Detecting cardiac states with wearable photoplethysmograms and implications for out-of-hospital cardiac arrest detection.

Out-of-hospital cardiac arrest (OHCA) is a global health problem affecting approximately 4.4 million individuals yearly. OHCA has a poor survival rate, specifically when unwitnessed (accounting for up to 75% of cases). Rapid recognition can significantly improve OHCA survival, and consumer wearables with continuous cardiopulmonary monitoring capabilities hold potential to "witness" cardiac arrest and activate emergency services. In this study, we used an arterial occlusion model to simulate cardiac arrest and investigated the ability of infrared photoplethysmogram (PPG) sensors, often utilized in consumer wearable devices, to differentiate normal cardiac pulsation, pulseless cardiac (i.e., resembling a cardiac arrest), and non-physiologic (i.e., off-body) states. Across the classification models trained and evaluated on three anatomical locations, higher classification performances were observed on the finger (macro average F1-score of 0.964 on the fingertip and 0.954 on the finger base) compared to the wrist (macro average F1-score of 0.837). The wrist-based classification model, which was trained and evaluated using all PPG measurements, including both high- and low-quality recordings, achieved a macro average precision and recall of 0.922 and 0.800, respectively. This wrist-based model, which represents the most common form factor in consumer wearables, could only capture about 43.8% of pulseless events. However, models trained and tested exclusively on high-quality recordings achieved higher classification outcomes (macro average F1-score of 0.975 on the fingertip, 0.973 on the finger base, and 0.934 on the wrist). The fingertip model had the highest performance to differentiate arterial occlusion pulselessness from normal cardiac pulsation and off-body measurements with macro average precision and recall of 0.978 and 0.972, respectively. This model was able to identify 93.7% of pulseless states (i.e., resembling a cardiac arrest event), with a 0.4% false positive rate. All classification models relied on a combination of time-, power spectral density (PSD)-, and frequency-domain features to differentiate normal cardiac pulsation, pulseless cardiac, and off-body PPG recordings. However, our best model represented an idealized detection condition, relying on ensuring high-quality PPG data for training and evaluation of machine learning algorithms. While 90.7% of our PPG recordings from the fingertip were considered of high quality, only 53.2% of the measurements from the wrist passed the quality criteria. Our findings have implications for adapting consumer wearables to provide OHCA detection, involving advancements in hardware and software to ensure high-quality measurements in real-world settings, as well as development of wearables with form factors that enable high-quality PPG data acquisition more consistently. Given these improvements, we demonstrate that OHCA detection can feasibly be made available to anyone using PPG-based consumer wearables.

Unobtrusive measurement of cognitive load and physiological signals in uncontrolled environments.

While individuals fail to assess their mental health subjectively in their day-to-day activities, the recent development of consumer-grade wearable devices has enormous potential to monitor daily workload objectively by acquiring physiological signals. Therefore, this work collected consumer-grade physiological signals from twenty-four participants, following a four-hour cognitive load elicitation paradigm with self-chosen tasks in uncontrolled environments and a four-hour mental workload elicitation paradigm in a controlled environment. The recorded dataset of approximately 315 hours consists of electroencephalography, acceleration, electrodermal activity, and photoplethysmogram data balanced across low and high load levels. Participants performed office-like tasks in the controlled environment (mental arithmetic, Stroop, N-Back, and Sudoku) with two defined difficulty levels and in the uncontrolled environments (mainly researching, programming, and writing emails). Each task label was provided by participants using two 5-point Likert scales of mental workload and stress and the pairwise NASA-TLX questionnaire. This data is suitable for developing real-time mental health assessment methods, conducting research on signal processing techniques for challenging environments, and developing personal cognitive load assistants.

Assessment of the relational strength between triggers detected in physiological signals and the occurrence of atrial fibrillation episodes.

