HGS catalysts with different particle size, 1-2 nm and 3-4 nm. Specifically, Pt@HGS corresponds to platinum nanoparticles incorporated and confined within the pore structure of the nanostructured carbon support, i.e., hollow graphitic spheres (HGS). All three materials are characterized by the same platinum loading, so that the differences in their performance can be correlated to the structural characteristics of each material. The comparison of the activity and stability behavior of the three catalysts, as obtained from thin film rotating disk electrode measurements and identical location electron microscopy, is also extended to commercial materials and used as a basis for a discussion of general fuel cell catalyst design principles. Namely, the effects of particle size, inter-particle distance, certain support characteristics and thermal treatment on the catalyst performance and in particular the catalyst stability are evaluated. Based on our results, a set of design criteria for more stable and active Pt/C and Pt-alloy/C materials is suggested.

13.
Angew Chem Int Ed Engl ; 53(1): 102-21, 2014 Jan 03.
Artigo em Inglês | MEDLINE | ID: mdl-24339359

RESUMO

Electrochemistry will play a vital role in creating sustainable energy solutions in the future, particularly for the conversion and storage of electrical into chemical energy in electrolysis cells, and the reverse conversion and utilization of the stored energy in galvanic cells. The common challenge in both processes is the development of-preferably abundant-nanostructured materials that can catalyze the electrochemical reactions of interest with a high rate over a sufficiently long period of time. An overall understanding of the related processes and mechanisms occurring under the operation conditions is a necessity for the rational design of materials that meet these requirements. A promising strategy to develop such an understanding is the investigation of the impact of material properties on reaction activity/selectivity and on catalyst stability under the conditions of operation, as well as the application of complementary in situ techniques for the investigation of catalyst structure and composition.

14.
Phys Chem Chem Phys ; 15(21): 8058-68, 2013 Jun 07.
Artigo em Inglês | MEDLINE | ID: mdl-23515463

RESUMO

The impact of electrolyte constituents on the interaction of hydrogen peroxide with polycrystalline platinum is decisive for the understanding of the selectivity of the oxygen reduction reaction (ORR). Hydrodynamic voltammetry measurements show that while the hydrogen peroxide reduction (PRR) is diffusion-limited in perchlorate- or fluoride-containing solutions, kinetic limitations are introduced by the addition of more strongly adsorbing anions. The strength of the inhibition of the PRR increases in the order ClO4(-)≈ F(-) < HSO4(-) < Cl(-) < Br(-) < I(-) as well as with the increase of the concentration of the strongly adsorbing anions. Electronic structure calculations indicate that the dissociation of H2O2 on Pt(111) is always possible, regardless of the coverage of spectator species. However, the adsorption of H2O2 becomes strongly endothermic at high coverage with adsorbing anions. A comparison of our observations on the inhibition of the PRR by spectators with previous studies on the selectivity of the ORR shows that oxygen is reduced to H2O2 only under conditions at which the PRR kinetics is significantly limited, while the ORR proceeds with a complete four-electron reduction only when the PRR is sufficiently fast. Therefore, only a H2O2-mediated pathway that includes a competition between the dissociation and the spectator coverage-dependent desorption of the H2O2 intermediate is enough to explain and unify all the observations that have been made so far on the selectivity of the ORR.


Assuntos
Eletrólitos/química , Peróxido de Hidrogênio/química , Oxigênio/química , Platina/química , Adsorção , Modelos Moleculares , Oxirredução , Sulfatos/química
15.
Environ Technol ; 34(1-4): 373-81, 2013.
Artigo em Inglês | MEDLINE | ID: mdl-23530351

RESUMO

The effect of the nature of six metal electrodes (Sn, Bi, Pb, Al, Zn, In) on the rate and the distribution of the products of the electrochemical reduction of nitrate was studied. The product distribution depends on the nature of the metal only quantitatively, while the rate of the reduction was found to be about the same on all metals when the electrolysis was performed at the same rational potential (E(r)), which is the difference between the applied potential and the potential of zero charge of each metal. Based on these results it was concluded that the mechanism of nitrate reduction is the same for all cathodes studied. Additionally, the influence of the initial pH on the rate of the reduction of nitrate and the selectivity of the products on a tin cathode was studied. The rate of the reduction increases linearly with the concentration of hydronium ion in the pH range 0-4, whereas it is not dependent on the pH at higher pH values. The main products at pH > 4 were nitrogen, nitrous oxide, ammonia and nitrite, while at pH 0-4 ammonia and hydroxylamine were mainly formed.


