Pseudoelasticity of SrNi2P2 Micropillar via Double Lattice Collapse and Expansion.

The maximum recoverable strain of most crystalline solids is less than 1% because plastic deformation or fracture usually occurs at a small strain. In this work, we show that a SrNi2P2 micropillar exhibits pseudoelasticity with a large maximum recoverable strain of ∼14% under uniaxial compression via unique reversible structural transformation, double lattice collapse-expansion that is repeatable under cyclic loading. Its high yield strength (∼3.8 ± 0.5 GPa) and large maximum recoverable strain bring out the ultrahigh modulus of resilience (∼146 ± 19 MJ/m3), a few orders of magnitude higher than that of most engineering materials. The double lattice collapse-expansion mechanism shows stress-strain behaviors similar to that of conventional shape-memory alloys, such as hysteresis and thermo-mechanical actuation, even though the structural changes involved are completely different. Our work suggests that the discovery of a new class of high-performance ThCr2Si2-structured materials will open new research opportunities in the field of pseudoelasticity.

Ion-damage-free planarization or shallow angle sectioning of solar cells for mapping grain orientation and nanoscale photovoltaic properties.

Ion beam milling is the most common modern method for preparing specific features for microscopic analysis, even though concomitant ion implantation and amorphization remain persistent challenges, particularly as they often modify materials properties of interest. Atomic force microscopy (AFM), on the other hand, can mechanically mill specific nanoscale regions in plan-view without chemical or high energy ion damage, due to its resolution, directionality, and fine load control. As an example, AFM-nanomilling (AFM-NM) is implemented for top-down planarization of polycrystalline CdTe thin film solar cells, with a resulting decrease in the root mean square (RMS) roughness by an order of magnitude, even better than for a low incidence FIB polished surface. Subsequent AFM-based property maps reveal a substantially stronger contrast, in this case of the short-circuit current or open circuit voltage during light exposure. Electron back scattering diffraction (EBSD) imaging also becomes possible upon AFM-NM, enabling direct correlations between the local materials properties and the polycrystalline microstructure. Smooth shallow-angle cross-sections are demonstrated as well, based on targeted oblique milling. As expected, this reveals a gradual decrease in the average short-circuit current and maximum power as the underlying CdS and electrode layers are approached, but a relatively consistent open-circuit voltage through the diminishing thickness of the CdTe absorber. AFM-based nanomilling is therefore a powerful tool for material characterization, uniquely providing ion-damage free, selective area, planar smoothing or low-angle sectioning of specimens while preserving their functionality. This enables novel, co-located advanced AFM measurements, EBSD analysis, and investigations by related techniques that are otherwise hindered by surface morphology or surface damage.

Focused Ion Beam Preparation of Specimens for Micro-Electro-Mechanical System-based Transmission Electron Microscopy Heating Experiments.

Micro-electro-mechanical systems (MEMS)-based heating holders offer exceptional control of temperature and heating/cooling rates for transmission electron microscopy experiments. The use of such devices is relatively straightforward for nano-particulate samples, but the preparation of specimens from bulk samples by focused ion beam (FIB) milling presents significant challenges. These include: poor mechanical integrity and site selectivity of the specimen, ion beam damage to the specimen and/or MEMS device during thinning, and difficulties in transferring the specimen onto the MEMS device. Here, we describe a novel FIB protocol for the preparation and transfer of specimens from bulk samples, which involves a specimen geometry that provides mechanical support to the electron-transparent region, while maximizing the area of that region and the contact area with the heater plate on the MEMS chip. The method utilizes an inclined stage block that minimizes exposure of the chip to the ion beam during milling. This block also allows for accurate and gentle placement of the FIB-cut specimen onto the chip by using simultaneous electron and ion beam imaging during transfer. Preliminary data from Si and Ag on Si samples are presented to demonstrate the quality of the specimens that can be obtained and their stability during in situ heating experiments.

Regenerative Electroless Etching of Silicon.

