Direct Measurement of the Surface Energy of Graphene.

Graphene produced by chemical vapor deposition (CVD) is a promising candidate for implementing graphene in a range of technologies. In most device configurations, one side of the graphene is supported by a solid substrate, wheras the other side is in contact with a medium of interest, such as a liquid or other two-dimensional material within a van der Waals stack. In such devices, graphene interacts on both faces via noncovalent interactions and therefore surface energies are key parameters for device fabrication and operation. In this work, we directly measured adhesive forces and surface energies of CVD-grown graphene in dry nitrogen, water, and sodium cholate using a modified surface force balance. For this, we fabricated large (∼1 cm2) and clean graphene-coated surfaces with smooth topography at both macro- and nanoscales. By bringing two such surfaces into contact and measuring the force required to separate them, we measured the surface energy of single-layer graphene in dry nitrogen to be 115 ± 4 mJ/m2, which was similar to that of few-layer graphene (119 ± 3 mJ/m2). In water and sodium cholate, we measured interfacial energies of 83 ± 7 and 29 ± 6 mJ/m2, respectively. Our work provides the first direct measurement of graphene surface energy and is expected to have an impact both on the development of graphene-based devices and contribute to the fundamental understanding of surface interactions.

A graphene surface force balance.

We report a method for transferring graphene, grown by chemical vapor deposition, which produces ultraflat graphene surfaces (root-mean-square roughness of 0.19 nm) free from polymer residues over macroscopic areas (>1 cm(2)). The critical step in preparing such surfaces involves the use of an intermediate mica template, which itself is atomically smooth. We demonstrate the compatibility of these model surfaces with the surface force balance, opening up the possibility of measuring normal and lateral forces, including friction and adhesion, between two graphene sheets either in contact or across a liquid medium. The conductivity of the graphene surfaces allows forces to be measured while controlling the surface potential. This new apparatus, the graphene surface force balance, is expected to be of importance to the future understanding of graphene in applications from lubrication to electrochemical energy storage systems.

Time dependent decomposition of ammonia borane for the controlled production of 2D hexagonal boron nitride.

Ammonia borane (AB) is among the most promising precursors for the large-scale synthesis of hexagonal boron nitride (h-BN) by chemical vapour deposition (CVD). Its non-toxic and non-flammable properties make AB particularly attractive for industry. AB decomposition under CVD conditions, however, is complex and hence has hindered tailored h-BN production and its exploitation. To overcome this challenge, we report in-depth decomposition studies of AB under industrially safe growth conditions. In situ mass spectrometry revealed a time and temperature-dependent release of a plethora of NxBy-containing species and, as a result, significant changes of the N:B ratio during h-BN synthesis. Such fluctuations strongly influence the formation and morphology of 2D h-BN. By means of in situ gas monitoring and regulating the precursor temperature over time we achieve uniform release of volatile chemical species over many hours for the first time, paving the way towards the controlled, industrially viable production of h-BN.

Publisher Correction: Time dependent decomposition of ammonia borane for the controlled production of 2D hexagonal boron nitride.

A correction to this article has been published and is linked from the HTML version of this paper. The error has been fixed in the paper.

Ultra-stiff large-area carpets of carbon nanotubes.

Herewith, we report the influence of post-synthesis heat treatment (≤2350 °C and plasma temperatures) on the crystal structure, defect density, purity, alignment and dispersibility of free-standing large-area (several cm(2)) carpets of ultra-long (several mm) vertically aligned multi-wall carbon nanotubes (VA-MWCNTs). VA-MWCNTs were produced in large quantities (20-30 g per batch) using a semi-scaled-up aerosol-assisted chemical vapour deposition (AACVD) setup. Electron and X-ray diffraction showed that the heat treatment at 2350 °C under inert atmosphere purifies, removes residual catalyst particles, and partially aligns adjacent single crystals (crystallites) in polycrystalline MWCNTs. The purification and improvement in the crystallites alignment within the MWCNTs resulted in reduced dispersibility of the VA-MWCNTs in liquid media. High-resolution microscopy revealed that the crystallinity is improved in scales of few tens of nanometres while the point defects remain largely unaffected. The heat treatment also had a marked benefit on the mechanical properties of the carpets. For the first time, we report compression moduli as high as 120 MPa for VA-MWCNT carpets, i.e. an order of magnitude higher than previously reported figures. The application of higher temperatures (arc-discharge plasma, ≥4000 °C) resulted in the formation of a novel graphite-matrix composite reinforced with CVD and arc-discharge-like carbon nanotubes.

Rapid epitaxy-free graphene synthesis on silicidated polycrystalline platinum.

Large-area synthesis of high-quality graphene by chemical vapour deposition on metallic substrates requires polishing or substrate grain enlargement followed by a lengthy growth period. Here we demonstrate a novel substrate processing method for facile synthesis of mm-sized, single-crystal graphene by coating polycrystalline platinum foils with a silicon-containing film. The film reacts with platinum on heating, resulting in the formation of a liquid platinum silicide layer that screens the platinum lattice and fills topographic defects. This reduces the dependence on the surface properties of the catalytic substrate, improving the crystallinity, uniformity and size of graphene domains. At elevated temperatures growth rates of more than an order of magnitude higher (120 µm min(-1)) than typically reported are achieved, allowing savings in costs for consumable materials, energy and time. This generic technique paves the way for using a whole new range of eutectic substrates for the large-area synthesis of 2D materials.

WS2 2D nanosheets in 3D nanoflowers.

In this work it has been established that 3D nanoflowers of WS2 synthesised by chemical vapour deposition are composed of few layer WS2 along the edges of the petals. An experimental study in order to understand the evolution of these nanostructures shows the nucleation and growth along with the compositional changes they undergo.

In situ engineering of NanoBud geometries.

NanoBuds exist in a variety of stable structures. Our studies show that engineering NanoBud geometries is indeed possible and we visualise the transformation of one Nanobud geometry to another using in situ aberration corrected imaging techniques. Such NanoBuds are precursors for generating nanotube junctions which could be used in composite and electronic applications.

Probing the bonding in nitrogen-doped graphene using electron energy loss spectroscopy.

Precise control of graphene properties is an essential step toward the realization of future graphene devices. Defects, such as individual nitrogen atoms, can strongly influence the electronic structure of graphene. Therefore, state-of-the-art characterization techniques, in conjunction with modern modeling tools, are necessary to identify these defects and fully understand the synthesized material. We have directly visualized individual substitutional nitrogen dopant atoms in graphene using scanning transmission electron microscopy and conducted complementary electron energy loss spectroscopy experiments and modeling which demonstrates the influence of the nitrogen atom on the carbon K-edge.