Objective.Despite the growing interest in understanding the role of triggers of paroxysmal atrial fibrillation (AF), solutions beyond questionnaires to identify a broader range of triggers remain lacking. This study aims to investigate the relation between triggers detected in wearable-based physiological signals and the occurrence of AF episodes.Approach.Week-long physiological signals were collected during everyday activities from 35 patients with paroxysmal AF, employing an ECG patch attached to the chest and a photoplethysmogram (PPG)-based wrist-worn device. The signals acquired by the patch were used for detecting potential triggers due to physical exertion, psychophysiological stress, lying on the left side, and sleep disturbances. To assess the relation between detected triggers and the occurrence of AF episodes, a measure of relational strength is employed accounting for pre- and post-trigger AF burden. The usefulness of ECG- and PPG-based AF detectors in determining AF burden and assessing the relational strength is also analyzed.Main results.Physical exertion emerged as the trigger associated with the largest increase in relational strength for the largest number of patients (p < 0.01). On the other hand, no significant difference was observed for psychophysiological stress and sleep disorders. The relational strength of the detected AF exhibits a moderate correlation with the relational strength of annotated AF, withr = 0.66 for ECG-based AF detection andr = 0.62 for PPG-based AF detection.Conclusions.The findings indicate a patient-specific increase in relational strength for all four types of trigger.Significance.The proposed approach has the potential to facilitate the implementation of longitudinal studies and can serve as a less biased alternative to questionnaire-based AF trigger detection.

Testing preload responsiveness by the tidal volume challenge assessed by the photoplethysmographic perfusion index.

BACKGROUND: To detect preload responsiveness in patients ventilated with a tidal volume (Vt) at 6 mL/kg of predicted body weight (PBW), the Vt-challenge consists in increasing Vt from 6 to 8 mL/kg PBW and measuring the increase in pulse pressure variation (PPV). However, this requires an arterial catheter. The perfusion index (PI), which reflects the amplitude of the photoplethysmographic signal, may reflect stroke volume and its respiratory variation (pleth variability index, PVI) may estimate PPV. We assessed whether Vt-challenge-induced changes in PI or PVI could be as reliable as changes in PPV for detecting preload responsiveness defined by a PLR-induced increase in cardiac index (CI) ≥ 10%. METHODS: In critically ill patients ventilated with Vt = 6 mL/kg PBW and no spontaneous breathing, haemodynamic (PICCO2 system) and photoplethysmographic (Masimo-SET technique, sensor placed on the finger or the forehead) data were recorded during a Vt-challenge and a PLR test. RESULTS: Among 63 screened patients, 21 (33%) were excluded because of an unstable PI signal and/or atrial fibrillation and 42 were included. During the Vt-challenge in the 16 preload responders, CI decreased by 4.8 ± 2.8% (percent change), PPV increased by 4.4 ± 1.9% (absolute change), PIfinger decreased by 14.5 ± 10.7% (percent change), PVIfinger increased by 1.9 ± 2.6% (absolute change), PIforehead decreased by 18.7 ± 10.9 (percent change) and PVIforehead increased by 1.0 ± 2.5 (absolute change). All these changes were larger than in preload non-responders. The area under the ROC curve (AUROC) for detecting preload responsiveness was 0.97 ± 0.02 for the Vt-challenge-induced changes in CI (percent change), 0.95 ± 0.04 for the Vt-challenge-induced changes in PPV (absolute change), 0.98 ± 0.02 for Vt-challenge-induced changes in PIforehead (percent change) and 0.85 ± 0.05 for Vt-challenge-induced changes in PIfinger (percent change) (p = 0.04 vs. PIforehead). The AUROC for the Vt-challenge-induced changes in PVIforehead and PVIfinger was significantly larger than 0.50, but smaller than the AUROC for the Vt-challenge-induced changes in PPV. CONCLUSIONS: In patients under mechanical ventilation with no spontaneous breathing and/or atrial fibrillation, changes in PI detected during Vt-challenge reliably detected preload responsiveness. The reliability was better when PI was measured on the forehead than on the fingertip. Changes in PVI during the Vt-challenge also detected preload responsiveness, but with lower accuracy.

[Research on dynamic blood oxygen saturation measurement based on motion noise reconstruction combined with convex combination least mean square adaptive filter].

The performance of a pulse oximeter based on photoelectric detection is greatly affected by motion noise (MA) in the photoplethysmographic (PPG) signal. This paper presents an algorithm for detecting motion oxygen saturation, which reconstructs a motion noise reference signal using ensemble of complete adaptive noise and empirical mode decomposition combined with multi-scale permutation entropy, and eliminates MA in the PPG signal using a convex combination least mean square adaptive filters to calculate dynamic oxygen saturation. The test results show that, under simulated walking and jogging conditions, the mean absolute error (MAE) of oxygen saturation estimated by the proposed algorithm and the reference oxygen saturation are 0.05 and 0.07, respectively, with means absolute percentage error (MAPE) of 0.05% and 0.07%, respectively. The overall Pearson correlation coefficient reaches 0.971 2. The proposed scheme effectively reduces motion artifacts in the corrupted PPG signal and is expected to be applied in portable photoelectric pulse oximeters to improve the accuracy of dynamic oxygen saturation measurement.

