Potential use of sludge from El Ferrol Bay (Chimbote, Peru) for the production of lipids in the culture of Scenedesmus acutus (Meyen, 1829).

Despite the extensive development of microalgae biotechnology, it still requires new methodologies to lower production costs, especially in the field of biofuel production. Therefore, innovative methods that facilitate operations and enable cost-effective production are important in driving this industry. In this study, we propose a new low-cost and easy-to-use procedure, addressed to the generation of a culture medium for Scenedesmus acutus. The medium was obtained by thermal reduction of a sludge sample from El Ferrol Bay (Chimbote, Peru), whereby we obtained an aqueous medium. Our results indicated that the aqueous medium incorporates all necessary nutrients for microalgae production; allowing a maximum biomass of 0.75 ± 0.07 g/L with 60% of the medium; while high lipids production (59.42 ± 6.16%) was achieved with 20%. Besides, we quantified, in the experimental medium and at the end of the cultures, the levels of inorganic nutrients such as ammonium, nitrites, nitrates, and phosphates; in addition to COD and TOC, which were significantly reduced ( p < 0.05) after 7 days of culture, mainly in the treatment with 20%. These results suggest tremendous potential for sludge reuse, which also entails a cost reduction in microalgae biomass production, with additional positive impacts on large-scale application over highly polluted environments.

Elucidating the impacts of cobalt (II) ions on extracellular electron transfer and pollutant degradation by anodic biofilms in bioelectrochemical systems during industrial wastewater treatment.

Electrogenic biofilms in bioelectrochemical systems (BES) are critical in wastewater treatment. Industrial effluents often contain cobalt (Co2+); however, its impact on biofilms is unknown. This study investigated how increasing Co2+ concentrations (0-30 mg/L) affect BES biofilm community dynamics, extracellular polymeric substances, microbial metabolism, electron transfer gene expression, and electrochemical performance. The research revealed that as Co2+ concentrations increased, power generation progressively declined, from 345.43 ± 4.07 mW/m2 at 0 mg/L to 160.51 ± 0.86 mW/m2 at 30 mg/L Co2+. However, 5 mg/L Co2+ had less effect. The Co2+ removal efficiency in the reactors fed with 5 and 10 mg/L concentrations exceeded 99% and 94%, respectively. However, at 20 and 30 mg/L, the removal efficiency decreased substantially, likely because of reduced biofilm viability. FTIR indicated the participation of biofilm functional groups in Co2+ uptake. XPS revealed Co2+ presence in biofilms as CoO and Co(OH)2, indicating precipitation also aided removal. Cyclic voltammetry and electrochemical impedance spectroscopy tests revealed that 5 mg/L Co2+ had little impact on the electrocatalytic activity, while higher concentrations impaired it. Furthermore, at a concentration of 5 mg/L Co2+, there was an increase in the proportion of the genus Anaeromusa-Anaeroarcus, while the genus Geobacter declined at all tested Co2+ concentrations. Additionally, higher concentrations of Co2+ suppressed the expression of extracellular electron transfer genes but increased the expression of Co2+-resistance genes. Overall, this study establishes how Co2+ impacts electrogenic biofilm composition, function, and treatment efficacy, laying the groundwork for the optimized application of BES in remediating Co2+-contaminated wastewater.

Fabrication and characterization of electrically conducting electrochemically synthesized polypyrrole-based enzymatic biofuel cell anode with biocompatible redox mediator vitamin K3.

