ID22 - the high-resolution powder-diffraction beamline at ESRF.

Following Phase 2 of the upgrade of the ESRF in which the storage ring was replaced by a new low-emittance ring along with many other facility upgrades, the status of ID22, the high-resolution powder-diffraction beamline, is described. The beamline has an in-vacuum undulator as source providing X-rays in the range 6-75 keV. ID22's principle characteristics include very high angular resolution as a result of the highly collimated and monochromatic beam, coupled with a 13-channel Si 111 multi-analyser stage between the sample and a Dectris Eiger2 X 2M-W CdTe pixel detector. The detector's axial resolution allows recorded 2θ values to be automatically corrected for the effects of axial divergence, resulting in narrower and more-symmetric peaks compared with the previous fixed-axial-slit arrangement. The axial acceptance can also be increased with increasing diffraction angle, thus simultaneously improving the statistical quality of high-angle data. A complementary Perkin Elmer XRD1611 medical-imaging detector is available for faster, lower-resolution data, often used at photon energies of 60-70 keV for pair-distribution function analysis, although this is also possible in high-resolution mode by scanning up to 120°â€…2θ at 35 keV. There are various sample environments, allowing sample temperatures from 4 K to 1600°C, a capillary cell for non-corrosive gas atmospheres in the range 0-100 bar, and a sample-changing robot that can accommodate 75 capillary samples compatible with the temperature range 80 K to 950°C.

EIGER2 hybrid-photon-counting X-ray detectors for advanced synchrotron diffraction experiments.

The ability to utilize a hybrid-photon-counting detector to its full potential can significantly influence data quality, data collection speed, as well as development of elaborate data acquisition schemes. This paper facilitates the optimal use of EIGER2 detectors by providing theory and practical advice on (i) the relation between detector design, technical specifications and operating modes, (ii) the use of corrections and calibrations, and (iii) new acquisition features: a double-gating mode, 8-bit readout mode for increasing temporal resolution, and lines region-of-interest readout mode for frame rates up to 98 kHz. Examples of the implementation and application of EIGER2 at several synchrotron sources (ESRF, PETRA III/DESY, ELETTRA, AS/ANSTO) are presented: high accuracy of high-throughput data in serial crystallography using hard X-rays; suppressing higher harmonics of undulator radiation, improving peak shapes, increasing data collection speed in powder X-ray diffraction; faster ptychography scans; and cleaner and faster pump-and-probe experiments.

3D Anionic Silicate Covalent Organic Framework with srs Topology.

The synthesis of 3D covalent organic frameworks (COFs) adopting novel topologies is challenging, and so far 3D COFs have only been reported for nets based on building blocks with tetrahedral geometry. We demonstrate the targeted synthesis of an anionic 3D COF crystallizing in a three-coordinated srs net by exploiting a recently developed linkage for the formation of anionic silicate COFs based on hypercoordinate silicon nodes. The framework, named SiCOF-5, was synthesized by reticulating dianionic hexacoordinate [SiO6]2- nodes with triangular triphenylene building blocks and adopts a two-fold interpenetrated srs-c net with an overall composition of Na2[Si(C18H6O6)] (where C18H6O6 is triphenylene-2,3,6,7,10,11-hexakis(olate)). A key requirement for the crystallization of SiCOF-5 was the careful control over the nucleation and growth rate by gradual generation of the silicon source during the course of the reaction.

Observation of Binding and Rotation of Methane and Hydrogen within a Functional Metal-Organic Framework.