Variability of morphology in photoplethysmographic waveform quantified with unsupervised wave-shape manifold learning for clinical assessment.

Objective.We investigated fluctuations of the photoplethysmography (PPG) waveform in patients undergoing surgery. There is an association between the morphologic variation extracted from arterial blood pressure (ABP) signals and short-term surgical outcomes. The underlying physiology could be the numerous regulatory mechanisms on the cardiovascular system. We hypothesized that similar information might exist in PPG waveform. However, due to the principles of light absorption, the noninvasive PPG signals are more susceptible to artifacts and necessitate meticulous signal processing.Approach.Employing the unsupervised manifold learning algorithm, dynamic diffusion map, we quantified multivariate waveform morphological variations from the PPG continuous waveform signal. Additionally, we developed several data analysis techniques to mitigate PPG signal artifacts to enhance performance and subsequently validated them using real-life clinical database.Main results.Our findings show similar associations between PPG waveform during surgery and short-term surgical outcomes, consistent with the observations from ABP waveform analysis.Significance.The variation of morphology information in the PPG waveform signal in major surgery provides clinical meanings, which may offer new opportunity of PPG waveform in a wider range of biomedical applications, due to its non-invasive nature.

A novel computational signal processing framework towards multimodal vital signs extraction using neck-worn wearable devices.

Pulse rate (PR) and respiratory rate (RR) are two of the most important vital signs. Monitoring them would benefit from easy-to-use technologies. Hence, wearable devices would, in principle, be ideal candidates for such systems. The neck, although highly susceptible to artifacts, presents an attractive location for a diverse pool of physiological biomarkers monitoring purposes such as airflow sensing in a non-obstructive manner. This paper presents a methodology for PR and RR estimation using photoplethysmography (PPG) and accelerometry (Acc) sensors placed on the neck. Neck PPG and Acc signals were recorded from 22 healthy participants for RR estimation, where the resting subjects performed guided breathing following a visual metronome. Neck PPG signals were obtained from 16 healthy participants who breathed through an altitude generator machine in order to acquire a wider range of PR readings while at rest. The proposed methodology was able to provide rate estimates via a combination of recursive FFT-based dominance scoring coupled with an exponentially weighted moving average (EWMA)-driven aggregation scheme. The recursion aimed at bypassing sudden intra-window amplitude deviations caused by momentary artifacts, while the EWMA-based aggregation was utilized for handling inter-window artifact-induced deviations. To further improve estimation stability and confidence, estimates were calculated in the form of rate bands taking into account the relevant clinically acceptable error margins, and results when considering rate values and rate bands are presented and discussed. The framework was able to achieve an overall pulse rate value accuracy of 93.67 ± 7.64 % within the clinically acceptable ± 5 BPM with reference to the gold-standard reference devices while providing an overall respiratory rate value accuracy within the clinically appropriate ± 3 BrPM of 94.94 ± 3.56 % with reference to the guiding visual metronome, and 88.4 ± 7.63 % with respect to the gold-standard reference device. The proposed methodology achieves acceptable PR and RR estimation capabilities, even when signals are acquired from an unusual location such as the neck. This work introduces novel ideas that can lead to the development of medical device outputs for PR and RR monitoring, especially capitalizing on the advantages of the neck as a multi-modal physiological monitoring location.

Diagnostic Potential of Combined Photoplethysmography and Ankle-Brachial Index in Peripheral Arterial Disease: A Duplex Ultrasonography-Based Comparative Study.