Enzymatic biofuel cells (EBFCs) hold tremendous potential to power biomedical devices, biosensors, and bioelectronics. Unlike conventional toxic batteries, these electrochemical devices are biocompatible, harnessing energy from physiological fluids and producing usable electrical energy. But the commercialization of EBFCs is limited by the low operational stability, limited power output and poor electron transport efficiency of the enzymatic electrodes. In this study, a novel bioanode exhibiting a high electron transfer ability and long-term stability was fabricated. For the preparation of the anode, surfactant-assisted polypyrrole (PPy) was electrochemically co-deposited on a platinum wire with the simultaneous entrapment of vitamin K3 (VK3) and GOx (glucose oxidase) in the PPy matrix. Herein, conducting PPy acts as an electron transfer enhancer and provides appropriate electrical communication between the active site of the enzyme glucose oxidase (GOx) and the electrode surface. Biocompatible redox mediator vitamin K3 was employed as an electron transfer mediator to shuttle electrons between the oxidized fuel glucose and surface of the electrode in the electrochemical cell. The electrical conductivity of PPy was measured using the four-probe technique of conductivity measurement of semiconductors. The morphological characterization of as-synthesized anode (PPy/CTAB/VK3/GOx) was performed by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrochemical characterization was studied by cyclic voltammetry (CV), linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS) techniques. It was observed that the room-temperature conductivity of PPy lies in the semiconducting range and it also shows good stability on exposure to laboratory air, making it a promising material to provide electrical contact. The study developed a bioanode producing a modest current density of 6.35 mA cm-2 in 20 mM glucose solution. The stability, current output and ease of manufacturing process of the electrode make it particularly suitable for employment in biofuel cell applications.

Agronomic and phytotoxicity test with biosolids from anaerobic CO-DIGESTION with temperature and micro-organism phase separation, based on sewage sludge, vinasse and poultry manure.

This study deals with energy and agronomic valorisation by anaerobic co-digestion with temperature and microorganism phase separation of sewage sludge, vinasse and poultry manure, with the aim of achieving an integral waste management, obtaining bioenergy and biofertilizer that returns nutrients to the soil in a natural way. The yields obtained were 40 mL H2/gVS and 391 mLCH4/gVS. The resulting effluent showed more than 98 % removal of E. coli and Total Coliforms, as well as total removal of Salmonella. The results obtained in the phytotoxicity tests showed that all the proportions studied had phytostimulant and phytonutrient properties, with 20 % having the highest germination index (GI) with mean values of 145.30 %. Finally, the agronomic trial carried out with strawberry crops (Fragaria sp.) showed that the addition of this biosolid has fertilising properties and can be used as an agronomic amendment, with an increase of 145 % in fresh weight and 102.5 % in dry weight, and fruit production doubled with respect to the control. The ANOVA statistical study corroborated that there were significant differences in crop growth when applying different proportions of biofertilizer in the fertilizer. Therefore, these results show that this technology is promising and would contribute environmentally, socially and economically to the transfer towards a circular economy model.

Catalytic flash pyrolysis of Scenedesmus sp. post-extraction residue using low-cost HZSM-5 catalyst with the perspective to produce renewable aromatic hydrocarbons.

Recovering renewable chemicals from de-fatted microalgal residue derived from lipid extraction within the algal-derived biofuel sector is crucial, given the rising significance of microalgal-derived biodiesel as a potential substitute for petroleum-based liquid fuels. As a circular economy strategy, effective valorization of de-fatted biomass significantly improves the energetic and economic facets of establishing a sustainable algal-derived biofuel industry. In this scenario, this study investigates flash catalytic pyrolysis as a sustainable pathway for valorizing Scenedesmus sp. post-extraction residue (SPR), potentially yielding a bio-oil enriched with upgraded characteristics, especially renewable aromatic hydrocarbons. In the scope of this study, volatile products from catalytic and non-catalytic flash pyrolysis were characterized using a micro-furnace type temperature programmable pyrolyzer coupled with gas chromatographic separation and mass spectrometry detection (Py-GC/MS). Flash pyrolysis of SPR resulted in volatile products with elevated oxygen and nitrogen compounds with concentrations of 46.4% and 26.4%, respectively. In contrast, flash pyrolysis of lyophilized microalgal biomass resulted in lower concentrations of these compounds, with 40.9% oxygen and 17.3% nitrogen. Upgrading volatile pyrolysis products from SPR led to volatile products comprised of only hydrocarbons, while completely removing oxygen and nitrogen-containing compounds. This was achieved by utilizing a low-cost HZSM-5 catalyst within a catalytic bed at 500 °C. Catalytic experiments also indicate the potential conversion of SPR into a bio-oil rich in monocyclic aromatic hydrocarbons, primarily BETX, with toluene comprising over one-third of its composition, thus presenting a sustainable pathway for producing an aromatic hydrocarbon-rich bio-oil derived from SPR. Another significant finding was that 97.8% of the hydrocarbon fraction fell within the gasoline range (C5-C12), and 35.5% fell within the jet fuel range (C8-C16). Thus, flash catalytic pyrolysis of SPR exhibits significant promise for application in drop-in biofuel production, including green gasoline and bio-jet fuel, aligning with the principles of the circular economy, green chemistry, and bio-refinery.

