Evaluation of Electromagnetic Fields in a Hospital for Safe Use of Electronic Medical Equipment.

Establishment of electromagnetic compatibility is important in use of electronic medical equipment in hospitals. To evaluate the electromagnetic environment, the electric field intensity induced by electromagnetic radiation in broadcasting spectra coming from outside the hospital was measured in a new hospital building before any patients visited the hospital and 6 months after the opening of the hospital. Various incoming radio waves were detected on the upper floors, with no significant difference in measured levels before and after opening of the hospital. There were no cellphone terminal signals before the hospital opened, but these signals were strongly detected at 6 months thereafter. Cellphone base stations signals were strongly detected on the upper floors, but there were no signals at most locations in the basement and in the center of the building on the lower floors. A maximum electrical intensity of 0.28 V/m from cellphone base stations (2.1 GHz) was detected at the south end of the 2nd floor before the hospital opened. This value is lower than the EMC marginal value for general electronic medical equipment specified in IEC 60601-1-2 (3 V/m). Therefore, electromagnetic interference with electronic medical equipment is unlikely in this situation. However, cellphone terminal signals were frequently detected in non-base station signal areas. This is a concern, and understanding signal strength from cellphone base stations at a hospital is important for promotion of greater safety.

Effects of increased surface coverage of polyvinylpyrrolidone over a polysulfone hemofilter membrane on permeability and cell adhesion during continuous hemofiltration.

The purpose of the present study was to evaluate the adhesiveness of blood cells and the solute removal performance change of modified polysulfone membranes which have increased polyvinylpyrrolidone (PVP) coverage over their surface. Continuous hemofiltration (CHF) experiments for 24 h were carried out using an ex vivo hemofilter evaluation system to compare a modified polysulfone hemofilter (SHG) with the conventional polysulfone hemofilter (SH). The 25 and 50 % cutoff values of the sieving coefficient of dextran after CHF and the protein concentration in the filtrate was higher in SHG, indicating that less fouling occurred in the SHG membrane. Adhesion of blood cells after 24 h of CHF was significantly higher in the case of SH than in the case of SHG. Blood cell adhesion and membrane fouling were reduced with the use of a polysulfone membrane modified with increased PVP coverage over the surface.

Electromagnetic interference of implantable cardiac devices from a shoulder massage machine.

Shoulder massage machines have two pads that are driven by solenoid coils to perform a per cussive massage on the shoulders. There have been concerns that such machines might create electromagnetic interference (EMI) in implantable cardiac devices because of the time-varying magnetic fields produced by the alternating current in the solenoid coils. The objective of this study was to investigate the potential EMI from one such shoulder massage machine on implantable cardiac devices. We measured the distribution profile of the magnetic field intensity around the massage machine. Furthermore, we performed an inhibition test and an asynchronous test on an implantable cardiac pacemaker using the standardized Irnich human body model. We examined the events on an implantable cardioverter-defibrillator (ICD) using a pacemaker programmer while the massage machine was in operation. The magnetic field distribution profile exhibited a peak intensity of 212 (A/m) in one of the solenoid coils. The maximal interference distance between the massage machine and the implantable cardiac pacemaker was 28 cm. Ventricular fibrillation was induced when the massage machine was brought near the electrode of the ICD and touched the Irnich human body model. It is necessary to provide a "don't use" warning on the box or the exterior of the massage machines or in the user manuals and to caution patients with implanted pacemakers about the dangers and appropriate usage of massage machines.

Breathing nitric oxide plus hydrogen gas reduces ischemia-reperfusion injury and nitrotyrosine production in murine heart.

