RESUMO
Lignocellulosic biomass offers a renewable carbon source which can be anaerobically digested to produce short-chain carboxylic acids. Here, we assess fuel properties of oxygenates accessible from catalytic upgrading of these acids a priori for their potential to serve as diesel bioblendstocks. Ethers derived from C2 and C4 carboxylic acids are identified as advantaged fuel candidates with significantly improved ignition quality (>56% cetane number increase) and reduced sooting (>86% yield sooting index reduction) when compared to commercial petrodiesel. The prescreening process informed conversion pathway selection toward a C11 branched ether, 4-butoxyheptane, which showed promise for fuel performance and health- and safety-related attributes. A continuous, solvent-free production process was then developed using metal oxide acidic catalysts to provide improved thermal stability, water tolerance, and yields. Liter-scale production of 4-butoxyheptane enabled fuel property testing to confirm predicted fuel properties, while incorporation into petrodiesel at 20 vol % demonstrated 10% improvement in ignition quality and 20% reduction in intrinsic sooting tendency. Storage stability of the pure bioblendstock and 20 vol % blend was confirmed with a common fuel antioxidant, as was compatibility with elastomeric components within existing engine and fueling infrastructure. Technoeconomic analysis of the conversion process identified major cost drivers to guide further research and development. Life-cycle analysis determined the potential to reduce greenhouse gas emissions by 50 to 271% relative to petrodiesel, depending on treatment of coproducts.
RESUMO
While today's biomass-based diesel fuels are used at relatively low blend levels in petroleum diesel, decarbonization of the heavy-duty trucking and off-road sectors is driving increasing use of higher level blends and the combination of hydroprocessing-derived renewable diesel (RD) with biodiesel (fatty acid methyl esters) to create a 100% renewable fuel. However, little data are available on the properties of biodiesel blends over 20 vol % into RD or conventional diesel, despite the potential for properties to fall well outside the normal range for diesel fuels. Here, we evaluate the properties of 20-80% blends of a soy-derived biodiesel into RD and petroleum diesel. Properties measured were flash point, cloud point, cetane number, surface tension, density, kinematic viscosity, distillation curve, lower heating value, water content, water solubility in the fuel, lubricity, and oxidation stability. Density and viscosity were measured over a wide temperature range. A key objective was to reveal properties that might limit blending of biodiesel and any differences between biodiesel blends into RD versus petroleum diesel and to understand research needed to advance the use of high-level blends and 100% renewable fuel. Properties that may limit blending include the cloud point, viscosity, distillation curve, and oxidation stability. Meeting cloud point requirements can be an issue for all distillate fuels. For biodiesel, reducing the blend level and use of lower cloud point hydrocarbon blendstocks, such as No. 1 diesel or kerosene, can be used in winter months. Alternatively, a heated fuel system that allows for starting the vehicle on conventional diesel before switching to pure biodiesel (B100) or a high-level blend has been successfully demonstrated in the literature. Some biodiesels can have kinematic viscosity above the upper limit for diesel fuels (4.1 mm2/s), which will limit the amount that can be blended. Biodiesel boils in a narrow range at the very high end of the No. 2 diesel range. Additional research is needed to understand how the high T90 of B100 and high-level blends and the very low distillation range of B100, some RD samples, and high-level biodiesel blends impact lube oil dilution, engine deposits, and diesel oxidation catalyst light-off. Blending with No. 1 diesel or kerosene or biodiesel-specific engine calibrations may mitigate these issues. Oxidation stability of higher level blends is poorly understood but may be addressed through the increased use of antioxidant additives. Finally, high-level biodiesel blends and B100 will have significantly higher density, viscosity, and surface tension compared to conventional diesel. In combination with the high boiling point, these properties may impact fuel spray atomization and evaporation, and additional research is needed in this area.
RESUMO
The hazards to health and the environment associated with the transportation sector include smog, particulate matter, and greenhouse gas emissions. Conversion of lignocellulosic biomass into biofuels has the potential to provide significant amounts of infrastructure-compatible liquid transportation fuels that reduce those hazardous materials. However, the development of these technologies is inefficient, due to: (i) the lack of a priori fuel property consideration, (ii) poor shared vocabulary between process chemists and fuel engineers, and (iii) modern and future engines operating outside the range of traditional autoignition metrics such as octane or cetane numbers. In this perspective, we describe an approach where we follow a "fuel-property first" design methodology with a sequence of (i) identifying the desirable fuel properties for modern engines, (ii) defining molecules capable of delivering those properties, and (iii) designing catalysts and processes that can produce those molecules from a candidate feedstock in a specific conversion process. Computational techniques need to be leveraged to minimize expenses and experimental efforts on low-promise options. This concept is illustrated with current research information available for biomass conversion to fuels via catalytic fast pyrolysis and hydrotreating; outstanding challenges and research tools necessary for a successful outcome are presented.
Assuntos
Biocombustíveis , Pirólise , Biomassa , Catálise , Material ParticuladoRESUMO
[reaction: see text] Haloacetal radical cyclizations of alpha- and beta-hydroxyhydrazones provide a direct access to aminosugarlike compounds. Stereocontrol of this process is influenced by stereogenic centers of both the hydroxyhydrazone and the acetal. The outcomes are consistent with chair and twist transition states with the anomeric alkoxy group in pseudoaxial orientations.