Regenerative electroless etching (ReEtching), described herein for the first time, is a method of producing nanostructured semiconductors in which an oxidant (Ox1 ) is used as a catalytic agent to facilitate the reaction between a semiconductor and a second oxidant (Ox2 ) that would be unreactive in the primary reaction. Ox2 is used to regenerate Ox1 , which is capable of initiating etching by injecting holes into the semiconductor valence band. Therefore, the extent of reaction is controlled by the amount of Ox2 added, and the rate of reaction is controlled by the injection rate of Ox2 . This general strategy is demonstrated specifically for the production of highly luminescent, nanocrystalline porous Si from the reaction of V2 O5 in HF(aq) as Ox1 and H2 O2 (aq) as Ox2 with Si powder and wafers.

Modified Mesoporous Silica for Efficient Siloxane Capture.

In this study, octamethylcyclotetrasiloxane (D4) was removed by using a novel modified solid adsorbent of mesoporous silica. The adsorbent was synthesized using inverse micelles with some modifications in the synthesis process (temperature of gelation) and in the post treatment conditions (calcination temperature and heating rate) with a concomitant improvement of D4 uptake. This is the first report on regulating the textural properties of the mesoporous silica material UCT-14 to develop an active silica adsorbent. These adjustments resulted in an increase of the silica surface area from 391 to 798 m(2)·g(-1), which leads to a high capacity (686 mg·g(-1)) of D4-capture for the silica synthesized at 80 °C, calcined at 450 °C with the heating rate of 100 °C·min(-1) (Si-Syn80). This adsorbent showed comparable adsorption performance with the widely used commercial silica gel under dry and humid condition. Recyclability tests on the commercial silica gel and mesoporous silica synthesized at 120 °C and calcined at 450 °C with a heating rate of 100 °C·min(-1) (called Si-Syn120 or Si-450 or Si-100 °C·min(-1)) indicated that the Si-Syn120 (capacity drop 10%) is more efficient than silica gel (capacity drop 15%) after three cycles. Although, the presence of moisture (25%) in the nitrogen gas stream led to capacity reduction in both Si-Syn120 and commercial silica gel, the modified UCT-14 shows slightly better resistance to humid condition.

Substrate control of anisotropic resistivity in heteroepitaxial nanostructured arrays of cryptomelane manganese oxide on strontium titanate.

Resistivity and resistance measurements have been carried out for thin films of cryptomelane-type manganese oxide (OMS-2) grown onto (001), (110), and (111)STO single crystals substrates via pulsed laser deposition. While the symmetries of the (001) and (111)STO substrate surfaces give deposits consisting of multiple nanofiber arrays with isotropic in-plane resistivities, only a single nanofiber array is formed on (110)STO giving highly anisotropic electrical properties with very low resistivity values measured parallel to the fibers and similar to the lowest value ever reported.

Nanostructured arrays of semiconducting octahedral molecular sieves by pulsed-laser deposition.

Cryptomelane-type manganese oxide (OMS-2) has been widely used to explore the semiconducting and catalytic properties of molecular sieves with mixed-valent frameworks. Selective synthesis of patterned thin films of OMS-2 with hierarchical nanostructures and oriented crystals is challenging owing to difficulties in preserving the mixed valence, porosity and crystalline phase. Here, we report that pulsed-laser ablation of OMS-2 in an oxygen-rich medium produces a three-dimensional nanostructured array of parallel and inclined OMS-2 fibres on bare substrates of (001) single-crystal strontium titanate. Both parallel and inclined OMS-2 fibres elongate along the [001](OMS-2) direction. The parallel fibres interact strongly with the substrate and grow epitaxially along <110>(STO) with lattice misfits of less than 4%, whereas the inclined fibres are oriented with (301) parallel to the substrate surface. The spontaneous orientation of the crystalline OMS-2 domains over the STO surface opens up a new avenue in lattice-engineered synthesis of multilayer materials.

Controlling the Nature of Etched Si Nanostructures: High- versus Low-Load Metal-Assisted Catalytic Etching (MACE) of Si Powders.