BACKGROUND: Although ankle-brachial index (ABI) and photoplethysmography (PPG) have also shown adequate sensitivity in detecting peripheral arterial disease, their diagnostic performance is less reliable in asymptomatic cases or those with high atherosclerotic cardiovascular risks. METHODS AND RESULTS: We evaluated 130 participants using ABI, PPG, and duplex ultrasonography, diagnosing 65 with peripheral arterial disease. From the PPG, we derived 2 parameters: PPG amplitude ratio of the lower-to-upper extremities (PPGratio) and the PPG amplitude of the lower extremity (PPGamp). Sensitivity, specificity, accuracy, and the area under receiver operating characteristic (ROC) curve were calculated for PPG parameters and ABI, and their combination of both methods. Univariate and multivariate logistic regression assessed the prognostic potential of these parameters. ROC analysis revealed optimal cutoff values in diagnosing peripheral arterial disease were 0.417 for PPGratio and "58" for PPGamp. Both PPGratio and PPGamp demonstrated significantly higher sensitivities, 78.4% and 75.7%, respectively, compared with 55.9% for ABI <0.9 (P<0.05). The areas under the ROC curves of combination models, including model 1 (ABI <0.9 and PPGratio), model 2 (ABI <0.9 and PPGamp), and model 3 (ABI <0.9, PPGratio, and PPGamp), exhibited improved performance with areas under the ROC curves of 0.922, 0.922, and 0.931 (all P<0.01) compared with ABI alone (area under the ROC curve, 0.822). Additionally, the PPG parameters, both alone and combined with ABI, were associated with major adverse cardiac events and all-cause mortality after adjusting for other relevant factors. CONCLUSIONS: On the basis of duplex ultrasonography, combining ABI and PPG markedly improves peripheral arterial disease diagnosis in high-risk individuals compared with either method alone and provides crucial insights into major adverse cardiac events and all-cause mortality risks.

Advanced Necklace for Real-Time PPG Monitoring in Drivers.

Monitoring heart rate (HR) through photoplethysmography (PPG) signals is a challenging task due to the complexities involved, even during routine daily activities. These signals can indeed be heavily contaminated by significant motion artifacts resulting from the subjects' movements, which can lead to inaccurate heart rate estimations. In this paper, our objective is to present an innovative necklace sensor that employs low-computational-cost algorithms for heart rate estimation in individuals performing non-abrupt movements, specifically drivers. Our solution facilitates the acquisition of signals with limited motion artifacts and provides acceptable heart rate estimations at a low computational cost. More specifically, we propose a wearable sensor necklace for assessing a driver's well-being by providing information about the driver's physiological condition and potential stress indicators through HR data. This innovative necklace enables real-time HR monitoring within a sleek and ergonomic design, facilitating seamless and continuous data gathering while driving. Prioritizing user comfort, the necklace's design ensures ease of wear, allowing for extended use without disrupting driving activities. The collected physiological data can be transmitted wirelessly to a mobile application for instant analysis and visualization. To evaluate the sensor's performance, two algorithms for estimating the HR from PPG signals are implemented in a microcontroller: a modified version of the mountaineer's algorithm and a sliding discrete Fourier transform. The goal of these algorithms is to detect meaningful peaks corresponding to each heartbeat by using signal processing techniques to remove noise and motion artifacts. The developed design is validated through experiments conducted in a simulated driving environment in our lab, during which drivers wore the sensor necklace. These experiments demonstrate the reliability of the wearable sensor necklace in capturing dynamic changes in HR levels associated with driving-induced stress. The algorithms integrated into the sensor are optimized for low computational cost and effectively remove motion artifacts that occur when users move their heads.

Raw Photoplethysmography as an Enhancement for Research-Grade Wearable Activity Monitors.

Wearable monitors continue to play a critical role in scientific assessments of physical activity. Recently, research-grade monitors have begun providing raw data from photoplethysmography (PPG) alongside standard raw data from inertial sensors (accelerometers and gyroscopes). Raw PPG enables granular and transparent estimation of cardiovascular parameters such as heart rate, thus presenting a valuable alternative to standard PPG methodologies (most of which rely on consumer-grade monitors that provide only coarse output from proprietary algorithms). The implications for physical activity assessment are tremendous, since it is now feasible to monitor granular and concurrent trends in both movement and cardiovascular physiology using a single noninvasive device. However, new users must also be aware of challenges and limitations that accompany the use of raw PPG data. This viewpoint paper therefore orients new users to the opportunities and challenges of raw PPG data by presenting its mechanics, pitfalls, and availability, as well as its parallels and synergies with inertial sensors. This includes discussion of specific applications to the prediction of energy expenditure, activity type, and 24-hour movement behaviors, with an emphasis on areas in which raw PPG data may help resolve known issues with inertial sensing (eg, measurement during cycling activities). We also discuss how the impact of raw PPG data can be maximized through the use of open-source tools when developing and disseminating new methods, similar to current standards for raw accelerometer and gyroscope data. Collectively, our comments show the strong potential of raw PPG data to enhance the use of research-grade wearable activity monitors in science over the coming years.

