MOF Derivatives with Gradient Structure Anchored on Carbon Foam for High-Performance Electromagnetic Wave Absorption.

The impedance matching and high loss capabilities of composites with homogeneous distribution are limited owing to high addition and lack of structural design. Developing composites with heterogeneous distribution can achieve strong and wide electromagnetic (EM) wave absorption. However, challenges such as complex design and unclear absorption mechanisms still exist. Herein, a novel composite with a heterogeneous distribution gradient is successfully constructed via MOF derivatives Co@ nitrogen-doped carbon (Co@NC) anchored on carbon foam (CF) matrix (MDCF). Notably, the concentration of MOF can easily control the gradient structure. In particular, the morphologies of MOF derivatives on the surface of CF undergo a transition from the collapse of the inner layer to the integrity of the outer layer, accompanied by a continuous reduction in the size of Co nanoparticles. Correspondingly, enhanced interface polarization from the core-shell of Co@NC and good impedance matching of MDCF can be obtained. The optimized MDCF exhibits the minimum reflection loss of -68.18 dB at 2.01 mm and effective absorption bandwidth covering the entire X-band. Moreover, MDCF exhibits lightweight characteristics, excellent compressive strength, and low radar cross-section reduction. This work highlights the immense potential of composites with heterogeneous distribution for achieving high-performance EM wave absorption.

Development of Tablet Formulation of Amorphous Solid Dispersions Prepared by Hot Melt Extrusion Using Quality by Design Approach.

The objective of the study was to identify the extragranular component requirements (level and type of excipients) to develop an immediate release tablet of solid dispersions prepared by hot melt extrusion (HME) process using commonly used HME polymers. Solid dispersions of compound X were prepared using polyvinyl pyrrolidone co-vinyl acetate 64 (PVP VA64), Soluplus, and hypromellose acetate succinate (HPMCAS-LF) polymers in 1:2 ratio by HME through 18 mm extruder. A mixture design was employed to study effect of type of polymer, filler (microcrystalline cellulose (MCC), lactose, and dicalcium phosphate anhydrous (DCPA)), and disintegrant (Crospovidone, croscarmellose sodium, and sodium starch glycolate (SSG)) as well as level of extrudates, filler, and disintegrant on tablet properties such as disintegration time (DT), tensile strength (TS), compactibility, and dissolution. Higher extrudate level resulted in longer DT and lower TS so 60-70% was the maximum amount of acceptable extrudate level in tablets. Fast disintegration was achieved with HPMCAS-containing tablets, whereas Soluplus- and PVP VA64-containing tablets had higher TS. Crospovidone and croscarmellose sodium were more suitable disintegrant than SSG to achieve short DT, and MCC was a suitable filler to prepare tablets with acceptable TS for each studied HME polymer. The influence of extragranular components on dissolution from tablets should be carefully evaluated while finalizing tablet composition, as it varies for each HME polymer. The developed statistical models identified suitable level of fillers and disintegrants for each studied HME polymer to achieve tablets with rapid DT (<15 min) and acceptable TS (≥1 MPa at 10-15% tablet porosity), and their predictivity was confirmed by conducting internal and external validation studies.

Influence of processing parameters and formulation factors on the bioadhesive, temperature stability and drug release properties of hot-melt extruded films containing miconazole.

This study investigated the processing parameters and formulation factors on the bioadhesive properties, temperature stability properties, and drug release properties of miconazole in PolyOx® and Klucel® matrix systems produced by Hot-melt Extrusion (HME) technology. Miconazole incorporated into these matrix systems were found to be stable for 8 months by X-ray diffraction (XRD). The addition of miconazole increased area under the curve (AUC) at contact time intervals of 30 and 60 sec, while the bioadhesion decreased with an increase in processing temperatures. The release profiles suggest that a sustained release of miconazole was observed from all of the tested HME film formulations for approximately 10 h. The release from the optimal HME film extruded at 205°C was found to be significantly different than that extruded at 190°C. Therefore, this matrix system may address the present shortcomings of currently available therapy for oral and pharyngeal candidiasis.

