A review of the latest developments in rotary NiTi technology and root canal preparation.

The introduction of nickel-titanium (NiTi) mechanical instruments dramatically changed clinical endodontics over the last few decades. Before NiTi, it was necessary to use more instruments to create an ideal root canal shape, and many approaches, sequences and techniques were developed over the years. Recently, NiTi endodontic instruments have undergone a series of changes brought about by modifications in design, surface treatments, and thermal treatments to improve their root canal preparation outcomes and reduce associated canal preparation risks during root canal treatment. Heat treatment is one of the most fundamental approaches to improving the fatigue resistance and flexibility of NiTi endodontic instruments. In addition, new kinematics have been developed to offer greater safety and efficiency. This narrative review describes the general properties and manufacturing of NiTi instruments, and the mechanical system evolution of NiTi instruments.

Phase transformation and mechanical properties of heat-treated nickel-titanium rotary endodontic instruments at room and body temperatures.

BACKGROUND: The aim of this study was to evaluate the phase composition, phase transformation temperatures, bending property, and cyclic fatigue resistance of different heat-treated nickel-titanium (NiTi) rotary instruments with the same tip diameter and taper at room (RT; 25 ± 1 °C) and body (BT; 37 ± 1 °C) temperatures. METHODS: Five heat-treated NiTi rotary instruments, HyFlex EDM (EDM), HyFlex CM (CM), Vortex Blue (VB), RE file CT (RE) and JIZAI, and a non-heat-treated NiTi rotary instrument (Mtwo) with a size 40, 0.04 taper were investigated. Temperature-dependent phase transformation was examined with differential scanning calorimetry (DSC). The bending loads of the instruments at RT and BT were evaluated using a cantilever-bending test. Cyclic fatigue resistance at RT and BT was measured using a dynamic test, during which the instruments were rotated in combination with a 2-mm back-and-forth motion in an artificial curved canal, and the number of cycles to failure (NCF) was determined. The results were analyzed using two-way repeated measures analysis of variance, a simple main effect test, and the Bonferroni test (α = 0.05). RESULTS: DSC results indicated that EDM and Mtwo were primarily composed of martensite/R-phase and austenite, respectively, while the other heat-treated instruments were composed of a mix of martensite/R-phase and austenite at the tested temperatures. Regardless of the temperature setting, the bending loads of heat-treated instruments were significantly lower than those of Mtwo (p < 0.05). EDM showed the lowest bending loads and highest NCF at both temperatures (p < 0.05). CM, VB, and JIZAI showed significantly higher bending loads at BT than at RT (p < 0.05). The NCF of all the heat-treated instruments, except VB, was lower at BT than at RT (p < 0.05). At BT, the NCF of CM, VB, RE, and JIZAI were not significantly higher than that of Mtwo (p > 0.05). CONCLUSIONS: Heat-treated NiTi instruments exhibited lower bending loads and higher NCF values than Mtwo. However, this tendency was less pronounced at BT than at RT, especially in the NCF values of instruments with a mixture of martensite/R-phase and austenite phases at the tested temperatures.

Characterization of four heat-treated reciprocating instruments: Design, metallurgy, mechanical performance, and irrigation flow patterns.

AIM: To compare the design, metallurgy, and mechanical properties of four heat-treated reciprocating instruments coupled with the evaluation of the irrigation flow using an in silico model. METHODOLOGY: New EdgeOne Fire Primary, Easy-File Flex Regular 25, WaveOne Gold Primary and Reciproc Blue R25 instruments (n = 124) were initially evaluated regarding their design through stereomicroscopy, scanning electron microscopy and 3D surface scanning. In addition, energy-dispersive X-ray spectroscopy was utilized to determine their elemental composition, and differential scanning calorimetry tests to evaluate their phase transformation temperatures. Their mechanical performance was further assessed through torsional and bending tests. Using scans obtained from a real tooth and the instruments, a computational fluid dynamics assessment was conducted to determine the irrigation flow pattern, apical pressure, and wall shear stress in simulated canal preparation. Mood's median and One-way anova post hoc Tukey tests were used for statistical comparisons (α = 5%). RESULTS: Reciproc Blue exhibited a superior number of blades (n = 8), whereas EdgeOne Fire had the highest overall volume (4.38 mm3 ) and surface area (32.32 mm2 ). At the 3-mm axial level, EdgeOne Fire displayed the lowest core diameter (0.13 mm), while Reciproc Blue had the highest (0.16 mm). All blades were symmetrical, and the tips of the instruments were non-active but differed from each other. The most irregular surfaces were observed in EdgeOne Fire and Easy-File Flex. All instruments were manufactured from nickel-titanium alloys and exhibited distinct phase transformation temperatures. WaveOne Gold and Reciproc Blue demonstrated the highest maximum torque values (1.87 and 1.62 N cm, respectively), while the lowest was observed on EdgeOne Fire (1.21 N cm) (p < .05). The most flexible (p < .05) were EdgeOne Fire (angle of rotation: 602.6°; maximum bending load: 251.4 g.f) and Reciproc Blue (533.2° and 235.6 g.f). There were no significant differences observed in the irrigation flow among the four domains generated by the tested instruments. CONCLUSIONS: Despite observing variations in the design, phase transformation temperatures, and in the torsional and bending test outcomes among the four heat-treated reciprocating instruments, no significant differences were found in the irrigation flow pattern among the different groups in the simulated root canal preparations.

