RESUMO
A brompheniramine taste-masked pediatric formulation was developed as part of the National Institutes of Health Pediatric Formulation Initiative to help address low patient compliance caused by the bitter taste of many adult formulations. To confirm that the taste-masked formulation can provide a similar pharmacological effect to the previous marketed adult formulations, a juvenile porcine model was used to screen the model pediatric formulation to compare the bioavailability between the marketed brompheniramine maleate and the taste-masked maleate/tannate formulation. Pigs were dosed orally with both formulations and blood samples were obtained from 0 to 48 h. Plasma samples were prepared and extracted using solid-phase extraction. The mass spectrometer was operated under selected ion monitoring mode. The selected ion monitoring channels were set to m/z 319.1 for brompheniramine and m/z 275.2 for the internal standard chlorpheniramine. Calibration curves were linear over the analytical range 0.2-20 ng/ml (r2 > 0.995) for brompheniramine in plasma. The intra- and inter-day accuracies were between 98.0 and 105% with 5.73% RSD precision. The bioanalytical method was successfully applied to a preclinical bioavailability study. The bioavailability profiles were not significantly different between the two formulations, which demonstrates that taste-masking with tannic acid is a promising approach for formulation modification for pediatric patients.
Assuntos
Disponibilidade Biológica , Bromofeniramina , Animais , Suínos , Bromofeniramina/farmacocinética , Bromofeniramina/química , Bromofeniramina/sangue , Reprodutibilidade dos Testes , Paladar , Modelos Lineares , Extração em Fase Sólida/métodosRESUMO
Winlevi® (clascoterone) topical cream (1%, w/w) was approved by the U.S. FDA for the treatment of acne vulgaris in patients 12 years of age and older. The active ingredient, clascoterone, is not stable in physiological solutions and can hydrolyze to cortexolone at body temperature. Instability of clascoterone poses a significant challenge in accurately assessing the rate and extent of clascoterone permeation in vitro. Therefore, the purpose of this study was to develop an in vitro skin permeation test (IVPT) method, and a robust analytical method, that can minimize hydrolyzation of clascoterone during the study for quantification of clascoterone. Two IVPT methods, using either vertical diffusion cells or flow-through cells, were developed and compared to evaluate in vitro permeation of clascoterone from Winlevi. A liquid chromatography with tandem mass spectrometry (LC-MS/MS) method was developed to monitor the level of clascoterone and cortexolone in the IVPT samples. The analytical method features a 2-min high-throughput analysis with good linearity, selectivity, and showed a lower limit of quantitation (LLOQ) of 0.5 ng/mL for both clascoterone and cortexolone. The in vitro skin permeation of clascoterone and cortexolone was observed as early as 2 h in both IVPT methods. A substantive amount of clascoterone was found to hydrolyze to cortexolone when using the vertical static diffusion cells with aliquot sampling. Conversely, degradation of clascoterone was significantly minimized when using the flow-through diffusion cells with fractional sampling. The data enhanced our understanding of in vitro permeation of clascoterone following topical application of the Winlevi topical cream, 1% and underscores the importance of IVPT method development and optimization during product development.
Assuntos
Cortodoxona , Absorção Cutânea , Creme para a Pele , Espectrometria de Massas em Tandem , Absorção Cutânea/efeitos dos fármacos , Absorção Cutânea/fisiologia , Creme para a Pele/farmacocinética , Creme para a Pele/administração & dosagem , Cortodoxona/administração & dosagem , Cortodoxona/farmacocinética , Cortodoxona/metabolismo , Cortodoxona/análogos & derivados , Espectrometria de Massas em Tandem/métodos , Pele/metabolismo , Administração Cutânea , Cromatografia Líquida/métodos , Animais , Permeabilidade , Suínos , Humanos , PropionatosRESUMO
An amino acid sequence variant (SV) is defined as an unintended amino acid substitution in protein drug products. SVs contribute to product heterogeneity and can potentially impact product quality, safety, immunogenicity, and efficacy. The analysis of biotherapeutics for SVs is important throughout the product life cycle including clone selection, development of nutrient feed strategies, commercial manufacturing process, and post-approval changes to monitor product quality. The proposed analytical procedure for SVs consists of both qualitative (identification of SVs) and quantitative (quantitation of identified SVs) components. The complexities of SV analysis and the variety of current procedures highlight the need for a systematic approach for assessing the capability of these methodologies to reliably identify and quantitate SVs in biotherapeutics. We described here a "spike-control" approach for evaluating SV analytical procedure. The concept was adopted from quality control samples routinely used in analytical procedure validation. One FDA approved monoclonal antibody (mAb) was spiked with accurate amounts of highly homologous mAb to create mAb samples containing low yet accurate levels of "artificial" SVs. Spike-control samples were denatured, reduced, alkylated, digested and then analyzed by high resolution Orbitrap mass spectrometry. In silico analysis revealed four single amino acid differences between the two mAbs that could be used to represent SVs in the spike-control samples. All four "artificial" SVs were reliably identified by the current workflow. Analytical range (0.01% to 2%), accuracy and precision of identified SVs have also been evaluated. Overall, spike-control sample(s) helped to demonstrate that the SV analytical procedure (i.e., sample preparation, LC separation, mass spectrometry determinations and bioinformatic software) was fit for purpose and suitable for the identification and quantitation of SVs at a pre-determined threshold.