Wearable Plasmonic Sensors Engineered via Active-Site Maximization of TiVC MXene for Universal Physiological Monitoring at the Molecular Level.

Two-dimensional transition metal carbon/nitrides (MXenes) are promising candidates to revolutionize next-generation wearable sensors as high-performance surface-enhanced Raman scattering (SERS) substrates. However, low sensitivity of pure MXene nanosheets and weak binding force or uncontrolled in situ growth of plasmonic nanoparticles on hybrid MXene composites limit their progress toward universal and reliable sensors. Herein, we designed and manufactured a highly sensitive, structurally stable wearable SERS sensor by in situ fabrication of plasmonic nanostructures on the flexible TiVC membranes via the maximization of chemically reducing sites using alkaline treatment. DFT calculations and experimental characterization demonstrated that the hydroxyl functional groups on the surface of MXenes can facilitate the reduction of metal precursors and the nucleation of gold nanoparticles (AuNPs) and can be covalently attached to AuNPs. Thus, the fabricated flexible TiVC-OH-Au sensor satisfied the rigorous mechanical requirements for wearable sensors. In addition, combining the electromagnetic (EM) enhancement from dense AuNPs formed by the activation of nucleation sites and charge transfer (CT) between target molecule and substrate induced by the abundant DOS near the Fermi level of TiVC, the fabricated sensor exhibits ultrasensitivity, long-term stability, good signal repeatability, and excellent mechanical durability. Moreover, the proof-of-concept application of the wearable SERS sensor in sweat sensing was demonstrated to monitor the content of nicotine, methotrexate, nikethamide, and 6-acetylmorphine in sweat at the molecular level, which was an important step toward the universality and practicality of the wearable sensing technology.

Stabilization of fenofibrate in low molecular weight hydroxypropylcellulose matrices produced by hot-melt extrusion.

The objective of this study was to improve the dissolution rate and to enhance the stability of a poorly water-soluble and low glass-trasition temperature (T(g)) model drug, fenofibrate, in low molecular weight grades of hydroxypropylcellulose matrices produced by hot-melt extrusion (HME). Percent drug loading had a significant effect on the extrudability of the formulations. Dissolution rate of fenofibrate from melt extruded pellets was faster than that of the pure drug (p < 0.05). Incorporation of sugars within the formulation further increased the fenofibrate release rates. Differential scanning calorimetry results revealed that the crystalline drug was converted into an amorphous form during the HME process. Fenofibrate is prone to recrystallization due to its low T(g). Various polymers were evaluated as stabilizing agents among which polyvinylpyrrolidone 17PF and amino methacrylate copolymer exhibited a significant inhibitory effect on fenofibrate recrystallization in the hot-melt extrudates. Subsequently immediate-release fenofibrate tablets were successfully developed and complete drug release was achieved within 5 min. The dissolution profile was comparable to that of a currently marketed formulation. The hot-melt extruded fenofibrate tablets were stable, and exhibited an unchanged drug release profile after 3-month storage at 40°C/75% RH.

Plasmonic Coupling of Au Nanoclusters on a Flexible MXene/Graphene Oxide Fiber for Ultrasensitive SERS Sensing.