The key requirement for a portable store of natural gas is to maximize the amount of gas within the smallest possible space. The packing of methane (CH4) in a given storage medium at the highest possible density is, therefore, a highly desirable but challenging target. We report a microporous hydroxyl-decorated material, MFM-300(In) (MFM = Manchester Framework Material, replacing the NOTT designation), which displays a high volumetric uptake of 202 v/v at 298 K and 35 bar for CH4 and 488 v/v at 77 K and 20 bar for H2. Direct observation and quantification of the location, binding, and rotational modes of adsorbed CH4 and H2 molecules within this host have been achieved, using neutron diffraction and inelastic neutron scattering experiments, coupled with density functional theory (DFT) modeling. These complementary techniques reveal a very efficient packing of H2 and CH4 molecules within MFM-300(In), reminiscent of the condensed gas in pure component crystalline solids. We also report here, for the first time, the experimental observation of a direct binding interaction between adsorbed CH4 molecules and the hydroxyl groups within the pore of a material. This is different from the arrangement found in CH4/water clathrates, the CH4 store of nature.

Metal Vacancy Ordering in an Antiperovskite Resulting in Two Modifications of Fe2 SeO.

Small, red Fe2 SeO single crystals in two modifications were obtained from a CsCl flux. The metastable α-phase is pseudo-tetragonal (Cmce, a=16.4492(8) Å, b=11.1392(4) Å, c=11.1392(4) Å), whereas the ß-phase is trigonal (P31 , a=9.8349(4) Å, c=6.9591(4) Å)) and thermodynamically stable within a narrow temperature range. Both crystal structures were solved from twinned specimens. The enantiomers of the ß-phase appear as racemic mixtures. Selenium and oxygen form two individual interpenetrating primitive cubic lattices, giving a bcc packing. A quasi-octahedrally coordinated iron atom is found close to the center of each surface of the selenium sublattice. The difference between the α- and ß-phases is the distribution of iron at 2/3 of the surfaces. α- and ß-Fe2 SeO are comparable with metal-vacancy-ordered antiperovskites. Each Fe/O lattice can also be described in terms of vertex-sharing OFe4 tetrahedra, with a crystal structure similar to that of an antisilicate. Iron is divalent and has a high-spin d(6) (S=2) configuration. The ß-phase exhibits magnetoelectric coupling.

Silver Indium Telluride Semiconductors and Their Solid Solutions with Cadmium Indium Telluride: Structure and Physical Properties.

Ag0.8In2.4Te4 (= AgIn3Te5) and Ag0.5In2.5Te4 (= AgIn5Te8) form solid solutions with CdIn2Te4, which are interesting as materials for photovoltaics or with respect to their thermoelectric properties. The corresponding crystal structures are related to the chalcopyrite type. Rietveld refinements of high-resolution synchrotron powder diffraction data measured at K-absorption edges of Cd, Ag, In, and Te and electron diffraction reveal the symmetry as well as the element and vacancy distribution in Ag0.8In2.4Te4 (= AgIn3Te5)/Ag0.5In2.5Te4 (= AgIn5Te8) mixed crystals such as Ag0.25Cd0.5In2.25Te4 and Ag0.2Cd0.75In2.1Te4. All compounds of the solid solution series (CdIn2Te4)x(Ag0.5In2.5Te4)1-x exhibit the HgCu2I4 structure type (space group I4̅2m) with completely ordered vacancies but disordered cations. The uniform cation distribution and thus the local charge balance are comparable to that of CdIn2Te4. In contrast, Ag0.8In2.4Te4 (= AgIn3Te5) crystallizes in the space group P4̅2c with disordered cations and partially ordered vacancies. This is corroborated by bond-valence sum calculations and the fact that there is a Vegard-like behavior for compounds with 0.5 < x in the pseudobinary system (CdIn2Te4)x(Ag0.8In2.4Te4)1-x. Owing to the different structures, there is no complete solid solution series between CdIn2Te4 and AgIn3Te5. All compounds in this work are n-type semiconductors with a low electrical conductivity (∼1 S/m) and rather high absolute Seebeck coefficients (up to -750 µV/mK; 225 °C). Electrical band gaps (Eg) determined from the Seebeck coefficients as well as (more reliably) from the electrical conductivity range between 0.19 and 1.13 eV.