Assuntos
Anticorpos Monoclonais , Software , Anticorpos Monoclonais/química , Sequência de Aminoácidos , Espectrometria de Massas/métodosRESUMO
RATIONALE: Systemic absorption of UV-filtering chemicals following topical application of sunscreens may present a safety concern. The Food and Drug Administration (FDA) had recommended an in vitro skin permeation test (IVPT) to evaluate the potential of this safety risk for the evaluation of sunscreens prior to clinical studies. Therefore, a sensitive and robust bioanalytical method(s) were required for IVPT studies of different topical sunscreen products. METHODS: An analytical procedure to quantitate sunscreen UV-filtering components and excipients in IVPT samples including avobenzone, octocrylene, oxybenzone, ecamsule, methylparaben and propylparaben was developed employing a RapidFire 360 robotic sample delivery system coupled with a triple quadrupole mass spectrometer. The analytical procedure was developed and validated according to the requirements of the FDA Bioanalytical Method Validation Guidance for Industry (2018). RESULTS: The analytical method provided a turnaround time of 12 seconds per sample and was determined to be accurate, precise, specific, and linear over the corresponding analytical ranges. The validated method was successfully applied for two IVPT studies for evaluating the skin permeation potential of UV-filtering chemicals and assisting with the selection of the sunscreen products for the clinical study conducted by the FDA. CONCLUSIONS: This work highlights the first analytical procedure that has applied a non-chromatographic-MS/MS automation platform to an in vitro biopharmaceutics study. The analytical platform simultaneously quantitated four UV filters and two excipients in complex media to evaluate their permeation in IVPT studies. The sample throughput and analytical performance of advanced automation platforms indicate their analytical procedure has the potential to significantly advance the efficiency of IVPT studies to evaluate permeation of a wide variety of UV chemical filters and excipients for topical OTC sunscreen products.
Assuntos
Absorção Cutânea , Protetores Solares , Automação , Excipientes , Humanos , Pele/química , Protetores Solares/análise , Espectrometria de Massas em Tandem/métodosRESUMO
The investigation of marketed hand wipe sanitizers presented an analytical challenge owing to the need for extraction from the solid matrix of the products. The present work describes the development of a new sample preparation method for the extraction of analytes from the hand wipe sanitizer matrix into dimethyl sulfoxide for analysis using headspace GCMS. Alcohol-based hand sanitizer (ABHS) wipe products labeled to contain ethanol or isopropanol as active ingredients were tested, varying in the size and weight of the wipes. The spike recovery assay was confirmed using spiking solutions containing impurities at concentrations equivalent to 50, 100 and 200% of the interim concentration limits. All of the tested analytes showed recovery within the allowable limits (80-120%). Six marketed ABHS wipe products were tested and no impurities above the FDA interim limits were observed. One product contained ethanol below the 60% v/v limit and another product was mislabeled for isopropanol and was found to contain ethanol instead. Four of the six ABHS products did not meet the label claim, which may affect the product quality. The analytical method and sample preparation procedures will provide the FDA and ABHS manufacturers with the capability to conduct quality assurance testing of hand wipe sanitizers for active ingredient content and impurities.