Metal-assisted catalytic etching (MACE) involving Ag deposited on Si particles has been reported as a facile method for the production of Si nanowires (Si NWs). We show that the structure of Si particles subjected to MACE changes dramatically in response to changing the loading of the Ag catalyst. The use of acetic acid as a surfactant and controlled injection of AgNO3(aq) enhanced Ag deposition. The use of acetic acid and controlled injection of H2O2 not only facilitated optimization of the etching step but also allowed us to identify a previously unobserved etching regime that we denote as low-load MACE (LL-MACE). Material produced by LL-MACE exhibits dramatically different yield and structural characteristics as compared to conventionally produced material. We demonstrate the production of Si NWs as well as mesoporous Si nanoparticles from an inexpensive metallurgical-grade Si powder. High loading of Ag (HL-MACE) generates parallel etch track pores created by the correlated motion of Ag nanoparticles. The uniform size distribution (predominantly 70-100 nm) of the Ag nanoparticles is generated dynamically during etching. The walls of these etch track pores are cleaved readily by ultrasonic agitation to form Si NWs. Low loading of Ag (LL-MACE) creates 10-50 nm Ag nanoparticles that etch in an uncorrelated (randomly directed) fashion to generate a bimodal distribution of mesoporosity peaking at ∼4 and 13-21 nm. The use of a syringe pump to deliver the oxidant (H2O2) and Ag+ is essential for increased product uniformity and yield. Different process temperatures and grades of Si produced significantly different pore size distributions. These results facilitate the production of Si NWs and mesoporous nanoparticles with high yield, low cost, and controlled properties that are suitable for applications in, e.g., lithium-ion batteries, drug delivery, as well as biomedical imaging and contrast enhancement.

Low-Load Metal-Assisted Catalytic Etching Produces Scalable Porosity in Si Powders.

The recently discovered low-load metal-assisted catalytic etching (LL-MACE) creates nanostructured Si with controllable and variable characteristics that distinguish this technique from the conventional high-load variant. LL-MACE employs 150 times less metal catalyst and produces porous Si instead of Si nanowires. In this work, we demonstrate that some of the features of LL-MACE cannot be explained by the present understanding of MACE. With mechanistic insight derived from extensive experimentation, it is demonstrated that (1) the method allows the use of not only Ag, Pd, Pt, and Au as metal catalysts but also Cu and (2) judicious combinations of process parameters such as the type of metal, Si doping levels, and etching temperatures facilitate control over yield (0.065-88%), pore size (3-100 nm), specific surface area (20-310 m2·g-1), and specific pore volume (0.05-1.05 cm3·g-1). The porous structure of the product depends on the space-charge layer, which is controlled by the Si doping and the chemical identity of the deposited metal. The porous structure was also dependent on the dynamic structure of the deposited metal. A distinctive comet-like structure of metal nanoparticles was observed after etching with Cu, Ag, Pd, and, in some cases, Pt; this structure consisted of 10-50 nm main particles surrounded by smaller (<5 nm) nanoparticles. With good scalability and precise control of structural properties, LL-MACE facilitates Si applications in photovoltaics, energy storage, biomedicine, and water purification.

Temperature calibration of TEM specimen heating holders by isothermal sublimation of silver nanocubes.

Micro electro mechanical systems (MEMS) based TEM specimen heating holders exhibit excellent thermal stability and minimal specimen drift, which allows thermally-activated processes to be studied dynamically at high spatial resolution. The advantages of MEMS-based devices arise from the very small thermal masses of the sample studied, but this poses particular challenges for the precise measurement of specimen temperature. Previously, it has been proposed that the size-dependent sublimation behavior of Ag nanoparticles could be used to measure the specimen temperature by applying the Kelvin equation, but the effects of the capping ligands used in the nanoparticle synthesis and of electron beam heating have limited the application of such approaches. Here it is shown that for an appropriate choice of experimental parameters (nanoparticle size, loading, intermediate holding temperature, and illumination conditions) the sublimation of Ag nano-cubes can be used to measure the specimen temperature to an accuracy of ±5 °C, over the range 700-850 °C. The measurements are reproducible from area to area on the same MEMS chip, and from chip to chip of the same type. The values of specimen temperature obtained are consistently lower than the calibrated MEMS heater plate temperatures, and it is shown that this cannot be explained on the basis of random errors in the experimental measurements or systematic errors in the materials parameters used for the Kelvin equation analysis. It is proposed that this is instead due to the low thermal conductivity of the electron-transparent amorphous silicon nitride support membrane on the chip. As further evidence for this, it is shown that for a thicker crystalline Si support with a higher thermal conductivity, the magnitude of the difference is smaller. This approach could be extended to other temperature ranges by using nanoparticles of other metals with different vapor pressures and sublimation temperatures.