Inhaled nitric oxide (NO) has been reported to decrease the infarct size in cardiac ischemia-reperfusion (I/R) injury. However, reactive nitrogen species (RNS) produced by NO cause myocardial dysfunction and injury. Because H2 is reported to eliminate peroxynitrite, it was expected to reduce the adverse effects of NO. In mice, left anterior descending coronary artery ligation for 60 min followed by reperfusion was performed with inhaled NO [80 parts per million (ppm)], H2 (2%), or NO + H2, starting 5 min before reperfusion for 35 min. After 24 h, left ventricular function, infarct size, and area at risk (AAR) were assessed. Oxidative stress associated with reactive oxygen species (ROS) was evaluated by staining for 8-hydroxy-2'-deoxyguanosine and 4-hydroxy-2-nonenal, that associated with RNS by staining for nitrotyrosine, and neutrophil infiltration by staining for granulocyte receptor-1. The infarct size/AAR decreased with breathing NO or H2 alone. NO inhalation plus H2 reduced the infarct size/AAR, with significant interaction between the two, reducing ROS and neutrophil infiltration, and improved the cardiac function to normal levels. Although nitrotyrosine staining was prominent after NO inhalation alone, it was eliminated after breathing a mixture of H2 with NO. Preconditioning with NO significantly reduced the infarct size/AAR, but not preconditioning with H2. In conclusion, breathing NO + H2 during I/R reduced the infarct size and maintained cardiac function, and reduced the generation of myocardial nitrotyrosine associated with NO inhalation. Administration of NO + H2 gases for inhalation may be useful for planned coronary interventions or for the treatment of I/R injury.

Activation of platelets upon contact with a vitamin E-coated/non-coated surface.

The purpose of this study was to determine the effects of a vitamin E-coated surface on platelet activation, focusing on the interactions among the vitamin E-coated surface, platelets and leukocytes. Platelet-rich plasma (PRP) or PRP containing leukocytes (LPRP) was used. No difference was observed in platelet activation between PRP and LPRP for a vitamin E-coated membrane, meaning that platelet activation triggered by leukocytes was suppressed in plasma coming in contact with a vitamin E-coated membrane, while the membrane itself directly induced platelet activation. The antioxidant capacity of the vitamin E-coated membrane in contact with PRP or LPRP was partially reduced, but sufficient residual capacity remained. The in vitro experiments using an oxidized vitamin E-coated surface revealed that P-selectin expression and superoxide anion production in the platelets and platelet adhesion were induced by contact with the oxidized vitamin E-coated surface. We conclude that contact with a vitamin E-coated surface reduces platelet activation mediated by superoxide anions, probably by reducing superoxide anions, but during the process of the reduction, the vitamin E-coated surface itself becomes oxidized, which again causes platelet activation. The beneficial effects of a vitamin E-coated dialyzer in respect of platelet activation were counteracted by the formation of oxidized vitamin E.

X-ray radiation causes electromagnetic interference in implantable cardiac pacemakers.

BACKGROUND: X-rays are not thought to cause electromagnetic interference (EMI) in implantable cardiac pacemakers. However, x-ray radiation during computed tomography (CT) scanning has been reported to cause EMI in some implantable cardiac pacemakers. The objectives of this study were to identify the location within the pacemakers where x-ray radiation causes EMI and to investigate the association of EMI with the x-ray radiation conditions. METHODS: We verified the location where x-ray radiation caused EMI using a CT scanner and conventional radiographic x-ray equipment. An inhibition test and an asynchronous test were performed using five types of implantable cardiac pacemakers. RESULTS: X-ray radiation inhibited the pacing pulses of four types of implantable cardiac pacemakers when the body of each implantable cardiac pacemaker, containing a complementary metal-oxide semiconductor (CMOS), was scanned using a CT scanner. We confirmed that x-ray-induced EMI depends on the x-ray radiation conditions, that is, the tube voltage, tube current, x-ray dose, and direction of x-ray radiation, as well as the sensing thresholds of the implantable cardiac pacemakers. CONCLUSIONS: X-ray radiation caused EMI in some implantable cardiac pacemakers, probably because the CMOS component was irradiated. The occurrence of EMI depended on the pacemaker model, sensing threshold of the pacemaker, and x-ray radiation conditions.

Macrophages that survive hyperoxia exposure have higher superoxide dismutase activities in their mitochondria.