Synthesis, dopant solubility, and thermostructural properties of Ca10.5-xTMx(VO4)7 (TM = Co, Cu) as function of transition metal content.

Crystals of Ca10.5-xTMx(VO4)7 (TM = Co, Cu), belonging to the whitlockite family, were synthesized by solid-state reaction and studied as a function of the TM content (x) for the first time. The structure was refined at ambient conditions and at high temperatures up to 1200 K using the Rietveld method. The unit cell size significantly decreases with increasing TM content up to the solubility limit, xlim, which is 0.78(3) for TM = Co and 0.75(4) for TM = Cu. Occupancy factors show a preference for the M5 site by Co/Cu. The unit cell size varies smoothly with temperature, while the axial ratio exhibits nonlinear behaviour above approximately 800 K. The thermal expansion coefficient was determined from 300-1100 K. Atomic arrangement modifications at higher temperatures are indicated by changes in the axial ratio, the thermal expansion coefficient, and the reduction of fractional TM occupancy at the M5 site at specific temperatures.

Nanosheets of a Layered Metal-Organic Framework for Separation of CO2/CH4 using Mixed Matrix Membranes.

Mixed matrix membranes represent an important technology for gas separations. Nanosheets of metal-organic framework (MOF) materials of high aspect ratio and size-selective gas transport properties have the potential to promote the efficient mixing of components to form membranes for gas separation. Herein, we report a bottom-up synthesis of extended sheets of kagomé (kgm) topology, kgmt-Bu, via the linkage of [Cu2(O2CR)4] paddlewheels with 5-tert-butylisophthalic acid. The growth of the layered structure can be controlled by the choice of solvent and modulator. Nanosheets of kgmt-Bu of average thickness of 20 nm and aspect ratio of 40 to 50 can be obtained, and the sieving effect of the channels in kgmt-Bu boost the efficient separation of CO2 over CH4. A mixed matrix membrane comprising kgmt-Bu nanosheets with Matrimid shows a 32% enhancement in CO2/CH4 selectivity compared with the membrane incorporating the MOF in the particulate form.

Revisiting Solid-Solid Phase Transitions in Sodium and Potassium Tetrafluoroborate for Thermal Energy Storage.

In situ synchrotron powder X-ray diffraction (PXRD) study was conducted on sodium and potassium tetrafluoroborate (NaBF4 and KBF4) to elucidate structural changes across solid-solid phase transitions over multiple heating-cooling cycles. The phase transition temperatures from diffraction measurements are consistent with the differential scanning calorimetry data (∼240 °C for NaBF4 and ∼290 °C for KBF4). The crystal structure of the high-temperature (HT) NaBF4 phase was determined from synchrotron PXRD data. The HT disordered phase of NaBF4 crystallizes in the hexagonal, space group P63/mmc (no. 194) with a = 4.98936(2) Å, c = 7.73464(4) Å, V = 166.748(2) Å3, and Z = 2 at 250 °C. Density functional theory molecular dynamics (MD) calculations imply that the P63/mmc is indeed a stable structure for rotational NaBF4. MD simulations reproduce the experimental phase sequence upon heating and indicate that F atoms are markedly more mobile than K and B atoms in the disordered state. Thermal expansion coefficients for both phases were determined from high-precision lattice parameters at elevated temperatures, as obtained from Rietveld refinement of the PXRD data. Interestingly, for the HT-phase of NaBF4, the structure (upon heating) contracts slightly in the a-b plane but expands in the c direction such that overall thermal expansion is positive. Thermal conductivities at room temperature were measured, and the values are 0.8-1.0 W m-1 K-1 for NaBF4 and 0.55-0.65 W m-1 K-1 for KBF4. The thermal conductivity and diffusivity showed a gradual decrease up to the transition temperature and then rose slightly. Both materials show good thermal and structural stabilities over multiple heating/cooling cycles.

High-resolution powder X-ray data reveal the T(6) hexameric form of bovine insulin.

