Evaluation of Polyvinyl Alcohol as Binder during Continuous Twin Screw Wet Granulation.

Binder selection is a crucial step in continuous twin-screw wet granulation (TSWG), as the material experiences a much shorter residence time (2-40 s) in the granulator barrel compared to batch-wise granulation processes. Polyvinyl alcohol (PVA) 4-88 was identified as an effective binder during TSWG, but the potential of other PVA grades-differing in polymerization and hydrolysis degree-has not yet been studied. Therefore, the aim of the current study was to evaluate the potential of different PVA grades as a binder during TSWG. The breakage and drying behavior during the fluidized bed drying of drug-loaded granules containing the PVA grades was also studied. Three PVA grades (4-88, 18-88, and 40-88) were characterized and their attributes were compared to previously investigated binders by Vandevivere et al. through principal component analysis. Three binder clusters could be distinguished according to their attributes, whereby each cluster contained a PVA grade and a previously investigated binder. PVA 4-88 was the most effective binder of the PVA grades for both a good water-soluble and water-insoluble formulation. This could be attributed to its high total surface energy, low viscosity, good wettability of hydrophilic and hydrophobic surfaces, and good wettability by water of the binder. Compared to the previously investigated binders, all PVA grades were more effective in the water-insoluble formulation, as they yielded strong granules (friability below 30%) at lower L/S-ratios. This was linked to the high dispersive surface energy of the high-energy sites on the surface of PVA grades and their low surface tension. During fluidized bed drying, PVA grades proved suitable binders, as the acetaminophen (APAP) granules were dried within a short time due to the low L/S-ratio, at which high-quality granules could be produced. In addition, no attrition occurred, and strong tablets were obtained. Based on this study, PVA could be the preferred binder during twin screw granulation due to its high binder effectiveness at a low L/S-ratio, allowing efficient downstream processing. However, process robustness must be controlled by the included excipients, as PVA grades are operating in a narrow L/S-ratio range.

Biodistribution of polysorbate 80-coated doxorubicin-loaded [14C]-poly(butyl cyanoacrylate) nanoparticles after intravenous administration to glioblastoma-bearing rats.

It was recently shown that doxorubicin (DOX) bound to polysorbate-coated nanoparticles (NP) crossed the intact blood-brain barrier (BBB), and thus reached therapeutic concentrations in the brain. Here, we investigated the biodistribution in the brain and in the body of poly(butyl-2-cyano[3-(14)C]acrylate) NP ([(14)C]-PBCA NP), polysorbate 80 (PS 80)-coated [(14)C]-PBCA NP, DOX-loaded [(14)C]-PBCA NP in glioblastoma 101/8-bearing rats after i.v. injection. The biodistribution profiles and brain concentrations of radiolabeled NP were determined by radioactivity counting after i.v. administration in rats. Changes in BBB permeability after tumour inoculation were assessed by i.v. injection of Evans Blue solution. The accumulation of NP in the tumour site and in the contralateral hemisphere in glioblastoma bearing-rats probably was augmented by the enhanced permeability and retention effect (EPR effect) that may have been becoming instrumental due to the impaired BBB on the NP delivery into the brain. The uptake of the NP by the organs of the reticuloendothelial system (RES) was reduced after PS 80-coating, but the addition of DOX increased again the concentration of NP in the RES.

Body distribution of polysorbate-80 and doxorubicin-loaded [14C]poly(butyl cyanoacrylate) nanoparticles after i.v. administration in rats.

Previously it was shown that poly(butyl cyanoacrylate) (PBCA) nanoparticles coated with polysorbate 80 are able to cross the blood-brain barrier (BBB) after i.v. administration. The objective of the present study was to investigate the influence of polysorbate 80 and doxorubicin-loading on the body distribution in rats. The biodistribution profile and brain concentration of (14)C-radiolabeled PBCA nanoparticles, polysorbate 80 coated (14)C-PBCA nanoparticles, and doxorubicin-loaded (14)C-PBCA nanoparticles were determined by radioactivity counting after i.v. administration in rats. The (14)C-PBCA nanoparticles showed a significant accumulation in the organs of the reticuloendothelial system (RES). Polysorbate 80 coating of the (14)C-PBCA nanoparticles decreased this accumulation to about 40% after 1 h post injection. The brain concentration was increased about 2-fold after polysorbate 80-coating at this time point. The presence of doxorubicin in this preparation, however, decreased the brain concentration to levels similar to uncoated particles, probably caused by the positive charge of this compound. After longer time periods after injection the differences between the three preparations decreased.

Influence of surfactants, polymer and doxorubicin loading on the anti-tumour effect of poly(butyl cyanoacrylate) nanoparticles in a rat glioma model.

Poly(n-butyl cyanoacrylate) nanoparticles coated with polysorbate-80 can enable the transport of bound drugs across the blood-brain barrier (BBB) after i.v. injection. In the present study the influence of different formulation parameters on the anti-tumoural effects of doxorubicin nanoparticles against glioblastoma 101/8 was investigated. The manufacturing parameters of poly(alkyl cyanoacrylate) doxorubicin-loaded nanoparticles were optimized concerning drug loading. The nanoparticles were coated with different surfactants and injected intravenously on days 2, 5 and 8 after intra-cranial implantation of glioblastoma 101/8 to rats. The survival times of all doxorubicin containing preparations, including a doxorubicin solution, increased the survival times significantly compared to untreated tumour-bearing rats. The most pronounced increase in survival was obtained with the poly(n-butyl cyanoacrylate) doxorubicin-loaded nanoparticles coated with polysorbate 80 and 35% of these animals survived for over 180 days (termination of the experiments). The other nanoparticle preparations yielded lower survival times. Poly(n-butyl cyanoacrylate) doxorubicin-loaded nanoparticles coated with polysorbate 80-coated proved to be very efficient against glioblastoma 101/8. The data suggest that the interaction of nanoparticles with the blood after injection as well as the enhanced permeability and retention effect (EPR effect) contributed differently to the anti-tumoural efficacy depending on nanoparticle formulation and surface properties.