High sensitivity, good signal repeatability, and facile fabrication of flexible surface enhanced Raman scattering (SERS) substrates are common pursuits of researchers for the detection of probe molecules in a complex environment. However, fragile adhesion between the noble-metal nanoparticles and substrate material, low selectivity, and complex fabrication process on a large scale limit SERS technology for wide-ranging applications. Herein, we propose a scalable and cost-effective strategy to a fabricate sensitive and mechanically stable flexible Ti3C2Tx MXene@graphene oxide/Au nanoclusters (MG/AuNCs) fiber SERS substrate from wet spinning and subsequent in situ reduction processes. The use of MG fiber provides good flexibility (114 MPa) and charge transfer enhancement (chemical mechanism, CM) for a SERS sensor and allows further in situ growth of AuNCs on its surface to build highly sensitive hot spots (electromagnetic mechanism, EM), promoting the durability and SERS performance of the substrate in complex environments. Therefore, the formed flexible MG/AuNCs-1 fiber exhibits a low detection limit of 1 × 10-11 M with a 2.01 × 109 enhancement factor (EFexp), signal repeatability (RSD = 9.80%), and time retention (remains 75% after 90 days of storage) for R6G molecules. Furthermore, the l-cysteine-modified MG/AuNCs-1 fiber realized the trace and selective detection of trinitrotoluene (TNT) molecules (0.1 µM) via Meisenheimer complex formation, even by sampling the TNT molecules at a fingerprint or sample bag. These findings fill the gap in the large-scale fabrication of high-performance 2D materials/precious-metal particle composite SERS substrates, with the expectation of pushing flexible SERS sensors toward wider applications.

Triple-enhanced Raman scattering sensors from flexible MXene/Au nanocubes platform via attenuating the coffee ring effect.

Developing substrates that combine sensitivity and signal stability is a major challenge in surface enhanced Raman scattering (SERS) research. Herein, we present a flexible triple-enhanced Raman Scattering MXene/Au nanocubes (AuNCs) sensor fabricated by selective filtration of Ti3C2Tx MXene/AuNCs hybrid on the Ti3C2Tx MXene membrane and subsequent treatment with 1H,1H,2H,2H-perfluoro-octyltriethoxysilane (FOTS). The resultant superhydrophobic MXene/AuNCs-FOTS membrane not only provides the SERS substrate with environmental stability, but also imparts analyte enrichment to enhance the sensitivity (LOD = 1 × 10-14 M) and reliability (RSD = 6.41%) for Rhodamine 6G (R6G) molecules owing to the attenuation of the coffee ring effect. Moreover, the triple enhancement mechanism of combining plasmonic coupling enhancement from plasmonic coupling (EM) of nearby AuNCs at lateral and longitudinal direction of MXene/AuNCs-FOTS membrane, charge transfer (CT) from Ti3C2Tx MXene and target molecules and analyte enrichment function provides the substrate with excellent SERS performance (EF = 3.19 × 109), and allows efficient quantification of biomarkers in urine. This work could provide new insights into MXenes as building blocks for high-performance substrates and fill existing gaps in SERS techniques.

High-efficient adsorption for versatile adsorbates by elastic reduced graphene oxide/Fe3O4 magnetic aerogels mediated by carbon nanotubes.

Fabrication of highly elastic three-dimensional aerogel adsorbents with outstanding adsorption capacities is a long pursuit for the treatment of industrial contaminated water. In this work, a magnetic reduced graphene oxide (rGO)/Fe3O4/carbon nanotubes (CNTs) aerogel material was constructed by the electrostatic attraction between the negatively charged GO and positively charged CNTs following a one-pot water bath treatment. The as-synthesized aerogel demonstrated high compressive stress (28.4 kPa) and lower density (24.11 mg/cm3) with exceptional adsorption capacities for versatile adsorbates which are attributed to CNTs and magnetic Fe3O4 nanoparticles. The effect of pH, initial concentration of adsorbates (dyes, Cd (ІІ) ions, organic solvents, and pump oil), content of CNTs and cyclic times on the adsorption capacities of the aerogel were investigated in detail. Furthermore, from simulation, the adsorption kinetics, and thermodynamics of the aerogel for adsorbates were more satisfied by endothermic quasi-second-order kinetic model with characteristic physical adsorption. Thus, the optimized rGO/Fe3O4/CNTs-10 aerogel adsorbent can be used as a powerful and versatile tool to deal with contaminated industrial or domestic wastewater.