A series of bovine insulin samples were obtained as 14 polycrystalline precipitates at room temperature in the pH range 5.0-7.6. High-resolution powder X-ray diffraction data were collected to reveal the T6 hexameric insulin form. Sample homogeneity and reproducibility were verified by additional synchrotron measurements using an area detector. Pawley analyses of the powder patterns displayed pH- and radiation-induced anisotropic lattice modifications. The pronounced anisotropic lattice variations observed for T6 insulin were exploited in a 14-data-set Rietveld refinement to obtain an average crystal structure over the pH range investigated. Only the protein atoms of the known structure with PDB code 2a3g were employed in our starting model. A novel approach for refining protein structures using powder diffraction data is presented. In this approach, each amino acid is represented by a flexible rigid body (FRB). The FRB model requires a significantly smaller number of refinable parameters and restraints than a fully free-atom refinement. A total of 1542 stereochemical restraints were imposed in order to refine the positions of 800 protein atoms, two Zn atoms and 44 water molecules in the asymmetric unit using experimental data in the resolution range 18.2-2.7 Å for all profiles.

Irreversible network transformation in a dynamic porous host catalyzed by sulfur dioxide.

Porous NOTT-202a shows exceptionally high uptake of SO2, 13.6 mmol g(-1) (87.0 wt %) at 268 K and 1.0 bar, representing the highest value reported to date for a framework material. NOTT-202a undergoes a distinct irreversible framework phase transition upon SO2 uptake at 268-283 K to give NOTT-202b which has enhanced stability due to the formation of strong π···π interactions between interpenetrated networks.

Crystal structures and photoluminescence across the La2Si2O7-Ho2Si2O7 system.

It is well-known that when an RE2Si2O7 matrix is doped with active lanthanide ions, it displays promising luminescent responses for optical applications. The crystalline structure adopted by the silicate matrix as well as the distribution of the dopants among the available RE crystallographic sites have important effects on the luminescent yields of these compounds. The present study is aimed at analyzing the structural behavior as well as the luminescent properties of Ho(3+)-substituted La2Si2O7. Several compositions across the La2Si2O7-Ho2Si2O7 system were synthesized using the sol-gel method followed by calcination at 1600 °C. The resulting powders were analyzed by means of X-ray and neutron diffraction to determine the phase stabilities across the system. The results indicated a solid solubility region of G-(La,Ho)2Si2O7 which extends to the La0.6Ho1.4Si2O7 composition. Compositions richer in Ho(3+) show a two-phase domain (G+δ), while δ-(La,Ho)2Si2O7 is the stable phase for Ho(3+) contents higher than 90% (La0.2Ho1.8Si2O7). Anomalous diffraction data interestingly indicated that the La(3+) for Ho(3+) substitution mechanism in the G-(La,Ho)2Si2O7 polymorph is not homogeneous, but a preferential occupation of Ho(3+) for the RE2 site is observed. The Ho(3+)-doped G-La2Si2O7 phosphors exhibited a strong green luminescence after excitation at 446 nm. Lifetime measurements indicated that the optimum phosphor was that with a Ho(3+) content of 10%.

Hydrothermal synthesis, crystal structure, and catalytic potential of a one-dimensional molybdenum oxide/bipyridinedicarboxylate hybrid.

