Performance evaluation of a UOWC system based on the FRS/OCDMA code for different types of Jerlov waters.

In this work, the fixed right shift (FRS) code is utilized for the optical code division multiple access (OCDMA) technique in an underwater optical wireless communication (UOWC) system. Additionally, in this system, a 532 nm laser diode (LD) source is employed to generate optical signals. The investigation encompasses an analysis of five distinct Jerlov water types, each exhibiting diverse chlorophyll concentrations. The performance of the proposed system is evaluated when each channel that is assigned a unique FRS code sequence carries different data rates (2.5, 5, and 10 Gbps). Underwater (UW) ranges, bit error rate (BER), eye diagrams, and quality factor (Q-factor) are the performance metrics used to evaluate the system performance. The proposed UOWC-FRS/OCDMA system is simulated, and the obtained results show that the eye diagram openings close, the BER increases, and the Q-factor decreases as the data rate per each channel increases from 2.5 to 10 Gbps, and the attenuation of water becomes higher. Moreover, the lower attenuation values caused by the Jerlov type I (JI) waterbody allow each channel to carry 10 Gbps of data to propagate longer UW for a range of 35 m with a log(BER) ≤-6.33 and Q-factor greater than 4.9. On the other hand, at the same values of BER and Q-factor, the shortest ranges of 12 and 5.15 m are obtained for JII and JIII waters, respectively, where their attenuation coefficient values are 0.5297 (JII) and 1.8998 m -1 (JIII). Furthermore, as our model uses three channels, the overall achieved capacity is 3×10G b p s=30G b p s.

Circular Optical Phased Array with Large Steering Range and High Resolution.

Light detection and ranging systems based on optical phased arrays and integrated silicon photonics have sparked a surge of applications over the recent years. This includes applications in sensing, free-space communications, or autonomous vehicles, to name a few. Herein, we report a design of two-dimensional optical phased arrays, which are arranged in a grid of concentric rings. We numerically investigate two designs composed of 110 and 820 elements, respectively. Both single-wavelength (1550 nm) and broadband multi-wavelength (1535 nm to 1565 nm) operations are studied. The proposed phased arrays enable free-space beam steering, offering improved performance with narrow beam divergences of only 0.5° and 0.22° for the 110-element and 820-element arrays, respectively, with a main-to-sidelobe suppression ratio higher than 10 dB. The circular array topology also allows large element spacing far beyond the sub-wavelength-scaled limits that are present in one-dimensional linear or two-dimensional rectangular arrays. Under a single-wavelength operation, a solid-angle steering between 0.21π sr and 0.51π sr is obtained for 110- and 820-element arrays, respectively, while the beam steering spans the range of 0.24π sr and 0.57π sr for a multi-wavelength operation. This work opens new opportunities for future optical phased arrays in on-chip photonic applications, in which fast, high-resolution, and broadband beam steering is necessary.

Comparison of different schemes for stimulated Brillouin scattering enhancement.

A comparison of different schemes to enhance stimulated Brillouin Scattering (SBS) in single-mode optical fiber is performed. Specifically, we evaluated SBS generation efficiency in a 3 km length fiber with and without power recycling versus the same fiber placed in a ring resonator and in a ring resonator in a recycling configuration. For the latter case, a large number of both odd and even higher-order Stokes and anti-Stokes harmonics is generated. We show that the choice of the scheme is dictated by specific application. In addition, when incorporating a ring resonator in a Sagnac loop, a flat optical frequency comb is generated.

Performance Investigations of InAs/InP Quantum-Dash Semiconductor Optical Amplifiers with Different Numbers of Dash Layers.

We present here a performance comparison of quantum-dash (Qdash) semiconductor amplifiers (SOAs) with three, five, eight, and twelve InAs dash layers grown on InP substrates. Other than the number of Qdash layers, the structures were identical. The eight-layer Qdash SOA gave the highest amplified spontaneous emission power (4.3 dBm) and chip gain (26.4 dB) at 1550 nm, with a 300 mA CW bias current and at 25 °C temperature, while SOAs with fewer Qdash layers (for example, three-layer Qdash SOA), had a wider ASE bandwidth (90 nm) and larger 3 dB gain saturated output power (18.2 dBm) in a shorter wavelength range. The noise figure (NF) of the SOAs increased nearly linearly with the number of Qdash layers. The longest gain peak wavelength of 1570 nm was observed for the 12-layer Qdash SOA. The most balanced performance was obtained with a five-layer Qdash SOA, with a 25.4 dB small-signal chip gain, 15.2 dBm 3 dB output saturated power, and 5.7 dB NF at 1532 nm, 300 mA and 25 °C. These results are better than those of quantum well SOAs reported in a recent review paper. The high performance of InAs/InP Qdash SOAs with different Qdash layers shown in this paper could be important for many applications with distinct requirements under uncooled scenarios.