Bioelectrochemically-assisted ammonia recovery from dairy manure.

The sustainability of direct land application of dairy manure is challenged by significant nutrient losses. Bioelectrochemical systems for ammonia recovery offer a manure management strategy that can recover both ammoniacal and organic nitrogen as a stable ammonia fertilizer. In this research, a microbial fuel cell (MFC) was used to treat two types of dairy manure under a variety of imposed anode compartment conditions. The system achieved a maximum coulombic efficiency of 20 ± 18 % and exhibited both COD and total nitrogen removals of approximately 60 %. Furthermore, the MFC showed a maximum organic nitrogen removal of 73.8 ± 12.1 %, and no differences in organic nitrogen (orgN) removal were detected among different conditions tested. Decreasing concentrations of anolyte ammonia nitrogen coupled with the observed orgN removal from the anolyte indicate that the MFC is effective at recovering orgN in dairy manure as ammoniacal nitrogen in the catholyte. Additionally, ion competition between NH4+ and other relevant cations (Na+, K+, and Mg2+) for transport across the CEM was investigated, with only K+ showing minor competitive effects. Based on the results of this research, we propose three key processes and two sub-processes that contribute to the successful operation of the MFC for nitrogen recovery from dairy manure. Bioelectrochemical systems for nitrogen recovery from dairy manure offer a novel, robust technology for producing a valuable ammonia nitrogen fertilizer, a thus far untapped resource in dairy manure streams.

Hydrogen and methane production through two stage anaerobic digestion of straw residues.

Anaerobic digestion of agricultural waste can contribute to the European renewable energy needs. The 71% of the 20,000 anaerobic digestion plants in operation already uses these agro-waste as feedstock; part of these plants can be converted into two stage processes to produce hydrogen and methane in the same plant. Biomethane enriched in hydrogen can replace natural gas in grids while contributing to the sector decarbonisation. Straw is the most abundant agricultural residue (156 Mt/y) and its conventional final fate is uncontrolled soil disposal, landfilling, incineration or, in the best cases, composting. The present research work focuses on the fermentation of spent mushroom bed, an agricultural lignocellulosic byproduct, composed mainly from wheat straw. The substrate has been characterized and semi-continuous tests were performed evaluating the effect of the hydraulic retention time on hydrogen and volatile fatty acids production. It was found that all the tests confirmed the feasibility of the process even on this lignocellulosic substrate, and also, it was identified HRT 4.0 d as the best option to optimize the productivity of volatile fatty acids (17.09 gCODVFAs/(KgVS*d)), and HRT 6.0 d for hydrogen (7.98 LH2/(KgVS*d)). The fermentation effluent was used in biomethanation potential tests to evaluate how this process affects a subsequent digestion phase, reporting an increase in the energetical feedstock exploitation up to 30%.

Investigating the impact of n-heptane (C7H16) and nanoparticles (TiO2) on diesel-microalgae biodiesel blend in CI diesel engines.

