Height difference between the vestibular and palatal walls and palatal width: a cone beam computed tomography approach.

BACKGROUND: The objective of this study was to measure two parameters involved in tri-dimensional implant planning: the position of the buccal and palatal bone wall and the palatal thickness. METHODS: Cone beam computed tomography (CBCT) images (Planmeca ProMax 3D) of 403 teeth (208 upper teeth and 195 lower teeth) were obtained from 49 patients referred to the Dental School of Seville from January to December 2014. The height difference between the palatal and buccal walls was measured on the most coronal point of both walls. The thickness of the palatal wall was measured 2 mm from the most coronal point of the palatal wall. RESULTS: The mean values in the maxilla were 1.7 ± 0.9 mm for central and lateral incisors, 2.2 ± 1.7 mm for canines, 1.6 ± 0.9 mm for premolars and 1.9 ± 1.5 mm for molars. In the lower jaw, the mean values were 1.3 ± 0.8 mm for incisors, 1.7 ± 1.2 mm for canines, 2.3 ± 1.3 mm for premolars, and 2.6 ± 1.7 mm for molars. In the upper jaw, more than 55% of maxillary teeth (excluding second premolars and molars) presented mean height differences greater than 1 mm. In the mandible, more than 60% of incisors showed a buccal bone thickness of 1 mm from the apical to lingual aspect. All teeth except the second premolar presented a buccal wall located more than 1 mm more apically than the lingual bone wall. CONCLUSIONS: The buccal bone wall is located more apically (greater than 1 mm) than the palatal or lingual table in most of the cases assessed. The thickness of the palatal or lingual table is also less than 2 mm in the maxilla and mandible, except in the upper canines and premolars and the lower molars.

Crestal module design optimization of dental implants: finite element analysis and in vivo studies.

The aim of this study was to evaluate the biomechanical behavior of Bone Level dental implants with four different neck designs in contact with cortical bone. Numerical simulations were performed using a Finite Element Method (FEM) based-model. In order to verify the FEM model, the in silico results were compared with the results obtained from histological analysis performed in an in vivo study with New Zealand rabbits. FEM was performed using a computerized 3D model of Bone Level dental implants inserted in the lower jaw bone with an applied axial load of 100 N. The analysis was performed using four different implant neck designs: even surfaced, screwed, three-ring design and four-ring design. Interface are of bone growth was evaluated by analyzing the Bone-Implant-Contact (BIC) parameter obtained from in vivo histological process and analyzed by Scanning Electron Microscopy (SEM). Bone Level implants were inserted in the rabbit tibia, placing two implants per tibia. The BIC was evaluated after three and six weeks of implantation. FEM studies showed that the three-ring design presented lower values of stress distribution compared to the other studied designs. The lower levels of mechanical stress were then correlated with the in vivo studies, showing that the three-ring design presented the highest BIC value after 3 and 6 weeks of implantation. In silico and in vivo results both concluded that the implants with three-ring neck design presented the best biomechanical and histological behavior in terms of new bone formation, enhanced mechanical stability and optimum osseointegration.

Repeatability of the resonance frequency analysis values in implants with a new technology.

BACKGROUND: Assess the reliability (by means of reproducibility and repeatability) of the PenguinRFA system, analyse the ISQ values of different implant types and correlate the ISQ with the insertion torque during the placement of the implant. MATERIAL AND METHODS: 120 rough surface implants were placed in bovine bone (type II and III). The implants were divided into groups, according to its design. Once the implants were in place, the exact insertion torque was registered. Then, primary stability was measured by means of the resonance frequency analysis with the PenguinRFA and the Osstell ISQ devices. In each implant two transducers of each device were used. Three measurements were obtained with each transducer. RESULTS: The mean ISQ (implant stability quotient) of the whole sample is 67,70 ± 5,51. The Intraclass Correlation Coefficient (ICC) is 0,933 and 0,944 for transducers 1 and 2 respectively. The reproducibility is 0,906. The mean insertion torque is 24,54 ± 8,96N. The correlation between the ISQ and the insertion torque is 0,507 p<0,000 (MultiPeg 1) and 0,468 p<0,000 (MultiPeg 2) for bone type II and 0,533 p<0,801 (MultiPeg 1) and 0,193 p<0,140 (MultiPeg 2) for bone type III. CONCLUSIONS: The results of the present trial suggest that the PenguinRFA presents excellent reproducibility and repeatability, so it could be very useful in the monitoring of the stability of implants over time. Additionally, according to the results, the correlation between the IT and the RFA is low and there are no statistically significant differences in between implant types.

