Insight into the Role of Rb Doping for Highly Efficient Kesterite Cu2ZnSn(S,Se)4 Solar Cells.

Various copper-related defects in the absorption layer have been a key factor impeding the enhancement of the efficiency of Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. Alkali metal doping is considered to be a good strategy to ameliorate this problem. In this article, Rb-doped CZTSSe (RCZTSSe) thin films were synthesized using the sol-gel technique. The results show that the Rb atom could successfully enter into the CZTSSe lattice and replace the Cu atom. According to SEM results, a moderate amount of Rb doping aided in enhancing the growth of grains in CZTSSe thin films. It was proven that the RCZTSSe thin film had the densest surface morphology and the fewest holes when the doping content of Rb was 2%. In addition, Rb doping successfully inhibited the formation of CuZn defects and correlative defect clusters and promoted the electrical properties of RCZTSSe thin films. Finally, a remarkable power conversion efficiency of 7.32% was attained by the champion RCZTSSe device with a Rb content of 2%. Compared with that of un-doped CZTSSe, the efficiency improved by over 30%. This study offers new insights into the influence of alkali metal doping on suppressing copper-related defects and also presents a viable approach for improving the efficiency of CZTSSe devices.

In Situ Vanadium Modification Induced a Back Interfacial Field Passivation Effect toward Efficient Kesterite Solar Cells beyond 11% Efficiency.

Realization of a high-quality back electrode interface (BEI) with suppressed recombination is crucial for Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. To achieve this goal, the construction of a traditional chemical passivation effect has been widely adopted and investigated. However, there is currently a lack of reports concerning the construction of a field passivation effect (FPE) for the BEI. Herein, considering the characteristic of the negligible difference in ionic radius between Mo (0.65 Å) and V (0.64 Å) as well as the presence of one less valence electron compared to Mo, vanadium (V) was employed and in situ incorporated into the MoSe2 interfacial layer during the deposition of the Mo:V electrode and selenization process. This allowed for the establishment of a desirable in situ VI-FPE interface with p-MoSe2:V/p-CZTSSe at the BEI. The p-type characteristic in MoSe2:V is attributed to the presence of the VMo acceptor; notably, the Fermi energy level of MoSe2:V has shifted downward by 0.62 eV compared to MoSe2, thereby facilitating the formation of an optimized band alignment between MoSe2:V and the absorber. Consequently, the photovoltaic parameters of the cell-FPE have experienced a significant increase due to the enhanced carrier transportation efficiency compared to cell-ref, resulting in a remarkable improvement in efficiency from 8.28 to 11.11%.

Synergistic Crystallization Modulation and Defects Passivation in Kesterite via Anion-Coordinate Precursor Engineering for Efficient Solar Cells.

It has been validated that enhancing crystallinity and passivating the deep-level defect are critical for improving the device performance of kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. Coordination chemistry interactions within the Cu-Zn-Sn-S precursor solution play a crucial role in the management of structural defects and the crystallization kinetics of CZTSSe thin films. Therefore, regulating the coordination environment of anion and cation in the precursor solution to control the formation process of precursor films is a major challenge at present. Herein, a synergetic crystallization modulation and defect passivation method is developed using P2S5 as an additive in the CZTS precursor solution to optimize the coordination structure and improve the crystallization process. The alignment of theoretical assessments with experimental observations confirms the ability of the P2S5 molecule to coordinate with the metal cation sites of CZTS precursor films, especially more liable to the Zn2+, effectively passivating the Zn-related defects, thereby significantly reducing the defect density in CZTSSe absorbers. As a result, the device with a power conversion efficiency of 14.36% has been achieved. This work provides an unprecedented strategy for fabricating high-quality thin films by anion-coordinate regulation and a novel route for realizing efficient CZTSSe solar cells.

Segmented Control of Selenization Environment for High-Quality Cu2ZnSn(S,Se)4 Films Toward Efficient Kesterite Solar Cells.