The reaction of MoO3, 2,2'-bipyridine-5,5-dicarboxylic acid (H2bpdc), water, and dimethylformamide in the mole ratio 1:1:1730:130 at 150 °C for 3 days in a rotating Teflon-lined digestion bomb leads to the isolation of the molybdenum oxide/bipyridinedicarboxylate hybrid material (DMA)[MoO3(Hbpdc)]·nH2O (1) (DMA = dimethylammonium). Compound 1 was characterized by scanning electron microscopy, FT-IR and (13)C{(1)H} CP MAS NMR spectroscopies, and elemental and thermogravimetric analyses. The solid state structure of 1 was solved and refined through Rietveld analysis of high resolution synchrotron X-ray powder diffraction data in conjunction with information derived from the above techniques. The material, crystallizing in the noncentrosymmetric monoclinic space group Pc, is composed of an anionic one-dimensional organic-inorganic hybrid polymer, ∞(1)[MoO3(Hbpdc)](-), formed by corner-sharing distorted {MoO4N2} octahedra, which cocrystallizes with charge-balancing DMA(+) cations and one water molecule per metal center. In the crystal structure of 1, the close packing of individual anionic polymers, DMA(+) cations, and water molecules is mediated by a series of supramolecular contacts, namely strong (O-H···O, N(+)-H···O(-)) and weak (C-H···O) hydrogen bonding interactions, and π-π contacts involving adjacent coordinated Hbpdc(-) ligands. The catalytic potential of 1 was investigated in the epoxidation reactions of the bioderived olefins methyl oleate (Ole) and DL-limonene (Lim) using tert-butylhydroperoxide (TBHP) as the oxygen donor and 1,2-dichloroethane (DCE) or (trifluoromethyl)benzene (BTF) as cosolvent, at 55 or 75 °C. Under these conditions, 1 acts as a source of active soluble species, leading to epoxide yields of up to 98% for methyl 9,10-epoxystearate (BTF, 75 °C, 100% conversion of Ole) and 89% for 1,2-epoxy-p-menth-8-ene (DCE, 55 °C, 95% conversion of Lim). Catalytic systems employing the ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide as solvent could be effectively recycled.

A-Site Cation Disorder in SrxBa1-xNb2O6 (x = 0.25, 0.33, 0.50, 0.61) Studied by High-Resolution Resonant X-ray Powder Diffraction.

The dielectric and ferroelectric properties of SrxBa1-xNb2O6 (SBN, 0.2 < x < 0.8) are known to be affected by the Sr fraction and can be further controlled by various quenching schemes. Changes in A-site cation configuration are believed to be linked to these changes in properties. In this work, we study the A-site cation disorder in SBN by the use of high-resolution resonant X-ray powder diffraction. The experimental results show that the larger Ba2+ is found exclusively on the larger A2 site, while Sr2+ is found on both the A1 and A2 sites, with an increasing amount on A2 with an increasing Sr fraction. At elevated temperatures, a small migration of Sr2+ from A1 to A2 is observed for SBN50 and SBN61. Linking this change in occupancies to changes in the average cation size on the A1 and A2 sites allows for rationalization of the property changes observed for quenched samples. Furthermore, SBN25 is shown to deviate from the tetragonal P4bm structure and is found to be orthorhombic with a Cmm2 structure.

The T2 structure of polycrystalline cubic human insulin.

The polymorphism of human insulin upon pH variation was characterized via X-ray powder diffraction, employing a crystallization protocol previously established for co-crystallization with phenolic derivatives. Two distinct rhombohedral (R3) polymorphs and one cubic (I213) polymorph were identified with increasing pH, corresponding to the T6, T3R3f and T2 conformations of insulin, respectively. The structure of the cubic T2 polymorph was determined via multi-profile stereochemically restrained Rietveld refinement at 2.7 Šresolution. This constitutes the first cubic insulin structure to be determined from crystals grown in the presence of zinc ions, although no zinc binding was observed. The differences of the polycrystalline variant from other cubic insulin structures, as well as the nature of the pH-driven phase transitions, are discussed in detail.

Hydrogen bonding patterns and C-H...π interactions in the structure of the antiparkinsonian drug (R)-rasagiline mesylate determined using laboratory and synchrotron X-ray powder diffraction data.