Influence of sodium hypochlorite on cyclic fatigue resistance of nickel-titanium instruments: A systematic review and meta-analysis of in vitro studies.

OBJECTIVE: This systematic review/meta-analysis investigated the influence of NaOCl on cyclic fatigue resistance of endodontic NiTi instruments. MATERIALS AND METHODS: A systematic search until July 2022 in PubMed/MEDLINE, Embase, Scopus, Web of Science, SciELO, Cochrane Library, and grey literature was conducted. According to the PECOS strategy, only in vitro studies evaluating the effects of NaOCl on the cyclic fatigue resistance of NiTi instruments were eligible. Cyclic fatigue resistance was the primary outcome. A modified Joanna Briggs Institute's Checklist was used for risk of bias assessment. RESULTS: Of the 2,445 records screened, 37 studies were included. Most studies used simulated canals made of stainless-steel block with severe to moderate curvatures. NaOCl concentration varied from 1-6%, mainly at 37 °C. Regarding fatigue resistance, 23 studies using 1.2% to 6% NaOCl showed a reduction in the resistance compared to the control groups, especially when pre-heated. Four meta-analyses were performed according to the tested NiTi systems. The meta-analyses indicated that the PTU F2 files had higher reduction of fatigue resistance after exposure to 5.25% NaOCl; no differences between NaOCl and no immersion were observed for Reciproc R25, WaveOne 25.08, and WaveOne Gold Primary files. Included studies had low risk of bias. CONCLUSION: NaOCl appears to reduce cyclic fatigue resistance of certain NiTi files, especially when they are pre-heated, particularly in conventional NiTi files compared to some heat-treated instruments. It is possible that the temperature of the solution may have a greater influence on resistance than NaOCl itself. Important to note that an overall tendency toward no significant influence was observed among various systems. CLINICAL RELEVANCE: Precautions are necessary when a pre-heated high-concentration NaOCl is used to enhance its properties during root canal preparation, mainly using conventional wire.

Smoothness provided by a one-step finishing and polishing system and its maintenance after 12-month aging.

PURPOSE: To evaluate the smoothness provided by a one-step finishing and polishing system and its maintenance after hydrothermal aging and brushing of a nanofilled resin composite. METHODS: 96 samples of the nanofilled composite Filtek Z350 XT were fabricated, which, after initial average roughness (Ra) analysis, were randomly distributed into three groups, according to the selected finishing and polishing system. The multi-step systems Sof-Lex (aluminum oxide discs) and Jiffy (bullet-shaped abrasive rubbers), and the one-step system OneGloss (bullet-shaped abrasive rubber) were used. After finishing and polishing, a new Ra measurement was performed, and then half of the samples from each group were stored in artificial saliva for 12 months, while the other half underwent aging processes associating hydrothermal cycles (10,000 cycles at 5-55°C) followed by brushing (5,500 strokes), with a mid-abrasive (Crest Cavity Protection) dentifrice slurry, simulating a 12-month period in the oral cavity. Final Ra measurements were performed, and data were analyzed by generalized linear model and Tukey's test (α= 5%). RESULTS: There was interaction between finishing and polishing system and aging (P< 0.001). The one-step abrasive rubber point provided significantly higher Ra values compared to the multi-step systems, and with the discs there was higher smoothness than with the rubber point sequence. This result was maintained after 12 months in artificial saliva, but after hydrothermal cycles followed by brushing, one-step and multi-step abrasive rubber points no longer significantly differed from each other. Only for the one-step system, hydrothermal cycles followed by brushing significantly reduced Ra. CLINICAL SIGNIFICANCE: Although hydrothermal cycles followed by brushing may have increased the smoothness of nanofilled composite finished and polished with the one-step system, only the multi-step system provided a surface within the roughness threshold to avoid biofilm retention.