Assuntos
Higienizadores de Mão , 2-Propanol , Etanol , Cromatografia Gasosa-Espectrometria de MassasRESUMO
Evaluating the dermal absorption of sunscreen UV filters requires the development of a bio-predictable in vitro permeation test (IVPT). This work describes the comparison of two IVPT methods and rank order correlations of in vitro absorption (skin permeation and retention) with the in vivo absorption (AUC and skin retention) of sunscreens. The IVPT was compared regarding the following elements: (1) application of a single finite dose vs. an infinite dose and (2) the use of heat-separated human epidermis vs. dermatomed skin models. The IVPT was used to evaluate dermal absorption of six UV filters (avobenzone, homosalate, octinoxate, octisalate, octocrylene, and oxybenzone) in commercial sunscreens. Both the in vivo and in vitro permeation studies demonstrated that all UV filters were absorbed following a single-dose application. Sunscreens were rank ordered by the amount of the UV filters absorbed. Data obtained from the IVPT method using a single finite dose and heat-separated human epidermis was found to correlate with the clinical data. Rank orders of the cumulative in vitro skin permeation and the in vivo AUC were found comparable for oxybenzone, homosalate, octisalate, and octinoxate. Rank orders of the in vitro and in vivo skin retention of oxybenzone and octinoxate were also comparable. Additional IVPT parameters may be optimized to enhance the discriminatory power for UV filters with low skin permeation potential (e.g., avobenzone and octocrylene).
Assuntos
Absorção Cutânea , Protetores Solares , Temperatura Alta , Humanos , Técnicas In Vitro , Pele/metabolismo , Raios UltravioletaRESUMO
The variability of trace metals in cell culture media is a potential manufacturing concern because it may significantly affect the production and quality of therapeutic proteins. Variability in trace metals in CHO cell culture has been shown to impact critical production metrics such as cell growth, viability, nutrient consumption, and production of recombinant proteins. To better understand the influence of excess supplementation, zinc and copper were initially supplemented with 50-µM concentrations to determine the impact on the production and quality of ß-glucuronidase, a lysosomal enzyme, in a parallel bioreactor system. Ethylenediaminetetraacetic acid (EDTA), a metal chelator, was included as another treatment to induce a depletion of trace metal bioavailability to examine deficiency. Samples were drawn daily to monitor cell growth and viability, nutrient levels, ß-glucuronidase activity, and trace zinc flux. Cell cycle analysis revealed the inhibition of sub-G0/G1 species in zinc supplemented cultures, maintaining higher viability compared to the control, EDTA-, and copper-supplemented cultures. Enzyme activity analysis in the harvests revealed higher specific activity of ß-glucuronidase in reactors supplemented with zinc. A confirmation run was conducted with supplementations of zinc at concentrations of 50, 100, and 150 µM. Further cell cycle analysis and caspase-3 analysis demonstrated the role of zinc as an apoptosis suppressor responsible for the enhanced harvest purity of ß-glucuronidase from zinc-supplemented bioreactors.
Assuntos
Apoptose/efeitos dos fármacos , Meios de Cultura/química , Glucuronidase/biossíntese , Zinco/farmacologia , Animais , Técnicas de Cultura Celular por Lotes , Reatores Biológicos , Células CHO , Técnicas de Cultura de Células , Proliferação de Células/efeitos dos fármacos , Cobre/farmacologia , CricetulusRESUMO
A simple, sensitive and rapid ultra-high-performance liquid chromatography-electrospray ionization-tandem mass spectrometry method was developed and validated for the quantification of warfarin and 7-hydroxy warfarin in Sprague Dawley (SD) rats. Animals were administered a single dose of warfarin sodium formulations (crystalline and amorphous) at 12 mg/kg via oral gavage and blood was drawn over a 96-h time course. Sample process recoveries, matrix effect and analyte stability were determined. The linearity for warfarin and 7-hydroxy warfarin was from 5 to 2000 ng/mL in blank SD rat plasma. Correlation coefficients (r2 ) for standard calibration curves were >.98 and analytes quantified within ±15% of target at all calibrator concentrations. The average percent accuracy and precision for intra- and inter-day were 93.7%-113.8% and ≤12.1%, respectively, for warfarin and 7-hydroxy warfarin, across the quality control standards (5, 10, 500, 1800 and 2000 ng/mL). Acceptable analytical recovery (>55%) was achieved with process efficiencies >41.5% and matrix effects <139.9% over the analytical range. Both analytes were stable in stock solution, autosampler, benchtop and three cycles of freeze-thaw with percent accuracy ≥90.2% and precision (percent relative standard deviation) ≤14%. The validated method was successfully applied to a pre-clinical bioavailability study of crystalline and amorphous warfarin sodium formulations in SD rats.