Hierarchical Nanostructuring of Porous Silicon with Electrochemical and Regenerative Electroless Etching.

Hierarchically nanostructured silicon was produced by regenerative electroless etching (ReEtching) of Si powder made from pulverized anodized porous silicon. This material is characterized by ∼15 nm mesopores, into the walls of which tortuous 2-4 nm pores have been introduced. The walls are sufficiently narrow that they support quantum-confined crystallites that are photoluminescent. With suitable parameters, the ReEtching process also provides control over the emission color of the photoluminescence. Ball milling and hydrosilylation of this powder with undecylenic acid produces nanoparticles with hydrodynamic diameter of ∼220 nm that exhibit robust and bright luminescence that can be excited with either one ultraviolet/visible photon or two near-infrared photons. The long-lived, robust visible photoluminescence of these chemically passivated porous silicon nanoparticles is well-suited for bioimaging and theranostic applications.

Effect of transition metal alloying elements on the deformation of Ti-44Al-8Nb-0.2B-0.2Y alloys.

A series of ß-γ Ti-44Al-8Nb-0.2B-0.2Y alloys have been modified with 0.5 to 2.0 at.% of the ß-stabilizing elements Mn, Cr, Mo and V. Additions of Cr and Mo alone result in a decrease in the flow stress, whereas the opposite effect was observed for additions of V. For alloys with Mn additions, a minimum value of the flow stress was achieved in the alloy with 1.5% Mn. For alloys with combined additions, optimum hot deformation behavior was obtained for the alloy with 1.5% Mn and 1.0% Cr.

Crystallographically Determined Etching and Its Relevance to the Metal-Assisted Catalytic Etching (MACE) of Silicon Powders.

Metal-assisted catalytic etching (MACE) using Ag nanoparticles as catalysts and H2O2 as oxidant has been performed on single-crystal Si wafers, single-crystal electronics grade Si powders, and polycrystalline metallurgical grade Si powders. The temperature dependence of the etch kinetics has been measured over the range 5-37°C. Etching is found to proceed preferentially in a 〈001〉 direction with an activation energy of ~0.4 eV on substrates with (001), (110), and (111) orientations. A quantitative model to explain the preference for etching in the 〈001〉 direction is developed and found to be consistent with the measured activation energies. Etching of metallurgical grade powders produces particles, the surfaces of which are covered primarily with porous silicon (por-Si) in the form of interconnected ridges. Silicon nanowires (SiNW) and bundles of SiNW can be harvested from these porous particles by ultrasonic agitation. Analysis of the forces acting between the metal nanoparticle catalyst and the Si particle demonstrates that strongly attractive electrostatic and van der Waals interactions ensure that the metal nanoparticles remain in intimate contact with the Si particles throughout the etch process. These attractive forces draw the catalyst toward the interior of the particle and explain why the powder particles are etched equivalently on all the exposed faces.

Constitutive modeling of high temperature flow behavior in a Ti-45Al-8Nb-2Cr-2Mn-0.2Y alloy.

A constitutive equation based on the hyperbolic sinusoidal Arrhenius-type model has been developed to describe the hot deformation behavior of a ß-γ Ti-Al alloy containing 8 at.% of Nb. Experimental true stress-true strain data were acquired from isothermal hot compression tests conducted across a wide range of temperatures (1273 K~1473 K) and strain rates (0.001 s-1~1 s-1), and the changes in the experimental conditions were reflected in the values of the Zener-Hollomon parameter. The impact of true strain was expressed through material constants (A, α, n and Q), and it was found that a 7th order polynomial is appropriate to express the relations between the true strain and these material constants. The average absolute relative error (AARE) and correlation coefficient (R) were used to evaluate the accuracy of the constitutive equation, and the values obtained were 6.009% and 0.9961, respectively. These results indicate that the type of constitutive equation developed here can predict the flow stress for this alloy with good accuracy over a wide range of experimental conditions. Thus, equations of this form could be applied more widely to analyses of hot deformation mechanism and microstructure evolution.

Unraveling the Mesoscale Evolution of Microstructure during Supersonic Impact of Aluminum Powder Particles.