Cleaning methods for dental instruments.

It is essential to ensure that reusable dental instruments are scrupulously clean as a first step in the decontamination process. Any residual soil on the surface of equipment creates a risk that will prevent steam, generated during sterilisation, from condensing on the surface of the instrument and raising the temperature to that required to ensure sterilisation. Further, most microorganisms will struggle to attach to the surface of a clean instrument. Adherence of microorganisms to the surface of an instrument that is contaminated with organic soil or the irregular surface of residual dental materials is likely to be greatly enhanced. It is therefore important to ensure that residual dental materials are removed from the surface of instruments, at the point of use, before they are allowed to set.It is also important to ensure that the methods used to clean dental equipment do not damage the instrument. Any method that has the potential to scratch the surface of an instrument and therefore make it more difficult to clean should be avoided. Aggressive cleaning can lead to removal of the passivation layer, the chromium-rich layer that prevents corrosion occurring, formed on the surface of instruments made from stainless steel. If corrosion forms on the surface of an instrument, the surface becomes roughened and possibly stained. Surface staining can then be difficult to differentiate from other stains or marks caused by retained biological soil. Corrosion on the surface of an instrument will make the effective cleaning of the surface more difficult and therefore corroded or stained instruments should be discarded.

Reducing pain and discomfort associated with rubber dam clamp placement in children and adolescents: a systematic review and meta-analysis of effectiveness.

BACKGROUND: The application of rubber dams is a widely accepted method of tooth isolation in dental practice. Placement of the rubber dam clamp might be associated with levels of pain and discomfort, especially in younger patients. The purpose of the present systematic review is to evaluate the efficacy of the methods for reducing pain and discomfort associated with rubber dam clamp placement in children and adolescents. MATERIALS AND METHODS: English-language literature from inception until September 6th, 2022 was searched in MEDLINE (via PubMed), SCOPUS, Web of Science, Cochrane, EMBASE, and ProQuest Dissertations & Theses Database Global for articles. Randomized controlled trials (RCTs) comparing methods of reducing the pain and/or discomfort associated with rubber dam clamp placement in children and adolescents were retrieved. Risk of bias assessment was performed using a Cochrane risk of bias-2 (RoB-2) risk assessment tool and the certainty of evidence was assessed using the Grading of Recommendations Assessment, Development and Evaluation (GRADE) evidence profile. Studies were summarized and pooled estimates of pain intensity scores and incidence of pain were calculated. The meta-analysis was conducted in the following groups according to type of interventions (LA, audiovisual (AV) distraction, behavior management (BM), electronic dental anesthesia (EDA), mandibular infiltration, inferior alveolar nerve block (IANB), TA), outcome (intensity or incidence of pain), and assessment tool (face - legs - activity - cry - consolability (FLACC), color scale, sounds - motor - ocular changes, and faces pain scale (FPS)): (a) pain intensity using (LA + AV) vs (LA + BM), (b) pain intensity using EDA vs LA (c) presence or absence of pain using EDA vs LA (d) presence or absence of pain using mandibular infiltration vs IANB (e) Comparing pain intensity using TA vs placebo (f) Presence or absence of pain using TA vs placebo. Meta-analysis was conducted using StataMP software, version 17.0 (StataCorp, College Station, Texas). Restricted maximum-likelihood random effect model (REML), Mean difference (MD) with 95% confidence interval, and log odds ratio (OR) with 95% CI were calculated were calculated. RESULTS: Initially, 1452 articles were retrieved. Sixteen RCTs were finally included for reviewing and summarizing. Nine articles with a total of 867 patients were included for quantitative meta-analysis. The differences in pain intensity scores were not significant in any comparison groups (group a: [MD = -0.04 (95% CI = - 0.56, 0.47), P = 0.87, I2 = 0.00%], group b: [MD = 0.25 (95% CI = -0.08, 0.58), P = 0.14, I2 = 0.00%], group c [MD = -0.48 (95% CI = -1.41, 0.45), P = 0.31, I 2 = 0.00%], group d: [MD = -0.67 (95% CI = -3.17, 1.83), P = 0.60, I 2 = 0.00%], group e: [MD = -0.46 (95% CI = -l.08, 0.15), P = 0.14, I 2 = 90.67%], and group f: [MD = 0.61 (95% CI = -0.01, 1.23), P = 0.06, I 2 = 41.20%]. Eight studies were judged as having some concern for risk of bias and the remaining studies were considered as low risk for bias. The certainty of evidence was considered medium for all comparison groups. DISCUSSION: In the present meta-analysis, a considerable difference was obtained between the included studies regarding intervention methods and pain assessment tools and the analysis was performed in groups with small numbers of the studies. Owing to the mentioned variabilities and the small number of studies, the results of the analysis should be interpreted with caution. The indistinguishability of the manifestations of pain/discomfort from fear/anxiety, particularly in children, should also be considered while using the results of the present study. Within the limitations of the current study, no significant differences were found between the proposed methods for reducing pain and discomfort associated with rubber dam clamp placement in children and adolescents. A larger number of more homogenous studies regarding intervention methods and pain assessment tools need to be conducted in order to draw stronger conclusions. TRIAL REGISTRATION: This study was registered in PROSPERO (ID number: CRD42021274835) and research deputy of Mashhad University of Medical Sciences with ID number 4000838 ( https://research.mums.ac.ir/ ).

