Slide electrification of drops at low velocities.

Slide electrification of drops is mostly investigated on tilted plate setups. Hence, the drop charging at low sliding velocity remains unclear. We overcome the limitations by developing an electro drop friction force instrument (eDoFFI). Using eDoFFI, we investigate slide electrification at the onset of drop sliding and at low sliding velocities ≤ 1 cm s-1. The novelty of eDoFFI is the simultaneous measurements of the drop discharging current and the friction force acting on the drop. The eDoFFI tool facilitates control on drop length and width using differently shaped rings. Hereby, slide electrification experiments with the defined drop length-to-width ratios >1 and <1 are realized. We find that width of the drop is the main geometrical parameter which determines drop discharging current and charge separation. We combine Kawasaki-Furmidge friction force equation with our finding on drop discharging current. This combination facilitates the direct measurement of surface charge density (σ) deposited behind the drop. We calculate σ ≈ 45 µC m-2 on Trichloro(1H,1H,2H,2H-perfluorooctyl)silane (PFOTS) and ≈20 µC m-2 on Trichloro(octyl)silane (OTS) coated glass surfaces. We find that the charge separation by moving drops is independent of sliding velocity ≤ 1 cm s-1. The reverse sliding of drop along the same scanline facilitates calculation of the surface neutralization time constant. The eDoFFI links two scientific communities: one which focuses on the friction forces and one which focuses on the slide electrification of drops.

Deep Learning to Analyze Sliding Drops.

State-of-the-art contact angle measurements usually involve image analysis of sessile drops. The drops are symmetric and images can be taken at high resolution. The analysis of videos of drops sliding down a tilted plate is hampered due to the low resolution of the cutout area where the drop is visible. The challenge is to analyze all video images automatically, while the drops are not symmetric anymore and contact angles change while sliding down the tilted plate. To increase the accuracy of contact angles, we present a 4-segment super-resolution optimized-fitting (4S-SROF) method. We developed a deep learning-based super-resolution model with an upscale ratio of 3; i.e., the trained model is able to enlarge drop images 9 times accurately (PSNR = 36.39). In addition, a systematic experiment using synthetic images was conducted to determine the best parameters for polynomial fitting of contact angles. Our method improved the accuracy by 21% for contact angles lower than 90° and by 33% for contact angles higher than 90°.

Fast-release kinetics of a pH-responsive polymer detected by dynamic contact angles.

Polymers conjugated with active agents have applications in biomedicine, anticorrosion, and smart agriculture. When the active agent is used as a drug, corrosion inhibitor, or pesticide, it can be released upon a specific stimulus. The efficiency and the sustainability of active agents are determined by the released kinetics. In this work, we study the fast-release kinetics of 8-hydroxyquinoline (8HQ) from a pH-responsive, random copolymer of methyl methacrylate and 8-quinolinyl-sulfide-ethyl acrylate [P(MMA-co-HQSEA)] by hydrolysis of the ß-thiopropionate groups. We used contact angle measurements of sliding drops as an elegant way to characterize the release kinetics. Based on the results gained from 1H nuclear magnetic resonance measurement, fluorescent intensity measurement, and velocity-dependent contact angle measurement, we found that both the hydrolysis rate and polymer conformation affect the release kinetics of 8HQ from a P(MMA-co-HQSEA) film. Polymer chains collapse and further suppress the release from the inner layer in acidic conditions, while polymer chains in a stretched condition further facilitate the release from the inner layer. As a result, the cumulative release rate of 8HQ is higher in the basic condition than in the acidic condition.

Scanning Drop Friction Force Microscopy.