High-crystalline-quality absorbers with fewer defects are crucial for further improvement of open-circuit voltage (VOC) and efficiency of Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. However, the preparation of high-quality CZTSSe absorbers remains challenging due to the uncontrollability of the selenization reaction and the complexity of the required selenization environment for film growth. Herein, a novel segmented control strategy for the selenization environment, specifically targeting the evaporation area of Se, to regulate the selenization reactions and improve the absorber quality is proposed. The large evaporation area of Se in the initial stage of the selenization provides a great evaporation and diffusion flux for Se, which facilitates rapid phase transition reactions and enables the attainment of a single-layer thin film. The reduced evaporation area of Se in the later stage creates a soft-selenization environment for grain growth, effectively suppressing the loss of Sn and promoting element homogenization. Consequently, the mitigation of Sn-related deep-level defects on the surface and in the bulk induced by element imbalance is simultaneously achieved. This leads to a significant improvement in nonradiative recombination suppression and carrier collection enhancement, thereby enhancing the VOC. As a result, the CZTSSe device delivers an impressive efficiency of 13.77% with a low VOC deficit.

Fostering Charge Carrier Transport and Absorber Growth Properties in CZTSSe Thin Films with an ALD-SnO2 Capping Layer.

The present study demonstrates that precursor passivation is an effective approach for improving the crystallization process and controlling the detrimental defect density in high-efficiency Cu2ZnSn(S,Se)4 (CZTSSe) thin films. It is achieved by applying the atomic layer deposition (ALD) of the tin oxide (ALD-SnO2) capping layer onto the precursor (Cu-Zn-Sn) thin films. The ALD-SnO2 capping layer was observed to facilitate the homogeneous growth of crystalline grains and mitigate defects prior to sulfo-selenization in CZTSSe thin films. Particularly, the CuZn and SnZn defects and deep defects associated with Sn were effectively mitigated due to the reduction of Sn2+ and the increase in Sn4+ levels in the kesterite CZTSSe film after introducing ALD-SnO2 on the precursor films. Subsequently, devices integrating the ALD-SnO2 layer exhibited significantly reduced recombination and efficient charge transport at the heterojunction interface and within the bulk CZTSSe absorber bulk properties. Finally, the CZTSSe device showed improved power conversion efficiency (PCE) from 8.46% to 10.1%. The incorporation of ALD-SnO2 revealed reduced defect sites, grain boundaries, and surface roughness, improving the performance. This study offers a systematic examination of the correlation between the incorporation of the ALD-SnO2 layer and the improved PCE of CZTSSe thin film solar cells (TFSCs), in addition to innovative approaches for improving absorber quality and defect control to advance the performance of kesterite CZTSSe devices.

Improvement of Efficiency in Kesterite Solar Cells by Intentionally Inserting a Thin MoS2 Layer into the Back Interface.

A Mo(S,Se)2 interfacial layer is formed inevitably and uncontrollably between the Mo electrode and Cu2ZnSn(S,Se)4 (CZTSSe) absorber during the selenization process, which significantly influences the performance of CZTSSe solar cells. In this work, an ultrathin MoS2 layer is intentionally inserted into Mo/CZTSSe to reduce the recombination and thus optimize the interface quality. It is revealed that the absorber exhibits a continuous and compact morphology with bigger grains and remarkably without pinholes across the surface or cross-sectional regions after MoS2 modification. Benefitting from this, the shunt resistance (RSh) of the device increased evidently from ∼395 to ∼634 Ω·cm2, and simultaneously, the reverse saturation current density (J0) realized an effective depression. As a result, the power conversion efficiency (PCE) of the MoS2-modified device reaches 9.64% via the optimization of the thickness of the MoS2 layer, indicating performance improvements with respect to the MoS2-free case. Furthermore, the main contribution to the performance improvement is derived and analyzed in detail from the increased RSh, decreased J0, and diode ideality factor. Our results suggest that the Mo/CZTSSe interface quality and performance of CZTSSe solar cells can be modulated and improved by appropriately designing and optimizing the thickness of the inserted MoS2 layer.

Suppressing Element Inhomogeneity Enables 14.9% Efficiency CZTSSe Solar Cells.