Unravelling the effect of macro and microscopic design of dental implants on osseointegration: a randomised clinical study in minipigs.

Several dental implants are commercially available and new prototype design are constantly being fabricated. Nevertheless, it is still unclear what parameters of the design affect most the osseointegration of dental implants. The purpose of this study is to assess the effects of the microscopic and macroscopic design of dental implants in the osseointegration by comparing three macroscopic designs (Straumann tissue level (STD), essential cone (ECD) and prototype design (PD)) and six surface treatments. A total of 96 implants were placed in 12 minipigs. The implant stability quotient (ISQ), was assessed at the time of implantation, as well as at 2, 4 and 8 weeks. Histomorphometric and statistical analyses were conducted at the different sacrifice times, being 2, 4 and 8 weeks, to analyse the bone to implant contact (BIC), the bone area density (BAT) and the density of bone outside the thread region (ROI). The macroscopic design results showed higher ISQ values for the ECD, whereas the histomorphometric analysis showed higher ossoeintegration values for the STD. Regarding the microscopic design, both Sandblasted plus acid etching (hydrochloric/sulphuric acid) in a nitrogen atmosphere (SLActive) and Shot-blasted or bombarded with alumina particles and posterior alkaline immersion and thermal treatment (ContacTi) showed superior results in terms of osseointegration and reduced the osseointegration times from 8 weeks to 4 weeks compared to the other analysed surfaces. In conclusion, each of the macroscopic and microscopic designs need to be taken into account when designing novel dental implants to enhance the osseointegration process.

Thickness of the buccal bone wall and root angulation in the maxilla and mandible: an approach to cone beam computed tomography.

BACKGROUND: The objective of this paper is to anatomically describe the bone morphology in the maxillary and mandibular tooth areas, which might help in planning post-extraction implants. METHODS: CBCT images (Planmeca ProMax 3D) of 403 teeth (208 upper teeth and 195 lower teeth) were obtained from 49 patients referred to the Dental School of Seville from January to December 2014. The thickness of the facial wall was measured at the crest, point A, 4 mm below, point B, and at the apex, point C. The second parameter was the angle formed between the dental axis and the axis of the basal bone. RESULTS: A total of 403 teeth were measured. In the maxilla, 89.4% of incisors, 93.94% of canines, 78% of premolars and 70.5% of molars had a buccal bone wall thickness less than the ideal 2 mm. In the mandible, 73.5% of incisors, 49% of canines, 64% of premolars and 53% of molars had < 1 mm buccal bone thickness as measured at point B. The mean angulation in the maxilla was 11.67 ± 6.37° for incisors, 16.88 ± 7.93° for canines, 13.93 ± 8.6° for premolars, and 9.89 ± 4.8° for molars. In the mandible, the mean values were 10.63 ± 8.76° for incisors, 10.98 ± 7.36° for canines, 10.54 ± 5.82° for premolars and 16.19 ± 11.22° for molars. CONCLUSIONS: The high incidence of a buccal wall thickness of less than 2 mm in over 80% of the assessed sites indicates the need for additional regeneration procedures, and several locations may also require custom abutments to solve the angulation problems for screw-retained crowns.