The structure of (R)-rasagiline mesylate [(R)-RasH+·Mes-], an active pharmaceutical ingredient used to treat Parkinson's disease, is presented. The structure was determined from laboratory and synchrotron powder diffraction data, refined using the Rietveld method, and validated and optimized using dispersion-corrected DFT calculations. The unit-cell parameters obtained in both experiments are in good agreement and the refinement with both datasets converged to good agreement factors. The final parameters obtained from laboratory data were a = 5.4905 (8), b = 6.536 (2), c = 38.953 (3) Å, V = 1398.0 (4) Å3 and from synchrotron powder data were a = 5.487530 (10) Å, b = 6.528939 (12) Å, c = 38.94313 (9) Å, V = 1395.245 (5) Å3 with Z = 4 and space group P212121. Preferred orientation was properly accounted for using the synchrotron radiation data, leading to a March-Dollase parameter of 1.140 (1) instead of the 0.642 (1) value obtained from laboratory data. In the structure, (R)-RasH+ moieties form layers parallel to the ab plane connected by mesylate ions through N-H...O and C-H...O hydrogen bonds. These layers stack along the c axis and are further connected by C-H...π interactions. Hirshfeld surface analysis and fingerprint plot calculations indicate that the main interactions are: H...H (50.9%), H...C/C...H (27.1%) and H...O/O...H (21.1%).

Structural studies of human insulin cocrystallized with phenol or resorcinol via powder diffraction.

The effects of the ligands phenol and resorcinol on the crystallization of human insulin have been investigated as a function of pH. Powder diffraction data were used to characterize several distinct polymorphic forms. A previously unknown polymorph with monoclinic symmetry (P2(1)) was identified for both types of ligand with similar characteristics [the unit-cell parameters for the insulin-resorcinol complex were a = 114.0228 (8), b = 335.43 (3), c = 49.211 (6) Å, ß = 101.531 (8)°].

Inclusion properties of volatile organic compounds in a calixarene-based organic zeolite.

The inclusion properties of a calixarene-based porous material have been studied to investigate the adsorption and the desorption of carbon tetrachloride, chloroform, and water in the zeolite-like structure. Uptake and release processes have been studied both by time-resolved powder X-ray diffraction and by thermogravimetric analysis to obtain structural and kinetic information. The selected guests are able to enter the structure with an increase in the host cell volume and with time-dependent diffusivity coefficients. Chloroform molecules act as a permanent porosity switch promoting a phase transition to non-porous triclinic form.

Triclinic-cubic phase transition and negative expansion in the actinide IV (Th, U, Np, Pu) diphosphates.

The AnP(2)O(7) diphosphates (An = Th, U, Np, Pu) have been synthesized by various routes depending on the stability of the An(IV) cation and its suitability for the unusual octahedral environment. Synchrotron and X-ray diffraction, thermal analysis, Raman spectroscopy, and (31)P nuclear magnetic resonance reveal them as a new family of diphosphates which probably includes the recently studied CeP(2)O(7). Although they adopt at high temperature the same cubic archetypal cell as the other known MP(2)O(7) diphosphates, they differ by a very faint triclinic distortion at room temperature that results from an ordering of the P(2)O(7) units, as shown using high-resolution synchrotron diffraction for UP(2)O(7). The uncommon triclinic-cubic phase transition is first order, and its temperature is very sensitive to the ionic radius of An(IV). The conflicting effects which control the thermal variations of the P-O-P angle are responsible for a strong expansion of the cell followed by a contraction at higher temperature. This inversion of expansion occurs at a temperature significantly higher than the phase transition, at variance with the parent compounds with smaller M(IV) cations in which the two phenomena coincide. As shown by various approaches, the P-O(b)-P linkage remains bent in the cubic form.

Acetylene and argon adsorption in a supramolecular organic zeolite.

The adsorption properties of a new nanoporous organic zeolite with respect to acetylene and Ar were studied by volumetric adsorption analysis, microcalorimetric experiments, and synchrotron high-resolution X-ray powder diffraction. This allowed us to locate the guest molecules inside the host channels and characterize the host-guest interactions.