Kesterites, Cu2ZnSn(SxSe1- x)4 (CZTSSe), solar cells suffer from severe open-circuit voltage (VOC) loss due to the numerous secondary phases and defects. The prevailing notion attributes this issue to Sn-loss during the selenization. However, this work unveils that, instead of Sn-loss, elemental inhomogeneity caused by Cu-directional diffusion toward Mo(S,Se)2 layer is the critical factor in the formation of secondary phases and defects. This diffusion decreases the Cu/(Zn+Sn) ratio to 53% at the bottom fine-grain layer, increasing the Sn-/Zn-related bulk defects. By suppressing the Cu-directional diffusion with a blocking layer, the crystal quality is effectively improved and the defect density is reduced, leading to a remarkable photovoltaic coversion efficiency (PCE) of 14.9% with a VOC of 576 mV and a certified efficiency of 14.6%. The findings provide insights into element inhomogeneity, holding significant potential to advance the development of CZTSSe solar cells.

Modifying Surface Termination by Bidentate Chelating Strategy Enables 13.77% Efficient Kesterite Solar Cells.

Surfaces display discontinuities in the kesterite-based polycrystalline films can produce large defect densities, including strained and dangling bonds. These physical defects tend to introduce electronic defects and surface states, which can greatly promote nonradiative recombination of electron-hole pairs and damage device performance. Here, an effective chelation strategy is reported to suppress these harmful physical defects related to unterminated Cu, Zn, and Sn sites by modifying the surface of Cu2ZnSn(S,Se)4 (CZTSSe) films with sodium diethyldithiocarbamate (NaDDTC). The conjoint theoretical calculations and experimental results reveal that the NaDDTC molecules can be coordinate to surface metal sites of CZTSSe films via robust bidentate chelating interactions, effectively reducing surface undercoordinated defects and passivating the electron trap states. Consequently, the solar cell efficiency of the NaDDTC-treated device is increased to as high as 13.77% under 100 mW cm-2 illumination, with significant improvement in fill factor and open-circuit voltage. This surface chelation strategy provides strong surface termination and defect passivation for further development and application of kesterite-based photovoltaics.

Passivating Grain Boundaries via Graphene Additive for Efficient Kesterite Solar Cells.

Grain boundaries (GBs)-triggered severe non-radiative recombination is recently recognized as the main culprits for carrier loss in polycrystalline kesterite photovoltaic devices. Accordingly, further optimization of kesterite-based thin film solar cells critically depends on passivating the grain interfaces of polycrystalline Cu2 ZnSn(S,Se)4 (CZTSSe) thin films. Herein, 2D material of graphene is first chosen as a passivator to improve the detrimental GBs. By adding graphene dispersion to the CZTSSe precursor solution, single-layer graphene is successfully introduced into the GBs of CZTSSe absorber. Due to the high carrier mobility and electrical conductivity of graphene, GBs in the CZTSSe films are transforming into electrically benign and do not act as high recombination sites for carrier. Consequently, benefitting from the significant passivation effect of GBs, the use of 0.05 wt% graphene additives increases the efficiency of CZTSSe solar cells from 10.40% to 12.90%, one of the highest for this type of cells. These results demonstrate a new route to further increase kesterite-based solar cell efficiency by additive engineering.

Visual Color Change During Spin-coating Guiding the Quality of Cu2 ZnSn(S,Se)4 Films.

Solution method provides a low-cost and environmentally friendly route for the fabrication of Cu2 ZnSn(S,Se)4 (CZTSSe) thin-film solar cells. However, uncontrollable quality of the CZTSSe absorber layer will severely limit the device's performance. In this study, it is find that the thickness and the quality of the formed precursor is not stable because of the variation of the viscosity of the precursor solution. Combined by different characterization methods, the results disclose that such change is strongly related to the reflected color of the first coating layer during precursor growth. Further studies disclose that only by maintaining the appropriate reflected color can a well-crystallized CZTSSe film be prepared, thereby obtaining good solar cell efficiency. This semi-empirical pattern is confirmed by thin-film interference theory. Under the guidance of this method, CZTSSe absorbers with high quality are obtained easily, and the highly efficient CZTSSe solar cell can be fabricated easily. This study provides a feasible and effective strategy to obtain the optimal structure and composition of CZTSSe film toward the production of highly efficient kesterite solar cells, which can also be widely applied to the preparation of other films by solution-based method.

