Carbon-Enhanced Hydrated Salt Phase Change Materials for Thermal Management Applications.

Inorganic hydrated salt phase change materials (PCMs) hold promise for improving the energy conversion efficiency of thermal systems and facilitating the exploration of renewable thermal energy. Hydrated salts, however, often suffer from low thermal conductivity, supercooling, phase separation, leakage and poor solar absorptance. In recent years, compounding hydrated salts with functional carbon materials has emerged as a promising way to overcome these shortcomings and meet the application demands. This work reviews the recent progress in preparing carbon-enhanced hydrated salt phase change composites for thermal management applications. The intrinsic properties of hydrated salts and their shortcomings are firstly introduced. Then, the advantages of various carbon materials and general approaches for preparing carbon-enhanced hydrated salt PCM composites are briefly described. By introducing representative PCM composites loaded with carbon nanotubes, carbon fibers, graphene oxide, graphene, expanded graphite, biochar, activated carbon and multifunctional carbon, the ways that one-dimensional, two-dimensional, three-dimensional and hybrid carbon materials enhance the comprehensive thermophysical properties of hydrated salts and affect their phase change behavior is systematically discussed. Through analyzing the enhancement effects of different carbon fillers, the rationale for achieving the optimal performance of the PCM composites, including both thermal conductivity and phase change stability, is summarized. Regarding the applications of carbon-enhanced hydrate salt composites, their use for the thermal management of electronic devices, buildings and the human body is highlighted. Finally, research challenges for further improving the overall thermophysical properties of carbon-enhanced hydrated salt PCMs and pushing towards practical applications and potential research directions are discussed. It is expected that this timely review could provide valuable guidelines for the further development of carbon-enhanced hydrated salt composites and stimulate concerted research efforts from diverse communities to promote the widespread applications of high-performance PCM composites.

Preparation and Characterization of Graphite-SiO2 Composites for Thermal Storage Cement-Based Materials.

Thermal storage cement-based materials, formed by integrating phase change materials into cementitious materials, exhibit significant potential as energy storage materials. However, poor thermal conductivity severely limits the development and application of these materials. In this study, an amorphous SiO2 shell is encapsulated on a graphite surface to create a novel thermally modified admixture (C@SiO2). This material exhibits excellent thermal conductivity, and the surface-encapsulated amorphous SiO2 enhances its bond with cement. Further, C@SiO2 was added to the thermal storage cement-based materials at different volume ratios. The effects of C@SiO2 were evaluated by measuring the fluidity, thermal conductivity, phase change properties, temperature change, and compressive strength of various thermal storage cement-based materials. The results indicate that the newly designed thermal storage cement-based material with 10 vol% C@SiO2 increases the thermal conductivity coefficient by 63.6% and the latent heat of phase transition by 11.2% compared to common thermal storage cement-based materials. Moreover, C@SiO2 does not significantly impact the fluidity and compressive strength of the thermal storage cement-based material. This study suggests that C@SiO2 is a promising additive for enhancing thermal conductivity in thermal storage cement-based materials. The newly designed thermal storage cement-based material with 10 vol% C@SiO2 is a promising candidate for energy storage applications.

Leakage Proof, Flame-Retardant, and Electromagnetic Shield Wood Morphology Genetic Composite Phase Change Materials for Solar Thermal Energy Harvesting.

