Parametric analysis of glenoid implant design and fixation type.

Common post-operative problems in shoulder arthroplasty such as glenoid loosening and joint instability may be reduced by improvements in glenoid design, shape, material choice, and fixation method. A framework for parametric analysis of different implant fixation configurations was developed in order to efficiently sift through potential glenoid component designs. We investigated the influence of design factors such as fixation type, component thickness, and peg position, number, diameter, and length in a multi-factorial design investigation. The proposed method allowed for simultaneous comparison of the mechanical performance of 344 different parametric variations of 10 different reference geometries with either large central fixation features or small peripheral pegs, undergoing four different worst-case scenario loading conditions, and averaging 64.7 s per model. The impact of design parameters were assessed for different factors responsible for post-operative problems in shoulder arthroplasty, such as bone volume preservation, stresses in the implant, central displacement or fixation stability, and the worst performing geometries all relied on conventional central fixation. Of the remaining geometries, four peripheral fixation configurations produced von Mises stresses comfortably below the material's yield strength. We show that the developed method allows for simple, direct, rapid, and repeatable comparison of different design features, material choices, or fixation methods by analyzing how they influence the bone-implant mechanical environment. The proposed method can provide valuable insight in implant design optimization by screening through multiple potential design modifications at an early design evaluation stage and highlighting the best performing combinations according to the failure mechanism to mitigate. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:775-784, 2017.

Stability of small pegs for cementless implant fixation.

Most glenoid implants rely on large centrally located fixation features to avoid perforation of the glenoid vault in its peripheral regions. Upon revision of such components there may not be enough bone left for the reinsertion of an anatomical prosthesis. Multiple press-fit small pegs would allow for less bone resection and strong anchoring in the stiffer and denser peripheral subchondral bone. This study assessed the fixation characteristics, measured as the push-in (Pin ) and pull-out (Pout ) forces, and spring-back, measured as the elastic displacement immediately after insertion, for five different small press-fitted peg configurations manufactured out of UHMWPE cylinders (5 mm diameter and length). A total of 16 specimens for each configuration were tested in two types of solid bone substitute: Hard (40 PCF, 0.64 g/cm3 , worst-case scenario of Pin ) and soft (15 PCF, 0.24 g/cm3 , worst-case scenario of spring-back and Pout ). Two different diametric interference-fits were studied. Geometries with lower stiffness fins (large length to width aspect ratio) were the best performing designs in terms of primary fixation stability. They required the lowest force to fully seat, meaning they are less damaging to the bone during implantation, while providing the highest Pout /Pin ratio, indicating that when implanted they provide the strongest anchoring for the glenoid component. It is highlighted that drilling of chamfered holes could minimize spring-back displacements. These findings are relevant for the design of implants press-fitted pegs because primary fixation has been shown to be an important factor in achieving osseointegration and longevity of secondary fixation. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:2765-2772, 2017.

Deformation of the Lamina Cribrosa and Optic Nerve Due to Changes in Cerebrospinal Fluid Pressure.

Purpose: Cerebrospinal fluid pressure (CSFp) changes are involved or implicated in various ocular conditions including glaucoma, idiopathic intracranial hypertension, and visual impairment and intracranial pressure syndrome. However, little is known about the effects of CSFp on lamina cribrosa and retrolaminar neural tissue (RLNT) biomechanics, potentially important in these conditions. Our goal was to use an experimental approach to visualize and quantify the deformation of these tissues as CSFp increased. Methods: The posterior eye and RLNT of porcine eyes (n = 3) were imaged using synchrotron radiation phase-contrast micro-computed tomography (PC µCT) at an intraocular pressure of 15 mm Hg and CSFps of 4, 10, 20, and 30 mm Hg. Scans of each tissue region were acquired at each CSFp step and analyzed using digital volume correlation to determine 3-dimensional tissue deformations. Results: Elevating CSFp increased the strain in the lamina cribrosa and RLNT of all three specimens, with the largest strains occurring in the RLNT. Relative to the baseline CSFp of 4 mm Hg, at 30 mm Hg, the lamina cribrosa experienced a mean first and third principal strain of 4.4% and -3.5%, respectively. The corresponding values for the RLNT were 9.5% and -9.1%. Conclusions: CSFp has a significant impact on the strain distributions within the lamina cribrosa and, more prominently, within the RLNT. Elevations in CSFp were positively correlated with increasing deformations in each region and may play a role in ocular pathologies linked to changes in CSFp.

Consideration of multiple load cases is critical in modelling orthotropic bone adaptation in the femur.

Functional adaptation of the femur has been investigated in several studies by embedding bone remodelling algorithms in finite element (FE) models, with simplifications often made to the representation of bone's material symmetry and mechanical environment. An orthotropic strain-driven adaptation algorithm is proposed in order to predict the femur's volumetric material property distribution and directionality of its internal structures within a continuum. The algorithm was applied to a FE model of the femur, with muscles, ligaments and joints included explicitly. Multiple load cases representing distinct frames of two activities of daily living (walking and stair climbing) were considered. It is hypothesised that low shear moduli occur in areas of bone that are simply loaded and high shear moduli in areas subjected to complex loading conditions. In addition, it is investigated whether material properties of different femoral regions are stimulated by different activities. The loading and boundary conditions were considered to provide a physiological mechanical environment. The resulting volumetric material property distribution and directionalities agreed with ex vivo imaging data for the whole femur. Regions where non-orthogonal trabecular crossing has been documented coincided with higher values of predicted shear moduli. The topological influence of the different activities modelled was analysed. The influence of stair climbing on the properties of the femoral neck region is highlighted. It is recommended that multiple load cases should be considered when modelling bone adaptation. The orthotropic model of the complete femur is released with this study.