A critical evaluation of physical and manufacturing properties of genuine and counterfeit rotary nickel-titanium endodontic instruments.

BACKGROUND: Rotary nickel-titanium (NiTi) instruments are made to exacting standards and are costly to manufacture, and quality control is paramount. Consequently, unauthorized factories make counterfeit instruments that are less expensive and may therefore be attractive to dentists. Little information exists about the metallurgy and manufacturing quality of such instruments. There is the potential for counterfeit instruments to be at higher risk of fracture during treatment, thereby compromising clinical outcomes. The aim of this study was to evaluate physical and manufacturing properties of genuine and counterfeit ProTaper Next™ and Mtwo® rotary NiTi instruments. METHODS: This study investigated the metallurgical properties, manufacturing quality, microhardness and number of cycles to failure of two commonly used rotary NiTi systems and compared them with counterfeit products purporting to be genuine articles. RESULTS: Counterfeit instruments were found to be inferior in manufacturing standards and were less resistant to cyclic fatigue when compared to genuine instruments. CONCLUSIONS: Counterfeit rotary NiTi instruments may be less efficient at preparing root canals and may be at higher risk of fracture during endodontic treatment. Dentists must be aware that, although less expensive, counterfeit instruments may be of dubious manufacturing quality and at higher risk of fracture if used in patients. © 2023 Australian Dental Association.

Dynamic Cyclic Fatigue Resistance of Heat-treated Nickel Titanium Instruments in Reciprocating Motion.

OBJECTIVE: To compare the fatigue resistance of different heat-treated reciprocating instruments tested in a dynamic cyclic fatigue model. METHODS: Forty-eight new instruments were inspected under magnification and selected for this study, and then divided as follows (n=12): X1 Blue (MK Life, Porto Alegre, RS, Brazil), Pro-R (MK Life), Reciproc (VDW, Munich, Germany), and Reciproc Blue (VDW). Artificial canals presenting a curvature of 60° angle and 5 mm radius were milled in zirconia. The block containing the artificial canals was mounted in a container filled with water kept at 37°C. A specially designed device was used to perform controlled axial movements while the instruments were activated inside the canals. Time to failure was recorded in seconds, and fragment lengths were measured (mm). Data were analyzed statistically with the significance level set at 5% (One-Way ANOVA and Tukey test). RESULTS: Pro-R and Reciproc Blue instruments presented the highest fatigue resistance, being significantly different from the other tested files (p<0.05). Reciproc presented intermediate results, significantly different X1 Blue (p<0.05). The fractographic analysis showed typical features of cyclic fatigue for all instruments. CONCLUSION: Pro-R and Reciproc Blue instruments are more resistant to dynamic cyclic fatigue than the Reciproc and X1 Blue. (EEJ-2022-10-124).