Phase change materials (PCMs) offer a promising solution to address the challenges posed by intermittency and fluctuations in solar thermal utilization. However, for organic solid-liquid PCMs, issues such as leakage, low thermal conductivity, lack of efficient solar-thermal media, and flammability have constrained their broad applications. Herein, we present an innovative class of versatile composite phase change materials (CPCMs) developed through a facile and environmentally friendly synthesis approach, leveraging the inherent anisotropy and unidirectional porosity of wood aerogel (nanowood) to support polyethylene glycol (PEG). The wood modification process involves the incorporation of phytic acid (PA) and MXene hybrid structure through an evaporation-induced assembly method, which could impart non-leaking PEG filling while concurrently facilitating thermal conduction, light absorption, and flame-retardant. Consequently, the as-prepared wood-based CPCMs showcase enhanced thermal conductivity (0.82 W m-1 K-1, about 4.6 times than PEG) as well as high latent heat of 135.5 kJ kg-1 (91.5% encapsulation) with thermal durability and stability throughout at least 200 heating and cooling cycles, featuring dramatic solar-thermal conversion efficiency up to 98.58%. In addition, with the synergistic effect of phytic acid and MXene, the flame-retardant performance of the CPCMs has been significantly enhanced, showing a self-extinguishing behavior. Moreover, the excellent electromagnetic shielding of 44.45 dB was endowed to the CPCMs, relieving contemporary health hazards associated with electromagnetic waves. Overall, we capitalize on the exquisite wood cell structure with unidirectional transport inherent in the development of multifunctional CPCMs, showcasing the operational principle through a proof-of-concept prototype system.

Phase Engineered Composite Phase Change Materials for Thermal Energy Manipulation.

Phase change materials (PCMs) present a dual thermal management functionality through intrinsic thermal energy storage (TES) capabilities while maintaining a constant temperature. However, the practical application of PCMs encounters challenges, primarily stemming from their low thermal conductivity and shape-stability issues. Despite significant progress in the development of solid-solid PCMs, which offer superior shape-stability compared to their solid-liquid counterparts, they compromise TES capacity. Herein, a universal phase engineering strategy is introduced to address these challenges. The approach involves compositing solid-liquid PCM with a particulate-based conductive matrix followed by surface reaction to form a solid-solid PCM shell, resulting in a core-shell composite with enhanced thermal conductivity, high thermal storage capacity, and optimal shape-stability. The core-shell structure designed in this manner not only encapsulates the energy-rich solid-liquid PCM core but also significantly enhances TES capacity by up to 52% compared to solid-solid PCM counterparts. The phase-engineered high-performance PCMs exhibit excellent thermal management capabilities by reducing battery cell temperature by 15 °C and demonstrating durable solar-thermal-electric power generation under cloudy or no sunshine conditions. This proposed strategy holds promise for extending to other functional PCMs, offering a compelling avenue for the development of high-performance PCMs for thermal energy applications.

Effect of Grain Structure of Gold Plating Layer on Environmental Reliability of Sintered Ag-Au Joints.

Gold-plated substrate is widely used in sintering with silver paste because of its high conductivity, stability, and corrosion resistance. However, due to massive interdiffusion between Ag and Au atoms, it is challenging for sintered Ag-Au joints to maintain high reliability. In order to study the effect of grain structure of gold plating layer on the environmental reliability of sintered Ag-Au joints, we prepared four substrates with different gold structures. In addition to the original gold structure (Au substrate), other gold structures were obtained by heat treatment at temperatures of 150 °C (Au-150 substrate), 250 °C (Au-250 substrate), and 350 °C (Au-350 substrate) for 1 h. Compared with the other three gold substrates, the sinter jointed on the Au-350 substrate obtained the highest shear strength. By analyzing the grain structure of the gold plating layer, it is found that the average grain size of the Au-350 substrate is the largest, and the proportion of low-angle grain boundaries is less. Few grain boundaries have a positive impact on inhibiting the excessive diffusion of Ag atoms and improving the bonding performance of the joint. Based on the above study, we further evaluated the environmental reliability of sintered joints. In 150 °C high-thermal storage, the interdiffusion of Ag and Au in the sintered joint on the Au-350 substrate was restricted, retaining stronger bonding until 200 h. In a hygrothermal environment of 85 °C/85% RH, the shear strength of the sintered Ag-Au joint with the Au-350 substrate maintained above 40.2 MPa during 100 h aging. The results indicated that the sintered Ag-Au joint on the Au-350 substrate with the largest grain size has superior high thermal reliability and hygrothermal reliability.

Investigation on the Initial Stage of the Dehydration Process in Mg(OH)2 by Density Functional Theory Calculations.