Klucel™ EF and ELF polymers for immediate-release oral dosage forms prepared by melt extrusion technology.

The objective of this research work was to evaluate Klucel™ hydroxypropylcellulose (HPC) EF and ELF polymers, for solubility enhancement as well as to address some of the disadvantages associated with solid dispersions. Ketoprofen (KPR), a Biopharmaceutics Classification System class II drug with poor solubility, was utilized as a model compound. Preliminary thermal studies were performed to confirm formation of a solid solution/dispersion of KPR in HPC matrix and also to establish processing conditions for hot-melt extrusion. Extrudates pelletized and filled into capsules exhibited a carrier-dependent release with ELF polymer exhibiting a faster release. Tablets compressed from milled extrudates exhibited rapid release owing to the increased surface area of the milled extrudate. Addition of mannitol (MNT) further enhanced the release by forming micro-pores and increasing the porosity of the extrudates. An optimized tablet formulation constituting KPR, MNT, and ELF in a 1:1:1 ratio exhibited 90% release in 15 min similar to a commercial capsule formulation. HPC polymers are non-ionic hydrophilic polymers that undergo polymer-chain-length-dependent solubilization and can be used to enhance solubility or dissolution rate of poorly soluble drugs. Dissolution/release rate could be tailored for rapid-release applications by selecting a suitable HPC polymer and altering the final dosage form. The release obtained from pellets was carrier-dependent and not drug-dependent, and hence, such a system can be effectively utilized to address solubility or precipitation issues with poorly soluble drugs in the gastrointestinal environment.

Preparation and Adsorption Properties of Graphene-Modified, Pitch-Based Carbon Foam Composites.

In view of the good adsorption properties of graphene and carbon foam, they were combined to achieve the optimal matching of microstructures. Taking mesophase pitch as a raw material, pitch-based carbon foam was prepared by the self-foaming method. Graphene gel was prepared as the second phase to composite with the carbon foam matrix; graphene-modified, pitch-based carbon foam composites were finally obtained. Graphene gel was dispersed in the rich pore structure of carbon foam to improve its agglomeration and the porosity, and the active sites of the composite were further increased; the adsorption properties and mechanical properties of the composites were also significantly improved. The microstructure and morphology of the composites were studied by SEM, XRD and Raman spectroscopy; the compressive property and porosity were also tested. Methylene blue (MB) solution was used to simulate a dye solution for the adsorption test, and the influence of the composite properties and MB solution on the adsorption property was studied. Results showed that the compressive strength of the composite was 13.5 MPa, increased by 53.41%, and the porosity was 58.14%, increased by 24.15%, when compared to raw carbon foam. When the mass of the adsorbent was 150 mg, the initial concentration of the MB solution was 5 mg/L, and the pH value of the MB solution was 11; the graphene-modified carbon foam composites showed the best adsorption effect, with an adsorption rate of 96.3% and an adsorption capacity of 144.45 mg/g. Compared with the raw carbon foam, the adsorption rate and adsorption capacity of the composites were increased by 158.18% and 93.50%, respectively.

Controllable graphitization degree of carbon foam bulk toward electromagnetic wave attenuation loss behavior.

The graphitization degree is of great importance for determining the electromagnetic (EM) wave attenuation loss behavior. The conductive loss is considered to be the mechanism resulting from tailoring the graphitization degree. There is a lack of in-depth research on the dipole polarization caused by defects and functional groups and the interface polarization caused by graphite/amorphous carbon. Herein, lightweight carbon foam (CF) bulk derived from mesophase pitch was prepared to clarify the effect of the graphitization degree systematically. The results demonstrate that with an increase graphitization degree, the interfacial polarization improves and dipole polarization decreases. The synergistic effect of conduction loss and dipole and interfacial polarization dominates the impedance matching and further changes the EM loss behavior of CFs. Particularly, the minimum reflection loss is - 16.69 dB and effective absorption bandwidth is 3.63 GHz, the EM interference shielding effectiveness attains 35.13 dB and the compressive strength is up to 11.73 MPa when the optimal graphitization degree is achieved. Therefore, this work elucidates the effect of the interface polarization of graphite/amorphous carbon, thus providing a valuable insight into the design of advanced carbon-based materials for EM wave absorption and shielding.