Recent global challenges encompass profound environmental pollution and the depletion of finite fuel resources. In this study, the biodiesel used in the mixture was derived from Azolla pinnata microalgae oil through a trans-esterification reaction chosen for its high oil concentration. During the initial phase of the experiment, varying volumes of biodiesel (5%, 10%, and 15%) and n-heptane (5%, 10%, and 15%) were introduced to diesel to form a ternary fuel blend. The experimental outcome shows that an n-heptane and biodiesel mixture of 10% by volume would produce the best results. Next, experiments were carried out by incorporating 10, 40, and 80 ppm titanium oxide (TiO2) nanoparticles (NPs) in a recommended ternary fuel blend. The experimental investigation showed that D80A10H10TNP40 (diesel 80% + biodiesel 10% + n-heptane 10% + TiO2 40 ppm) caused a 7.21% increase in brake thermal efficiency (BTE) with a decrease in brake specific fuel consumption (BSFC) and brake specific energy consumption (BSEC) by 9.58% and 10%, respectively, compared to (diesel 80% + biodiesel 20%) D80A20. D80A10H10TNP40 exhibits lower emissions, with a significant reduction of 11.29% and 20.96% in carbon monoxide (CO) and unburnt hydrocarbons (UBHC), respectively. Nitrogen oxide (NOX) and smoke emissions were reduced by 3.3% and 11.13%, respectively, compared to D80A10H10. Furthermore, D80A10H10TNP40 demonstrated enhanced combustion properties, comprising a significant rise of 4.39% in-cylinder pressure (CP), 35.29% in heat release rate (HRR), and 25.05% in the rate of pressure rise (RPR). The findings of this investigation indicate that D80A10H10TNP40 exhibits enhanced efficiency, emission, and combustion properties compared to the D80A20 fuel.

Fractional condensation of bio-oil vapors from pyrolysis of various sawdust wastes in a bench-scale bubbling fluidized bed reactor.

The use of lignocellulosic waste as an energy source for substituting fossil fuels has attracted lots of attention, and pyrolysis has been established as an effective technology for this purpose. However, the utilization of bio-oil derived from non-catalytic pyrolysis faces certain constraints, making it impractical for direct application in advanced sectors. This study has focused on overcoming these challenges by employing fractional condensation of pyrolytic vapors at distinct temperatures. The potential of five types of sawdust for producing high-quality bio-oil through pyrolysis conducted with a bench-scale bubbling fluidized bed reactor was investigated for the first time. The highest yield of bio-oil (61.94 wt%) was produced using sample 3 (damaged timber). Remarkably, phenolic compounds were majorly gathered in the 1st and 2nd condensers at temperatures of 200 °C and 150 °C, respectively, attributing to their higher boiling points. Whereas, carboxylic acid, ketones, and furans were mainly collected in the 3rd (-5 °C) and 4th (-20 °C) condensers, having high water content in the range of 35.33%-65.09%. The separation of acidic nature compounds such as acetic acid in the 3rd and 4th was evidenced by its low pH in the range of 4-5, while the pH of liquid collected in the 1st and 2nd condensers exhibited higher pH (6-7). The well-separated bio-oil derived from biomass pyrolysis facilitates its wide usage in various applications, proposing a unique approach toward carbon neutrality. In particular, achieving efficient separation of phenolic compounds in bio-oil is important, as these compounds can undergo further upgrading to generate hydrocarbons and diesel fuel.

Axenic green microalgae for the treatment of textile effluent and the production of biofuel: a promising sustainable approach.

An integrated approach to nutrient recycling utilizing microalgae could provide feasible solutions for both environmental control and energy production. In this study, an axenic microalgae strain, Chlorella sorokiniana ASK25 was evaluated for its potential as a biofuel feedstock and textile wastewater (TWW) treatment. The microalgae isolate was grown on TWW supplemented with different proportions of standard BG-11 medium varying from 0 to 100% (v/v). The results showed that TWW supplemented with 20% (v/v) BG11 medium demonstrated promising results in terms of Chlorella sorokiniana ASK25 biomass (3.80 g L-1), lipid production (1.24 g L-1), nutrients (N/P, > 99%) and pollutant removal (chemical oxygen demand (COD), 99.05%). The COD level dropped by 90% after 4 days of cultivation, from 2,593.33 mg L-1 to 215 mg L-1; however, after day 6, the nitrogen (-NO3-1) and total phosphorus (TP) levels were reduced by more than 95%. The biomass-, total lipid- and carbohydrate- production, after 6 days of cultivation were 3.80 g L-1, 1.24 g L-1, and 1.09 g L-1, respectively, which were 2.15-, 2.95- and 3.30-fold higher than Chlorella sorokiniana ASK25 grown in standard BG-11 medium (control). In addition, as per the theoretical mass balances, 1 tonne biomass of Chlorella sorokiniana ASK25 might yield 294.5 kg of biodiesel and 135.7 kg of bioethanol. Palmitic acid, stearic acid, and oleic acid were the dominant fatty acids found in the Chlorella sorokiniana ASK25 lipid. This study illustrates the potential use of TWW as a microalgae feedstock with reduced nutrient supplementation (20% of TWW). Thus, it can be considered a promising feedstock for economical biofuel production.