Implant-abutment connections: influence of the design on the microgap and their fatigue and fracture behavior of dental implants.

Microgap between implant and abutment can produce biological and mechanical problems such as peri-implantitis and/or fatigue failures. The aim of this study was to evaluate microgap size and fatigue behavior of external and internal connections. In both systems the torque to tighten the abutment screw of single crown abutments was 45 Ncm. Fifty implants for each connection type were studied. One subgroup (n = 5) was used by the observation and evaluation of the microgap, other (n = 5) was tested for fracture strength and the other (n = 40) was subjected to dynamic loading. The internal connection presents a lower microgap than the external ones. From fatigue results, the external hexagon interface showed superior result compared to the internal hexagon interfaces. The tolerances in the internal connections are better and favour the fatigue behavior but this factor alone is not sufficient to improve the fatigue response in relation to the external connections when the screw is subjected at the same torque. The external system presents a higher value of the area than the internal and it produces a better load distribution. Microgaps and mechanical properties are very important for the long-term behavior of the dental implants and these aspects should be known by the implantologists.

Comparative analysis of 2 resonance frequency measurement devices: Osstell Mentor and Osstell ISQ.

OBJECTIVE: Comparing reliability of Osstell Mentor and Osstell ISQ in implant stability measurement, and assessing whether their measurements are comparable. MATERIALS AND METHOD: Implant stability was measured with both devices on 58 implants in 15 patients. Six measurements were completed with each device with 2 different transducers (3 measurements with each transducer), that is, 12 measurements for each implant. RESULTS: Mean implant stability quotient (ISQ) value with Osstell ISQ was 72.59, 72.47, and 73.17 in the first measurements, respectively. With Osstell Mentor, the results were 72.43, 72.60, and 73.26, respectively; mean ranges were 3.37, 3.60, and 3.75, respectively. However, mean value with Osstell ISQ and Osstell Mentor was 72.87 and 72.04, respectively. The intraclass correlation coefficient was 0.98. This means an almost perfect degree of concordance between both devices. CONCLUSIONS: Resonance frequency analysis systems in Osstell Mentor and Osstell ISQ show almost perfect reproducibility and repeatability.

Influence of acid-etching after grit-blasted on osseointegration of titanium dental implants: in vitro and in vivo studies.

Rough implant surfaces have shown improved osseointegration rates. In a majority of dental implants, the microrough surfaces are obtained by grit blasting and/or acid-etching. The aim of this contribution was to evaluate the effects of acid-etching, after the grit-blasted treatment in titanium dental implants, on surface wettability, surface energy, osteoblast responses and its osseointegration behavior. Four surfaces were studied: as-machined, acid-etched, micro-rough by grit-blasting and the combination grit-blasted surface with acid-etched. The surfaces with increasing roughness show more osteoblastic adhered cells. This effect was most pronounced on samples blasted and blasted with acid-etching. The roughness obtained by grit-blasting is the main factor in comparison with the acid etching treatment in the biological response. These results were confirmed in vivo tests and histological analysis. The results demonstrated that the combination of the grit-blasted and acid-etched accelerated lightly bone regeneration at the different periods of implantation in comparison with the grit-blasted implants.

Fatigue of Narrow Dental Implants: Influence of the Hardening Method.

The use of narrow titanium dental implants (NDI) for small ridges, reduced interdental space, or missing lateral incisors can be a viable option when compared to the conventional wider dental implants. Furthermore, in many cases, standard diameter implant placement may not be possible without grafting procedures, which increases the healing time, cost, and morbidity. The aim of this study was to analyze the mechanical viability of the current narrow implants and how narrow implants can be improved. Different commercially available implants (n = 150) were tested to determine maximum strength, strain to fracture, microhardness, residual stress, and fatigue obtaining the stress-number of cycles to fracture (SN) curve. Fractography was studied by scanning electron microscopy. The results showed that when the titanium was hardened by the addition of 15% of Zr or 12% cold worked, the fatigue limit was higher than the commercially pure grade 4 Ti without hardening treatment. Grade 4 titanium without hardening treatment in narrow dental implants can present fractures by fatigue. These narrow implants are subjected to high mechanical stresses and the mechanical properties of titanium do not meet the minimal requirements, which lead to frequent fractures. New hardening treatments allow for the mechanical limitations of conventional narrow implants to be overcome in dynamic conditions. These hardening treatments allow for the design of narrow dental implants with enhanced fatigue life and long-term behavior.