Effect of glide path instruments in cyclic fatigue resistance of reciprocating instruments after three uses.

The present study aims to evaluate the effect of different glide path instruments on the cyclic fatigue resistance of reciprocating endodontic instruments after three uses in mandibular molars. Eighteen Wave One Gold Primary reciprocating instruments were selected and randomly divided into three groups according to the glide path instrument: G1 - manual file K #15, G2 - Wave One Glider reciprocating instrument, and G3 (control group) - glide path was not performed. The reciprocating instruments were tested on mandibular molars and subdivided into three other groups: a new instrument, an instrument with a previous single-use, and an instrument with two previous uses. After the endodontic instrumentation, the instruments were subjected to the cyclic fatigue resistance test using an appropriate tool. The data were submitted to the Shapiro-Wilk test, and subsequently the Kruskal-Wallis test with a significance level of 5%. The results showed no statistical difference between the groups. Thus, it was concluded that the creation of a glide path did not affect the cyclic fatigue resistance of the reciprocating instrument. In addition, the reuse of final preparation instruments up to two times proved to be safe since no fractures were observed in the tested instruments.

Comparative analysis of reciprocating and flat-side heat-treated rotary single-file systems: Design, metallurgical characteristics, and mechanical performance.

AIM: To compare two flat-side single-file rotary instruments with three single-file reciprocating systems through a multimethod assessment. METHODOLOGY: A total of 290 new NiTi single-file rotary (AF F One Blue 25/0.06 and Platinum V.EU 25/0.06) and reciprocating (One Files Blue R25, Reciproc Blue R25, Reciproc R25) instruments were selected, carefully examined for any major deformations, and evaluated regarding their macroscopic and microscopic design, nickel and titanium elements ratio, phase transformation temperatures, and mechanical performance (time/rotation to fracture, maximum torque, angle of rotation, microhardness, maximum bending, and buckling strengths). One-way anova post hoc Tukey, T-test, and nonparametric Mood's median tests were used for statistical comparisons (α = 5%). RESULTS: Tested instruments had identical blade counts and near-identical helical angles of approximately 24° (rotary instruments) and 151° (reciprocating instruments). The flat-side analysis revealed a few inconsistencies, such as discontinuity segments, different orientations, and gaps in the homogeneity of the bluish colour. Microscopically, flat-side instruments exhibited blade discontinuity and an incomplete S-shaped cross-section. The surface finish was smoother for One Files Blue and more irregular for both rotary instruments. There were distinct phase transformation temperatures amongst all instruments. All heat-treated instruments were in R-phase arrangement, and Reciproc was in R-phase plus austenite at test temperature (20°C). Compared with the reciprocating instruments, both flat-side instruments exhibited lower results in the cyclic fatigue tests using two different clockwise kinematics, maximum torque, angle of rotation, and maximum buckling strength (p < .05). The rotary systems also exhibited low flexibility (p < .05). AF F One Blue had the lowest microhardness, whilst Reciproc had the highest value. CONCLUSION: This multimethod investigation revealed that the flat-side rotary instruments underperformed the reciprocating instruments regarding cyclic fatigue (with two different clockwise kinematics), maximum torque, angle of rotation, maximum buckling strength, and flexibility. Manufacturing inconsistencies were also observed in some of the flat-side instruments, including discontinuity segments, different orientations, and in the homogeneity of their bluish colour given by the heat treatment.

Biofilm on and structural damage of rotary cutting instruments after 5 cycles of clinical use and processing.

BACKGROUND: Rotary cutting instruments (RCIs) are sterilized routinely. The authors aimed to analyze the structural integrity, presence of dirt, and microbial contamination of RCIs used in clinical practice after processing. METHODS: Eighty-four RCIs (42 carbide burs, 42 diamond burs) were divided into baseline, control, and test groups. The RCIs were evaluated by means of scanning electron microscopy and microbiological analysis. Evaluation criteria included presence of structural damage, dirt, biofilm, and isolated cells and their phenotypic profile. RESULTS: The carbide burs from all groups and diamond burs from the test groups had structural damage. Dirt was observed in the baseline and test groups. Three bacterial species were isolated from 4 RCIs (9.52%). An isolated cell was observed from 1 carbide bur. Biofilm was observed on 3 RCIs (7.14%). CONCLUSIONS: RCIs should not be subjected to multiple uses; after the first clinical use they accumulate structural damage and dirt that hampers the cleaning step, causing failure in the sterilization process. PRACTICAL IMPLICATIONS: The presence of microorganisms and structural damage on the RCIs confirmed that they are not amenable to processing, a fact that characterizes them as a single-use health care product.