Assuntos
Cromatografia Líquida de Alta Pressão/métodos , Espectrometria de Massas em Tandem/métodos , Varfarina/análogos & derivados , Administração Oral , Animais , Disponibilidade Biológica , Limite de Detecção , Modelos Lineares , Masculino , Ratos , Ratos Sprague-Dawley , Reprodutibilidade dos Testes , Varfarina/administração & dosagem , Varfarina/sangue , Varfarina/química , Varfarina/farmacocinéticaRESUMO
To evaluate the bioavailability and pharmacokinetic profiles of two novel galantamine formulations as medical countermeasure products, an ultra-performance liquid chromatography-single quadrupole mass spectrometry (UPLC-MS) method was developed and validated for quantifying galantamine in guinea pig plasma using solid-phase extraction with a mixed mode strong cation exchange reversed-phase cartridge. Chromatographic separation was achieved on a Waters Acquity UPLC BEH C18 column maintained at 40°C. The mobile phases were solution A, acetonitrile-water, 5:95 (v/v) and solution B, acetonitrile-water 90:10 (v/v), both containing 2 mM ammonium formate and 0.2% formic acid. The mobile phase was delivered utilizing a 3 min gradient program start with 95%A-5%B at a flow rate of 0.6 mL/min. The analyte and internal standard, galantamine-d3, were detected by selected ion monitoring mode on a Waters 3100 single quadrupole mass spectrometer with positive electrospray ionization. The method was validated according to the US Food and Drug Administration bioanalytical guidance. The method was selective and was linear over the analytical range of 2-2000 ng/mL. Accuracy and precision were acceptable with intra- and inter-day accuracies between 96.8 and 101% and precisions (RSD) <4.88%. The method was successfully implemented to measure galantamine plasma levels in a series of pre-clinical bioavailability studies for the evaluation of novel galantamine formulations.
RESUMO
With the finalization of the ICH Q14 Analytical Procedure Development guideline, how to apply enhanced approaches (such as analytical quality by design (AQbD)) to develop an analytical procedure, and to propose Established Conditions (ECs) and corresponding reporting categories, is increasingly being discussed. To gain practical experience in applying an enhanced approach for method development and identifying ECs, we developed, validated, and implemented an analytical procedure for a nitrosamine drug substance-related impurity (NDSRI). Here, as an example of the application of Q12 Lifecycle Management guideline principles in regards to analytical procedures, we briefly elaborate how: 1) the principles documented in the ICH Q14 guideline for analytical procedure development were applied, with the focus on identifying an Analytical Target Profile (ATP), knowledge management and risk assessment; 2) analytical procedure robustness according to the recommendations in ICH Q2(R2) Validation of Analytical Procedure guideline and Q14, were evaluated; and 3) mass spectrometry ECs and associated proposed reporting categories were proposed.
RESUMO
Reformulation with addition of antioxidants is one potential mitigation strategy to prevent or reduce nitrosamine drug substance-related impurities (NDSRIs) in drug products. To explore whether there could be other approaches to demonstrate bioequivalence for a reformulated oral product, which typically needs in vivo bioequivalence studies to support the changes after approval, the effects of antioxidant on the in vitro permeability of BCS III model drug substances were investigated to see whether there could be any potential impact on drug absorption. Six antioxidants were screened and four (ascorbic acid, cysteine, α-tocopherol and propyl gallate) were selected based on their nitrosamine inhibition efficiencies. The study demonstrated that these four antioxidants, at the tested amounts, did not have observable impact on the in vitro permeability of the BCS III model drug substances across Caco-2 cell monolayers in the In Vitro Dissolution Absorption System (IDAS). An in vitro permeability study could be considered as part of one potential bioequivalence bridging approach for reformulated low-risk immediate release solid oral products and oral suspension products. Other factors such as the influence of antioxidants on intestinal transporter activities should be considered where appropriate.