Mg(OH)2/MgO has been attracting considerable interest as a viable candidate for thermochemical heat storage materials, particularly within the temperature range of 200-400 °C. Nonetheless, the typical dehydration temperature of Mg(OH)2, which occurs within the 300-400 °C range, needs to be reduced to enhance its effectiveness in various applications for thermal energy storage. While several studies have shown that heterospecies doping can lower the dehydration temperature, the fundamental mechanism underlying this effect still remains unclear. Here, we employed density functional theory calculations to elucidate the dehydration mechanism of Mg(OH)2, with a particular focus on the initial stage of the dehydration that determines the temperature beginning the reaction. Our findings indicate that the formation of water molecules on the (001) surface is critical in the early stages of the dehydration. This discovery provides a comprehensive explanation for the role of dopants (Na, Li, or LiCl) in reducing the dehydration temperature by decreasing the formation energy of paired H and OH defects and the migration barrier of H on the surface. The present study will significantly advance the development of novel dopants for Mg(OH)2, facilitating a lower dehydration temperature and, thereby, increasing its suitability for heat storage applications.

Highly Reactive Graphene Dispersant and Its Effective Reinforcement for Phase Change Coatings.

High efficient dispersant that meanwhile possesses additional functions is highly desirable for the fabrication of graphene-based composite. In this paper, a new reactive dispersant, multi-silanols grafted naphthalenediamine (MSiND), is synthesized, which shows superiority compared with conventional dispersants. It can not only stabilize graphene in water at a high concentration of up to 16 mg mL-1, but also simultaneously be applicable for ethanol medium, in which the graphene concentration can be as high as 12 mg mL-1 at the weight ratio of 1:1 (MSiND:graphene). The dispersion is compatible with multi-matrixes and affinity to various substrates. In addition, MSiND exhibits excellent reactivity due to the existence of high-density silanol groups. Tough graphene coatings are constructed on glass slides and non-woven fabric simply by direct painting and dip-coating. Moreover, with the assistance of MSiND, graphene-doped phase-change coatings on hydrophobic non-woven fabric (e.g., functional mask) are prepared via the spray method. The composite coatings show enhanced mechanical strength and excellent energy storage performance, exhibiting great potential in heat preservation and thermotherapy.

Experimental investigation of modified indirect solar dryer with integrated thermal storage material for drying of dhekia (Diplazium esculentum) fern.

Food product drying is a crucial stage in the preservation of crops and agricultural by-products that are used as raw materials for numerous end applications. The novelty of the study is the application of a phase change material in a solar dryer to improve the effectiveness of drying and reducing the overall drying period for drying while retaining/improving the quality parameters of the dried dhekia (Diplazium esculentum). The modified indirect thermal storage integrated solar dryer made up of a single-pass solar collector is attached with the drying chamber of 16.5 kg capacity. A thermal energy storage system prepared with paraffin wax embedded inside the drying cabinet was used. The proposed solar dryer has a thermal efficiency that is 11 ± 0.2% greater than the conventionally constructed solar dryer and reduces drying time by 40 ± 2.1%. Drying kinetic analysis of dhekia was performed, and two new drying kinetic models were proposed to predict moisture ratio. From statistical analysis, it was found that the chi square value and root mean square error value fits well for the proposed models. The anti-oxidant, total phenolic content, and total flavonoid content values of samples dried in solar dryer exhibit better results compared to fresh, tray dried, and open sun-dried samples. The developed dryer shows better results in saving drying time and quality of the product. Due to its affordability and long-term solution for drying fresh farm goods, this dryer can be very helpful to small-scale farmers.

Double Carbon Networks Reinforce the Thermal Storage and Thermal Transfer Properties of 1-Octadecanol Phase Change Materials.

