Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 10 de 10
Filtrar
Mais filtros










Base de dados
Intervalo de ano de publicação
1.
Adv Sci (Weinh) ; 8(19): e2102213, 2021 Oct.
Artigo em Inglês | MEDLINE | ID: mdl-34453782

RESUMO

While tremendous progress has recently been made in perovskite light-emitting diodes (PeLEDs), large-area blue devices feature inferior performance due to uneven morphologies and vast defects in the solution-processed perovskite films. To alleviate these issues, a facile and reliable interface engineering scheme is reported for manipulating the crystallization of perovskite films enabled by a multifunctional molecule 2-amino-1,3-propanediol (APDO)-triggered "anchoring effect" at the grain-growth interface. Sky-blue perovskite films with large-area uniformity and low trap states are obtained, showing the distinctly improved radiative recombination and hole-transport capability. Based on the APDO-induced interface engineering, synergistical boost in device performance is achieved for large-area sky-blue PeLED (measuring at 100 mm2 ) with a peak external quantum efficiency (EQE) of 9.2% and a highly prolonged operational lifetime. A decent EQE up to 6.1% is demonstrated for the largest sky-blue device emitting at 400 mm2 .

2.
J Phys Chem Lett ; 12(18): 4362-4367, 2021 May 13.
Artigo em Inglês | MEDLINE | ID: mdl-33938752

RESUMO

Regardless of the impressive photovoltaic performances demonstrated for lead halide perovskite solar cells, their practical implementation is severely impeded by the low device stability. Complex lead halides are sensitive to both light and heat, which are unavoidable under realistic solar cell operational conditions. Suppressing these intrinsic degradation pathways requires a thorough understanding of their mechanistic aspects. Herein, we explored the temperature effects in the light-induced decomposition of MAPbI3 and PbI2 thin films under anoxic conditions. The analysis of the aging kinetics revealed that MAPbI3 photolysis and PbI2 photolysis have quite high effective activation energies of ∼85 and ∼106 kJ mol-1, respectively, so decreasing the temperature from 55 to 30 °C can extend the perovskite lifetime by factors of >10-100. These findings suggest that controlling the temperature of the perovskite solar panels might allow the long operational lifetimes (>20 years) required for the practical implementation of this promising technology.

3.
ACS Appl Mater Interfaces ; 12(16): 19161-19173, 2020 Apr 22.
Artigo em Inglês | MEDLINE | ID: mdl-32233360

RESUMO

We investigated the impact of a series of hole transport layer (HTL) materials such as Poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS), NiOx, poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine (PTAA), and polytriarylamine (PTA) on photostability of thin films and solar cells based on MAPbI3, Cs0.15FA0.85PbI3, Cs0.1MA0.15FA0.75PbI3, Cs0.1MA0.15FA0.75Pb(Br0.15I0.85)3, and Cs0.15FA0.85Pb(Br0.15I0.85)3 complex lead halides. Mixed halide perovskites showed reduced photostability in comparison with similar iodide-only compositions. In particular, we observed light-induced recrystallization of all perovskite films except MAPbI3 with the strongest effects revealed for Br-containing systems. Moreover, halide and ß FAPbI3 phase segregations were also observed mostly in mixed-halide systems. Interestingly, coating perovskite films with the PCBM layer spectacularly suppressed light-induced growth of crystalline domains as well as segregation of Br-rich and I-rich phases or ß FAPbI3. We strongly believe that all three effects are promoted by the light-induced formation of surface defects, which are healed by adjacent PCBM coating. While comparing different hole-transport materials, we found that NiOx and PEDOT:PSS are the least suitable HTLs because of their interfacial (photo)chemical interactions with perovskite absorbers. On the contrary, polyarylamine-type HTLs PTA and PTAA form rather stable interfaces, which makes them the best candidates for durable p-i-n perovskite solar cells. Indeed, multilayered ITO/PTA(A)/MAPbI3/PCBM stacks revealed no aging effects within 1000 h of continuous light soaking and delivered stable and high power conversion efficiencies in solar cells. The obtained results suggest that using polyarylamine-type HTLs and simple single-phase perovskite compositions pave a way for designing stable and efficient perovskite solar cells.

