RESUMO
The thermal decomposition of perfluorooctanoic acid (PFOA) under oxidative conditions was investigated using air (O2) and N2O as oxidants over temperatures ranging from 400 to 1000 °C in an α-alumina reactor. In the presence of air, PFOA was found to decompose into perfluorohept-1-ene (C7F14) and perfluoroheptanoyl fluoride (C7F14O) in addition to HF, CO, and CO2. At temperatures above 800 °C, both C7F14 and C7F14O were no longer detected. A comprehensive analysis of the reaction mechanisms through quantum chemical analysis and kinetic modeling in combination with experimental observations was utilized to identify key reaction pathways. Quantum chemical analysis led to the conclusion that oxygen atoms are crucial in decomposing perfluoroalk-1-enes, especially the stable perfluorohept-1-ene (C7F14). Under oxidative conditions, it was found that significant quantities of C2F6 and CF4 were formed. Further quantum chemical analysis suggests that the O atoms facilitate the formation of volatile fluorinated compounds (VFCs) such as tetrafluoromethane (CF4) and hexafluoroethane (C2F6), particularly at higher temperatures. By elucidating these key reactions, an improved understanding of the potential formation products of incomplete combustion (PICs) or products of incomplete destruction (PIDs) is made.
RESUMO
The mobilization and transport of per- and poly-fluoroalkyl substances (PFASs) via surface runoff (runoff) from aqueous film-forming foam (AFFF)-contaminated soils during rainfall, flooding, or irrigation has not been thoroughly evaluated, and the effectiveness of carbonaceous sorbents in limiting PFASs in runoff is similarly unquantified. Here, laboratory-scale rainfall simulations evaluate PFAS losses in runoff and in leaching to groundwater (leachate) from AFFF-contaminated soils varying in texture, PFAS composition and concentration, and remediation treatment. Leaching dominated PFAS losses in soils with a concentration of ∑PFAS = 0.2-2 mg/kg. However, with higher soil PFAS concentrations (∑PFAS = 31 mg/kg), leachate volumes were negligible and runoff dominated losses. The concentration and variety of PFASs were far greater in leachates regardless of the initial concentrations in soil. Losses of PFASs were dependent on the C-chain length for leachates and more on the initial concentration in soil for runoff. Suspended materials did not meaningfully contribute to runoff losses. While concentrations of most PFASs declined significantly after the first rainfall event, desorption and transport in both runoff and leachates persisted over several rainfall events. Finally, results showed that sorption to AC mostly occurred during, not prior to, rainfall events and that 1% w/w AC substantially reduced losses in runoff and leachates from all soils.
Assuntos
Fluorocarbonos , Água Subterrânea , Poluentes Químicos da Água , Fluorocarbonos/análise , Poluentes Químicos da Água/análise , Solo , Poluição Ambiental , Água , AerossóisRESUMO
Soil contaminated with aqueous film-forming foams (AFFFs) containing per- and polyfluoroalkyl substances (PFASs) at firefighting training sites has become a major concern worldwide. To date, most studies have focused on assessing soil-water partitioning behavior of PFASs and the key factors that can affect their sorption, whereas PFASs leaching from contaminated soils have not yet been widely investigated. This study evaluated the leaching and desorption of a wide range of PFASs from twelve contaminated soils using the Australian Standard Leaching Procedure (ASLP), the U.S. EPA Multiple Extraction Procedure (MEP), and Leaching Environmental Assessment Framework (LEAF). All three leaching tests provided a similar assessment of PFAS leaching behavior. Leaching of PFASs from soils was related to C-chain lengths and their functional head groups. While short-chain (CF2 ≤ 6) PFASs were easily desorbed and leached, long-chain PFASs were more difficult to desorb. PFASs with a carboxylate head group were leached more readily and to a greater extent than those with a sulfonate or sulfonamide head group. Leaching of long-chain PFASs was pH-dependent where leaching increased at high pH, while leaching of short-chain PFASs was less sensitive to pH. Comparing different leaching tests showed that the results using the alkaline ASLP were similar to the cumulative MEP data and the former might be more practical for routine use than the MEP. No single soil property was adequately able to describe PFAS leaching from the soils. Overall, the PFAS chemical structure appeared to have a greater effect on PFAS leaching from soil than soil physicochemical properties.
Assuntos
Fluorocarbonos , Poluentes Químicos da Água , Austrália , Poluição Ambiental , Fluorocarbonos/análise , Solo/química , Poluentes Químicos da Água/análiseRESUMO
This study investigated the mobilization of a wide range of per- and polyfluoroalkyl substances (PFASs) present in aqueous film-forming foams (AFFFs) in water-saturated soils through one-dimensional (1-D) column experiments with a view to assessing the feasibility of their remediation by soil desorption and washing. Results indicated that sorption/desorption of most of the shorter-carbon-chain PFASs (C ≤ 6) in soil reached greater than 99% rapidlyâafter approximately two pore volumes (PVs) and were well predicted by an equilibrium transport model, indicating that they will be readily removed by soil washing technologies. In contrast, the equilibrium model failed to predict the mobilization of longer-chain PFASs (C ≥ 7), indicating the presence of nonequilibrium sorption/desorption (confirmed by a flow interruption experiment). The actual time taken to attain 99% sorption/desorption was up to 5 times longer than predicted by the equilibrium model (e.g., â¼62 PVs versus â¼12 PVs predicted for perfluorooctane sulfonate (PFOS) in loamy sand). The increasing contribution of hydrophobic interactions over the electrostatic interactions is suggested as the main driving factor of the nonequilibrium processes. The inverse linear relationship (R2 = 0.6, p < 0.0001) between the nonequilibrium mass transfer rate coefficient and the Freundlich sorption coefficient could potentially be a useful means for preliminary evaluation of potential nonequilibrium sorption/desorption of PFASs in soils.
Assuntos
Fluorocarbonos , Poluentes do Solo , Poluentes Químicos da Água , Fluorocarbonos/análise , Solo/química , Água , Poluentes Químicos da Água/análiseRESUMO
The aim of this study was to assess the soil-water partitioning behavior of a wider range of per- and polyfluoroalkyl substances (PFASs) onto soils covering diverse soil properties. The PFASs studied include perfluoroalkyl carboxylates (PFCAs), perfluoroalkane sulfonates (PFSAs), fluorotelomer sulfonates (FTSs), nonionic perfluoroalkane sulfonamides (FASAs), cyclic PFAS (PFEtCHxS), per- and polyfluoroalkyl ether acids (GenX, ADONA, 9Cl-PF3ONS), and three aqueous film-forming foam (AFFF)-related zwitterionic PFASs (AmPr-FHxSA, TAmPr-FHxSA, 6:2 FTSA-PrB). Soil-water partitioning coefficients (logâ¯Kd values) of the PFASs ranged from less than zero to approximately three, were chain-length-dependent, and were significantly linearly related to molecular weight (MW) for PFASs with MW > 350 g/mol (R2 = 0.94, p < 0.0001). Across all soils, the Kd values of all short-chain PFASs (≤5 -CF2- moieties) were similar and varied less (<0.5â¯log units) compared to long-chain PFASs (>0.5 to 1.5â¯â¯log units) and zwitterions AmPr- and TAmPr-FHxSA (â¼1.5 to 2â¯log units). Multiple soil properties described sorption of PFASs better than any single property. The effects of soil properties on sorption were different for anionic, nonionic, and zwitterionic PFASs. Solution pH could change both PFAS speciation and soil chemistry affecting surface complexation and electrostatic processes. The Kd values of all PFASs increased when solution pH decreased from approximately eight to three. Short-chain PFASs were less sensitive to solution pH than long-chain PFASs. The results indicate the complex interactions of PFASs with soil surfaces and the need to consider both PFAS type and soil properties to describe mobility in the environment.
Assuntos
Fluorocarbonos , Poluentes Químicos da Água , Fluorocarbonos/análise , Concentração de Íons de Hidrogênio , Solo , Água , Poluentes Químicos da Água/análiseRESUMO
Per- and poly-fluoroalkyl substances (PFASs) are contaminants of emerging concern, yet the understanding of factors that control their leaching and release from contaminated soils remains limited. This study aimed to investigate the impact of dissolved organic carbon (DOC) on the release of PFASs-specifically, perfluorohexane sulfonate (PFHxS), perfluorooctane sulfonate (PFOS), and perfluorooctanoic acid (PFOA)from soils contaminated by aqueous film forming foam (AFFF). Batch aqueous leaching experiments were conducted on AFFF-contaminated soils under alkaline solution conditions (pH 9.5, 10.5, and 12) as it enhances leaching of both PFAS and DOC. Leaching of PFOS was significantly increased under alkaline conditions. Although the leaching of PFAS generally increased with pH, PFOS appeared to be more retained under the very alkaline pH conditions used in this study. At the same solution pH, leaching of PFOS and DOC was less in Ca(OH)2 than in NaOH. The retention of PFOS under these conditions may be attributable to the shielding of the negative charge of the soil components and colloids (e.g., DOC and clay minerals) in the leachates and/or the screening of negative charges on head groups of PFOS due to the high concentration of divalent cations. Solution chemistry affected desorption of PFOS more than PFHxS and PFOA. The study highlights that the influence of DOC on PFAS leaching and transport can be very complex, and depends on leachate chemistry (e.g., pH and cation type), PFAS chemistry, the magnitude of PFAS contamination and factors that influence the solid:liquid partitioning of organic carbon in soil.