Defect Synergistic Regulations of Li&Na Co-Doped Flexible Cu2 ZnSn(S,Se)4 Solar Cells Achieving over 10% Certified Efficiency.

Ion doping is an effective strategy for achieving high-performance flexible Cu2 ZnSn(S,Se)4 (CZTSSe) solar cells by defect regulations. Here, a Li&Na co-doped strategy is applied to synergistically regulate defects in CZTSSe bulks. The quality absorbers with the uniformly distributed Li and Na elements are obtained using the solution method, where the acetates (LiAc and NaAc) are as additives. The concentration of the harmful CuZn anti-site defects is decreased by 8.13% after Li incorporation, and that of the benign NaZn defects is increased by 36.91% after Na incorporation. Synergistic Li&Na co-doping enhances the carrier concentration and reduces the interfacial defects concentration by one order of magnitude. As a result, the flexible CZTSSe solar cell achieves a power conversion efficiency (PCE) of 10.53% with certified 10.12%. Because of the high PCE and the homogeneous property, the Li&Na co-doped device is fabricated to a large area (2.38 cm2 ) and obtains 9.41% PCE. The co-doping investigation to synergistically regulate defects provides a new perspective for efficient flexible CZTSSe solar cells.

Regulating Hetero-Nucleation Enabling Over 14% Efficient Kesterite Solar Cells.

Developing well-crystallized light-absorbing layers remains a formidable challenge in the progression of kesterite Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. A critical aspect of optimizing CZTSSe lies in accurately governing the high-temperature selenization reaction. This process is intricate and demanding, with underlying mechanisms requiring further comprehension. This study introduces a precursor microstructure-guided hetero-nucleation regulation strategy for high-quality CZTSSe absorbers and well-performing solar cells. The alcoholysis of 2-methoxyethanol (MOE) and the generation of high gas-producing micelles by adding hydrogen chloride (HCl) as a proton additive into the precursor solution are successfully suppressed. This tailored modification of solution components reduces the emission of volatiles during baking, yielding a compact and dense precursor microstructure. The reduced-roughness surface nurtures the formation of larger CZTSSe nuclei, accelerating the ensuing Ostwald ripening process. Ultimately, CZTSSe absorbers with enhanced crystallinity and diminished defects are fabricated, attaining an impressive 14.01% active-area power conversion efficiency. The findings elucidate the influence of precursor microstructure on the selenization reaction process, paving a route for fabricating high-quality kesterite CZTSSe films and high-efficiency solar cells.

Improving the Device Performance of CZTSSe Thin-Film Solar Cells via Indium Doping.

Cation incorporation emerges as a promising approach for improving the performance of the kesterite Cu2ZnSn(S,Se)4 (CZTSSe) device. Herein, we report indium (In) doping using the chemical bath deposition (CBD) technique to enhance the optoelectronic properties of CZTSSe thin-film solar cells (TFSCs). To incorporate a small amount of the In element into the CZTSSe absorber thin films, an ultrathin (<10 nm) layer of In2S3 is deposited on soft-annealed precursor (Zn-Sn-Cu) thin films prior to the sulfo-selenization process. The successful doping of In improved crystal growth and promoted the formation of larger grains. Furthermore, the CZTSSe TFSCs fabricated with In doping exhibited improved device performance. In particular, the In-CZTSSe-2-based device showed an improved power conversion efficiency (PCE) of 9.53%, open-circuit voltage (Voc) of 486 mV, and fill factor (FF) of 61% compared to the undoped device. Moreover, the small amount of In incorporated into the CZTSSe absorber demonstrated reduced nonradiative recombination, improved carrier separation, and enhanced carrier transport properties. This study suggests a simple and effective way to incorporate In to achieve high efficiency and low Voc loss.

2D Ti3C2-MXene Serving as Intermediate Layer between Absorber and Back Contact for Efficient CZTSSe Solar Cells.