Prolonged exposure to hyperoxia, which is routinely used in patients with severe respiratory failure, leads to the generation of excessive reactive oxygen species, resulting in lung injury. In the present study, we focused on macrophages and their survival, superoxide dismutase (SOD) activity in mitochondria (Mn-SOD activity), and mitochondrial DNA (mtDNA) mutation after exposure to hyperoxia. Macrophages were cultured under two different conditions: normoxia and intermittent hyperoxia. The number of cells exposed to intermittent hyperoxia for 3 weeks significantly decreased, compared with the number of cells exposed to normoxia. The Mn-SOD activity of the cells that survived intermittent hyperoxia exposure was significantly higher than that of the cells exposed to normoxia. Direct sequencing and a PCR-RFLP assay did not provide any evidence of mutation in the cells that survived intermittent hyperoxia exposure. In conclusion, an increase in the antioxidative activity of mitochondria is important for the survival of macrophages exposed to hyperoxia, and the increased activity level possibly enhances protective effects against mtDNA mutations in surviving cells.

Synchronization between cardiac and respiratory rhythms in healthy subjects and patients.

Synchronization between cardiac and respiratory rhythms may be important for oxygen transport to tissues. The aim of this study was to investigate the synchronization between cardiac and respiratory rhythms. We evaluated the rhythms in 12 healthy males and 24 patients. The incidence rates of heart beats were obtained in each time interval relative to the initiation time point of inspiration. A simple index of timing variability of heart beats was defined. When the variability is large, the link between cardiac and respiratory rhythms was considered to be strong. The variability value of patients with disorder in the autonomic nervous system was larger than that of healthy subjects (p < 0.05). The variability of patients on controlled ventilation was lower than that of healthy subjects (p < 0.01), whereas the value on cardiac pacemaker did not differ from healthy subjects. In conclusion, the synchronization between cardiac and respiratory rhythms was confirmed, and it is suggested that the synchronization is enhanced when feed-back signals from respiratory movement to respiratory center were decreased.

Study of light transmission through gauze pad effected by blood or liquids to detect needle dislodgement.

OBJECTIVE: Serious accidents during hemodialysis such as a large amount of blood loss are often caused by venous needle dislodgement. To develop a bleeding sensor based on a photo sensor for monitoring the needle sites, we studied effects of liquids and porcine blood on light transmission through a thin gauze pad with a basic photo sensor. METHODS: The photo sensor consisted of an ordinary electrical circuit, a light emitting diode (LED, lambda max = 645 nm), a photo diode (PD), and a thin gauze pad placed between the LED and PD that were tightly attached to the edges of a plastic clip. The light transmitted through the gauze pad, soaked with liquids or porcine blood dropped on it, was measured with a digital voltmeter. The liquids were reverse osmosis water, physiological saline, glucose in water at 5, 10, 20, 40 and 50%, porcine plasma, and porcine blood (Hct 40, 30 and 20%). RESULTS: The liquids on a tight-weave gauze pad, significantly increased the voltage (light transmission) from 0.412 +/- 0.003 V (SD) to 0.794 +/- 0.025 V (minimum, by reverse osmosis water) and to 0.945 +/- 0.011 V (maximum, by 50% glucose). The porcine blood significantly decreased the voltage from 0.412 to 0.195 +/- 0.030 V in Hct 40%, to 0.334 +/- 0.035 in Hct 30%, to 0.397 +/- 0.007 V in Hct 20%. The higher the concentration of glucose, the more the light transmission increased. The higher concentration of Hct, the more the light transmission decreased. Similar results were also shown for the loose-weave pad. CONCLUSIONS: Using two types of gauze pads, we confirmed that liquids significantly increased light transmission through gauze pad, but porcine blood decreased light transmission. This opposite response can be used to distinguish liquids from blood on a gauze pad.

The role of nitric oxide in reducing deformability of Lewis lung tumor cell stimulated by inflammatory cytokines.