Bioconversion of citrus waste by long-term DMSO-cryopreserved rumen fluid to volatile fatty acids and biogas is feasible: A microbiome perspective.

Preserving rumen fluid as the inoculum for anaerobic digestion of food waste is necessary when access to animal donors or slaughterhouses is limited. This study aims to compare two preservation methods relative to fresh ruminal inoculum: (1) cryoprotected with 5% dimethyl sulfoxide (DMSO) and stored at -20 °C and (2) frozen at -20 °C, both for 6 months. The fermentation activity of different inoculum was evaluated by rumen-based in vitro anaerobic fermentation tests (volatile fatty acids, biomass digestibility, and gas production). Citrus pomace was used as the substrate during a 96-h fermentation. The maximum volatile fatty acids, methane production, and citrus pomace digestibility from fresh rumen fluid were not significantly different from rumen fluid preserved with DMSO. Metagenome analysis revealed a significant difference in the rumen microbial composition and functions between fresh rumen fluid and frozen inoculum without DMSO. Storage of rumen fluid using -20 °C with DMSO demonstrated the less difference compared with fresh rumen fluid in microbial alpha diversity and taxa composition. The hierarchical clustering tree of CAZymes showed that DMSO cryoprotected fluid was clustered much closer to the fresh rumen fluid, showing more similarity in CAZyme profiles than frozen rumen fluid. The abundance of functional genes associated with carbohydrate metabolism and methane metabolism did not differ between fresh rumen fluid and the DMSO-20 °C, whereas the abundance of key functional genes significantly decreased in frozen rumen fluid. These findings suggest that using rumen liquid preserved using DMSO at -20 °C for 180 days is a feasible alternative to fresh rumen fluid. This would reduce the need for laboratories to maintain animal donors and/or reduce the frequency of collecting rumen fluid from slaughterhouses.

Valorization of spent coffee grounds through integrated bioprocess of fermentable sugars, volatile fatty acids, yeast-based single-cell protein and biofuels production.

Recovering nutrients from waste for biological processes aligns with sustainability principles. This study aimed to convert spent coffee grounds (SCG) into valuable products, including fermentable sugars, volatile fatty acids (VFAs), yeast-based single-cell protein and biofuels. Alkaline pretreatment was conducted before enzymatic hydrolysis, in which the pretreated SCG was hydrolyzed with varying enzyme loadings (20-60 filter paper units (FPU)/g-solid) and solid loadings (3-15 % w/v). The hydrolyzed slurry was utilized for VFAs and hydrogen production, yielding high values of 0.66 g/g-volatile solids (VS) and 109 mL/g-VS, respectively, using an enzyme loading of 50 FPU/g-solid and a solid loading of 3 % (w/v). The derived VFAs were used to cultivate a newly isolated yeast, Candida maltosa KKU-ARY2, resulting in an accumulated protein content of 43.7 % and a biomass concentration of 4.6 g/L. This study highlights the conversion of SCG into essential components, emphasizing the benefits of waste utilization through cascade bioprocesses.

Coupling anaerobic co-digestion of winery waste and waste activated sludge with a microalgae process: Optimization of a semi-continuous system.

Wine production represents one of the most important agro-industrial sectors in Italy. Wine lees are the most significant waste in the winery industry and have high disposal and storage costs and few applications within the circular economy. In this study, anaerobic digestion and a microalgae coupled process was studied in order to treat wine lees and waste activated sludge produced within the same facility, with the aim of producing energy and valuable microalgae biomass that could be processed to recover biofuel or biostimulant. Chlorella vulgaris was cultivated on liquid digestate in a semi-continuous system without biomass recirculation. The best growth and phytoremediation performance were achieved applying a hydraulic retention time (HRT) of 20 days with a stable dry weight, lipid and protein storage of 1.85 ± 0.02 g l-1, 33.48 ± 7.54 % and 57.85 ± 10.14 % respectively. Lipid characterization highlighted the potential use in high quality biodiesel production, according to EN14214 (<12 % v/v linolenic acid). The microalgae reactor's liquid output showed high removal of ammonia (95.72 ± 2.10 %), but low organic soluble matter reduction. Further semi-continuous process optimization was carried out by increasing the time between digestate feeding and biomass recovery at HRT 10. These operative changes avoided biomass wash-out and provided a stable phytoremediation of the digestate with 84.58 ± 4.02 % ammonia removal, 33.01 ± 1.44 % sCOD removal, 38.06 ± 2.65 % of polyphenols removal.