Wetting imperfections are omnipresent on surfaces. They cause contact angle hysteresis and determine the wetting dynamics. Still, existing techniques (e.g., contact angle goniometry) are not sufficient to localize inhomogeneities and image wetting variations. We overcome these limitations through scanning drop friction force microscopy (sDoFFI). In sDoFFI, a 15 µL drop of Milli-Q water is raster-scanned over a surface. The friction force (lateral adhesion force) acting on the moving contact line is plotted against the drop position. Using sDoFFI, we obtained 2D wetting maps of the samples having sizes in the order of several square centimeters. We mapped areas with distinct wetting properties such as those present on a natural surface (e.g., a rose petal), a technically relevant superhydrophobic surface (e.g., Glaco paint), and an in-house prepared model of inhomogeneous surfaces featuring defined areas with low and high contact angle hysteresis. sDoFFI detects features that are smaller than 0.5 mm in size. Furthermore, we quantified the sliding behavior of drops across the boundary separating areas with different contact angles on the model sample. The sliding of a drop across this transition line follows a characteristic stick-slip motion. We use the variation in force signals, advancing and receding contact line velocities, and advancing and receding contact angles to identify zones of stick and slip. When scanning the drop from low to high contact angle hysteresis, the drop undergoes a stick-slip-stick-slip motion at the interline. Sliding from high to low contact angle hysteresis is characterized by the slip-stick-slip motion. The sDoFFI is a new tool for 2D characterization of wetting properties, which is applicable to laboratory-based samples but also characterizes biological and commercial surfaces.

Adaptation and Recovery of a Styrene-Acrylic Acid Copolymer Surface to Water.

Drops sliding down an adaptive surface lead to changes of the dynamic contact angles. Two adaptation processes play a role: 1) the adaptation of the surface upon bringing it into contact to the drop (wetting) and 2) the adaptation of the surface after the drop passed (dewetting). In order to study both processes, the authors investigate samples made from random styrene (PS)/acrylic acid (PAA) copolymers, which are exposed to water. Sum-frequency generation spectroscopy and tilted-plate measurements indicate that during wetting, the PS segments displace from the interface, while PAA segments are enriched. This structural adaptation of the PS/PAA random copolymer to water remains after dewetting. Annealing the adapted polymer induces reorientation of the PS segments to the surface.

Electronic effects of nano-confinement in functional organic and inorganic materials for optoelectronics.

When various optically and/or electronically active materials, such as conjugated polymers, perovskites, metals, and metal oxides, are confined at the nanoscale, they can exhibit unique nano-confined behavior that significantly differs from the behavior observed at the macroscale. Although controlled nano-confinement of functional materials can allow modulation of their electronic properties without the aid of any synthetic methodologies or additional chemical treatments, limited assembly approaches for nano-confinement and insufficient analytical tools for electronic characterization remain critical challenges in the development of novel optoelectronic materials and the investigation of their modulated properties. This review describes how the nano-confined features of organic and inorganic materials are related to the control and improvement of their optoelectronic properties. In particular, we focus on various assembly approaches for effective nano-confinement as well as methods for nano-electronic characterization. Then, we briefly present challenges and perspectives on the direction of nano-confinement in terms of the preparation of optoelectronic materials with desired functionalities. Furthermore, we believe that this review can provide a basis for developing and designing next-generation optoelectronics through nano-confinement.

Adaptation of a Styrene-Acrylic Acid Copolymer Surface to Water.

Solid surfaces, in particular polymer surfaces, are able to adapt upon contact with a liquid. Adaptation results in an increase in contact angle hysteresis and influences the mobility of sliding drops on surfaces. To study adaptation and its kinetics, we synthesized a random copolymer composed of styrene and 11-25 mol% acrylic acid (PS/PAA). We measured the dynamic advancing (θA) and receding (θR) contact angles of water drops sliding down a tilted plate coated with this polymer. We measured θA ≈ 87° for velocities of the contact line <20 µm/s. At higher velocities, θA gradually increased to ∼98°. This value is similar to θA of a pure polystyrene (PS) film, which we studied for comparison. We associate the gradual increase in θA to the adaptation process to water: The presence of water leads to swelling and/or an enrichment of acid groups at the water/polymer interface. By applying the latest adaptation theory (Butt et al. Langmuir 2018, 34, 11292), we estimated the time constant of this adaptation process to be ≪1 s. For sliding water drops, θR is ∼10° lower compared to the reference PS surface for all tested velocities. Thus, at the receding side of a sliding drop, the surface is already enriched by acid groups. For a water drop with a width of 5 mm, the increase in contact angle hysteresis corresponds to an increase in capillary force in the range of 45-60 µN, depending on sliding velocity.