Construction and Adsorption Performance Study of GO-CNT/Activated Carbon Composites for High Efficient Adsorption of Pollutants in Wastewater.

Based on the increasing application requirements for the efficient adsorption of wastewater pollutants, graphene oxide-carbon nanotube/activated carbon (GO-CNT/AC) composites are constructed from the optimal microstructure matching of GO, CNTs, and AC materials by solution impregnation and freeze-drying methods. Three-dimensional structures with nano-micro hierarchical pores are established, with GO and CNTs uniformly dispersed on the AC surface, effectively restrain the agglomeration. The added CNTs played a "spring" role, supporting the gap between the GO sheets and AC matrix. Meanwhile, stable links are formed between GO, CNTs, and AC, realizing the synergistic matching of the microstructure, which provides abundant active absorption sites beneficial for improving the adsorption performance. The influences of the CNT contents, adsorbent amounts, methylene blue (MB) concentrations, and pH values on the adsorption property of GO-CNT/AC composites are systematically investigated. The results show that when the pH value of the MB solution is 13, the CNT concentration is 3 mg/mL and the MB concentration is 200 mg/L, the adsorption property of the composite is the best, with an adsorption capacity of 190.8 mg/g and a removal percentage of 95.4%. Compared with the raw AC, the adsorption capacity and removal percentage of the composites are increased by 73.9% and 72.8%, respectively. The GO-CNT/AC composites exhibit excellent cyclic adsorption performance, with a cyclic stability of 91.8% after six rounds of adsorption-desorption cycles. The kinetic analysis shows that the adsorption process conforms to the PSO kinetic model. By fitting of the IPD model, the adsorption mechanisms of the GO-CNT/AC composites are divided into two adsorption stages and described respectively. This study provides a new way to achieve highly efficient adsorption of pollutants in wastewater.

Preparation and Adsorption Performance Study of Graphene Quantum Dots@ZIF-8 Composites for Highly Efficient Removal of Volatile Organic Compounds.

Based on the large specific surface area and excellent adsorption potential of graphene quantum dots (GQDs) and zeolitic imidazolate framework-8 (ZIF-8) materials, a GQDs@ZIF-8 composite was constructed to achieve optimal matching of the microstructure and to acquire efficient adsorption of volatile organic compounds (VOCs). GQDs and ZIF-8 were synthesized and then compounded by the solution co-deposition method to obtain GQDs@ZIF-8 composites. GQDs were uniformly decorated on the surface of the ZIF-8 metal-organic framework (MOF), effectively restraining the agglomeration, improving the thermal stability of ZIF-8 and forming abundant active sites. Thus, the VOC removal percentage and adsorption capacity of the GQDs@ZIF-8 composites were significantly improved. Toluene and ethyl acetate were chosen as simulated VOC pollutants to test the adsorption performance of the composites. The results showed that, after the addition of GQDs, the adsorption property of GQDs@ZIF-8 composites for toluene and ethyl acetate was obviously improved, with maximum adsorption capacities of 552.31 mg/g and 1408.59 mg/g, respectively, and maximum removal percentages of 80.25% and 93.78%, respectively, revealing extremely high adsorption performance. Compared with raw ZIF-8, the maximum adsorption capacities of the composites for toluene and ethyl acetate were increased by 53.82 mg/g and 104.56 mg/g, respectively. The kinetics and isotherm study revealed that the adsorption processes were in accordance with the pseudo-first-order kinetic model and the Freundlich isotherm model. The thermodynamic results indicated that the adsorption process of the GQDs@ZIF-8 composites was a spontaneous, endothermic and entropy increase process. This study provides a new way to explore MOF-based adsorption materials with high adsorption capacity which have broad application prospects in VOC removal fields.