Circular Optical Phased Arrays with Radial Nano-Antennas.

On-chip optical phased arrays (OPAs) are the enabling technology for diverse applications, ranging from optical interconnects to metrology and light detection and ranging (LIDAR). To meet the required performance demands, OPAs need to achieve a narrow beam width and wide-angle steering, along with efficient sidelobe suppression. A typical OPA configuration consists of either one-dimensional (1D) linear or two-dimensional (2D) rectangular arrays. However, the presence of grating sidelobes from these array configurations in the far-field pattern limits the aliasing-free beam steering, when the antenna element spacing is larger than half of a wavelength. In this work, we provide numerical analysis for 2D circular OPAs with radially arranged nano-antennas. The circular array geometry is shown to effectively suppress the grating lobes, expand the range for beam steering and obtain narrower beamwidths, while increasing element spacing to about 10 µm. To allow for high coupling efficiency, we propose the use of a central circular grating coupler to feed the designed circular OPA. Leveraging radially positioned nano-antennas and an efficient central grating coupler, our design can yield an aliasing-free azimuthal field of view (FOV) of 360°, while the elevation angle FOV is limited by the far-field beamwidth of the nano-antenna element and its array arrangement. With a main-to-sidelobe contrast ratio of 10 dB, a 110-element OPA offers an elevation FOV of 5° and an angular beamwidth of 1.14°, while an 870-element array provides an elevation FOV up to 20° with an angular beamwidth of 0.35°. Our analysis suggests that the performance of the circular OPAs can be further improved by integrating more elements, achieving larger aliasing-free FOV and narrower beamwidths. Our proposed design paves a new way for the development of on-chip OPAs with large 2D beam steering and high resolutions in communications and LIDAR systems.

Design and Analysis of an O+E-Band Hybrid Optical Amplifier for CWDM Systems.

Broadband amplification in the O+E-band is very desirable nowadays as a way of coping with increasing bandwidth demands. The main issue with doped fiber amplifiers working in this band such as the bismuth-doped fiber amplifier is that they are costly and not widely available. Therefore, a wideband and flat-gain hybrid optical amplifier (HOA) covering the O+E-band based on a parallel combination of a praseodymium-doped fiber amplifier (PDFA) and a semiconductor optical amplifier (SOA) is proposed and demonstrated through numerical simulations. The praseodymium-doped fiber (PDF) core is pumped using a laser diode with a power of 500 mW that is centered at a wavelength of 1030 nm. The SOA is driven by an injection current of 60 mA. The performance of the HOA is analyzed by the optimization of various parameters such as the PDF length, Pr3+ concentration, pump wavelength, and injection current. A flat average gain of 24 dB with a flatness of 1 dB and an output power of 9.6 dBm is observed over a wavelength range of 1270-1450 nm. The noise figure (NF) varies from a minimum of 4 dB to a maximum of 5.9 dB for a signal power of 0 dBm. A gain reduction of around 4 dB is observed for an O-band signal at a wavelength of 1290 nm by considering the up-conversion effect. The transmission performance of the designed HOA as a pre-amplifier is evaluated based on the bit-error rate (BER) analysis for a coarse wavelength-division multiplexing (CWDM) system of eight on-off keying (OOK)-modulated channels, each having a data rate of 10 Gbps. An error-free transmission over 60 km of standard single-mode fiber (SMF) is achieved for different data rates of 5 Gbps, 7.5 Gbps, and 10 Gbps.

Partial bit delay correlative modulation used to improve the dispersion tolerance of an optical duobinary system.