4.
J Phys Chem Lett ; 11(7): 2630-2636, 2020 Apr 02.
Artigo em Inglês | MEDLINE | ID: mdl-32178515

RESUMO

In this work, we report a comparative study of the gamma ray stability of perovskite solar cells based on a series of perovskite absorbers including MAPbI3 (MA = methylammonium), MAPbBr3, Cs0.15FA0.85PbI3 (FA = formamidinim), Cs0.1MA0.15FA0.75PbI3, CsPbI3, and CsPbBr3. We reveal that the composition of the perovskite material strongly affects the radiation stability of the solar cells. In particular, solar cells based on the MAPbI3 were found to be the most resistant to gamma rays since this perovskite undergoes rapid self-healing due to the special gas-phase chemistry analyzed with ab initio calculations. The fact that the solar cells based on MAPbI3 can withstand a 1000 kRad gamma ray dose without any noticeable degradation of the photovoltaic properties is particularly exciting and shifts the paradigm of research in this field toward designing more dynamic rather than intrinsically robust (e.g., inorganic) materials.

5.
Chem Commun (Camb) ; 56(10): 1541-1544, 2020 Feb 04.
Artigo em Inglês | MEDLINE | ID: mdl-31922170

RESUMO

We report the application of a Ni-based coordination polymer derived from 1,2,4,5-tetraaminobenzene (P1) as a fast and stable potassium battery anode. In a voltage range of 0.5-2.0 V vs. K+/K, a reversible capacity of 220 mA h g-1 was obtained at 0.1 A g-1. Even with a relatively high electrode loading of 5.0 mg cm-2 and only 10 wt% carbon additive, 118 mA h g-1 was still retained at 1 A g-1. For thinner electrodes with 30 wt% carbon, a capacity of up to 104 mA h g-1 was observed at 10 A g-1 (charging in ∼40 seconds). An areal capacity of up to 2.73 mA h cm-2 was demonstrated. The capacity fade at 1 A g-1 was only 4.4% after 200 cycles. Structure transformations of P1 during charge/discharge were studied using X-ray photoelectron spectroscopy and in situ X-ray diffraction.

6.
J Phys Condens Matter ; 32(9): 095501, 2020 Feb 27.
Artigo em Inglês | MEDLINE | ID: mdl-31722319

RESUMO

In this study, we investigate the photo-/thermal degradation mechanism of hybrid perovskites by using x-ray photoelectron (XPS) valence band (VB) spectra coupling with density functional theory (DFT) calculations. Herein, CH3NH3PbI3 is respectively subjected to irradiation with visible light and annealing at an exposure of 0-1000 h. It is found from XPS survey spectra that, in both cases (irradiation and annealing), a decrease in the I:Pb ratio is observed with aging time, which unambiguously indicates the formation of PbI2 as the product of photo/thermal degradation. The comparison of the XPS VB spectra of irradiated and annealed perovskites with the DFT calculations of CH3NH3PbI3 and PbI2 compounds have showed a systematic decrease in the contribution of I-5p states, which allows us to determine the respective threshold for degradation, which is 500 h for light irradiation and 200 h for annealing. This discrepancy might be due to the fact that the relaxation of thermal excitations of the system is carried out only by the phonons (which are non-radiative physical processes) while the radiative processes occurred during the photoexcitation will elastically or inelastically divert part of the external energy from the system to reduce its impact on perovskite degradation.