Effects of Peripapillary Scleral Stiffening on the Deformation of the Lamina Cribrosa.

PURPOSE: Scleral stiffening has been proposed as a treatment for glaucoma to protect the lamina cribrosa (LC) from excessive intraocular pressure-induced deformation. Here we experimentally evaluated the effects of moderate stiffening of the peripapillary sclera on the deformation of the LC. METHODS: An annular sponge, saturated with 1.25% glutaraldehyde, was applied to the external surface of the peripapillary sclera for 5 minutes to stiffen the sclera. Tissue deformation was quantified in two groups of porcine eyes, using digital image correlation (DIC) or computed tomography imaging and digital volume correlation (DVC). In group A (n = 14), eyes were subjected to inflation testing before and after scleral stiffening. Digital image correlation was used to measure scleral deformation and quantify the magnitude of scleral stiffening. In group B (n = 5), the optic nerve head region was imaged using synchrotron radiation phase-contrast microcomputed tomography (PC µCT) at an isotropic spatial resolution of 3.2 µm. Digital volume correlation was used to compute the full-field three-dimensional deformation within the LC and evaluate the effects of peripapillary scleral cross-linking on LC biomechanics. RESULTS: On average, scleral treatment with glutaraldehyde caused a 34 ± 14% stiffening of the peripapillary sclera measured at 17 mm Hg and a 47 ± 12% decrease in the maximum tensile strain in the LC measured at 15 mm Hg. The reduction in LC strains was not due to cross-linking of the LC. CONCLUSIONS: Peripapillary scleral stiffening is effective at reducing the magnitude of biomechanical strains within the LC. Its potential and future utilization in glaucoma axonal neuroprotection requires further investigation.

Phase-Contrast Micro-Computed Tomography Measurements of the Intraocular Pressure-Induced Deformation of the Porcine Lamina Cribrosa.

The lamina cribrosa (LC) is a complex mesh-like tissue in the posterior eye. Its biomechanical environment is thought to play a major role in glaucoma, the second most common cause of blindness. Due to its small size and relative inaccessibility, high-resolution measurements of LC deformation, important in characterizing LC biomechanics, are challenging. Here we present a novel noninvasive imaging method, which enables measurement of the three-dimensional deformation of the LC caused by acute elevation of intraocular pressure (IOP). Posterior segments of porcine eyes were imaged using synchrotron radiation phase contrast micro-computed tomography (PC µCT) at IOPs between 6 and 37 mmHg. The complex trabecular architecture of the LC was reconstructed with an isotropic spatial resolution of 3.2 µm. Scans acquired at different IOPs were analyzed with digital volume correlation (DVC) to compute full-field deformation within the LC. IOP elevation caused substantial tensile, shearing and compressive devformation within the LC, with maximum tensile strains at 30 mmHg averaging 5.5%, and compressive strains reaching 20%. We conclude that PC µCT provides a novel high-resolution method for imaging the LC, and when combined with DVC, allows for full-field 3D measurement of ex vivo LC biomechanics at high spatial resolution.

Digital volume correlation and micro-CT: An in-vitro technique for measuring full-field interface micromotion around polyethylene implants.

Micromotion around implants is commonly measured using displacement-sensor techniques. Due to the limitations of these techniques, an alternative approach (DVC-µCT) using digital volume correlation (DVC) and micro-CT (µCT) was developed in this study. The validation consisted of evaluating DVC-µCT based micromotion against known micromotions (40, 100 and 150 µm) in a simplified experiment. Subsequently, a more clinically realistic experiment in which a glenoid component was implanted into a porcine scapula was carried out and the DVC-µCT measurements during a single load cycle (duration 20 min due to scanning time) was correlated with the manual tracking of micromotion at 12 discrete points across the implant interface. In this same experiment the full-field DVC-µCT micromotion was compared to the full-field micromotion predicted by a parallel finite element analysis (FEA). It was found that DVC-µCT micromotion matched the known micromotion of the simplified experiment (average/peak error=1.4/1.7 µm, regression line slope=0.999) and correlated with the micromotion at the 12 points tracked manually during the realistic experiment (R(2)=0.96). The DVC-µCT full-field micromotion matched the pattern of the full-field FEA predicted micromotion. This study showed that the DVC-µCT technique provides sensible estimates of micromotion. The main advantages of this technique are that it does not damage important parts of the specimen to gain access to the bone-implant interface, and it provides a full-field evaluation of micromotion as opposed to the micromotion at just a few discrete points. In conclusion the DVC-µCT technique provides a useful tool for investigations of micromotion around plastic implants.

A comparative study of orthotropic and isotropic bone adaptation in the femur.

Functional adaptation of the femur has been studied extensively by embedding remodelling algorithms in finite element models, with bone commonly assumed to have isotropic material properties for computational efficiency. However, isotropy is insufficient in predicting the directionality of bone's observed microstructure. A novel iterative orthotropic 3D adaptation algorithm is proposed and applied to a finite element model of the whole femur. Bone was modelled as an optimised strain-driven adaptive continuum with local orthotropic symmetry. Each element's material orientations were aligned with the local principal stress directions and their corresponding directional Young's moduli updated proportionally to the associated strain stimuli. The converged predicted density distributions for a coronal section of the whole femur were qualitatively and quantitatively compared with the results obtained by the commonly used isotropic approach to bone adaptation and with ex vivo imaging data. The orthotropic assumption was shown to improve the prediction of bone density distribution when compared with the more commonly used isotropic approach, whilst producing lower comparative mass, structurally optimised models. It was also shown that the orthotropic approach can provide additional directional information on the material properties distributions for the whole femur, an advantage over isotropic bone adaptation. Orthotropic bone models can help in improving research areas in biomechanics where local structure and mechanical properties are of key importance, such as fracture prediction and implant assessment.