Adaptive Wetting of Polydimethylsiloxane.

To better understand the wetting of cross-linked polydimethylsiloxane (PDMS), we measured advancing and receding contact angles of sessile water drops on cross-linked PDMS as a function of contact line velocity (up to 100 µm/s). Three types of samples were investigated: pristine PDMS, PDMS where oligomers were removed by toluene treatment, and PDMS with an enriched concentration of oligomers. Depending on the velocity of advancing contact lines and the contact time with water, different modes of wetting were observed: one with a relatively low contact angle hysteresis (Δθ ≈ 10°) and one with a larger hysteresis. We attribute the low hysteresis state, called the lubricated state, to the enrichment of free oligomers at the water-PDMS interface. The enrichment of oligomers is induced by drop contact. The kinetics of the transition to the lubricated state can be described by adaptation theory. PDMS adapts to the presence of water by an enrichment of free oligomers at the interface and a correlated reduction in interfacial tension.

Hygroscopic properties of NaCl nanoparticles on the surface: a scanning force microscopy study.

We investigated the hygroscopic growth of sodium chloride (NaCl) nanoparticles with curvature related diameters ranging from 10 nm to 200 nm, at different relative humidities using scanning force microscopy. Hygroscopic aerosol nanoparticles play a vital role in the Earth's climate and human health. We report that 10 nm NaCl nanoparticles adsorbed on silicon surfaces have a higher deliquescence relative humidity than larger NaCl nanoparticles (size > 30 nm). This finding is consistent with the observations for airborne nanoparticles by hygroscopicity tandem differential mobility analyzer. Therefore, the presence of silicon surfaces plays no significant role in the deliquescence relative humidity. Moreover, the study of individual airborne particles by means of scanning force microscopy revealed that the ability of water uptake, i.e. growth factor, of NaCl particles differs by as large as 40% at the same relative humidity. This finding indicates that the individual nature of NaCl particles influences the growth factor.

Two-Stage Collapse of PNIPAM Brushes: Viscoelastic Changes Revealed by an Interferometric Laser Technique.

Many temperature-responsive polymers exhibit a single-phase transition at the lower critical solution temperature (LCST). One exception is poly(N-isopropylacryamide) (PNIPAM). PNIPAM brush layers (51 ± 3 nm thick) that are end-grafted onto glass beads collapse in two stages. The viscoelastic changes of a PNIPAM brush layers were investigated with an interferometric laser method at different temperatures. This method is able to measure the two-stage collapse of beads coated with a polymer brush layer. When these beads are situated close to a hydrophilic glass surface, they exhibit Brownian motion. As this Brownian motion changes with temperature, the collapse of the polymer layer is revealed. The characteristic spectrum of the Brownian motion of beads is modeled by a damped harmonic oscillator, where the polymer layer acts as both spring and damping elements. The change of the Brownian motion spectrum with temperature indicates two transitions of the PNIPAM brush layer, one at 36 °C and one at 46 °C. We attribute the first transition to the LCST volume collapse of PNIPAM. Here, changes of the density and viscosity of the brush dominate. The second transition is dominated by a stiffening of the brush layer.

Calcium-Induced Molecular Rearrangement of Peptide Folds Enables Biomineralization of Vaterite Calcium Carbonate.

Proteins can control mineralization of CaCO3 by selectively triggering the growth of calcite, aragonite or vaterite phases. The templating of CaCO3 by proteins must occur predominantly at the protein/CaCO3 interface, yet molecular-level insights into the interface during active mineralization have been lacking. Here, we investigate the role of peptide folding and structural flexibility on the mineralization of CaCO3. We study two amphiphilic peptides based on glutamic acid and leucine with ß-sheet and α-helical structures. Though both sequences lead to vaterite structures, the ß-sheets yield free-standing vaterite nanosheet with superior stability and purity. Surface-spectroscopy and molecular dynamics simulations reveal that reciprocal structuring of calcium ions and peptides lead to the effective synthesis of vaterite by mimicry of the (001) crystal plane.

Adaptive Wetting-Adaptation in Wetting.