7.
J Phys Chem A ; 124(1): 135-140, 2020 Jan 09.
Artigo em Inglês | MEDLINE | ID: mdl-31820980

RESUMO

Thermal effects in organo-metal halide perovskites are studied by ab initio molecular dynamics (MD) simulations performed at effective temperatures of 293 and 383 K and by X-ray photoelectron spectroscopy (XPS). We find that the cause of thermal instability in this class of perovskites is the rotation of the methylammonium (MA) groups that destroy the rigid lattice of pure compounds (MAPbI3 and MAPbBr3). When the Pb-I lattice is initially distorted by partial replacement of the I with Cl or Br, this not only prevents formation of PbI2 seeds but also improves lattice flexibility and stability against the temperature-induced motion and rotation of MA groups.

8.
J Phys Chem Lett ; 10(4): 813-818, 2019 Feb 21.
Artigo em Inglês | MEDLINE | ID: mdl-30621392

RESUMO

We report on the impact of γ radiation (0-500 Gy) on triple-cation Cs0.15MA0.10FA0.75Pb(Br0.17I0.83)3 perovskite solar cells. A set of experiments was designed to reveal the individual contributions of the hole-collecting bottom electrode, perovskite absorber, and electron transport layer (ETL) to the overall solar cell degradation under radiation exposure. We show that the glass/ITO/PEDOT:PSS hole-collecting electrode withstands a 500 Gy dose without any losses in the solar cell performance. In contrast, the perovskite absorber films and PC61BM ETL are very sensitive to γ rays, as can be concluded from the radiation-induced decay of the solar cell efficiency by ∼32-41%. Red shift of the perovskite emission bands and strong enhancement of the photoluminescence suggest that γ rays induce phase segregation of iodine-rich and bromine-rich domains, which represents the first reported example of the radiation-induced halide phase separation in perovskite films. The degradation pathway revealed here emphasizes the need for developing a new generation of metal halide absorbers and ETL materials with improved radiation stability to enable potential space applications of perovskite photovoltaics.

9.
J Phys Chem Lett ; 8(6): 1211-1218, 2017 Mar 16.
Artigo em Inglês | MEDLINE | ID: mdl-28220700

RESUMO

We report a careful and systematic study of thermal and photochemical degradation of a series of complex haloplumbates APbX3 (X = I, Br) with hybrid organic (A+ = CH3NH3) and inorganic (A+ = Cs+) cations under anoxic conditions (i.e., without exposure to oxygen and moisture by testing in an inert glovebox environment). We show that the most common hybrid materials (e.g., MAPbI3) are intrinsically unstable with respect to the heat- and light-induced stress and, therefore, can hardly sustain the real solar cell operation conditions. On the contrary, the cesium-based all-inorganic complex lead halides revealed far superior stability and, therefore, provide an impetus for creation of highly efficient and stable perovskite solar cells that can potentially achieve pragmatic operational benchmarks.

10.
J Chem Phys ; 143(22): 224704, 2015 Dec 14.
Artigo em Inglês | MEDLINE | ID: mdl-26671393

RESUMO

The electronic structure of [6,6]-phenyl C61 butyric acid methyl ester (PCBM), poly(3-hexylthiophene) (P3HT), and P3HT/PCBM blends is studied using soft X-ray emission and absorption spectroscopy and density functional theory calculations. We find that annealing reduces the HOMO-LUMO gap of P3HT and P3HT/PCBM blends, whereas annealing has little effect on the HOMO-LUMO gap of PCBM. We propose a model connecting torsional disorder in a P3HT polymer to the HOMO-LUMO gap, which suggests that annealing helps to decrease the torsional disorder in the P3HT polymers. Our model is used to predict the characteristic length scales of the flat P3TH polymer segments in P3HT and P3HT/PCBM blends before and after annealing. Our approach may prove useful in characterizing organic photovoltaic devices in situ or even in operando.


Assuntos
Fulerenos/química , Polímeros/química , Teoria Quântica , Tiofenos/química , Elétrons
SELEÇÃO DE REFERÊNCIAS
DETALHE DA PESQUISA
...