Inferring ECG Waveforms from PPG Signals with a Modified U-Net Neural Network.

There are two widely used methods to measure the cardiac cycle and obtain heart rate measurements: the electrocardiogram (ECG) and the photoplethysmogram (PPG). The sensors used in these methods have gained great popularity in wearable devices, which have extended cardiac monitoring beyond the hospital environment. However, the continuous monitoring of ECG signals via mobile devices is challenging, as it requires users to keep their fingers pressed on the device during data collection, making it unfeasible in the long term. On the other hand, the PPG does not contain this limitation. However, the medical knowledge to diagnose these anomalies from this sign is limited by the need for familiarity, since the ECG is studied and used in the literature as the gold standard. To minimize this problem, this work proposes a method, PPG2ECG, that uses the correlation between the domains of PPG and ECG signals to infer from the PPG signal the waveform of the ECG signal. PPG2ECG consists of mapping between domains by applying a set of convolution filters, learning to transform a PPG input signal into an ECG output signal using a U-net inception neural network architecture. We assessed our proposed method using two evaluation strategies based on personalized and generalized models and achieved mean error values of 0.015 and 0.026, respectively. Our method overcomes the limitations of previous approaches by providing an accurate and feasible method for continuous monitoring of ECG signals through PPG signals. The short distances between the infer-red ECG and the original ECG demonstrate the feasibility and potential of our method to assist in the early identification of heart diseases.

An efficient model for extracting respiratory and blood oxygen saturation data from photoplethysmogram signals by removing motion artifacts using heuristic-aided ensemble learning model.

Patients with surgical, pulmonary, and cardiac problems, continual monitoring of Oxygen Saturation of a Person (SpO2) and Respiratory Rate (RR) is essential. Similarly, the persons with cardiopulmonary health issues, RR estimation is crucial. The performance of the ventilator assistance and lung medicines are evaluated using SpO2 and RR. For the persons, those who are living alone with respiratory illnesses need a compulsory estimation of RR. In case of serious illness, the RR might face abrupt changes. The immobility of the disturbance and RR makes the RR evaluation from the PhotoPlethysmoGraphic (PPG) signals is a difficult challenge. So, an efficient RR and SpO2 estimation framework from the PPG signal using the deep learning method is developed in this paper. At first, the PPG signal is collected from standard data sources. The collected PPG signals undergo signal pre-processing. The pre-processing procedures include Motion Artifacts (MA) removal and filtering techniques. The pre-processed signals are split into distinct windows. From the split windows of the signals, the spectral features, RR, and Respiratory Peak Variance (RPV) features are extracted. The retrieved features are selected optimally with the help of Advanced Golden Tortoise Beetle Optimizer (AGTBO). The weights are chosen optimally with the same AGTBO. The optimally selected features are fused with the optimal features to get the weighted optimal features. These weighted optimal features are fed into the Ensemble Learning-based RR and SpO2 Estimation Network (ELRR-SpO2EN). The ensemble learning model is developed by combining Multilayer Perceptron (MLP), AdaBoost, and Attention-based Long Short Term Memory (A-LSTM). The performance of the developed RR and SpO2 estimation model is compared with other existing techniques. The experimental analysis results revealed that the proposed AGTBO-ELRR-SpO2EN model attained 96 % accuracy for the second dataset, which is higher than the conventional models such as MLP (90 %), Adaboost (92 %), A-LSTM (92 %), and MLP-ADA-ALSTM (94 %). Thus, it has been confirmed that the designed RR and SpO2 estimation framework from PPG signals is more efficient than the other conventional models.

Understanding the physiological transmission mechanisms of photoplethysmography signals: a comprehensive review.

Objective. The widespread adoption of Photoplethysmography (PPG) as a non-invasive method for detecting blood volume variations and deriving vital physiological parameters reflecting health status has surged, primarily due to its accessibility, cost-effectiveness, and non-intrusive nature. This has led to extensive research around this technique in both daily life and clinical applications. Interestingly, despite the existence of contradictory explanations of the underlying mechanism of PPG signals across various applications, a systematic investigation into this crucial matter has not been conducted thus far. This gap in understanding hinders the full exploitation of PPG technology and undermines its accuracy and reliability in numerous applications.Approach. Building upon a comprehensive review of the fundamental principles and technological advancements in PPG, this paper initially attributes the origin of PPG signals to a combination of physical and physiological transmission processes. Furthermore, three distinct models outlining the concerned physiological transmission processes are synthesized, with each model undergoing critical examination based on theoretical underpinnings, empirical evidence, and constraints.Significance. The ultimate objective is to form a fundamental framework for a better understanding of physiological transmission processes in PPG signal generation and to facilitate the development of more reliable technologies for detecting physiological signals.