Investigation of the efficacy of different Ni-Ti systems on acrylic blocks for correcting ledge formation.

BACKGROUND: The aim of this study was to compare the efficacy of K-type stainless steel hand instruments (Mani Inc. ), Fanta AF™ Ledge Correction (LC) (Fanta Dental), and Hyflex EDM (Coltene-Whaledent) for ledge correction, canal transport, centric ability, and shaping (preparation) time after an artificial ledge has been bypassed manually in highly curved canals using acrylic blocks. METHODS: Forty-two resin blocks, each with a radius of 5 mm (Endo Trainer Block, VDW) and an apical inclination of 55°, were used. Under stereomicroscope magnification, standard artificial ledges were created on acrylic blocks, and attempts were then made to eliminate them using hand instruments, FantaAF™ LC, and Hyflex EDM. Before and after images were obtained using a stereomicroscope and compared using Photoshop. RESULTS: Fanta AF™ LC and Hyflex EDM were found to be more effective for correcting ledges than hand instruments. The use of hand instruments resulted in the greatest transportation away from the canal curvature in the apical area. The canal shaping was completed in the shortest amount of time using Fanta AF™ LC, followed by HyFlex EDM and then the hand instruments. CONCLUSION: In terms of centric ability, the order from best to worst is as follows: Fanta AF™ LC, Hyflex EDM, and hand instruments. After the ledge was manually bypassed with hand instruments in the root canals, Hyflex EDM and Fanta AF™ LC were found to be more effective than hand instruments in reshaping the previously unreachable region between the ledge and the foramen apical.

Multimethod analysis of three rotary instruments produced by electric discharge machining technology.

AIM: This study aimed to compare three rotary instruments produced by the EDM process with the heat-treated ProTaper Gold system regarding design, metallurgy, mechanical properties and shaping ability. METHODOLOGY: HyFlex EDM (25/~), Neoniti (25/.06), EDMax (25/.06) and ProTaper Gold (25/.08v) instruments (n = 58 per group) were compared regarding design, metallurgy and mechanical performance. Unprepared canal areas were calculated for each system after preparation of mesiobuccal, mesiolingual and distal canals of mandibular molars (15 canals per group) using micro-CT technology. Statistical analyses were performed using One-way anova post-hoc Tukey and Kruskal-Wallis post-hoc Dunn's tests (α = 5%). RESULTS: All instruments had asymmetrical blades, no radial lands, no major defects and almost equiatomic nickel/titanium ratios, but different cross-section designs, tip geometries and surface appearances. Although instruments had distinct transformation temperature curves, they showed crystallographic martensitic arrangement at 21°C and mixed austenite plus R-phase at body temperature. Neoniti and HyFlex EDM showed similar results in all mechanical tests (p > .05), while EDMax and ProTaper Gold had similar time to fracture (p = .841), maximum bending load (p = .729), and cutting ability (p = .985). ProTaper Gold showed the highest torque to failure (p < .001) and HyFlex EDM had the lowest buckling resistance (p < .001). Mean percentages of unprepared canal areas ranged from 20.4% to 25.7% in the mesial canals, and from 20.8% to 26.2% in the distal canal, with no statistical differences among systems (p > .05). CONCLUSIONS: Instruments' geometry and phase transformation temperatures influenced the results of the mechanical tests, but not their shaping ability.

Effect of different retreatment files using different kinematics on the release of inflammatory mediators in root canal retreatment of single-rooted teeth: a randomized clinical trial.