Many surfaces reversibly change their structure and interfacial energy upon being in contact with a liquid. Such surfaces adapt to a specific liquid. We propose the first order kinetic model to describe dynamic contact angles of such adaptive surfaces. The model is general and does not refer to a particular adaptation process. The aim of the proposed model is to provide a quantitative description of adaptive wetting and to link changes in contact angles to microscopic adaptation processes. By introducing exponentially relaxing interfacial energies and applying Young's equation locally, we predict a change of advancing and receding contact angles depending on the velocity of the contact line. Even for perfectly homogeneous and smooth surfaces, a dynamic contact angle hysteresis is obtained. As possible adaptations, we discuss changes and reconstruction of polymer surfaces or monolayers, diffusion and swelling, adsorption of surfactants, replacement of contaminants, reorientation of liquid molecules, or formation of an electric double layer.

Engineering Proteins at Interfaces: From Complementary Characterization to Material Surfaces with Designed Functions.

Once materials come into contact with a biological fluid containing proteins, proteins are generally-whether desired or not-attracted by the material's surface and adsorb onto it. The aim of this Review is to give an overview of the most commonly used characterization methods employed to gain a better understanding of the adsorption processes on either planar or curved surfaces. We continue to illustrate the benefit of combining different methods to different surface geometries of the material. The thus obtained insight ideally paves the way for engineering functional materials that interact with proteins in a predetermined manner.

Energy Dissipation of Moving Drops on Superhydrophobic and Superoleophobic Surfaces.

A water drop moving on a superhydrophobic surface or an oil drop moving on a superoleophobic surface dissipates energy by pinning/depinning at nano- and microprotrusions. Here, we calculate the work required to form, extend, and rupture capillary bridges between the protrusions and the drop. The energy dissipated at one protrusion WS is derived from the observable apparent receding contact angle Θrapp and the density of protrusions n by Ws = γ(cos Θrapp + 1)/n, where γ is the surface tension of the liquid. To derive an expression for Ws that links the microscopic structure of the surface to apparent contact angles, two models are considered: A superhydrophobic array of cylindrical micropillars and a superoleophobic array of stacks of microspheres. For a radius of a protrusion R and a receding materials contact angle Θr, we calculate the energy dissipated per protrusion as Ws = πγR2[A - ln(R/κ)]f(Θr). Here, A = 0.60 for cylindrical micropillars and 2.9 for stacks of spheres. κ is the capillary length. f(Θr) is a function which depends on Θr and the specific geometry, f ranges from ≈0.25 to 0.96. Combining both equations above, we can correlate the macroscopically observed apparent receding contact angle with the microscopic structure of the surface and its material properties.

Thermal Characterization of Dynamic Silicon Cantilever Array Sensors by Digital Holographic Microscopy.

In this paper, we apply a digital holographic microscope (DHM) in conjunction with stroboscopic acquisition synchronization. Here, the temperature-dependent decrease of the first resonance frequency (S1(T)) and Young's elastic modulus (E1(T)) of silicon micromechanical cantilever sensors (MCSs) are measured. To perform these measurements, the MCSs are uniformly heated from T0 = 298 K to T = 450 K while being externally actuated with a piezo-actuator in a certain frequency range close to their first resonance frequencies. At each temperature, the DHM records the time-sequence of the 3D topographies for the given frequency range. Such holographic data allow for the extracting of the out-of-plane vibrations at any relevant area of the MCSs. Next, the Bode and Nyquist diagrams are used to determine the resonant frequencies with a precision of 0.1 Hz. Our results show that the decrease of resonance frequency is a direct consequence of the reduction of the silicon elastic modulus upon heating. The measured temperature dependence of the Young's modulus is in very good accordance with the previously-reported values, validating the reliability and applicability of this method for micromechanical sensing applications.

Semifluorinated Alkanes at the Air-Water Interface: Tailoring Structure and Rheology at the Molecular Scale.

