Miniature holographic projector with cloud computing capability.

A fully functional miniaturized projection head below 5 cm3 is presented, using computer-generated holograms dynamically displayed on a liquid-crystal spatial light modulator. Spatial division of the modulator is used for color projection without color breakup, and specially designed, anti-reflection coated prisms ensure simple light paths with small losses. Real-time calculations are performed on a remote server with on-the-fly compression of holographic fringes. Cloud computing allows 1 W of local electrical power usage and apparent image brightness equivalent to 15-500 lm/W efficiency, depending on the displayed content. The properties of the projector allow future applications in handheld displays.

Collective matrix of spatial light modulators for increased resolution in holographic image projection.

We present a method to increase the resolution of holographically projected images by the use of a collective matrix of two phase-only spatial light modulators. As a result of fine alignment and common coherent illumination of the modulators, a synthetic aperture is formed with a doubled number of active pixels. In this paper we present theoretical analysis and numerical simulations which stand in good agreement for different distances between the apertures of modulators. We have achieved experimentally controlled field interference from both modulators on the projection screen, exhibiting increased resolution in one spatial direction and residual effects of the dead space between modulators. Then we have proved numerically possibility to extend our approach on bigger synthetic apertures consisted of more than two modulators.

Evaluation of the shadow effect in terahertz kinoform gratings.

The experimental and numerical evaluation of the shadow effect in kinoform diffractive gratings for the terahertz (THz) range is given. This effect limits the diffractive efficiency of dense gratings, which are the base of the elements suited for convenient beam focusing and imaging in THz. The observed effect of redirecting most of the incident energy into stray -1st diffractive order is observed and discussed. The presented results show the great significance of the shadow effect in selected kinoform gratings and prove the utility of the used methodology of numerical simulations.

Simple holographic projection in color.

Extremely simplified image projection technique based on optical fibers and a single Spatial Light Modulator is presented. Images are formed by addressing the modulator with especially iterated Fourier holograms, precisely aligned on the projection screen using phase factors of lenses and gratings. Focusing is done electronically with no moving parts. Color operation is done by spatial side-by-side division of the area of the modulator. Experimental results are given, showing good image quality and excellent resistance to obstructions in the light path. Speckles are suppressed by micro-movements of the screen and by time-averaging of a number of holograms into the final image.

Efficient image projection by Fourier electroholography.

An improved efficient projection of color images is presented. It uses a phase spatial light modulator with three iteratively optimized Fourier holograms displayed simultaneously--each for one primary color. This spatial division instead of time division provides stable images. A pixelated structure of the modulator and fluctuations of liquid crystal molecules cause a zeroth-order peak, eliminated by additional wavelength-dependent phase factors shifting it before the image plane, where it is blocked with a matched filter. Speckles are suppressed by time integration of variable speckle patterns generated by additional randomizations of an initial phase and minor changes of the signal.

Color image projection based on Fourier holograms.

A method of color image projection is experimentally validated. It assumes a simultaneous illumination of a spatial light modulator (SLM) with three laser beams converging in a common point on a projection screen. The beams are masked with amplitude filters so that each one illuminates one third of the area of the SLM. A Fourier hologram of a chosen color component of an input image is calculated, and its phase pattern is addressed on a corresponding part of the SLM area. A full-color flat image is formed on the screen as a result of color mixing. Additional techniques of image optimization are applied: time-integral speckle averaging and an off-axis shift of a zero-order peak. Static and animated experimental results of such a color holographic projection with a good image quality are presented.

Experimental evaluation of a full-color compact lensless holographic display.

An iterative phase retrieval method for a lensless color holographic display using a single light modulator is experimentally validated. The technique involves iterative calculation of a three-plane synthetic hologram which is displayed on a SLM simultaneously lit with three laser beams providing an RGB illumination. Static and animated two-dimensional flicker-free full color images are reconstructed at a fixed position and captured using a high resolution CMOS sensor. The image finesse, color fidelity, contrast ratio and influence of speckles are evaluated and compared with other techniques of holographic color image encoding. The results indicate the technique superior in a case of full-color real-life pictures which are correctly displayed by this ultra-compact and simple projection setup.

Assessment of imaging with extended depth-of-field by means of the light sword lens in terms of visual acuity scale.

We present outcomes of an imaging experiment using the refractive light sword lens (LSL) as a contact lens in an optical system that serves as a simplified model of the presbyopic eye. The results show that the LSL produces significant improvements in visual acuity of the simplified presbyopic eye model over a wide range of defocus. Therefore, this element can be an interesting alternative for the multifocal contact and intraocular lenses currently used in ophthalmology. The second part of the article discusses possible modifications of the LSL profile in order to render it more suitable for fabrication and ophthalmological applications.