OBJECTIVES: This randomized clinical trial aimed to evaluate the effect of two rotaries (ProTaper Universal Retreatment (PTUR)), D-Race (DR) + XP-Endo Finisher R (XPFR) and one reciprocating (Reciproc Blue (RB) retreatment techniques on the release of neuropeptides (Substance P, calcitonin gene-related peptide (CGRP)), and cytokines (IL-6 and IL-10) in periapical fluid in root canal retreatment of single-rooted teeth. MATERIALS AND METHODS: In this randomized clinical trial (ClinicalTrials.gov ID: NCT05039502), seventy-five patients scheduled for retreatment were randomly divided into 3 groups according to the file system used to remove root canal filling materials (n = 25): PTUR, RB, and DR + XPFR. After reshaping and disinfection of the root canals, periapical fluid samples were taken, and the levels of Substance P, CGRP, IL-6, and IL-10 were measured by enzyme-linked immunosorbent assay (ELISA) test. Data were analyzed using the Kruskal-Wallis and chi-square tests. The level of significance was set as p = 0. 05. RESULTS: All the allocated participants received the intervention and were analyzed. There was no statistically significant difference among groups in terms of gender, age, tooth localization, and the distribution of analgesic use after treatment (p values 0.799, 0.095, 0.637, 1.000, respectively). No statistically significant difference was found in terms of the levels of Substance P, CGRP, and IL-10 among groups (p > .05), except IL-6. CONCLUSIONS: PTUR, RB, and DR + XPFR files have comparable results in the expression of inflammatory mediators. CLINICAL RELEVANCE: Retreatment files powered with rotary or reciprocating motion produced similar neuropeptide and cytokine levels in patients.

Influence of temperature on the torsional properties of two thermally treated NiTi rotary instruments.

This study aimed to evaluate the influence of temperature on torsional strength and angular deflection of two experimental NiTi rotary instruments manufactured from Blue and Gold thermal treatments and with identical cross-sections. A total of 40 experimental NiTi instruments 25.06 and with a triangular cross-section and manufactured from Blue and Gold thermal treatments were used (n=20). The torsional test was performed in the 3 mm from the tip of the instrument according to ISO 3630-1. The torsional test evaluated the torsional strength and angular deflection to failure at room temperature (21°C ± 1° C) and body temperature (36°C ±1°C). The fractured surface of each fragment was observed by using scanning electron microscopy (SEM). Data were analyzed using an unpaired t test for inter and intra-group comparison and the level of significance was set at 5%. The results showed that the body temperature did not affect the torsional strength and angular deflection of the instruments when compared with room temperature (P>0.05). However, at body temperature, the Blue NiTi instruments presented significantly lower angular deflection in comparison with Gold NiTi instruments (P<0.05). There was no significant difference regarding the torsional strength of the instruments at body temperature (P>0.05). The temperature did not affect the torsional strength of the instruments manufactured from Blue and Gold technology. However, the Blue NiTi instruments presented significantly lower angular deflection than Gold instruments at 36°C temperature.

Análisis microbiológico a corto y largo plazo del material usado para esterilizar instrumental odontológico / Short and long-term microbiological analysis of the material for sterilize dental instruments

Introducción: el material para empaquetar el instrumental odontológico, como pueden ser bolsas de tela, papel o plástico, es usado por profesionales de la salud; sin embargo, es necesario esclarecer la efectividad de cada uno y determinar el tiempo que permanece estéril luego del procedimiento. Objetivo: identificar la eficacia de tela, plástico y papel como materiales para esterilizar instrumental a corto y largo plazo. Material y métodos: se realizaron cultivos sólidos y líquidos de instrumental esterilizado en tres materiales y con diferentes tiempos de postesterilización. Se incubaron a 36 oC por 72 horas en condiciones aerobias y anaerobias. Los resultados se analizaron usando una prueba de Kruskal-Wallis, seguida de una prueba de Dunn. Resultados: los resultados mostraron que inmediatamente después del proceso de esterilización, los tres materiales son efectivos (Kruskal-Wallis test, p = 0.2752), 24 horas (p = 0.2492), siete (p = 0.0509) y 14 días (p = 0.0006). Veinticuatro horas posterior a la esterilización la tela no es efectiva, el plástico disminuye su efectividad y el papel sigue siendo efectivo. Conclusión: en nuestros resultados, el papel es la mejor opción para esterilizar instrumental (AU)