Semifluorinated alkanes form monolayers with interesting properties at the air-water interface due to their pronounced amphi-solvophobic nature and the stiffness of the fluorocarbons. In the present work, using a combination of structural and dynamic probes, we investigated how small molecular changes can be used to control the properties of such an interface, in particular its organization, rheology, and reversibility during compression-expansion cycles. Starting from a reference system perfluor(dodecyl)dodecane, we first retained the linear structure but changed the linkage groups between the alkyl chains and the fluorocarbons, by introducing either a phenyl group or two oxygens. Next, the molecular structure was changed from linear to branched, with four side chains (two fluorocarbons and two hydrocarbons) connected to extended aromatic cores. Neutron reflectivity at the air-water interface and scanning force microscopy on deposited films show how the changes in the molecular structure affect molecular arrangement relative to the interface. Rheological and compression-expansion measurements demonstrate the significant consequences of these changes in molecular structure and interactions on the interfacial properties. Remarkably, even with these simple molecules, a wide range of surface rheological behaviors can be engineered, from viscous over viscoelastic to brittle solids, for very similar values of the surface pressure.

Influence of the mixed organic cation ratio in lead iodide based perovskite on the performance of solar cells.

Lead halide based perovskite solar cells are presently the flagship among the third generation solution-processed photovoltaic technologies. The organic cation part in the perovskite plays an important role in terms of crystal structure tuning from tetragonal to trigonal or pseudocubic or vice versa depending on the organic cations used, while it also displays different microstructure. In this paper, we demonstrate the influence of the organic cation part with respect to optical properties, hysteresis behavior, and stability. This study offers a clear understanding of the perovskite properties and how they can be modulated by compositional engineering. With a rational choice, light harvesting abilities and hysteresis behavior can be controlled in these systems. The substitution of formamidinium cation by methylammonium cation allows achieving low temperature annealing and inducing stability in perovskites together with enhanced photovoltaic properties. By the use of in-situ scanning force microscopy experiments the conversion of precursors to perovskite at a particular temperature can be visualized.

Bottom-Up Fabrication of Nanopatterned Polymers on DNA Origami by In†Situ Atom-Transfer Radical Polymerization.

Bottom-up strategies to fabricate patterned polymers at the nanoscale represent an emerging field in the development of advanced nanodevices, such as biosensors, nanofluidics, and nanophotonics. DNA origami techniques provide access to distinct architectures of various sizes and shapes and present manifold opportunities for functionalization at the nanoscale with the highest precision. Herein, we conduct in situ atom-transfer radical polymerization (ATRP) on DNA origami, yielding differently nanopatterned polymers of various heights. After cross-linking, the grafted polymeric nanostructures can even stably exist in solution without the DNA origami template. This straightforward approach allows for the fabrication of patterned polymers with low nanometer resolution, which provides access to unique DNA-based functional hybrid materials.

Double Redox-Responsive Release of Encoded and Encapsulated Molecules from Patchy Nanocapsules.

Redox-responsive nanocapsules with surface regularities are presented. Two functional molecules are loaded in the nanocapsules. One molecule is chemically encoded in the capsule shell via a disulfide bond while the other one is physically entrapped in the capsule core. External reducing trigger can induce cascade release of the two payloads.

Photoswitching the mechanical properties in Langmuir layers of semifluorinated alkyl-azobenzenes at the air-water interface.

Semifluorinated alkyl-azobenzene derivatives (SFAB) can form stable Langmuir layers at the air-water interface. These systems combine the amphiphobic character of semifluorinated alkyl units as structure-directing motifs with photochromic behavior based on the well-known reversible cis-trans isomerization upon irradiation with UV and visible light. Herein, we report our investigations of the structural and dynamic tunability of these SFAB layers at the air-water interface in response to an external light stimulus. The monolayer structures and properties of [4-(heptadecafluorooctyl)phenyl](4-octylphenyl)diazene (F8-azo-H8) and bis(4-octylphenyl)diazene (H8-azo-H8) were studied by neutron reflectivity, surface pressure-area isotherms with compression-expansion cycles, and interfacial rheology. We find that UV irradiation reversibly influences the packing behavior of the azobenzene molecules and interpret this as a transition from organized layer structures with the main axis of the molecule vertically oriented in the trans form to random packing of the cis isomer. Interestingly, this trans-cis isomerization leads to an increase in surface pressure, which is accompanied by a decrease in viscoelastic moduli. These results suggest ways of tailoring the properties of responsive fluid interfaces.