Grain structure control during metal 3D printing by high-intensity ultrasound.

Additive manufacturing (AM) of metals, also known as metal 3D printing, typically leads to the formation of columnar grain structures along the build direction in most as-built metals and alloys. These long columnar grains can cause property anisotropy, which is usually detrimental to component qualification or targeted applications. Here, without changing alloy chemistry, we demonstrate an AM solidification-control solution to printing metallic alloys with an equiaxed grain structure and improved mechanical properties. Using the titanium alloy Ti-6Al-4V as a model alloy, we employ high-intensity ultrasound to achieve full transition from columnar grains to fine (~100 µm) equiaxed grains in AM Ti-6Al-4V samples by laser powder deposition. This results in a 12% improvement in both the yield stress and tensile strength compared with the conventional AM columnar Ti-6Al-4V. We further demonstrate the generality of our technique by achieving similar grain structure control results in the nickel-based superalloy Inconel 625, and expect that this method may be applicable to other metallic materials that exhibit columnar grain structures during AM.

Role of ultrasonic treatment, inoculation and solute in the grain refinement of commercial purity aluminium.

The present study investigates the influence of ultrasonic treatment on the grain refinement of commercial purity aluminium with a range of Al3Ti1B master alloy additions. When the aluminium contains the smallest amount of added master alloy, ultrasonics caused significant additional grain refinement compared to that provided by the master alloy alone. However, the influence of ultrasonics on grain size reduces with increasing addition of the master alloy which adds additional TiB2 particles and Ti solute with each incremental addition. Applying the Interdependence model to analyse the experimentally measured grain sizes revealed that the results of this study and those from similar experiments on an Al-2Cu alloy were consistent when the alloy compositions are converted to their growth restriction factors (Q) and that increasing Q had a major effect on reducing grain size and increasing grain number density. Compared with the application of ultrasonic treatment where an order of magnitude increase in the grain number density is achieved, an increase in the Ti content over the range of master alloy additions, causes the grain number density to increase by approximately three times.

Controlling initial biodegradation of magnesium by a biocompatible strontium phosphate conversion coating.

A simple strontium phosphate (SrP) conversion coating process was developed to protect magnesium (Mg) from the initial degradation post-implantation. The coating morphology, deposition rate and resultant phases are all dependent on the processing temperature, which determines the protective ability for Mg in minimum essential medium (MEM). Coatings produced at 80 °C are primarily made up of strontium apatite (SrAp) with a granular surface, a high degree of crystallinity and the highest protective ability, which arises from retarding anodic dissolution of Mg in MEM. Following 14 days' immersion in MEM, the SrAp coating maintained its integrity with only a small fraction of the surface corroded. The post-degradation effect of uncoated Mg and Mg coated at 40 and 80 °C on the proliferation and differentiation of human mesenchymal stem cells was also studied, revealing that the SrP coatings are biocompatible and permit proliferation to a level similar to that of pure Mg. The present study suggests that the SrP conversion coating is a promising option for controlling the early rapid degradation rate, and hence hydrogen gas evolution, of Mg implants without adverse effects on surrounding cells and tissues.

The complete amino acid sequence of human fibroblast interferon as deduced using synthetic oligodeoxyribonucleotide primers of reverse transcriptase.

Using synthetic oligodeoxyribonucleotides to prime the transcription of interferon mRNA and cDNA, we recently determined the mRNA sequence coding for the 47 amino-terminal amino acids of mature human fibroblast interferon (1). From this sequence, we have now synthesised an oligodeoxyribonucleotide that is homologous with the mRNA sequence coding for amino acids 42-45 and used it as a primer to selectively transcribe an interferon cDNA template. The sequence of the newly synthesised DNA predicted the sequence of amino acids 48-109 in the interferon polypeptide. By repeating this process with one more primer, we have determined the complete amino acid sequence of mature human fibroblast interferon, a polypeptide of 166 amino acids.