Waste-to-energy: Co-pyrolysis of potato peel and macroalgae for biofuels and biochemicals.

Waste-to-energy conversion presents a pivotal strategy for mitigating the energy crisis and curbing environmental pollution. Pyrolysis is a widely embraced thermochemical approach for transforming waste into valuable energy resources. This study delves into the co-pyrolysis of terrestrial biomass (potato peel) and marine biomass (Sargassum angastifolium) to optimize the quantity and quality of the resultant bio-oil and biochar. Initially, thermogravimetric analysis was conducted at varying heating rates (5, 20, and 50 °C/min) to elucidate the thermal degradation behavior of individual samples. Subsequently, comprehensive analyses employing FTIR, XRD, XRF, BET, FE-SEM, and GC-MS were employed to assess the composition and morphology of pyrolysis products. Results demonstrated an augmented bio-oil yield in mixed samples, with the highest yield of 27.1 wt% attained in a composition comprising 75% potato peel and 25% Sargassum angastifolium. As confirmed by GC-MS analysis, mixed samples exhibited reduced acidity, particularly evident in the bio-oil produced from a 75% Sargassum angastifolium blend, which exhibited approximately half the original acidity. FTIR analysis revealed key functional groups on the biochar surface, including O-H, CO, and C-O moieties. XRD and XRF analyses indicated the presence of alkali and alkaline earth metals in the biochar, while BET analysis showed a surface area ranging from 0.64 to 1.60 m2/g. The favorable characteristics of the products highlight the efficacy and cost-effectiveness of co-pyrolyzing terrestrial and marine biomass for the generation of biofuels and value-added commodities.

Interchangeable modular design and operation of photo-bioreactors for Chlorella vulgaris cultivation towards a zero-waste biorefinery.

This study explores diverse cultivation modes for Chlorella vulgaris within a biorefinery at pilot scale that produces both biodiesel by transesterification of waste frying oils and syngas by gasification of organic wood waste. Given microalgae's comparatively modest biofuel yield relative to principal biorefinery products, the microalgae cultivation process is designed on the biofuels production rates. Liquid and gaseous waste streams are recycled inside the biorefinery: crude glycerol is mixed with wood to enhance the quality of syngas, wastewater is fed to microalgae so as flue gas. Also, the oil extracted from microalgae contributes to produce biodiesel and the waste cells are gasified. Considering that the optimal fit for each cultivation mode varies with the shape of the reactor, we propose a modular approach to assemble them in batteries of tubular, bubble flow, and airlift reactors, and present an operating design criterion that can fulfill the mass balance of the plant by adding/transforming the number of units inside the different batteries. Methods to adjust the operating conditions and control the operating parameters are also discussed. The designed configurations were operated recycling nominal waste streams of about 30 L d-1 of wastewater and 90 Nm3 h-1 of flue gas. Results confirm that the most advantageous one, in terms of volume per recycled waste streams, is a battery of 16 airlift reactors, operating in mixotrophic mode, with growing rate of 0.427 d-1, yield of 3.06, glycerol conversion 39 %, CO2 removal 64 % of inlet 6-10 %(mol) concentration. The same nominal waste streams can also be managed by 40 tubular reactors in almost heterotrophic conditions coupled with 12 bubble columns in autotrophic conditions; working respectively at growing rates of 0.395 d-1 and 0.362 d-1 and yields of 2.94 and 2.84. The battery of tubular reactors reached a glycerol conversion of 45 % and the array of bubble columns removed about 51 % of inlet 12-20 %(mol) CO2 concentration. A complete comparison is reported also in terms of dimensionless numbers and pumping/mixing requirements.

Co-pyrolysis of sewage sludge and biomass waste into biofuels and biochar: A comprehensive feasibility study using a circular economy approach.

