RESUMO
Optically resonant high-index dielectric metasurfaces featuring Mie-type electric and magnetic resonances are usually fabricated by means of planar technologies, which limit the degrees of freedom in tunability and scalability of the fabricated systems. Therefore, we propose a complimentary post-processing technique based on ultrashort (≤ 10 ps) laser pulses. The process involves thermal effects: crystallization and reshaping, while the heat is localized by a high-precision positioning of the focused laser beam. Moreover, for the first time, the resonant behavior of dielectric metasurface elements is exploited to engineer a specific absorption profile, which leads to a spatially-selective heating and a customized modification. Such technique has the potential to reduce the complexity in the fabrication of non-uniform metasurface-based optical elements. Two distinct cases, a spatial pixelation of a large-scale metasurface and a height modification of metasurface elements, are explicitly demonstrated.
RESUMO
We present a planar spectro-polarimeter based on Fabry-Pérot cavities with embedded polarization-sensitive high-index nanostructures. A 7 µm-thick spectro-polarimetric system for 3 spectral bands and 2 linear polarization states is experimentally demonstrated. Furthermore, an optimal design is theoretically proposed, estimating that a system with a bandwidth of 127 nm and a spectral resolution of 1 nm is able to reconstruct the first three Stokes parameters with a signal-to-noise ratio of -13.14 dB with respect to the the shot noise limited SNR. The pixelated spectro-polarimetric system can be directly integrated on a sensor, thus enabling applicability in a variety of miniaturized optical devices, including but not limited to satellites for Earth observation.
RESUMO
A superoscillatory lens (SOL) is known to produce a sub-diffraction hotspot that is useful for high-resolution imaging. SOLs have not yet been directly used in a confocal reflection setup, as the SOL suffers from poor imaging properties. Additionally, the illuminating intensity distribution of the SOL still has high-intensity rings called sidelobes coexisting with the central hotspot. By means of a reflection setup, which does not have the SOL in the detection chain, thereby mitigating the poor imaging properties, we assessed the resolution capabilities of a SOL. This was done for different objects, whose dimensions were both above and below the SOL field-of-view (FOV). We found that the sidelobe illumination degrades the imaging properties in the case of extended objects, limiting the applicability of a SOL system.
RESUMO
In this paper, we present a design strategy for single layer metasurface lenses based on dielectric resonators. This strategy is based on a robust optimization procedure for the resonator distribution in order to meet required performances (e.g. encircled energy, bandwidth, field of view, etc.). Possible deviations due to manufacturing errors are taken into account in the design procedure. This is applied to the design of array of microlenses for maskless lithography applications. The final design shows more uniform focusing performances (bandwidth 20 nm at 395 nm - 415 nm, field of view ±60 mrad) and increased robustness against manufacturing errors, compared to designs based on analytic phase projections.
RESUMO
High-index dielectric metasurfaces featuring Mie-type electric and magnetic resonances have been of great interest in a variety of applications such as imaging, sensing, photovoltaics, and others, which led to the necessity of an efficient large-scale fabrication technique. To address this, here we demonstrate the use of single-pulse laser interference for direct patterning of an amorphous silicon film into an array of Mie resonators a few hundred nanometers in diameter. The proposed technique is based on laser-interference-induced dewetting. A precise control of the laser pulse energy enables the fabrication of ordered dielectric metasurfaces in areas spanning tens of micrometers and consisting of thousands of hemispherical nanoparticles with a single laser shot. The fabricated nanoparticles exhibit a wavelength-dependent optical response with a strong electric dipole signature. Variation of the predeposited silicon film thickness allows tailoring of the resonances in the targeted visible and infrared spectral ranges. Such direct and high-throughput fabrication is a step toward a simple realization of spatially invariant metasurface-based devices.