Using thermal storage materials with excellent thermal properties in the energy utilization system enables efficient use of renewable energy sources. Organic phase change materials (PCMs) have the advantages of high heat storage density, no corrosion, and low cost, but low thermal conductivity and insufficient heat transfer capacity have always been the bottlenecks in their application. In this paper, melamine foam@ reduction graphene oxide (MF@rGO) and carbon foam@ reduction graphene oxide (CF@rGO) composite foams with double carbon networks were prepared by self-assembly method and further employed in 1-octadecinal (OD) PCMs. The microstructure, chemical composition, phase change behavior, thermal conductivity, and photothermal conversion performance of MF@rGO/OD and CF@rGO/OD were studied in detail using SEM, FTIR, Raman DSC, and LFA. The melting and solidification enthalpies of CF@rGO/OD composite PCMs were 208.3 J/g and 191.4 J/g, respectively, its thermal conductivity increased to 1.54 W/m·K, which is 6.42 times that of pure OD. The porous structure and high thermal conductivity of the double carbon network substantially enhance the efficiency of energy storage and release in composite PCMs. CF@rGO/OD composite PCMs have excellent heat storage performance and heat transfer capacity, and a wide range of application prospects in the fields of low-temperature solar heat storage, precision instrument temperature control, and intelligent buildings.

Preparation and Performance of Ferric-Rich Bauxite-Tailing-Based Thermal Storage Ceramics.

In recent years, regenerative thermal oxidizer (RTO) has been widely used in the petroleum industry, chemical industry, etc. The massive storage required by solid waste has become a serious problem. Due to their chemical composition, bauxite tailings as raw materials for high-temperature thermal storage ceramics show enormous potential in the fields of research and application. In this study, we propose a method for preparing ferric-rich and high specific storage capacity by adding Fe2O3 powder to bauxite tailings. Based on a 7:3 mass ratio of bauxite tailings to lepidolite, Fe2O3 powder with different mass fractions (7 wt%, 15 wt%, 20 wt%, 30 wt%, and 40 wt%) was added to the ceramic material to improve the physical properties and thermal storage capacity of thermal storage ceramics. The results showed that ferric-rich thermal storage ceramics with optimal performance were obtained by holding them at a sintering temperature of 1000 °C for 2 h. When the Fe2O3 content was 15 wt%, the bulk density of the thermal storage ceramic reached 2.53 g/cm3, the compressive strength was 120.81 MPa, and the specific heat capacity was 1.06 J/(g·K). This study has practical guidance significance in the preparation of high thermal storage ceramics at low temperatures and low costs.

A Review of Solar-Coupled Phase Change Materials in Buildings.

Buildings use a significant percentage of the total energy consumed worldwide. Striving for energy conservation within buildings is of prime concern for researchers. Hence, scientists are aggressively exploring new energy storage and supply methods to reduce exorbitantly fluctuating energy demands and increase the share of renewable energy in building energy consumption. Solar systems that incorporate phase change materials (PCMs) for thermal storage have significant potential to serve in this context. These systems are not yet able to endure the significant energy demands, but they are being continually improved. The aim of this paper is to explore the existing solar PCM systems that are being studied or that are installed for use in indoor heating/cooling. As per the outcome of this systematic review, it has been observed that when coupled with solar thermal energy, the configuration of PCMs can either use passive or active techniques. Passive techniques are usually less efficient and more costly to implement in a building structure, resulting in active heat exchangers being widely implemented with better technical and economic results. At the same time, it has been observed that for most domestic buildings, organic PCMs with phase change temperatures of up to 42 °C and thermal conductivities of up to 0.56 W/m.K are most suitable for integration in solar thermal energy production. Hybrid systems are also commonly used for larger commercial buildings, in which the solar PCM system (SPCMS) provides a fraction of the total load. Additionally, the Stefan number is the most common technical parameter that is used to assess this performance, along with the effective thermal conductivity of the PCM after using enhancement techniques. The key economic indicator is annual savings per year, with most SPCMSs having a payback period of between 6 to 30 years. This review provides designers and researchers with key insights in terms of formulating a basis in the domain of coupling PCMs with solar thermal energy, especially within non-industrial buildings.

Experimental investigation and energy-exergy-environmental-economic analysis of modified indirect solar dual collector dryer while drying myrobalan slices.