Enormous annual sewage sludge (SS) volumes pose global environmental challenges owing to contamination and significant greenhouse gas emissions. Here, we investigated the economic viability of co-pyrolyzing SS and biomass waste to produce biofuels (bio-oil and gas) and biochar. Net present worth (NPW) analysis, the sale product break-even price, and sludge handling price (SHP) were used to determine the profitability of co-pyrolysis compared with SS pyrolysis alone and conventional treatment methods. In this study, the sale prices of biochar based on quality (i.e., stability, carbon sequestration effectiveness, and heavy metal content) were estimated to be 2.24, 1.44, and 0.98 CAD/kg for high-, medium-, and low-grade biochar. The bio-oil prices, estimated based on the higher heating values of bio-oil and diesel, ranged from 0.80 to 1.22 CAD/kg. Sawdust (SD) and wheat straw (WS) were the chosen co-pyrolysis feedstocks, with four mixing ratios (20, 40, 60, and 80 wt%). Economically, SD (40 wt% mixing ratio) co-pyrolysis achieved the best performance, with a maximum NPW of 8.71 million CAD. SD single and co-pyrolysis were the only profitable scenarios. Moreover, SS single pyrolysis and WS co-pyrolysis exhibited higher profitability than conventional SS treatment methods, with SHPs of 65 and 40 CAD/1000 kg dry sludge, respectively. Sensitivity analysis highlighted the dependence of economic performance on biochar and bio-oil market value. This study offers the first economic analysis of this approach and enhances our understanding of the potential of co-pyrolysis for biofuel and biochar production, providing innovative solutions for the environmental challenges of SS disposal.

Sex-specific metabolic adaptations from in utero exposure to particulate matter derived from combustion of petrodiesel and biodiesel fuels.

Maternal exposure to particulate matter derived from diesel exhaust has been shown to cause metabolic dysregulation, neurological problems, and increased susceptibility to diabetes in the offspring. Diesel exhaust is a major source of air pollution and the use of biodiesel (BD) and its blends have been progressively increasing throughout the world; however, studies on the health impact of BD vs. petrodiesel combustion-generated exhaust have been controversial in part, due to differences in the chemical and physical nature of the associated particulate matter (PM). To explore the long-term impact of prenatal exposure, pregnant mice were exposed to PM generated by combustion of petrodiesel (B0) and a 20% soy BD blend (B20) by intratracheal instillation during embryonic days 9-17 and allowed to deliver. Offspring were then followed for 52 weeks. We found that mother's exposure to B0 and B20 PM manifested in striking sex-specific phenotypes with respect to metabolic adaptation, maintenance of glucose homeostasis, and medial hypothalamic glial cell makeup in the offspring. The data suggest PM exposure limited to a narrower critical developmental window may be compensated for by the mother and/or the fetus by altered metabolic programming in a marked sex-specific and fuel-derived PM-specific manner, leading to sex-specific risk for diseases related to environmental exposure later in life.

Characterisation of synthesised trimetallic nanoparticles and its influence on anaerobic digestion of palm oil mill effluent.

The augmentation of biogas production can be achieved by incorporating metallic nanoparticles as additives within anaerobic digestion. The objective of this current study is to examine the synthesis of Fe-Ni-Zn and Fe-Co-Zn trimetallic nanoparticles using the co-precipitation technique and assess its impact on anaerobic digestion using palm oil mill effluent (POME) as carbon source. The structural morphology and size of the synthesised trimetallic nanoparticles were analysed using a range of characterization techniques, such as X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), and Energy-dispersive X-ray spectroscopy (EDX) . The average size of Fe-Ni-Zn and Fe-Co-Zn were 19-25.5 nm and 19.1-30.5 nm respectively. Further, investigation focused on examining the diverse concentrations of trimetallic nanoparticles, ranging from 0 to 50 mgL-1. The biogas production increased by 55.55% and 60.11% with Fe-Ni-Zn and Fe-Co-Zn trimetallic nanoparticles at 40 mgL-1 and 20 mgL-1, respectively. Moreover, the lowest biogas of 11.11% and 38.11% were found with 10 mgL-1 of Fe-Ni-Zn and Fe-Co-Zn trimetallic nanoparticles. The findings of this study indicated that the trimetallic nanoparticles exhibited interactions with anaerobes, thereby enhancing the degradation process of palm oil mill effluent (POME) and biogas production. The study underscores the potential efficacy of trimetallic nanoparticles as a viable supplement for the promotion of sustainable biogas generation.