Relevant Design Aspects to Improve the Stability of Titanium Dental Implants.

Post-extractional implants and immediate loading protocols are becoming much more frequent in everyday clinical practice. Given the existing literature about tapered implants, the objective of this paper was to understand whether implant shape had a direct influence on the results of the insertion torque (IT) and implant stability quotient (ISQ). Seven tapered implant prototypes were developed and distributed into three groups and compared with a control cylindrical implant-VEGA by Klockner Implant System. The implants were inserted into bovine bone type III according to Lekholm and Zarb Classification. The sample size was n = 30 for the three groups. Final IT was measured with a torquemeter, and the ISQ was measured with Penguin Resonance Frequency Analysis (RFA). Modifications done to the Prototype I did not reveal higher values of the ISQ and IT when compared to VEGA. In the second group, when comparing the five prototypes (II-VI) with VEGA, it was seen that the values of the ISQ and IT were not always higher, but there were two values of the ISQ that were statistically significantly higher with the 4.0 mm diameter Prototypes II (76.3 ± 6.1) and IV (78 ± 3.7). Prototype VII was the one with higher and significant values of the ISQ and IT. In both diameters and in both variables, all differences were statistically significant enough to achieve the higher values of primary stability values (IT and ISQ). Given the limitations of this study, it can be concluded that when there is an increase of the diameter of the implant and body taper, there is an increase of the ISQ and IT, showing that the diameter of the implant is an important criteria to obtain higher values of primary stability.

Espacio biológico. Parte I: La inserción diente-encía / Biology Space. Part I: The insertion dentogingival

Se denomina espacio biológico a la unión dentogingival, que está constituida por el epitelio de unión y el tejido conectivo de inserción de la encía. Cuando se habla de espacio biológico no sólo se debe pensar en la longitud de la inserción gingival, sino que se debe relacionar con el grosor de la encía, el biotipo periodontal y la profundidad del surco gingival, puesto que todos estos parámetros se integran, y deben ser tenidos en cuenta para comprender de manera exacta la morfología del tejido gingival supracrestal. La variabilidad de dimensiones de los componentes epitelial y conectivo que existe entre individuos, e incluso dentro del mismo individuo, es otro factor que debe ser considerado. Una vez que se ha invadido la unión dentogingival, el tipo de manifestación clínica que se produce va a ser distinta según los casos, ya que no hay que olvidar que la respuesta está relacionada con la susceptibilidad del paciente frente a la enfermedad periodontal, además de otros factores que se enumerarán. Y cuando se ha invadido el espacio biológica con sintomatología, ¿qué se puede hacer? La parte final esbozará las opciones terapéuticas disponibles frente a estas situaciones (AU)

Biological width is known as the dentogingival unit formed by the junction of the epithelium and the connective tissue attachement. Biological width does not only refer to the length of the gingival insertion, but also to the gingival thickness, the type of periodontal tissues and the depth of the gingival sulcus, because all these components are part of a unit and should be considered as such. Another factor to be considered is the dimensional range of the epithelial and connective tissue components between individuals and in a given individual. Once the dentogingival unit is invaded, different clinical processes can take place regarding the host response to periodontal disease among other different factors that we will expose. In the event that the biological width has been invaded, and symptoms have appeared, what can be done? At the end and in a nutshell, the reader will find a brief introduction to the different treatment options available for these patients (AU)