Assuntos
Antioxidantes , Permeabilidade , Humanos , Células CACO-2 , Antioxidantes/farmacologia , Antioxidantes/farmacocinética , Permeabilidade/efeitos dos fármacos , Absorção Intestinal/efeitos dos fármacos , Equivalência Terapêutica , Ácido Ascórbico/farmacologia , Preparações Farmacêuticas/metabolismo , Preparações Farmacêuticas/química , alfa-Tocoferol/farmacologia , Solubilidade , Cisteína/química , Administração OralRESUMO
We find that both Brevundimonas diminuta and Serratia marcescens can grow through sterilizing grade filter membranes of different membrane polymer compositions. Although this passage does not occur on a consistent basis, generation of "grow-through positive" results indicate that grow-through can occur stochastically at basal levels. This observation argues that the following risk mitigation strategies during pharmaceutical aseptic processing are warranted: minimization of processing times, and monitoring, minimizing and characterizing pre-filter bioburden.
Assuntos
Caulobacteraceae/crescimento & desenvolvimento , Filtração/instrumentação , Serratia marcescens/crescimento & desenvolvimento , Esterilização/instrumentaçãoRESUMO
To assay the dissolution samples of a drug product from several sources, a simple but broadly applicable analytical method is always desired. For the liquid-filled cyclosporine capsules, while analyzing the dissolution samples, the current compendial and literature HPLC methods have been found to be inadequate to provide satisfactory separation of the drug and the excipient peaks. Accordingly, a suitable isocratic reverse-phase HPLC method was developed for the analysis of dissolution samples of liquid-filled cyclosporine capsules. The method successfully separated the cyclosporine peak from the interfering chromatographic peaks of the excipients. The method was validated according to the ICH and FDA guidelines. Specificity, selectivity, linearity, accuracy, precision, and robustness were established over 3 days as part of method validation. Additionally, the degradation kinetics of cyclosporine in dissolution media was determined. Cyclosporine degradation followed a zero-order kinetics in the dissolution media with the respective rate constants of -3.5, -1.5, and -0.3%/h at 37°C, 25°C, and 10°C.
Assuntos
Cápsulas , Cromatografia Líquida de Alta Pressão/métodos , Ciclosporina/química , Cinética , Solubilidade , Espectrofotometria UltravioletaRESUMO
Starting in July 2018, the FDA alerted patients and health care professionals to the recall of ARBs such as valsartan by several pharmaceutical companies because of their potential contamination with carcinogenic nitrosamine impurities, including: (1) N-nitrosodimethylamine (NDMA), (2) N-nitrosodiethylamine (NDEA), (3) N-nitrosoethylisopropylamine (NEIPA), (4) N-nitrosodiisopropylamine (NDIPA), (5) N-nitrosodibutylamine (NDBA) and (6) N-nitroso-N-methyl-4-aminobutyric acid (NMBA). The FDA initiated a laboratory investigation to develop analytical procedures to test multiple lots of marketed ARB drugs to determine the possible presence of carcinogenic impurities and, if present, quantitate the levels of these impurities. Here the FDA laboratory developed and validated an automated micro-solid phase extraction MS/MS method, where all the analytes are not separated prior to elution to the MS, to simultaneously quantify NEIPA, NDIPA, NDBA and NMBA in ARB drug substances with an instrument sample analysis time of 12 seconds. The method was validated according to the ICH Q2(R1) guideline, and was determined to be specific, accurate, precise and linear over the corresponding nitrosamine analytical ranges. The method has been successfully implemented to quantitate the four nitrosamine impurities in 129 generic losartan, valsartan, olmesartan, irbesartan and telmisartan drug substance samples from 32 lots; and 32 losartan and valsartan drug product samples from 6 lots.