Factors Affecting Consumers' Online Choice Intention: A Study Based on Bayesian Network.

In China, the mature development of online retail channels provides consumers with multiple consumption choices, and the factors that affect whether consumers choose to search or purchase online are numerous and complex. In this context, this paper reports on experimental research regarding consumers' willingness to choose channels based on the two-stage decision-making theory. Using structural equation modeling, the factors influencing consumers' online search intention and purchase willingness and the relationship between them are studied. In particular, the perceived benefits, channel trust, and channel transfer costs are explored. Furthermore, a Bayesian network is used in order to analyze the degree of influence of each factor quantitatively. It is found that online trust is an important factor affecting consumers' online search intention, and the most important factor for consumers' online purchase intention is their perceived benefits of online shopping. At the same time, there is a positive relationship between online search intention and purchase intention. This study can provide management decision support for online retail enterprises and help to promote the healthy development of online shopping.

Fabrication and Application of Black Phosphorene/Graphene Composite Material as a Flame Retardant.

A simple and novel route is developed for fabricating BP-based composite materials to improve the thermo-stability, flame retardant performances, and mechanical performances of polymers. Black phosphorene (BP) has outstanding flame retardant properties, however, it causes the mechanical degradation of waterborne polyurethane (WPU). In order to solve this problem, the graphene is introduced to fabricate the black phosphorene/graphene (BP/G) composite material by high-pressure nano-homogenizer machine (HNHM). The structure, thermo-stability, flame retardant properties, and mechanical performance of composites are analyzed by a series of tests. The structure characterization results show that the BP/G composite material can distribute uniformly into the WPU. The addition of BP/G significantly improves the residues of WPU in both of TG analysis (5.64%) and cone calorimeter (CC) test (12.50%), which indicate that the BP/G can effectively restrict the degradation of WPU under high temperature. The CC test indicates that BP/G/WPU has a lower peak release rate (PHRR) and total heat release (THR), which decrease by 48.18% and 38.63%, respectively, than that of the pure WPU, respectively. The mechanical analysis presents that the Young's modulus of the BP/G/WPU has an increase of seven times more than that of the BP/WPU, which indicates that the introduce of graphene can effectively improve the mechanical properties of BP/WPU.

In vitro and in vivo evaluation of tegaserod maleate pH-dependent tablets.

The purpose of this study was to prepare tegaserod maleate (TM) pH-dependent tablets and evaluate their advantages as a sustained release delivery system. TM, insoluble in water and unstable in gastric milieu, was formulated into pH-dependent tablets coated with combinations of two methacrylic acid copolymers - Eudragit L100 and Eudragit S100. The influence of core tablet compositions, polymer combination ratios and coating levels on the in vitro release rate of TM from coated tablets was investigated. The optimum formulation was evaluated for in vitro release rate and in vivo bioavailability study on beagle dogs. In addition, physico-chemical properties of the drug, including solubility at different pH and temperatures, and dissociation constant were determined. The results showed that no drug was released in 0.1 mol/L hydrochloric acid within 2h, and about 90% of the drug was released in the pH 6.8 phosphate buffer within 12h in a sustained manner. The pharmacokinetic investigation showed that TM pH-dependent tablets exhibited a sustained plasma concentration, a lag time of approximately 2.3h and a relative bioavailability of 159% compared to plain tablets. A close correlation existed between the in vitro release rate of the pH-dependent system and its in vivo absorption percentage. The results of the present study have demonstrated that the pH-dependent tablet system is a promising vehicle for preventing rapid hydrolysis in gastric milieu and improving oral bioavailability of TM for the treatment of irritable bowel syndrome.