Introduction: material such as cloth, paper or plastic bags to wrap dental instruments is used by health professionals, however, it is necessary to clarify the effectiveness of each one and determine if it remains sterile after the procedure. Objective: to determine the effectiveness of cloth, plastic and paper as materials to sterilize dental instruments in the short and long term. Material and methods: we carry out solid and liquid cultures of sterilized instruments in three materials, at different post-sterilization times, incubated at 36 oC for 72 hours under aerobic and anaerobic conditions, and the results were analyzed using a Kruskal-Wallis test, followed by from a Dunn's test. Results: our results showed that immediately after the sterilization process the three materials are effective (Kruskal-Wallis; p = 0.2752), 24 hours (p = 0.2492), 7 (p = 0.0509) and 14 (p = 0.0006) days. Twenty-four hours after the cloth is not effective, plastic decreases its effectiveness and paper remain effective. Conclusion: in our results, paper is the best option to sterilize dental instruments (AU)

Design, metallurgy, mechanical properties, and shaping ability of 3 heat-treated reciprocating systems: a multimethod investigation.

OBJECTIVE: This study aimed to compare 3 reciprocating systems regarding design, metallurgy, mechanical properties, and shaping ability. MATERIALS AND METHODS: New Reciproc Blue R25, WaveOne Gold Primary, and REX 25 instruments (n=41 per group) were analyzed regarding design, metallurgy, and mechanical performance, while shaping ability (untouched canal walls, volume of removed dentin, and hard tissue debris) was tested in 36 anatomically matched root canals of mandibular molars. Results were compared using one-way ANOVA post hoc Tukey and Kruskal-Wallis tests with a significant level set at 5%. RESULTS: All instruments showed symmetrical cross sections with asymmetrical blades, no radial lands, no major defects, and an almost equiatomic nickel and titanium ratio. The highest R-phase start temperatures were observed with WaveOne Gold (46.1°C) and REX (44.8°C), while Reciproc Blue had the lowest R-phase start (34.5°C) and finish (20°C) temperatures. WaveOne Gold had the lowest time to fracture (169 s) and the highest maximum load (301.6 gf) (P <0.05). The maximum torque of Reciproc Blue (2.2 N.cm) and WaveOne Gold (2.1 N.cm) were similar (P >0.05), but lower than REX (2.6 N.cm) (P <0.05). No statistical differences were observed among instruments in the angle of rotation (P >0.05) and in the shaping ability in both mesial and distal canals (P >0.05). CONCLUSION: Although the overall design, temperature transition phases and mechanical behavior parameters were different among tested instruments, they were similar in terms of shaping ability. CLINICAL RELEVANCE: All tested heat-treated NiTi reciprocating systems showed similar shaping ability, without clinically significant errors.

Perception of Dental House Officers regarding Endodontic File Separation during Endodontic Treatment.

Background: Despite of having improved endodontic file designs as well as the reinforced metal alloy file structure, intracanal endodontic file separation (EFS) is still a very problematic and worrisome dental incident, which usually occurs without any visible signs of permanent deformation. Further, there have been conflicting reports regarding the clinical significance of leaving separated files within root canals. Aims: The aim of this study was to look into the current perceptions and awareness about file separation during endodontic treatment among the dental house officers (DHOs). Materials and Methods: A novel validated questionnaire comprising of 15 close-ended questions was distributed anonymously via Google Forms through email to 1100 DHOs across Pakistan. The questionnaire consisted of two parts: the first component (Section I) collected demographic data and the second component (Section II) investigated the causes of EFS during root canal treatment. Following the completion of socioeconomic information, including age and gender, the DHOs were asked to answer a few questions about the various reasons for endodontic instrument fracture. Results: A total of 800 responses were recorded, with an effective rate of 72.8%. The majority of the DHOs (p value < 0.001) perceived that endodontic instrument fracture occurred in the posterior (61.5%) and apical third of the canal (50.5%) and in older permanent dentition (67.3%), possibly due to patient anxiety (62%). Better choice of instrument (61.15%), operators' experience (95.3%), knowledge (87.5%), and proper root canal cleaning (91.1%) are believed to be the vital steps in reducing endodontic file separation/fracture. Furthermore, majority of them (p value < 0.001) perceived that stainless steel was a superior alloy for filing instruments. Manual files tend to be more prone to fractures due to repeated use than rotary files. Conclusion: This study demonstrated that young DHOs had adequate knowledge and awareness regarding the potential predisposing factors and handling techniques for EFS. This study thereby provides an evaluating tool to access the insights of the current perceptions and awareness of DHOs concerning EFS.