Kesterite Cu2ZnSn(S,Se)4 (CZTSSe) has been considered as the most promising absorber material for inorganic thin-film solar cells. Among the three main interfaces in CZTSSe-based solar cells, the CZTSSe/Mo back interface plays an essential role in hole extraction as well as device performance. During the selenization process, the reaction between CZTSSe and Mo is one of the main reasons that lead to a large open circuit voltage (VOC) deficit, low short circuit current (Jsc), and fill factor. In this study, 2D Ti3C2-MXene was introduced as an intermediate layer to optimize the interface between the CZTSSe absorber layer and Mo back contact. Benefiting from the 2D Ti3C2-MXene intermediate layer, the reaction between CZTSSe and Mo was effectually suppressed, thus, significantly reducing the thickness of the detrimental Mo(S,Se)2 layer as well as interface recombination at the CZTSSe/Mo back interface. As a result, the power conversion efficiency of the champion device fabricated with the 2D Ti3C2-MXene intermediate layer was improved from 10.89 to 13.14% (active-area efficiency). This study demonstrates the potential use of the 2D Ti3C2-MXene intermediate layer for efficient CZTSSe solar cells and promotes a deeper understanding of the back interface in CZTSSe solar cells.

Efficient Environmentally Friendly Flexible CZTSSe/ZnO Solar Cells by Optimizing ZnO Buffer Layers.

Flexible CZTSSe solar cells have attracted much attention due to their earth-abundant elements, high stability, and wide application prospects. However, the environmental problems caused by the high toxicity of the Cd in the buffer layers restrict the development of flexible CZTSSe solar cells. Herein, we develop a Cd-free flexible CZTSSe/ZnO solar cell. The influences of the ZnO films on device performances are investigated. The light absorption capacity of flexible CZTSSe solar cells is enhanced due to the removal of the CdS layer. The optimal thickness of the ZnO buffer layers and the appropriate annealing temperature of the CZTSSe/ZnO are 100 nm and 200 °C. Ultimately, the optimum flexible CZTSSe/ZnO device achieves an efficiency of 5.0%, which is the highest efficiency for flexible CZTSSe/ZnO solar cells. The systematic characterizations indicate that the flexible CZTSSe/ZnO solar cells based on the optimal conditions achieved quality heterojunction, low defect density and better charge transfer capability. This work provides a new strategy for the development of the environmentally friendly and low-cost flexible CZTSSe solar cells.

Microenvironment Created by SnSe2 Vapor and Pre-Selenization to Stabilize the Surface and Back Contact in Kesterite Solar Cells.

The ambient air-processed preparation of kesterite Cu2 ZnSn(S,Se)4 (CZTSSe) thin film is highly promising for the fabrication of low-cost and eco-friendly solar cells. However, the Sn volatilization loss and formation of a thick Mo(S,Se)2 interfacial layer during the traditional selenization process pose challenges for fabricating high-efficiency CZTSSe solar cells. Here, CZTS precursors prepared by a sol-gel process in ambient air are selenized and assisted with SnSe2 vapor via one- and two-step selenization to prepare a CZTSSe absorber on a Mo film and, subsequently, solar cells. For one-step selenization, the thickness of the fine grain and Mo(S,Se)2 layers near the back contact can be significantly reduced with increasing SnSe2 vapor partial pressure in the mixed selenization atmosphere, while the device efficiency is only 7.97% due to the severe interface recombination. For two-step selenization, the desired morphology and stoichiometry of the absorber can be achieved through the assistance of Sn-poor precursors selenized with high SnSe2 vapor partial pressure to regulate the Sn content in CZTSSe, yielding the highest efficiency of 10.85%. This study improves the understanding of the key role of the microenvironment during film growth towards the production of high-efficiency thin film solar cells and other photoelectronic devices.

Doping of Sb into Cu2ZnSn(S,Se)4 absorber layer via Se&Sb2Se3 co-selenization strategy for enhancing open-circuit voltage of kesterite solar cells.