Assuntos
Losartan , Nitrosaminas , Humanos , Antagonistas de Receptores de Angiotensina , Espectrometria de Massas em Tandem/métodos , Inibidores da Enzima Conversora de Angiotensina , ValsartanaRESUMO
High molar mass polyethylene oxide (HM-PEO) is commonly used to enhance the mechanical strength of solid oral opioid drug products to deter abuse. Because the properties of PEO depend on molar mass distribution, accurately determining the molar mass distribution is a necessary part of understanding PEO's role in abuse-deterrent formulations (ADF). In this study, an asymmetrical flow field-flow fractionation (AF4) analytical procedure was developed to characterize PEO polymers with nominal molar masses of 1, 4 or 7 MDa as well as those from in-house prepared placebo ADF. The placebo ADF were manufactured using direct compress or hot-melt-extrusion methods, and subjected to physical manipulation, such as heating and grinding before measurement by AF4 were performed. The molar mass distribution characterized by AF4 revealed that PEO was sensitive to thermal stress, exhibiting decreased molar mass with increased heat exposure. The optimized AF4 method was deemed suitable for characterizing HM-PEO, offering adequate dynamic separation range for PEO with molar mass from 100 kDa to approximately 10 MDa.
Assuntos
Formulações de Dissuasão de Abuso , Fracionamento por Campo e Fluxo , Polietilenoglicóis , Fracionamento por Campo e Fluxo/métodos , Comprimidos , Composição de MedicamentosRESUMO
Nitrosamine compounds are classified as potential human carcinogens, the origin of these impurities can be broadly classified in two categories, nitrosamine impurity found in drug products that are not associated with the Active Pharmaceutical Ingredient (API), such as N-nitrosodimethylamine (NDMA) or nitrosamine impurities associated with the API, such as nitrosamine drug substance-related impurities (NDSRIs). The mechanistic pathway for the formation of these two classes of impurities can be different and the approach to mitigate the risk should be tailored to address the specific concern. In the last couple of years number of NDSRIs have been reported for different drug products. Though, not the only contributing factor for the formation of NDSIRs, it is widely accepted that the presence of residual a nitrites/nitrates in the components used in the manufacturing of the drug products can be the primary contributor to the formation of NDSRIs. Approaches to mitigate the formation of NDSRIs in drug products include the use of antioxidants or pH modifiers in the formulation. The primary objective of this work was to evaluate the role of different inhibitors (antioxidants) and pH modifiers in tablet formulations prepared in-house using bumetanide (BMT) as a model drug to mitigate the formation of N-nitrosobumetanide (NBMT). A multi-factor study design was created, and several bumetanide formulations were prepared by wet granulation with and without sodium nitrite spike (100 ppm) and different antioxidants (ascorbic acid, ferulic acid or caffeic acid) at three concentrations (0.1%, 0.5% or 1% of the total tablet weight). Formulations with acidic and basic pH were also prepared using 0.1 N hydrochloric acid and 0.1 N sodium bicarbonate, respectively. The formulations were subjected to different storage (temperature and humidity) conditions over 6 months and stability data was collected. The rank order of N-nitrosobumetanide inhibition was highest with alkaline pH formulations, followed by formulations with ascorbic acid, caffeic acid or ferulic acid present. In summary, we hypothesize that maintaining a basic pH or the addition of an antioxidant in the drug product can mitigate the conversion of nitrite to nitrosating agent and thus reduce the formation of bumetanide nitrosamines.
Assuntos
Bumetanida , Ácidos Cafeicos , Ácidos Cumáricos , Nitrosaminas , Humanos , Nitrosaminas/metabolismo , Antioxidantes/farmacologia , Ácido Ascórbico , Nitritos/metabolismo , ComprimidosRESUMO
The COVID-19 pandemic has led to increased usage of hand sanitizer products by the public to prevent the spread of COVID-19 and decrease the likelihood of acquiring the disease. The increase in demand has also led to an increase in the number of manufacturers. This work describes the FDA's Center for Drug Evaluation and Research (CDER) laboratories efforts to develop tests to assess the quality of hand sanitizer products containing ethanol or isopropanol as the primary active ingredient. The products were evaluated for the active ingredient content and determination of the 12 impurities listed in the FDA Hand Sanitizer Temporary Guidance, followed by a spike recovery assay performed to verify the test results. Extensive method development was conducted including an investigation into the stability of ethanol, isopropanol, and the 12 impurities. Stability and kinetic studies confirmed the instability of acetal in acidic liquid hand sanitizer products during spike recovery assay testing. The headspace GC-MS method was validated according to ICH Q2 (R1) guidelines and the spike recovery assay was validated using three concentrations of standards for the drug product. During method application, six liquid hand sanitizer products were tested and all were determined to have ethanol or isopropanol above 70% v/v. Two liquid hand sanitizer products were determined to contain acetaldehyde as an impurity above the FDA recommended safety levels. SUPPLEMENTARY INFORMATION: The online version contains supplementary material available at 10.1186/s41120-021-00049-8.