The paper presents the performance evaluation of a modified indirect solar dual collector dryer (MIS2CD) integrated with a thermal storage system for drying myrobalan slices. The design of the solar collector and solar collector with thermal storage was to supply uninterrupted thermal energy to the drying chamber during sunny and sunset hours. To evaluate the dryer performances, one lot (20 kg) of myrobalan was dried in the MIS2CD, and as a result, the thermal efficiency and energy supply period of MIS2CD increased by 12 ± 02% and 41 ± 1.2%, respectively. Drying characteristics of myrobalan slices in MIS2CD, TD, and OSD were studied and compared. A two-term exponential model best explains the drying kinetics of myrobalan slices dried in MIS2CD. The dried sample in MIS2CD results in lesser ΔE* values than TD and OSD methods. The highest exergy efficiency of 78.2% and lower exergy losses were recorded. The energy payback period of the MIS2CD was evaluated as 1.42 years. The CO2 emitted and CO2 reduced reduction are calculated for drying myrobalan in MIS2CD for a lifetime (20 years) of 67.85 kg and 20.65 tons, respectively. The capital cost of the solar dryer design was estimated depending on the economic considerations of the state. The drying hours were increased in MIS2CD against OSD by 59% on the annual sunny days (210 days). The sample drying period MSD and TD to reach the final moisture level of 7% was 9 h and 5 h, respectively. The total economic benefit is 22,622 INR (annually), and the 2.08 benefit-cost ratio for myrobalan dried in MIS2CD compared to TD. The MIS2CD's payback period is nearly 2.18 years, much less than the dryer's lifetime.

Development and characterization of a quaternary nitrate based molten salt heat transfer fluid for concentrated solar power plant.

Over the past few years, there has been growing interest in using inorganic quaternary nitrate-based molten salt mixtures as a highly effective heat transfer fluid (HTF) for concentrated power plants, primarily because they can achieve low melting temperatures. However, the high viscosity of these salt mixtures is still a significant challenge that hinders their widespread adoption. The high viscosity leads to high pumping power requirements, which increases operational costs, and reduces the efficiency of the Rankine cycle. To address this challenge, this study developed and characterized a novel quaternary molten salt, focusing on the effect of LiNO3 additions on the salt's viscosity, thermal conductivity, melting point temperature, heat capacity, and thermal stability. The quaternary mixture comprised KNO3, LiNO3, Ca(NO3)2, and NaNO2, with varying percentages of each salt. The study utilized various standard techniques to examine the characteristics of the developed mixture. Results showed that increasing LiNO3 content led to a decrease in melting temperature, higher heat capacity, improved thermal stability, conductivity, and reduced viscosity at solidification temperature. The lowest endothermic peak for the new mixture emerged at 73.5 °C, which is significantly lower than that of commercial Hitec and Hitec XL, indicating better potential for use as a heat transfer fluid for concentrated solar thermal power plant applications. Furthermore, the thermal stability results showed high stability up to 590 °C for all the samples examined. Overall, the new quaternary molten salt shows promise as a potential replacement for current organic synthetic oil, offering a more efficient solution.

Spent Yeast-Derived 3D Porous Carbon Skeleton as Low-Cost D-Mannitol Supporting Material for Medium Temperature Thermal Energy Storage.

Shape-stable phase change materials (ss-PCMs) are extensively applied in renewable energy storage. The core for realizing high latent heat and good thermal stability of ss-PCMs is the designation of suitable supporting skeletons that can effectively preserve the PCMs from leaking out. In this study, ss-PCMs impregnated by D-mannitol were prepared using a waste yeast-derived carbon (YC) as the support material. YC possesses a large surface area (669.90 m2/g), which can provide sufficient phase transition space and nucleation sites for D-mannitol. The results indicated that a reduced supercooling of 44.76 °C for YC/D-mannitol ss-PCMs can be realized. The ss-PCMs also exhibited good cycling stability, with latent heat loss rates of 4.00% and 2.15% after 200 thermal cycles. We further demonstrate that YC provides restricted space for mannitol to inhibit the supercooling mechanism. The YC/D-mannitol ss-PCMs exhibited great promise for solar heat storage and industrial waste heat recovery in the medium temperature domain.

Performance evaluation of external compound parabolic concentrator integrated with thermal storage tank for domestic solar refrigeration system.