Assuntos
Eletrólise , Eletrólitos/química , Metais/química , Nitratos/química , Eletrodos , Concentração de Íons de Hidrogênio , Concentração Osmolar , Oxirredução
16.
Angew Chem Int Ed Engl ; 51(50): 12613-5, 2012 Dec 07.
Artigo em Inglês | MEDLINE | ID: mdl-23124819

RESUMO

Platinum stability: Dissolution of Pt, which is one major degradation mechanism in, for example, hydrogen/air fuel cells, was monitored under potentiodynamic and potentiostatic conditions. The highly sensitive and time-resolving dissolution monitoring enables the distinction between anodic and cathodic dissolution processes during potential transient and chronoamperometric experiments, and the precise quantification of the amount of dissolved Pt.


Assuntos
Fontes Geradoras de Energia , Platina/química , Catálise , Técnicas Eletroquímicas , Eletrodos , Hidrogênio/química
17.
J Am Chem Soc ; 134(50): 20457-65, 2012 Dec 19.
Artigo em Inglês | MEDLINE | ID: mdl-23190415

RESUMO

The durability of electrode materials is a limiting parameter for many electrochemical energy conversion systems. In particular, electrocatalysts for the essential oxygen reduction reaction (ORR) present some of the most challenging instability issues shortening their practical lifetime. Here, we report a mesostructured graphitic carbon support, Hollow Graphitic Spheres (HGS) with a specific surface area exceeding 1000 m(2) g(-1) and precisely controlled pore structure, that was specifically developed to overcome the long-term catalyst degradation, while still sustaining high activity. The synthetic pathway leads to platinum nanoparticles of approximately 3 to 4 nm size encapsulated in the HGS pore structure that are stable at 850 °C and, more importantly, during simulated accelerated electrochemical aging. Moreover, the high stability of the cathode electrocatalyst is also retained in a fully assembled polymer electrolyte membrane fuel cell (PEMFC). Identical location scanning and scanning transmission electron microscopy (IL-SEM and IL-STEM) conclusively proved that during electrochemical cycling the encapsulation significantly suppresses detachment and agglomeration of Pt nanoparticles, two of the major degradation mechanisms in fuel cell catalysts of this particle size. Thus, beyond providing an improved electrocatalyst, this study describes the blueprint for targeted improvement of fuel cell catalysts by design of the carbon support.

18.
Chem Commun (Camb) ; 48(53): 6660-2, 2012 Jul 07.
Artigo em Inglês | MEDLINE | ID: mdl-22635133

RESUMO

The potential range of the transition region between the diffusion-limited reduction to oxidation of hydrogen peroxide depends strongly on the nature of the cation of the supporting alkaline electrolyte. Non-covalent interactions between the hydrated alkali metal cations and chemisorbed OH species on platinum influence the potential-dependent reaction kinetics.

19.
Phys Chem Chem Phys ; 14(20): 7384-91, 2012 May 28.
Artigo em Inglês | MEDLINE | ID: mdl-22517633

RESUMO

Understanding the hydrogen peroxide electrochemistry on platinum can provide information about the oxygen reduction reaction mechanism, whether H(2)O(2) participates as an intermediate or not. The H(2)O(2) oxidation and reduction reaction on polycrystalline platinum is a diffusion-limited reaction in 0.1 M HClO(4). The applied potential determines the Pt surface state, which is then decisive for the direction of the reaction: when H(2)O(2) interacts with reduced surface sites it decomposes producing adsorbed OH species; when it interacts with oxidized Pt sites then H(2)O(2) is oxidized to O(2) by reducing the surface. Electronic structure calculations indicate that the activation energies of both processes are low at room temperature. The H(2)O(2) reduction and oxidation reactions can therefore be utilized for monitoring the potential-dependent oxidation of the platinum surface. In particular, the potential at which the hydrogen peroxide reduction and oxidation reactions are equally likely to occur reflects the intrinsic affinity of the platinum surface for oxygenated species. This potential can be experimentally determined as the crossing-point of linear potential sweeps in the positive direction for different rotation rates, hereby defined as the "ORR-corrected mixed potential" (c-MP).

20.
Rev Sci Instrum ; 82(11): 114103, 2011 Nov.
Artigo em Inglês | MEDLINE | ID: mdl-22128995

RESUMO

This paper describes a system for performing electrochemical catalyst testing where all hardware components are controlled simultaneously using a single LabVIEW-based software application. The software that we developed can be operated in both manual mode for exploratory investigations and automatic mode for routine measurements, by using predefined execution procedures. The latter enables the execution of high-throughput or combinatorial investigations, which decrease substantially the time and cost for catalyst testing. The software was constructed using a modular architecture which simplifies the modification or extension of the system, depending on future needs. The system was tested by performing stability tests of commercial fuel cell electrocatalysts, and the advantages of the developed system are discussed.

SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA