Comparative Evaluation of Dissolution Performance in a USP 2 Setup and Alternative Stirrers and Vessel Designs: A Systematic Computational Investigation.

The dissolution testing method described in the United States Pharmacopeia (USP) Chapter ⟨711⟩ is widely used for assessing the release of active pharmaceutical ingredients from solid dosage forms. However, extensive use over the years has revealed certain issues, including high experimental intervariability observed in specific formulations and the settling of particles in the dead zone of the vessel. To address these concerns and gain a comprehensive understanding of the hydrodynamic conditions within the USP 2 apparatus, computational fluid dynamic simulations have been employed in this study. The base design employed in this study is the 900 mL USP 2 vessel along with a paddle stirrer at a 50 rpm rotational speed. Additionally, alternative stirrer designs, including the hydrofoil, pitched blade, and Rushton impeller, are investigated. A comparison is also made between a flat-bottom tank and the USP round-bottom vessel of the same volume and diameter. Furthermore, this work examines the impact of various parameters, such as clearance distance (distance between the bottom of the impeller and bottom of the vessel), number of impeller blades, impeller diameter, and impeller attachment angle. The volume-average shear rate (Stv), fluid velocity (Utv), and energy dissipation rates (ϵtv) represent the key properties evaluated in this study. Comparing the USP2 design and systems with the same stirrer but flat-bottom vessel reveals more homogeneous mixing compared to the USP2 design. Analyzing fluid flow streamlines in different designs demonstrates that hydrofoil stirrers generate more suspension or upward movement of fluid compared to paddle stirrers. Therefore, when impellers are of a similar size, hydrofoil designs generate higher fluid velocities in the coning area. Furthermore, the angle of blade attachment to the hub influences the fluid velocity in the coning area in a way that the 60° angle design generates more suspension than the 45° angle design. The findings indicate that the paddle stirrer design leads to a heterogeneous shear rate and velocity distributions within the vessel compared with the other designs, suggesting suboptimal performance. These insights provide valuable guidance for the development of improved in vitro dissolution testing devices, emphasizing the importance of optimized design considerations to minimize hydrodynamic variability, enhance dissolution characterization, and reduce variability in dissolution test results. Ultimately, such advancements hold potential for improving in vitro-in vivo correlations in drug development.

Digitalizing the TIM-1 Model Using Computational Approaches─Part Two: Digital TIM-1 Model in GastroPlus.

A TIM-1 model is an in vitro gastrointestinal (GI) simulator considering crucial physiological parameters that will affect the in vivo drug release process. The outcome of these experiments can indicate the critical bioavailability attributes (CBAs) that will impact the fraction absorbed in vivo. The model is widely used in the nonclinical stage of drug product development to assess the bioaccessible fraction of drugs for numerous candidate formulations. In this work, we developed a digital TIM-1 model in the GastroPlus platform. In a first step, we performed validation experiments to assess the luminal concentrations and bioaccessible fractions for two marker compounds. The digital TIM-1 was able to adequately reflect the luminal concentrations and bioaccessible fractions of these markers under different prandial conditions, confirming the appropriate integration of mass transfer in the TIM-1 model. In a second set of experiments, a case example with PF-07059013 was performed, where luminal concentrations and bioaccessible fractions were predicted for 200 and 1000 mg doses under fasted and achlorhydric conditions. Experimental and simulated data pointed out that the achlorhydric effect was more pronounced at the 1000 mg dose, showing a solubility-limited dissolution and, consequently, decreased bioaccessible fraction. Toward future applications, the digital TIM-1 model will be thoroughly applied to explore a link between in vitro and in vivo outcomes based on more case examples with model compounds with the access of TIM-1 and plasma data. Ideally, this digital TIM-1 can be directly used in GastroPlus to explore an in vitro-in vivo correlation (IVIVC) between the fraction dissolved (digital TIM-1 settings) and the fraction absorbed (human PBPK settings).

Digitalizing the TIM-1 Model using Computational Approaches-Part One: TIM-1 Data Explorer.

The TIM-1 gastrointestinal model is one of the most advanced in vitro systems currently available for biorelevant dissolution testing. This technology, the initial version of which was developed nearly 30 years ago and has been subject to a number of significant updates over this period, simulates the dynamic environment of the human gastrointestinal tract, including pH, transfer times, secretion of bile, enzymes, and electrolytes. In the pharmaceutical industry, the TIM-1 system is used to support drug product design and provide a biopredictive assessment of drug product performance. Typically, the bioaccessibility data sets generated by TIM-1 experiments are used to qualitatively compare formulation performance, and the use of bioaccessibility data as inputs for physiologically based pharmacokinetic (PBPK) modeling for quantitative predictions is limited. To expand the utility of the TIM-1 model beyond standard bioaccessibility measurements (which define the fraction available for absorption), we have developed a computational tool, TIM-1 Data Explorer, to describe the fluid and mass balance within the TIM-1 system. The use of this tool allows a detailed inspection and in-depth interpretation of the experimental data. In addition to mass balance calculation, this model also can be used to describe the critical processes a drug substance would undergo during a TIM-1 experiment, such as dissolution, precipitation on transfer from the stomach to duodenum, and redissolution. The TIM-1 Data Explorer was validated in two case studies. In the first case study with paracetamol, we have shown the ability of the simulator to adequately describe mass transfer events within the TIM-1 system, and in the second study with a weakly basic in-house compound, PF-07059013, the TIM-1 Data Explorer was successfully used to describe dissolution and precipitation processes.

Effect of Food and a Proton-Pump Inhibitor on the Absorption of Encorafenib: An In Vivo-In Vitro-In Silico Approach.

Encorafenib is a kinase inhibitor indicated for the treatment of patients with BRAF mutant melanoma and BRAF mutant metastatic colorectal cancer. To understand the effect of food and coadministration with a proton-pump inhibitor (PPI), in vitro, in vivo, and in silico data were generated to optimize the clinical dose, evaluate safety, and better understand the oral absorption process under these conditions. Study 1 evaluated the effect of food on the plasma pharmacokinetics, safety, and tolerability after a single oral dose of encorafenib 100 mg. Study 2 evaluated the same end points with coadministration of encorafenib and rabeprazole (PPI perpetrator). The in vitro gastrointestinal TIM-1 model was used to investigate the release of encorafenib and the amount available for absorption under different testing conditions (fasted, fed, and with the use of a PPI). The fasted, fed, and PPI states were predicted for the encorafenib commercial capsule in GastroPlus 9.8. In study 1, both AUCinf and AUClast decreased by 4% with the administration of a high-fat meal. The Cmax was 36% lower than with fasted conditions. All 3 exposure parameters in study 2 (AUCinf, AUClast, and Cmax) had mean changes of <10% when encorafenib was coadministered with a PPI. Using the in vitro gastrointestinal simulator TIM-1, the model demonstrated a similar release of drug, as the bioaccessible fraction, in the 3 conditions was equal (≥80%), predicting no PPI or food effect for this drug formulation. The modeling in GastroPlus 9.8 demonstrated complete absorption of encorafenib when formulated as an amorphous solid dispersion. To obtain these results, it was crucial to integrate the amorphous solubility of the drug that shows a 20-fold higher solubility at pH 6.8 compared with crystalline solubility. The increased amorphous solubility is likely the reason no PPI effect was observed compared with fasted state conditions. The prolongation in gastric emptying in the fed state resulted in delayed plasma Tmax for encorafenib. No dose adjustment is necessary when encorafenib is administered in the fed state or when coadministered with a PPI. Both the TIM-1 and physiologically based pharmacokinetic model results were consistent with the observed clinical data, suggesting that these will be valuable tools for future work.

Favipiravir at high doses has potent antiviral activity in SARS-CoV-2-infected hamsters, whereas hydroxychloroquine lacks activity.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) rapidly spread around the globe after its emergence in Wuhan in December 2019. With no specific therapeutic and prophylactic options available, the virus has infected millions of people of which more than half a million succumbed to the viral disease, COVID-19. The urgent need for an effective treatment together with a lack of small animal infection models has led to clinical trials using repurposed drugs without preclinical evidence of their in vivo efficacy. We established an infection model in Syrian hamsters to evaluate the efficacy of small molecules on both infection and transmission. Treatment of SARS-CoV-2-infected hamsters with a low dose of favipiravir or hydroxychloroquine with(out) azithromycin resulted in, respectively, a mild or no reduction in virus levels. However, high doses of favipiravir significantly reduced infectious virus titers in the lungs and markedly improved lung histopathology. Moreover, a high dose of favipiravir decreased virus transmission by direct contact, whereas hydroxychloroquine failed as prophylaxis. Pharmacokinetic modeling of hydroxychloroquine suggested that the total lung exposure to the drug did not cause the failure. Our data on hydroxychloroquine (together with previous reports in macaques and ferrets) thus provide no scientific basis for the use of this drug in COVID-19 patients. In contrast, the results with favipiravir demonstrate that an antiviral drug at nontoxic doses exhibits a marked protective effect against SARS-CoV-2 in a small animal model. Clinical studies are required to assess whether a similar antiviral effect is achievable in humans without toxic effects.

Exploring the Predictive Power of the In Situ Perfusion Technique towards Drug Absorption: Theory, Practice, and Applications.

Considering the broad applications and popularity, the in situ perfusion technique is an established and interesting approach to evaluate the absorption mechanisms of drug molecules in specific regions of the intestinal tract. Compared to perfusion studies in humans, this surrogate model shows several familiar characteristics making it interesting to apply this technique in rats in the non-clinical stage of drug product development. The differences in gastrointestinal (GI) anatomy and physiology between rats and humans are thoroughly discussed in the present review. Moreover, an in-depth overview of the Doluisio (i.e., closed-loop) versus the single-pass intestinal perfusion (i.e., open-loop) technique is shown. Finally, applications and future perspectives of the technique are presented.

Haematoma evacuation in cerebellar intracerebral haemorrhage: systematic review.

BACKGROUND: Guidelines regarding recommendations for surgical treatment of spontaneous cerebellar intracerebral haemorrhage (ICH) differ. We aimed to systematically review the literature to assess treatment strategies and outcomes. METHODS: We searched PubMed and Embase between 1970 and 2019 for randomised or otherwise controlled studies and observational cohort studies. We included studies according to predefined selection criteria and assessed their quality according to the Newcastle-Ottawa Scale (NOS) and risk of bias according to a predefined scale. We assessed case fatality and functional outcome in patients treated conservatively or with haematoma evacuation. Favourable functional outcome was defined as a modified Rankin Scale score of 0-2 or a Glasgow Outcome Scale score of 4-5. RESULTS: We included 41 observational cohort studies describing 2062 patients (40% female) with spontaneous cerebellar ICH. A total of 1171 patients (57%) underwent haematoma evacuation. Ten studies described a cohort of surgically treated patients (n=533) and 31 cohorts with both surgically and conservatively treated patients (n=638 and n=891, respectively). There were no randomised clinical trials nor studies comparing outcome between the groups after adjustment for differences in baseline characteristics. The median NOS score (IQR) was 5 (4-6) out of 8 points and the bias score was 2 (1-3) out of 8, indicative of high risk of bias. Case fatality at discharge was 21% (95% CI 17% to 25%) after conservative treatment and 24% (95% CI 19% to 29%) after haematoma evacuation. At ≥6 months after conservative treatment, case fatality was 30% (95% CI 25% to 30%) and favourable functional outcome was 45% (95% CI 40% to 50%) and after haematoma evacuation, case fatality was 34% (95% CI 30% to 38%) and 42% (95% CI 37% to 47%). CONCLUSIONS: Controlled studies on the effect of neurosurgical treatment in patients with spontaneous cerebellar ICH are lacking, and the risk of bias in published series is high. Due to substantial differences in patient characteristics between conservatively and surgically treated patients, and high variability in treatment indications, a meaningful comparison in outcomes could not be made. There is no good published evidence to support treatment recommendations and controlled, preferably randomised studies are warranted in order to formulate evidence-based treatment guidelines for patients with cerebellar ICH.

Translational Modeling Strategies for Orally Administered Drug Products: Academic, Industrial and Regulatory Perspectives.

During non-clinical and clinical development of a new molecular entity (NME), modeling and simulation (M&S) are routinely used to predict the exposure and pharmacokinetics (PK) of the drug compound in humans. The basic methodology and output are generally understood across all functional disciplines. However, this understanding is mostly restricted to traditional methods such as those in simplified kinetic models and void of adequate mechanistic foundation to address questions beyond the observed clinical data. In the past two decades, alternative and more mechanistic methods, particularly for describing absorption, distribution, excretion and metabolism (ADME) of drugs have been developed and applied under the general umbrella of physiologically-based pharmacokinetic (PBPK) methods. Their mechanistic nature gives the ability to ask many other questions which were not traditionally asked and provide some logically and evidenced-based potential answers. Whilst traditional PK methods are mainstream and understood by most scientists, mechanistic absorption models alongside other PBPK approaches are still deemed eclectic, despite making significant strides in the fundamental science as well as regulatory acceptance. On November 3rd, a short course was held at the annual American Association of Pharmaceutical Scientists (AAPS) meeting in San Antonio, Texas. The different talks were tailored to provide a basis or rationale for the subject, introduction to fundamental principles with historical perspective, a critique of the state-of-the-art, examples of successful application of the methods across different phases of the drug development process and the specific standards these mechanistic models should meet to be fully reliable from a regulatory perspective.

Mass Transport Analysis of the Enhanced Buffer Capacity of the Bicarbonate-CO2 Buffer in a Phase-Heterogenous System: Physiological and Pharmaceutical Significance.

The bicarbonate buffer capacity is usually considered in a phase-homogeneous system, at equilibrium, with no CO2 transfer between the liquid buffer phase and another phase. However, typically, an in vitro bicarbonate buffer-based system is a phase-heterogeneous system, as it entails continuously sparging (bubbling) the dissolution medium with CO2 in a gas mixture, at constant ratio, to maintain a constant partial pressure of CO2 (g) and CO2(aq) molarity at a prescribed value, with CO2 diffusing freely between the gas and the aqueous phases. The human gastrointestinal tract is also a phase-heterogeneous system, with CO2 diffusing across the mucosal membrane into the mesenteric arterial blood, which serves as a sink for CO2 from the intestinal lumen. In this report, a mass transport analysis of the apparent buffer capacity of a phase-heterogeneous bicarbonate-CO2 system is developed. It is shown that, most significantly, a phase-heterogeneous bicarbonate-CO2 system can have a much higher buffer capacity than a phase-homogeneous system such that the buffer capacity is dependent on the bicarbonate concentration. It is double that of a phase-homogeneous system at the pH = p Ka for a monoprotic buffer at the same concentration. This buffer capacity enhancement increases hyperbolically with pH above the p Ka, thus providing a much stronger buffering to keep the pH in the physiologically neutral range. The buffer capacity will be dependent on the bicarbonate molarity (which in vivo will depend on the bicarbonate secretion rate) and not the pH of the luminal fluid. Further, there is no conjugate acid accumulation as a result of bicarbonate neutralization, since the resulting carbonic acid (H2CO3) rapidly dehydrates producing CO2 and H2O. The mass transport analysis developed in this report is further supported by in vitro experimental results. This enhanced bicarbonate buffer capacity in a phase-heterogeneous system is of physiological significance as well as significant for the dissolution and absorption of ionizable drugs.

Linking the Gastrointestinal Behavior of Ibuprofen with the Systemic Exposure between and within Humans-Part 1: Fasted State Conditions.

The goal of this project was to explore and to statistically evaluate the responsible gastrointestinal (GI) factors that are significant factors in explaining the systemic exposure of ibuprofen, between and within human subjects. In a previous study, we determined the solution and total concentrations of ibuprofen as a function of time in aspirated GI fluids, after oral administration of an 800 mg IR tablet (reference standard) of ibuprofen to 20 healthy volunteers in fasted state conditions. In addition, we determined luminal pH and motility pressure recordings that were simultaneously monitored along the GI tract. Blood samples were taken to determine ibuprofen plasma levels. In this work, an in-depth statistical and pharmacokinetic analysis was performed to explain which underlying GI variables are determining the systemic concentrations of ibuprofen between (inter-) and within (intra-) subjects. In addition, the obtained plasma profiles were deconvoluted to link the fraction absorbed with the fraction dissolved. Multiple linear regressions were performed to explain and quantitatively express the impact of underlying GI physiology on systemic exposure of the drug (in terms of plasma Cmax/AUC and plasma Tmax). The exploratory analysis of the correlation between plasma Cmax/AUC and the time to the first phase III contractions postdose (TMMC-III) explains ∼40% of the variability in plasma Cmax for all fasted state subjects. We have experimentally shown that the in vivo intestinal dissolution of ibuprofen is dependent upon physiological variables like, in this case, pH and postdose phase III contractions. For the first time, this work presents a thorough statistical analysis explaining how the GI behavior of an ionized drug can explain the systemic exposure of the drug based on the individual profiles of participating subjects. This creates a scientifically based and rational framework that emphasizes the importance of including pH and motility in a predictive in vivo dissolution methodology to forecast the in vivo performance of a drug product. Moreover, as no extensive first-pass metabolism is considered for ibuprofen, this study demonstrates how intraluminal drug behavior is reflecting the systemic exposure of a drug.

Linking the Gastrointestinal Behavior of Ibuprofen with the Systemic Exposure between and within Humans-Part 2: Fed State.

Exploring the intraluminal behavior of an oral drug product in the human gastrointestinal (GI) tract remains challenging. Many in vivo techniques are available to investigate the impact of GI physiology on oral drug behavior in fasting state conditions. However, little is known about the intraluminal behavior of a drug in postprandial conditions. In a previous report, we described the mean solution and total concentrations of ibuprofen after oral administration of an immediate-release (IR) tablet in fed state conditions. In parallel, blood samples were taken to assess systemic concentrations. The purpose of this work was to statistically evaluate the impact of GI physiology (e.g., pH, contractile events) within and between individuals (intra and intersubject variability) for a total of 17 healthy subjects. In addition, a pharmacokinetic (PK) analysis was performed by noncompartmental analysis, and PK parameters were correlated with underlying physiological factors (pH, time to phase III contractions postdose) and study parameters (e.g., ingested amount of calories, coadministered water). Moreover, individual plasma profiles were deconvoluted to assess the fraction absorbed as a function of time, demonstrating the link between intraluminal and systemic behavior of the drug. The results demonstrated that the in vivo dissolution of ibuprofen depends on the present gastric pH and motility events at the time of administration. Both intraluminal factors were responsible for explaining 63% of plasma Cmax variability among all individuals. For the first time, an in-depth analysis was performed on a large data set derived from an aspiration/motility study, quantifying the impact of physiology on systemic behavior of an orally administered drug product in fed state conditions. The data obtained from this study will help us to develop an in vitro biorelevant dissolution approach and optimize in silico tools in order to predict the in vivo performance of orally administered drug products, especially in fed state conditions.

In Silico Modeling Approach for the Evaluation of Gastrointestinal Dissolution, Supersaturation, and Precipitation of Posaconazole.

The aim of this study was to evaluate gastrointestinal (GI) dissolution, supersaturation, and precipitation of posaconazole, formulated as an acidified (pH 1.6) and neutral (pH 7.1) suspension. A physiologically based pharmacokinetic (PBPK) modeling and simulation tool was applied to simulate GI and systemic concentration-time profiles of posaconazole, which were directly compared with intraluminal and systemic data measured in humans. The Advanced Dissolution Absorption and Metabolism (ADAM) model of the Simcyp Simulator correctly simulated incomplete gastric dissolution and saturated duodenal concentrations of posaconazole in the duodenal fluids following administration of the neutral suspension. In contrast, gastric dissolution was approximately 2-fold higher after administration of the acidified suspension, which resulted in supersaturated concentrations of posaconazole upon transfer to the upper small intestine. The precipitation kinetics of posaconazole were described by two precipitation rate constants, extracted by semimechanistic modeling of a two-stage medium change in vitro dissolution test. The 2-fold difference in exposure in the duodenal compartment for the two formulations corresponded with a 2-fold difference in systemic exposure. This study demonstrated for the first time predictive in silico simulations of GI dissolution, supersaturation, and precipitation for a weakly basic compound in part informed by modeling of in vitro dissolution experiments and validated via clinical measurements in both GI fluids and plasma. Sensitivity analysis with the PBPK model indicated that the critical supersaturation ratio (CSR) and second precipitation rate constant (sPRC) are important parameters of the model. Due to the limitations of the two-stage medium change experiment the CSR was extracted directly from the clinical data. However, in vitro experiments with the BioGIT transfer system performed after completion of the in silico modeling provided an almost identical CSR to the clinical study value; this had no significant impact on the PBPK model predictions.

Low Buffer Capacity and Alternating Motility along the Human Gastrointestinal Tract: Implications for in Vivo Dissolution and Absorption of Ionizable Drugs.

In this study, we determined the pH and buffer capacity of human gastrointestinal (GI) fluids (aspirated from the stomach, duodenum, proximal jejunum, and mid/distal jejunum) as a function of time, from 37 healthy subjects after oral administration of an 800 mg immediate-release tablet of ibuprofen (reference listed drug; RLD) under typical prescribed bioequivalence (BE) study protocol conditions in both fasted and fed states (simulated by ingestion of a liquid meal). Simultaneously, motility was continuously monitored using water-perfused manometry. The time to appearance of phase III contractions (i.e., housekeeper wave) was monitored following administration of the ibuprofen tablet. Our results clearly demonstrated the dynamic change in pH as a function of time and, most significantly, the extremely low buffer capacity along the GI tract. The buffer capacity on average was 2.26 µmol/mL/ΔpH in fasted state (range: 0.26 and 6.32 µmol/mL/ΔpH) and 2.66 µmol/mL/ΔpH in fed state (range: 0.78 and 5.98 µmol/mL/ΔpH) throughout the entire upper GI tract (stomach, duodenum, and proximal and mid/distal jejunum). The implication of this very low buffer capacity of the human GI tract is profound for the oral delivery of both acidic and basic active pharmaceutical ingredients (APIs). An in vivo predictive dissolution method would require not only a bicarbonate buffer but also, more significantly, a low buffer capacity of dissolution media to reflect in vivo dissolution conditions.

Drug disposition before and after gastric bypass: fenofibrate and posaconazole.

AIMS: Roux-en-Y gastric bypass (RYGB) alters the anatomical structure of the gastrointestinal tract, which can result in alterations in drug disposition. The aim of the present study was to evaluate the oral disposition of two compounds belonging to the Biopharmaceutical Classification System Class II - fenofibrate (bile salt-dependent solubility) and posaconazole (gastric pH-dependent dissolution) - before and after RYGB in the same individuals. METHODS: A single-dose pharmacokinetic study with two model compounds - namely, 67 mg fenofibrate (Lipanthyl®) and 400 mg posaconazole (Noxafil®) - was performed in 12 volunteers pre- and post-RYGB. After oral administration, blood samples were collected at different time points up to 48 h after administration. Plasma concentrations were determined by high-performance liquid chromatography in order to calculate the area under the concentration-time curve up to 48 h (AUC0-48 h ), the peak plasma concentration (Cmax) and the time to reach peak concentration (Tmax ). RESULTS: After administration of fenofibrate, no relevant differences in AUC0-48 h , Cmax and Tmax between the pre- and postoperative setting were observed. The geometric mean of the ratio of AUC0-48 h post/pre-RYGB for fenofibrate was 1.10 [95% confidence interval (CI) 0.87, 1.40; P = 0.40]. For posaconazole, an important decrease in AUC0-48 h and Cmax following RYGB was shown; the geometric mean of the AUC0-48 h post/pre-RYGB ratio was 0.68 (95% CI 0.48, 0.96; P = 0.03) and the geometric mean of the Cmax pre/post-RYGB ratio was 0.60 (95% CI 0.39, 0.94; P = 0.03). The decreased exposure of posaconazole could be explained by the increased gastric pH and accelerated gastric emptying of fluids post-RYGB. No difference for Tmax was observed. CONCLUSIONS: The disposition of fenofibrate was not altered after RYGB, whereas the oral disposition of posaconazole was significantly decreased following RYGB.

Can in vitro/in silico tools improve colonic concentration estimations for oral extended-release formulations? A case study with upadacitinib.

Upadacitinib, classified as a highly soluble drug, is commercially marketed as RINVOQ®, a modified-release formulation incorporating hydroxypropyl methylcellulose as a matrix system to target extended release throughout the gastrointestinal (GI) tract. Our study aimed to explore how drug release will occur throughout the GI tract using a plethora of in vitro and in silico tools. We built a Physiologically-Based Pharmacokinetic (PBPK) model in GastroPlus™ to predict the systemic concentrations of the drug when administered using in vitro dissolution profiles as input to drive luminal dissolution. A series of in vitro dissolution experiments were gathered using the USP Apparatus I, III and IV in presence of biorelevant media, simulating both fasted and fed state conditions. A key outcome from the current study was to establish an in vitro-in vivo correlation (IVIVC) between (i) the dissolution profiles obtained from the USP I, III and IV methods and (ii) the fraction absorbed of drug as deconvoluted from the plasma concentration-time profile of the drug. When linking the fraction dissolved as measured in the USP IV model, a Level A IVIVC was established. Moreover, when using the different dissolution profiles as input for PBPK modeling, it was also observed that predictions for plasma Cmax and AUC were most accurate for USP IV compared to the other models (based on predicted versus observed ratios). Furthermore, the PBPK model has the utility to extract the predicted concentrations at the level of the colon which can be of utmost interest when working with specific in vitro assays.

Acute care bundles should be used for patients with intracerebral haemorrhage: An expert consensus statement.

PURPOSE: Intracerebral haemorrhage (ICH) is the most devastating form of stroke and a major cause of disability. Clinical trials of individual therapies have failed to definitively establish a specific beneficial treatment. However, clinical trials of introducing care bundles, with multiple therapies provided in parallel, appear to clearly reduce morbidity and mortality. Currently, not enough patients receive these interventions in the acute phase. METHODS: We convened an expert group to discuss best practices in ICH and to develop recommendations for bundled care that can be delivered in all settings that treat acute ICH, with a focus on European healthcare systems. FINDINGS: In this consensus paper, we argue for widespread implementation of formalised care bundles in ICH, including specific metrics for time to treatment and criteria for the consideration of neurosurgical therapy. DISCUSSION: There is an extraordinary opportunity to improve clinical care and clinical outcomes in this devastating disease. Substantial evidence already exists for a range of therapies that can and should be implemented now.

Dissolution Challenges Associated with the Surface pH of Drug Particles: Integration into Mechanistic Oral Absorption Modeling.

The present work aimed to differentiate between in vitro dissolution profiles of ibuprofen as input for GastroPlus™ and to see the impact on systemic exposure. In vitro dissolution profiles of ibuprofen obtained under low- and high-buffered dissolution media were used as input using the z-factor approach. In a second step, a customized surface pH calculator was applied to predict the surface pH of ibuprofen under these low- and high-buffered dissolution conditions. These surface pH values were adopted in GastroPlus™ and simulations were performed to predict the systemic outcome. Simulated data were compared with systemic data of ibuprofen obtained under fasted state conditions in healthy subjects. The slower dissolution rate observed when working under low-buffered conditions nicely matched with the slower dissolution rate as observed during the clinical aspiration study and was in line with the systemic exposure of the drug. Finally, a population simulation was performed to explore the impact of z-factor towards bioequivalence (BE) criteria (so-called safe space). Concerning future perspectives, the customized calculator should be developed in such a way to make it possible to predict the dissolution rate (being informed by the particle size distribution) which, in its turn, can be used as a surrogate to predict the USP2 dissolution curve. Subsequently, validation can be done by using this profile as input for PBPK platforms.

Challenges and Strategies for Solubility Measurements and Dissolution Method Development for Amorphous Solid Dispersion Formulations.

This manuscript represents the view of the Dissolution Working Group of the IQ Consortium on the challenges of and recommendations on solubility measurements and development of dissolution methods for immediate release (IR) solid oral dosage forms formulated with amorphous solid dispersions. Nowadays, numerous compounds populate the industrial pipeline as promising drug candidates yet suffer from low aqueous solubility. In the oral drug product development process, solubility along with permeability is a key determinant to assure sufficient drug absorption along the intestinal tract. Formulating the drug candidate as an amorphous solid dispersion (ASD) is one potential option to address this issue. These formulations demonstrate the rapid onset of drug dissolution and can achieve supersaturated concentrations, which poses significant challenges to appropriately characterize solubility and develop quality control dissolution methods. This review strives to categorize the different dissolution and solubility challenges for ASD associated with 3 different topics: (i) definition of solubility and sink conditions for ASD dissolution, (ii) applications and development of non-sink dissolution (according to conventional definition) for ASD formulation screening and QC method development, and (iii) the advantages and disadvantages of using dissolution in detecting crystallinity in ASD formulations. Related to these challenges, successful examples of dissolution experiments in the context of control strategies are shared and may lead as an example for scientific consensus concerning dissolution testing of ASD.

Leveraging Oral Drug Development to a Next Level: Impact of the IMI-Funded OrBiTo Project on Patient Healthcare.

A thorough understanding of the behavior of drug formulations in the human gastrointestinal (GI) tract is essential when working in the field of oral drug development in a pharmaceutical company. For orally administered drug products, various GI processes, including disintegration of the drug formulation, drugrelease, dissolution, precipitation, degradation, dosage form transit and permeation, dictate absorption into the systemic circulation. These processes are not always fully captured in predictive in vitro and in silico tools, as commonly applied in the pre-clinical stage of formulation drug development. A collaborative initiative focused on the science of oral biopharmaceutics was established in 2012 between academic institutions and industrial companies to innovate, optimize and validate these in vitro and in silico biopharmaceutical tools. From that perspective, the predictive power of these models can be revised and, if necessary, optimized to improve the accuracy toward predictions of the in vivo performance of orally administered drug products in patients. The IMI/EFPIA-funded "Oral Bioavailability Tools (OrBiTo)" project aimed to improve our fundamental understanding of the GI absorption process. The gathered information was integrated into the development of new (or already existing) laboratory tests and computer-based methods in order to deliver more accurate predictions of drug product behavior in a real-life setting. These methods were validated with the use of industrial data. Crucially, the ultimate goal of the project was to set up a scientific framework (i.e., decision trees) to guide the use of these new tools in drug development. The project aimed to facilitate and accelerate the formulation development process and to significantly reduce the need for animal experiments in this area as well as for human clinical studies in the future. With respect to the positive outcome for patients, high-quality oral medicines will be developed where the required dose is well-calculated and consistently provides an optimal clinical effect. In a first step, this manuscript summarizes the setup of the project and how data were collected across the different work packages. In a second step, case studies of how this project contributed to improved knowledge of oral drug delivery which can be used to develop improved products for patients will be illustrated.