The aim of this research was to develop a model for a solar refrigeration system (SRS) that utilizes an External Compound Parabolic Collector and a thermal energy storage system (TESS) for solar water heating in Chennai, India. The system parameters were optimized using TRNSYS software by varying factors such as collector area, mass flow rate of heat transfer fluid, and storage system volume and height. The resulting optimized system was found to meet 80% of hot water requirements for the application on an annual basis, with an annual collector energy efficiency of 58% and an annual TESS exergy efficiency of 64% for a discharge period of 6 h per day. In addition, the thermal performance of 3.5 kW SRS was studied by connecting it to an optimized solar water heating system (SWHS). The system was found to generate an average cooling energy of 12.26 MJ/h annually, with a coefficient of performance of 0.59. By demonstrating the ability to efficiently generate both hot water and cooling energy, the results of this study indicate the potential for utilizing a SWHS in combination with STST and SRS. The optimization of system parameters and the use of exergy analysis provide valuable insights into the thermal behavior and performance of the system, which can inform future designs and improve the overall efficiency of similar systems.

Development of FE modeling for hybrid greenhouse dryer for potato chips drying.

In this communication, a combination of heat and mass transfer model was developed using finite element (FE) model to explain the drying performance of the hybrid greenhouse dryer for potato chips. The hybrid greenhouse dryer is integrated with a single-pass solar air heater (SAH). A partial differential equation for a combined set of heat and mass transfer was numerically solved by the FE method. In order to see the spatial moisture distribution within the potato sample, a 3-dimensional FE model was created, and moisture removal takes place from the surface during drying of the products. Lagrange triangle FEs of extremely small size and second-order geometry shape were employed for meshing the geometry of model. Time-dependent study was express the fluctuation in time interval of 0-5 h. The developed model showed the maximum crop and ground temperature are 67.1 and 79.1°C, respectively. Moisture ratio in dry basis is reduced from 1 to 0.005 in 03 h and remains constant at 0.005. Thus, average moisture ratio in dry basis was found as 0.18902. Drying efficiency for the hybrid greenhouse dryer found to be 20.52%, whereas thermal efficiency for SAH was found 54.53%. Relative humidity inside the drying chamber found to be 26.50% in hybrid greenhouse dryer. The predicted versus the experimental results observed that hybrid greenhouse dryer having moderate inside temperature is suitable for crop drying as well as ith sustaining the environmental balance, hybrid greenhouse proves to be most effective.

Drying kinetics and thermo-economic analysis of drying hot water blanched ginger rhizomes in a hybrid composite solar dryer with heat exchanger.

This research aimed to examine the need of adding hot water blanching pre-treatment on the drying of ginger rhizomes using a hybrid solar-dryer with paraffin liquid as thermal storage infused into a copper tube to form a compact heat exchanger. Blanching duration quickened the drying rate of the ginger rhizomes and the average drying rate for blanching at 90 s, 60 s, 30 s and un-blanched ginger varied between 0.0147 kg/h to 0.0245 kg/h at a sensible heat ratio of 4.12 × 10-5 to 2.53 × 10-3. The optimal drying rate varied from 0.01161 kg/h to 0.0263 kg/h for all treatment at a collector temperature range of 39.5 °C-40.5 °C and collector efficiency range of 14.3%-30%. The logarithmic model better predicted the drying kinetics of un-blanched and blanching for 30 s with an R2 value of 0.9875 and 0.97247 respectively while the modified Henderson and Pabis model better predicted drying of blanched ginger rhizomes at 60 s and 90 s with R2 values of 0.96252 and 0.98188 respectively. Using the hybrid solar dryer instead of artificial dryers with fossil energy sources can save about $75.731 to $757.31 of the running cost as the usage increased from 10 to 100%. The payback period decreased from 2.88 years to 0.31 years as the rate of usage increased from 10 to 100%. Using the presented solar dryer instead of coal, diesel or grid base electricity can prevent 15.96 to 186, 7.62 tones of CO2 from entering the atmosphere. The earned carbon credit if the dryer is to be powered by coal, diesel or grid base electricity were $ $6245364, $27080.52, and $231.45 per year respectively which can be used to compensate other non-renewable energy sources deployed within an energy enterprise.