Kesterite-structured Cu2ZnSn(S,Se)4 (CZTSSe) thin film photovoltaics have attracted considerable attention in recent years because of its low-cost and eco-friendly raw material, as well as high theoretical conversion efficiency. However, its photovoltaic performance is hindered by large open-circuit voltage (V OC ) deficiency due to the presence of intrinsic defects and defect clusters in the bulk of CZTSSe absorber films. The doping of extrinsic cation to the CZTSSe matrix was adopted as an effective strategy to ameliorate defect properties of the solar cell absorbers. Herein, a novel Se&Sb2Se3 co-selenization process was employed to introduce Sb into CZTSSe crystal lattice. The results reveal that Sb-doping plays an active role in the crystallization and grain growth of CZTSSe absorber layer. More importantly, one of the most seriously detrimental SnZn deep defect is effectively passivated, resulting in significantly reduced deep-level traps and band-tail states compared to Sb free devices. As a result, the power conversion efficiency of CZTSSe solar cell is increased significantly from 9.17% to 11.75%, with a V OC especially enlarged to 505 mV from 449 mV. This insight provides a deeper understanding for engineering the harmful Sn-related deep defects for future high-efficiency CZTSSe photovoltaic devices.

Modelling Interfaces in Thin-Film Photovoltaic Devices.

Developing effective device architectures for energy technologies-such as solar cells, rechargeable batteries or fuel cells-does not only depend on the performance of a single material, but on the performance of multiple materials working together. A key part of this is understanding the behaviour at the interfaces between these materials. In the context of a solar cell, efficient charge transport across the interface is a pre-requisite for devices with high conversion efficiencies. There are several methods that can be used to simulate interfaces, each with an in-built set of approximations, limitations and length-scales. These methods range from those that consider only composition (e.g. data-driven approaches) to continuum device models (e.g. drift-diffusion models using the Poisson equation) and ab-initio atomistic models (developed using e.g. density functional theory). Here we present an introduction to interface models at various levels of theory, highlighting the capabilities and limitations of each. In addition, we discuss several of the various physical and chemical processes at a heterojunction interface, highlighting the complex nature of the problem and the challenges it presents for theory and simulation.

Effect of Metal-Precursor Stacking Order on Volume-Defect Formation in CZTSSe Thin Film: Formation Mechanism of Blisters and Nanopores.

In this study, we investigated the effect of the stacking order of metal precursors on the formation of volume defects, such as blisters and nanopores, in CZTSSe thin-film solar cells. We fabricated CZTSSe thin films using three types of metal-precursor combinations, namely, Zn/Cu/Sn/Mo, Cu/Zn/Sn/Mo, and Sn/Cu/Zn/Mo, and studied the blister formation. The blister-formation mechanism was based on the delamination model, taking into consideration the compressive stress and adhesion properties. A compressive stress could be induced during the preferential formation of a ZnSSe shell. Under this stress, the adhesion between the ZnSSe film and the Mo substrate could be maintained by the surface tension of a metallic liquid phase with good wettability, or by the functioning of ZnSSe pillars as anchors, depending on the type of metal precursor used. Additionally, the nanopore formation near the back-contact side was found to be induced by the columnar microstructure of the metal precursor with the Cu/Zn/Mo stacking order and its dezincification. Based on the two volume-defect-formation mechanisms proposed herein, further development of volume-defect-formation suppression technology is expected to be made.

Ge Bidirectional Diffusion to Simultaneously Engineer Back Interface and Bulk Defects in the Absorber for Efficient CZTSSe Solar Cells.

Aiming at a large open-circuit voltage (VOC ) deficit in Cu2 ZnSn(S,Se)4 (CZTSSe) solar cells, a new and effective strategy to simultaneously regulate the back interface and restrain bulk defects of CZTSSe absorbers is developed by directly introducing a thin GeO2 layer on Mo substrates. Power conversion efficiency (power-to-efficiency) as high as 13.14% with a VOC of 547 mV is achieved for the champion device, which presents a certified efficiency of 12.8% (aperture area: 0.25667 cm2 ). Further investigation reveals that Ge bidirectional diffusion simultaneously occurs toward the CZTSSe absorber and MoSe2 layer at the back interface while being selenized. That is, some Ge element from the GeO2 diffuses into the CZTSSe absorber layer to afford Ge-doped absorbers, which can significantly reduce the defect density and band tailing, and facilitate quasi-Fermi level split by relatively higher hole concentration. Meanwhile, a small amount of Ge element also participates in the formation of MoSe2 at the back interface, thus enhancing the work function of MoSe2 and effectively separating photoinduced carriers. This work highlights the synergistic effect of Ge element toward the bulk absorber and the back interface and also provides an easy-handling way to achieve high-performance CZTSSe solar cells.