A critical challenge in the predictive capability of materials deformation behavior under extreme environments is the availability of computational methods to model the microstructural evolution at the mesoscale. The capability of the recently-developed quasi-coarse-grained dynamics (QCGD) method to model mesoscale behavior is demonstrated for the phenomenon of supersonic impact of 20 µm sized Al particles on to an Al substrate at various impact velocities and over time and length scales relevant to cold spray deposition. The QCGD simulations are able to model the kinetics related to heat generation and dissipation, and the pressure evolution and propagation, during single particle impact over the time and length scales that are important experimentally. These simulations are able to unravel the roles of particle and substrate deformation behavior that lead to an outward/upward flow of both the particle and the substrate, which is a likely precursor for the experimentally observed jetting and bonding of the particles during cold spray impact.

Strong, ductile, and thermally stable Cu-based metal-intermetallic nanostructured composites.

Bulk metallic glasses (BMGs) and nanocrystalline metals (NMs) have been extensively investigated due to their superior strengths and elastic limits. Despite these excellent mechanical properties, low ductility at room temperature and poor microstructural stability at elevated temperatures often limit their practical applications. Thus, there is a need for a metallic material system that can overcome these performance limits of BMGs and NMs. Here, we present novel Cu-based metal-intermetallic nanostructured composites (MINCs), which exhibit high ultimate compressive strengths (over 2 GPa), high compressive failure strain (over 20%), and superior microstructural stability even at temperatures above the glass transition temperature of Cu-based BMGs. Rapid solidification produces a unique ultra-fine microstructure that contains a large volume fraction of Cu5Zr superlattice intermetallic compound; this contributes to the high strength and superior thermal stability. Mechanical and microstructural characterizations reveal that substantial accumulation of phase boundary sliding at metal/intermetallic interfaces accounts for the extensive ductility observed.

Preparation and characterization of ruthenium/carbon aerogel nanocomposites via a supercritical fluid route.

Carbon-aerogel-supported ruthenium nanoparticles were synthesized by impregnating carbon aerogels with Ru(acac)3 or Ru(cod)(tmhd)2 from supercritical carbon dioxide (scCO2) solutions, followed by thermal reduction of these precursors. Two different carbon aerogels with pore diameters of 4 and 21 nm were synthesized. The kinetics and the thermodynamics of impregnation of carbon aerogels with the ruthenium coordination complexes were studied. The approach-to-equilibrium data indicated very fast adsorption, and the adsorption isotherms were found to follow the Langmuir model. The impregnated carbon aerogel complexes were reduced thermally at different temperatures between 300 and 1000 degrees C in the presence of nitrogen. The resulting nanocomposites were characterized using transmission electron microscopy (TEM) and hydrogen chemisorption. TEM micrographs showed that the ruthenium nanoparticles were dispersed homogeneously throughout the porous carbon aerogel matrix, and the average sizes obtained under different conditions ranged from 1.7 to 3.8 nm. Once complete decomposition of the precursor had been achieved, the mean size of the ruthenium particles increased with increasing reduction temperature.

Facet-dependent catalytic activity of MnO electrocatalysts for oxygen reduction and oxygen evolution reactions.

This Communication highlights the facet-dependent electrocatalytic activity of MnO nanocrystals for OERs/ORRs. The MnO(100) facets with higher adsorption energy of O species can largely promote the electrocatalytic activity.

In situ synthesis of mixed-valent manganese oxide nanocrystals: an in situ synchrotron X-ray diffraction study.

Phase transformations of materials can be studied by in situ synchrotron X-ray diffraction. However, most reported in situ synchrotron XRD studies focus on solid state/gel systems by measuring phase/structure changes during application of pressure or heat. Phase transformations during material synthesis and their applications, especially in wet chemistry processes with different media, have not drawn much attention. Here, using manganese oxides as examples, we report the successful characterization of phase transformations in in situ hydrothermal synthesis conditions by the in situ synchrotron XRD method using a quartz/sapphire capillary tube as the synthesis reactor. The results were used for better design of materials with controlled structures and properties. This method can be generally used for synthesis of manganese oxides as well as for in situ characterization of other material syntheses using hydrothermal, sol-gel, and other methods. In addition, catalytic processes in liquid-solid, gas-solid, and solid-solid systems can also be studied in such an in situ way so that catalytic mechanisms can be better understood and catalyst synthesis and catalytic processes can be optimized.