Self-adhesive wearable poly (vinyl alcohol)-based hybrid biofuel cell powered by human bio-fluids.

Advancement of wearable microelectronics demands their power source with continuous energy supply, skin-integration and miniaturization. In light of poly (vinyl alcohol) (PVA) hydrogel with nontoxicity, good biocompatibility and low cost, an advanced wearable PVA-based hybrid biofuel cells (HBFCs) with high self-adhesiveness was developed. Through the reaction between PVA molecules and succinic anhydride (SAA), the carboxylated PVA (PVA/SAA) was obtained, and by incorporation with PDA as crosslinker, the self-adhesive PVA/SAA-DA hydrogel electrolytes formed by dual covalent and hydrogen bonding. With increasing SAA and PDA content, the pore size decreased, and a uniform and dense network formed, endowing the hydrogel with a relatively high absorption capacity of PBS solution of lactate as cell fuel. Meanwhile the various functional groups of hydrogel, including catechol, quinone, amino and hydroxyl groups, contributed to impressive tissue adhesion strength against pigskin under dry and wet conditions. The PVA/SAA-DA hydrogel displayed high conductive property, and the integrated PVA-based HBFC generated open circuit voltage of 0.50 V and maximum power density of 128.76 µW/cm2 in 20 mM lactate solution, which was optimized to be 0.57 V/224.85 µW/cm2 when the pore size was enlarged. The power retention reached above 70% in one week, showing long-term stability of HBFC. The PVA-based HBFC was further adhered to human skin without extra adhesive tapes to scavenge human sweat as biofuel, and the maximum power density reached 85.34 µW/cm2, while by connected with a DC-DC converter, the HBFC could power watch, exhibiting promising application potentials as wearable electronic device to provide bioelectricity.

Co-application of concentrated biogas slurry and pyroligneous liquor mitigates ammonia emission and sustainably releases ammonium from paddy soil.

Biogas production causes vast amounts of biogas slurry (BS). Application of BS to croplands can substitute chemical fertilizers while result in higher ammonia emissions. Tremendous variation of ammonium concentration in different BSs induces imprecise substitution, while concentrated BS holds higher and more stable ammonium. Pyroligneous liquor, an acidic aqueous liquid from biochar production, can be used with concentrated BS to reduce ammonia emission. However, the effects of combining concentrated BS with pyroligneous liquor on ammonia emission and soil (nitrogen) N transformation have been poorly reported. In this study, a field experiment applying concentrated BS only, or combining with 5 %, 10 %, and 20 % pyroligneous liquor (v/v) for substituting 60 % N of single rice cultivation was conducted by contrast with chemical fertilization. The results showed that substituting chemical N fertilizers with concentrated BS increased 24.6 % ammonia emission. In comparison, applying 5 %, 10 %, and 20 % pyroligneous liquor with concentrated BS reduced 4.9 %, 20.3 %, and 24.4 % ammonia emissions, respectively. Applying concentrated BS with more pyroligneous liquor preserved higher ammonium and dissolved organic carbon in floodwater, and induced higher nitrate concentration after fertilization. Whereas soil ammonium and nitrate contents were decreased along with more pyroligneous liquor application before and after the topdressing and exhibited sustainable release until rice harvest. In comparison, the soil N mineralization and nitrification rates were occasionally elevated, while the activities of soil urease, protease, nitrate reductase, and nitrite reductase had multiple responses. Applying concentrated BS only, or combining with 5 %, 10, and 20 % pyroligneous liquor, have little effect on soil basic properties but inorganic N. In summary, applying concentrated BS with >10 % pyroligneous liquor could preserve more N with sustainable release and potentially lower N loss to the atmosphere, and we proposed that applying 13.5 % pyroligneous liquor in concentrated BS could achieve maximum soil fertility and minimum ammonia emission.