RESUMO
Aim: To develop and validate a fit for purpose method for the simultaneous determination of dexamethasone and its major metabolite, 6ß-hydroxydexamethasone, in rabbit plasma and ocular matrices to measure the in vivo release and distribution profile of dexamethasone from intravitreal implants. Materials & methods: An UHPLC-MS/MS system was employed to perform the bioanalysis. The method was validated according to the US FDA Bioanalytical Method Validation Guidance for Industry. Results & conclusion: The method was found to be fit-for-purpose for the described biological matrices and had a LLOQ of 0.1 ng/ml.
Assuntos
Humor Aquoso/química , Cromatografia Líquida de Alta Pressão/métodos , Dexametasona/análogos & derivados , Retina/química , Espectrometria de Massas em Tandem/métodos , Corpo Vítreo/química , Animais , Dexametasona/análise , Dexametasona/sangue , CoelhosRESUMO
The physical and chemical stability of therapeutic peptides presents challenges in developing robust formulations. The stability of the formulation affects product safety, efficacy and quality. Therefore, an understanding of the effects of formulation variables on the peptide's conformational structure and on its possible physical and chemical degradation is vital. To this end, computational and experimental analysis were employed to investigate the impact of formulation, peptide folding and product handling on oxidation, fibrillar aggregation and gelation of teriparatide. Teriparatide was used as a model drug due to the correlation of its conformation in solution with its pharmacological activity. Fibrillar aggregation and gelation were monitored using four orthogonal techniques. An innovative, automated platform coupled with ion mobility mass spectrometry was used for profiling chemical degradants. Increases in teriparatide concentration, pH, and ionic strength were found to increase the rate of fibrillar aggregation and gelation. Conversely, an increase in peptide folding and stabilization of the folded structures was found to decrease the rate of fibrillar aggregation and gelation. Moreover, the rate of oxidation was found to be inversely related to its solution concentration and extent of peptide folding. The present study provides an insight into formulation strategies designed to reduce the potential risk of physical and chemical degradation of peptides with a defined conformation.
Assuntos
Peptídeos , Conformação Molecular , Concentração Osmolar , OxirreduçãoRESUMO
The 14th edition of the Workshop on Recent Issues in Bioanalysis (14th WRIB) was held virtually on June 15-29, 2020 with an attendance of over 1000 representatives from pharmaceutical/biopharmaceutical companies, biotechnology companies, contract research organizations, and regulatory agencies worldwide. The 14th WRIB included three Main Workshops, seven Specialized Workshops that together spanned 11 days in order to allow exhaustive and thorough coverage of all major issues in bioanalysis, biomarkers, immunogenicity, gene therapy, cell therapy and vaccine. Moreover, a comprehensive vaccine assays track; an enhanced cytometry track and updated Industry/Regulators consensus on BMV of biotherapeutics by Mass Spectrometry (hybrid assays, LCMS and HRMS) were special features in 2020. As in previous years, this year's WRIB continued to gather a wide diversity of international industry opinion leaders and regulatory authority experts working on both small and large molecules to facilitate sharing and discussions focused on improving quality, increasing regulatory compliance and achieving scientific excellence on bioanalytical issues. This 2020 White Paper encompasses recommendations emerging from the extensive discussions held during the workshop and is aimed to provide the Global Bioanalytical Community with key information and practical solutions on topics and issues addressed, in an effort to enable advances in scientific excellence, improved quality and better regulatory compliance. Due to its length, the 2020 edition of this comprehensive White Paper has been divided into three parts for editorial reasons. This publication covers the recommendations on (Part 1) Hybrid Assays, Innovation in Small Molecules, & Regulated Bioanalysis. Part 2A (BAV, PK LBA, Flow Cytometry Validation and Cytometry Innovation), Part 2B (Regulatory Input) and Part 3 (Vaccine, Gene/Cell Therapy, NAb Harmonization and Immunogenicity) are published in volume 13 of Bioanalysis, issues 5, and 6 (2021), respectively.