Phase effect of the optical duobinary (ODB) modulation on the chromatic dispersion (CD) tolerance is more important than the ODB modulation-induced bandwidth effect. To show this, we evaluate, respectively, the filter bandwidth effect and the phase effect of the partial bit delay correlative modulation (PBDCM) on the CD tolerance. Due to the cancellation between the CD-induced and the PBDCM-induced phase effects, the PBDCM method can increase the CD-limited transmission to 2 ??? 3 times of that using standard 1-bit delay modulation, while the optimized filter bandwidth method can increase the transmission by 50% or less, depending on the input signal format. The PBDCM can be physically realized by adjusting the delay time of the delay-and-add circuit in the conventional duobinary transmitter (without lower-pass filter). These conclusions are also valid for systems having non-negligible polarization-mode dispersion (PMD) and polarization dependent loss (PDL).

Platform switching for marginal bone preservation around dental implants: a systematic review and meta-analysis.

BACKGROUND: Platform switching for maintaining peri-implant bone levels has gained popularity among implant manufacturers over the last few years. However, the assumption that the inward shifting of the implant-abutment junction may preserve crestal bone was primarily based on serendipitous finding rather than scientific evidence. The objectives of the present study were to systematically review radiographic marginal bone-level changes and the survival of platform-switched implants compared to conventional platform-matched implants. METHODS: A literature search of electronic databases (MEDLINE, EMBASE, The Cochrane Oral Health Group's Trials Register, The Cochrane Central Register of Controlled Trials, the U.K. National Research Register, the Australian New Zealand Clinical Trials Registry, the Database of Abstracts of Reviews of Effectiveness, and Conference Proceedings Citation Index) was performed up to March 15, 2010. Hand searches included several dental journals, and authors were contacted for missing information. Controlled trials that compared marginal bone-level changes around platform-switched dental implants with those restored with platform-matched prostheses were selected. The review and meta-analysis were done according to the guidelines of the Preferred Reporting Items for Systematic Reviews and Meta-Analyses statement. Data were analyzed using two meta-analytic statistical packages. Mean differences (MDs) were calculated for analyzing continuous data, and risk ratios (RRs) were used for dichotomous data with 95% confidence intervals (CIs). RESULTS: Ten studies with 1,239 implants were included. The marginal bone loss around platform-switched implants was significantly less than around platform-matched implants (MD: -0.37; 95% CI: -0.55 to -0.20; P <0.0001). No statistically significant difference was detected for implant failures between the two groups (RR: 0.93; 95% CI: 0.34 to 2.95; P = 0.89). Subgroup analyses showed that an implant-abutment diameter difference > or= 0.4 was associated with a more favorable bone response. CONCLUSIONS: The review and meta-analysis show that platform switching may preserve interimplant bone height and soft tissue levels. The degree of marginal bone resorption is inversely related to the extent of the implant-abutment mismatch. Further long-term, well-conducted, randomized controlled studies are needed to confirm the validity of this concept.

Immediate loading with single implant crowns: a systematic review and meta-analysis.

PURPOSE: A systematic review and meta-analysis of studies that specifically compared immediate to conventional loading of single implant crowns was conducted and the overall treatment effect was estimated. MATERIALS AND METHODS: MEDLINE, the Cochrane Controlled Trials Register, and bibliographies of relevant primary and review articles were searched. Randomized and nonrandomized controlled studies that compared immediate with conventional loading of single implant crowns were selected according to strict criteria. From the 105 articles screened, five studies with 248 implants were analyzed. The meta-analysis was prepared in accordance with the Quality of Reporting of Meta-analyses (QUOROM) statement. Descriptive and outcome data were extracted using specially designed data extraction forms. The data were entered into MIX software for meta-analysis using a fixed effects model, relative risk, and 95% confidence interval (CI). RESULTS: Immediate loading of single implant crowns was associated with a significantly higher risk of implant failure (relative risk: 5.07, 95% CI: 2.00 to 12.84, P < .001). Pooling of randomized controlled trials showed similar results, although the difference was not statistically significant. Immediate nonocclusal loading was also associated with worse outcomes when compared to conventional loading (relative risk: 4.76, 95% CI: 1.74 to 13.02, P = .002). CONCLUSIONS: This systematic review and meta-analysis shows that better outcomes are currently achieved using conventional loading of single implants with crowns, as opposed to immediately loaded ones, which are at a higher risk of failure. Further adequately powered clinical trials are needed. Caution with immediate loading of implants with crowns as a standard of care for single tooth replacement is recommended.