Cooking performance assessment of a phase change material integrated hot box cooker.

Previous research on solar box cookers focusing on the bulk usage of energy storage materials is a costly technique for performance enhancement. Bulk energy storage materials take much time to charge and, thus, result in a low rate of cooking at the start. Therefore, a hot box solar cooker has been developed and experimentally studied for thermal performance enhancement in a hilly region of Uttarakhand, India. A bed of phase change material (paraffin wax) filled with small capsule-shaped containers was prepared (detachable) and placed over the cooking tray of the tested cooker. These containers were vertically positioned over the bed to enhance the heat transfer rate inside the cooker to attain a fast-cooking response. Notably, the combined effect of extended geometry with PCM is an excellent method to increase the efficiency of a solar cooker. As per the author's knowledge, likely techniques have not been studied for a box cooker to achieve a fast-cooking rate in any hilly region up to date. The results of cooking tests show that the cooking plate attained a maximum temperature of about 150 °C. It is because of the combined effect of extended fins (vertical capsules) and PCM filled inside them. The results of the experimental study show that the thermal efficiency of the cooker was found to be about 45.7%, the cooking power was calculated about 54.71 W, the heat transfer coefficient was estimated about 311 W/m2 °C, and the overall heat loss coefficient was computed about 5.71 W/m2 °C. This modified cooker costs about $48.19, and the payback period is about 03 years and 11 months. Cooking trials also showed that the present SBC could cook almost all the dishes commonly cooked in Uttarakhand.

Drying kinetics and economic analysis of bitter gourd flakes drying inside hybrid greenhouse dryer.

In this study, a heat storage-based hybrid greenhouse dryer has been developed and analysed for drying bitter gourd flakes under the climatic condition of Ranchi, India. Proposed heat storage-based hybrid greenhouse dryer consists of a solar air heater with a 2.12-m2 area, greenhouse dryer and DC fan to induce and force the air. The significant objective of the present study is to analyse the drying efficiency, drying kinetics, property analysis, economic analysis, embodied energy and CO2 mitigation of the hybrid greenhouse dryer for drying of bitter gourd flakes. An experiment was performed simultaneously on proposed system and open sun drying for the proper comparative analysis. Moisture contents reduced from 88.14 to 10.14% in 6 h in proposed dryer and 88.14 to 11.01% in 15 h for open system. Thus, significant drying time is reduced in proposed system by 8 h as compared to open system. Environmental impact analysis shows that the energy payback time was found to be 0.4907 years only. Cost of the proposed system dryer is 22664.30 INR. The total embodied energy is found 1591.07 kWh and earned carbon credit ranges from 16844.76 to 67379.05 INR, while CO2 mitigation was 46.28 tonnes for 35 years of expected lifetime. Seven standard mathematical models for drying of bitter gourd flakes were studied. Ahmad and Prakash model was found to be the best as compared to other models. The metal contents of dried bitter gourd flakes were also examined. Bitter gourd dried in proposed dryers possesses superior metal content as compared to open systems. Impact analysis demonstrates that the hybrid greenhouse dryer is more suitable for reducing post-harvest loss with environmental sustainability.

Experimental study on the single basin solar still integrated with shell and spiral finned tube latent heat storage system enhanced by copper oxide nanoparticles.

In this work, a latent heat storage system was designed, installed, and tested when it was integrated with a single basin solar still. The latent heat storage system is a shell and spiral finned tubes, where 20 kg of a paraffin-CuO nanocomposite with a weight fraction concentration of 1% was poured into the shell while hot water from the solar collector was being pumped through the spiral finned tubes. In order to identify the effect of implementing the storage system on the performance of the solar still, two experiments were conducted, with and without storage, under approximatelysimilar weather conditions. The proposed design of the storage system succeeded to overcome all challenges associated with using paraffin wax as storage material with the solar still. The obtained results revealed that an improvement in fresh water daily productivity of 4.54% was achieved when the storage system was integrated with the solar still. The economic analysis showed that the cost per 1 L of fresh water was 0.25 $/L when the storage unit was used. This high cost will be significantly reduced when a large-scale system is installed.