Multimodal Signal Fusion for Heartbeat Monitoring on eScooters.

Integrating continuous monitoring into everyday objects enables the early detection of diseases. This paper presents a novel approach to heartbeat monitoring on eScooters using multi-modal signal fusion. We explore heartbeat monitoring using electrocardiography (ECG) and photoplethysmography (PPG) and evaluate four signal fusion approaches based on convolutional neural network (CNN) and long short-term memory (LSTM) architectures. We perform an evaluation study using skin-attached ECG electrodes for ground truth generation. The CNN+LSTM late fusion accurately measures the heartbeat for 76.17% of the driving time.

Robust In-Vehicle Signal Quality Assessment Using Multimodal Signal Fusion.

Continuous monitoring of physiological signals such as electrocardiogram (ECG) in driving environments has the potential to reduce the need for frequent health check-ups by providing real-time information on cardiovascular health. However, capturing ECG from sensors mounted on steering wheels creates difficulties due to motion artifacts, noise, and dropouts. To address this, we propose a novel method for reliable and accurate detection of heartbeats using sensor fusion with a bidirectional long short-term memory (BiLSTM) model. Our dataset contains reference ECG, steering wheel ECG, photoplethysmogram (PPG), and imaging PPG (iPPG) signals, which are more feasible to capture in driving scenarios. We combine these signals for R-wave detection. We conduct experiments with individual signals and signal fusion techniques to evaluate the performance of detected heartbeat positions. The BiLSTMs model achieves a performance of 62.69% in the driving scenario city. The model can be integrated into the system to detect heartbeat positions for further analysis.

Intelligent Detection Method of Atrial Fibrillation by CEPNCC-BiLSTM Based on Long-Term Photoplethysmography Data.

Atrial fibrillation (AF) is the most prevalent arrhythmia characterized by intermittent and asymptomatic episodes. However, traditional detection methods often fail to capture the sporadic and intricate nature of AF, resulting in an increased risk of false-positive diagnoses. To address these challenges, this study proposes an intelligent AF detection and diagnosis method that integrates Complementary Ensemble Empirical Mode Decomposition, Power-Normalized Cepstral Coefficients, Bi-directional Long Short-term Memory (CEPNCC-BiLSTM), and photoelectric volumetric pulse wave technology to enhance accuracy in detecting AF. Compared to other approaches, the proposed method demonstrates faster preprocessing efficiency and higher sensitivity in detecting AF while effectively filtering out false alarms from photoplethysmography (PPG) recordings of non-AF patients. Considering the limitations of conventional AF detection evaluation systems that lack a comprehensive assessment of efficiency and accuracy, this study proposes the ET-score evaluation system based on F-measurement, which incorporates both computational speed and accuracy to provide a holistic assessment of overall performance. Evaluated with the ET-score, the CEPNCC-BiLSTM method outperforms EEMD-based improved Power-Normalized Cepstral Coefficients and Bi-directional Long Short-term Memory (EPNCC-BiLSTM), Support Vector Machine (SVM), EPNCC-SVM, and CEPNCC-SVM methods. Notably, this approach achieves an outstanding accuracy rate of up to 99.2% while processing PPG recordings within 5 s, highlighting its potential for long-term AF monitoring.

Data-knowledge co-driven feature based prediction model via photoplethysmography for evaluating blood pressure.

BACKGROUND: Knowledge feature (KF) with clear physiological significance of photoplethysmography are widely used in predicting blood pressure. However, KF primarily focus on local information of photoplethysmography, which may struggle to capture the overall characteristics. METHODS: Firstly, functional data analysis (FDA) was introduced to extract two types of data feature (DF). Furthermore, data-knowledge co-driven feature (DKCF) was proposed by combining FDA and constraints of KF. Finally, random forest, ada boost, gradient boosting, support vector machine and deep neural network were adopted, to compare the abilities of KF, DFs and DKCF in predicting blood pressure with two datasets (A published dataset and a self-collected dataset). RESULTS: Under the premise of extracting only 9 features, the average mean absolute errors (MAE) of systolic blood pressure (SBP) and diastolic blood pressure (DBP) obtained by DKCF are both the smallest in dataset 1. In dataset 2, DKCF acquires the smallest MAE in predicting SBP and obtains the second smallest MAE in predicting DBP. CONCLUSIONS: The results demonstrate that low-dimensional DKCF of photoplethysmography is closely correlated with blood pressure, which may serve as an important indicator for health assessment.