Assuntos
Ácidos Alcanossulfônicos , Carbono , Fluorocarbonos , Poluentes do Solo , Solo , Fluorocarbonos/química , Poluentes do Solo/química , Solo/química , Carbono/química , Ácidos Alcanossulfônicos/química , Concentração de Íons de Hidrogênio , Caprilatos/química , Adsorção , Ácidos SulfônicosRESUMO
Removal of per- and polyfluoroalkyl substances (PFASs) from water or their immobilization in soil using carbon-based sorbents is one of the cost-effective techniques. Considering the variety of carbon-based sorbents, identifying the key sorbent properties responsible for PFASs removal from solution or immobilization in the soil can assist in the selection of the best sorbents for management of contaminated sites. This study evaluated the performance of 28 carbon-based sorbents including granular and powdered activated carbon (GAC and PAC), mixed mode carbon mineral material, biochars, and graphene-based materials (GNBs). The sorbents were characterized for a range of physical and chemical properties. PFASs' sorption from an AFFF-spiked solution was examined via a batch experiment, while their ability to immobilize PFASs in soil was tested following mixing, incubation and extraction using the Australian Standard Leaching Procedure. Both soil and solution were treated with 1 % w/w sorbents. Comparing different carbon-based materials, PAC, mixed mode carbon mineral material and GAC were the most effective in sorbing PFASs in both solution and soil. Among the different physical characteristics measured, the sorption of long-chain and more hydrophobic PFASs in both soil and solution was best correlated with sorbent surface area measured using methylene blue, which highlights the importance of mesopores in PFASs sorption. Iodine number was found to be a better indicator of the sorption of short-chain and more hydrophilic PFASs from solution but was found to be poorly correlated with PFASs immobilization in soil for activated carbons. Sorbents with a net positive charge performed better than those with a net negative charge, or no net charge. This study showed that surface area measured by methylene blue and surface charge are the best indicators of sorbent performance with respect to sorption/reducing leaching of PFASs. These properties may be helpful in selecting sorbents for PFASs remediation of soils/waters.
RESUMO
This paper aims to describe the performance of a soil washing plant (SWP) for remediating a per- and poly-fluoroalkyl substances (PFASs)-contaminated soil with a high clay content (61%). The SWP used both physical and chemical processes; fractionation of the soil particles by size and partitioning of PFASs into the aqueous phase to remove PFASs from the soil. Contaminated water was treated in series with granulated activated carbon (GAC) and ion-exchange resin and reused within the SWP. Approximately 2200 t (dry weight) of PFAS-contaminated soil was treated in 25 batches of 90 t each, with a throughput of approximately 11 t soil/hr. Efficiency of the SWP was measured by observed decreases in total and leachable concentrations of PFASs in the soil. Average removal efficiencies (RE) were up to 97.1% for perfluorocarboxylic acids and 94.9% for perfluorosulfonic acids. REs varied among different PFASs depending on their chemistry (functional head group, carbon chain length) and were independent of the total PFAS concentrations in each soil batch. Mass balance analysis found approximately 90% of the PFAS mass in the soil was transferred to the wash solution and > 99.9% of the PFAS mass in the wash solution was transferred onto the GAC without any breakthrough.
Assuntos
Fluorocarbonos , Poluentes Químicos da Água , Solo/química , Fluorocarbonos/análise , Poluentes Químicos da Água/análise , Argila , Poluição da Água/análise , Carvão Vegetal , PlantasRESUMO
Chlorpyrifos (CPF) is a widely used pesticide; however, limited experimental work has been completed on its thermal decomposition. CPF is known to decompose into 3,5,6-trichloro-2-pyridinol (TCpyol) together with ethylene and HOPOS. Under oxidative conditions TCpyol can decompose into the dioxin-like 2,3,7,8-tetrachloro-[1,4]-dioxinodipyridine (TCDDPy). With CPF on the cusp of being banned in several jurisdictions worldwide, the question might arise as to how to safely eliminate large stockpiles of this pesticide. Thermal methods such as incineration or thermal desorption of pesticide-contaminated soils are often employed. To assess the safety of thermal methods, information about the toxicants arising from thermal treatment is essential. The present flow reactor study reports the products detected under inert and oxidative conditions from the decomposition of CPF representative of thermal treatments and of wildfires in CPF-contaminated vegetation. Ethylene and TCpyol are the initial products formed at temperatures between 550 and 650 °C, although the detection of HOPOS as a reaction product has proven to be elusive. During pyrolysis of CPF in an inert gas, the dominant sulfur-containing product detected from CPF is carbon disulfide. Quantum chemical analysis reveals that ethylene and HOPOS undergo a facile reaction to form thiirane (c-C2H4S) which subsequently undergoes ring opening reactions to form precursors of CS2. At elevated temperatures (>650 °C), TCpyol undergoes both decarbonylation and dehydroxylation reactions together with decomposition of its primary product, TCpyol. A substantial number of toxicants is observed, including HCN and several nitriles, including cyanogen. No CS2 is observed under oxidative conditions - sulfur dioxide is the fate of S in oxidation of CPF, and quantum chemical studies show that SO2 formation is initiated by the reaction between HOPOS and O2. The range of toxicants produced in thermal decomposition of CPF is summarised.