Compressed Deep Learning Models for Wearable Atrial Fibrillation Detection through Attention.

Deep learning (DL) models have shown promise for the accurate detection of atrial fibrillation (AF) from electrocardiogram/photoplethysmography (ECG/PPG) data, yet deploying these on resource-constrained wearable devices remains challenging. This study proposes integrating a customized channel attention mechanism to compress DL neural networks for AF detection, allowing the model to focus only on the most salient time-series features. The results demonstrate that applying compression through channel attention significantly reduces the total number of model parameters and file size while minimizing loss in detection accuracy. Notably, after compression, performance increases for certain model variants in key AF databases (ADB and C2017DB). Moreover, analyzing the learned channel attention distributions after training enhances the explainability of the AF detection models by highlighting the salient temporal ECG/PPG features most important for its diagnosis. Overall, this research establishes that integrating attention mechanisms is an effective strategy for compressing large DL models, making them deployable on low-power wearable devices. We show that this approach yields compressed, accurate, and explainable AF detectors ideal for wearables. Incorporating channel attention enables simpler yet more accurate algorithms that have the potential to provide clinicians with valuable insights into the salient temporal biomarkers of AF. Our findings highlight that the use of attention is an important direction for the future development of efficient, high-performing, and interpretable AF screening tools for wearable technology.

Fluid-Solid Interaction Analysis for Developing In-Situ Strain and Flow Sensors for Prosthetic Valve Monitoring.

Transcatheter aortic valve implantation (TAVI) was initially developed for adult patients, but there is a growing interest to expand this procedure to younger individuals with longer life expectancies. However, the gradual degradation of biological valve leaflets in transcatheter heart valves (THV) presents significant challenges for this extension. This study aimed to establish a multiphysics computational framework to analyze structural and flow measurements of TAVI and evaluate the integration of optical fiber and photoplethysmography (PPG) sensors for monitoring valve function. A two-way fluid-solid interaction (FSI) analysis was performed on an idealized aortic vessel before and after the virtual deployment of the SAPIEN 3 Ultra (S3) THV. Subsequently, an analytical analysis was conducted to estimate the PPG signal using computational flow predictions and to analyze the effect of different pressure gradients and distances between PPG sensors. Circumferential strain estimates from the embedded optical fiber in the FSI model were highest in the sinus of Valsalva; however, the optimal fiber positioning was found to be distal to the sino-tubular junction to minimize bending effects. The findings also demonstrated that positioning PPG sensors both upstream and downstream of the bioprosthesis can be used to effectively assess the pressure gradient across the valve. We concluded that computational modeling allows sensor design to quantify vessel wall strain and pressure gradients across valve leaflets, with the ultimate goal of developing low-cost monitoring systems for detecting valve deterioration.

Examining the challenges of blood pressure estimation via photoplethysmogram.

The use of observed wearable sensor data (e.g., photoplethysmograms [PPG]) to infer health measures (e.g., glucose level or blood pressure) is a very active area of research. Such technology can have a significant impact on health screening, chronic disease management and remote monitoring. A common approach is to collect sensor data and corresponding labels from a clinical grade device (e.g., blood pressure cuff) and train deep learning models to map one to the other. Although well intentioned, this approach often ignores a principled analysis of whether the input sensor data have enough information to predict the desired metric. We analyze the task of predicting blood pressure from PPG pulse wave analysis. Our review of the prior work reveals that many papers fall prey to data leakage and unrealistic constraints on the task and preprocessing steps. We propose a set of tools to help determine if the input signal in question (e.g., PPG) is indeed a good predictor of the desired label (e.g., blood pressure). Using our proposed tools, we found that blood pressure prediction using PPG has a high multi-valued mapping factor of 33.2% and low mutual information of 9.8%. In comparison, heart rate prediction using PPG, a well-established task, has a very low multi-valued mapping factor of 0.75% and high mutual information of 87.7%. We argue that these results provide a more realistic representation of the current progress toward the goal of wearable blood pressure measurement via PPG pulse wave analysis. For code, see our project page: https://github.com/lirus7/PPG-BP-Analysis.