Highly metastatic cells, especially in the lungs, are known to be resistant to nitric oxide (NO)-mediated cytotoxicity, compared with poorly or non-metastatic cells. However, the precise mechanisms connecting NO and metastasis remain to be determined. To clarify the role of NO in the characteristic changes in NO-resistant cells in response to inflammatory cytokines, we used Lewis lung tumor (LLT) cells, which are known to be highly metastatic NO-resistant cells, and determined the changes in cell deformability and the gene expression profile after the cells were stimulated using cytokine mixture or an NO donor. Both exogenous NO and endogenous NO via inducible NO synthase produced by cytokines decreased cell deformability by enhancing actin polymerization. The expression of several genes associated with actin polymerization was changed so as to increase actin filaments in the cells by enhancing actin polymerization and by suppressing actin depolymerization, actin filament severing, and barbed-end actin filament capping. In conclusion, inflammatory cytokine stimulation reduces deformability of LLT cells and enhances actin polymerization which is mainly controlled by the same genes induced by NO.

Bench study of auto-CPAP devices using a collapsible upper airway model with upstream resistance.

The aim of this study was to investigate the response of auto-CPAP devices to respiratory events (apnea, hypopnea, flow-limitation and snoring) on the same condition using a physiological upper airway model. The hypothesis of this study is that collapsibility of the flow-limiting collapsible segment of the airway is influenced by the upstream airway resistance. Five auto-CPAP devices, AutoSet T, AutoSet Spirit, Goodnight 420E, PV10i and REMstar Auto were evaluated. Apnea: all the devices increased the auto-CPAP level, while AutoSet T and AutoSet Spirit did not respond to apnea for 30s. Hypopnea: all the devices except the AutoSet T and Goodnight 420E increased pressure. Flow-limitation: all the devices except the PV10i and REMstar Auto increased pressure. Snoring: the snoring sounds disappeared when REMstar Auto and PV10i were used, and the Goodnight 420E lowered the level of snoring. In conclusion, the response of auto-CPAP devices to respiratory events differed. Collapsible upper airway model with upstream resistance is useful for the first-step assessment of auto-CPAP devices.

[Verification of irradiation conditions of X-rays that influence implantable cardiac pacemakers].

Originally, it was thought that X-rays did not influence implantable cardiac pacemakers. In general, radiological technologists did not take proper care of these devises at the time of X-Ray examinations. However, 11 cases in which pacemakers malfunctioned (for example partial electrical reset) during CT examinations have been reported in recent years. At the time, we tended to attribute such problems to the peculiarities of multi-detector CT (MDCT). However, on logical grounds this explanation seemed weak. To better explain the problem, we attempted various tests in which pacemakers were exposed to CT and X-ray photography equipment. We analyzed some ECG results to clarify the matter and took measurements to examine these problems.

Simulation system of arrhythmia using ActiveX control.

A simulation system for arrhythmias has been developed using Windows-based software technology, ActiveX control. The cardiac module consists of six cells, the sinus, atrium, AV node, ventricle, and ectopic foci. The physiological properties of the cells, the automaticity and conduction delay, were modelled, respectively, by the phase response curve and the excitability recovery curve. Cell functions were implemented in the ActiveX control and incorporated into the cardiac module. The system draws the ECG sequence as a ladder diagram in real time. The system interactively shows diverse arrhythmias for various user settings of the cell function and bidirectional conduction between the cells. Users are able to experiment virtually by setting up a so-called electrophysiological stimulation. This system is useful for learning and for teaching the interaction between the cells and arrhythmias.

Analysis of medical equipment management in relation to the mandatory medical equipment safety manager (MESM) in Japan.

Half a decade has passed since the fifth revision of the medical law and mandatory appointment of a medical equipment safety manager (MESM) in hospitals in Japan. During this period, circumstances have changed regarding maintenance of medical equipment (ME). We conducted a survey to examine these changes and the current situation in ME management. Maintenance of ME and related work were found to have increased in many hospitals, but the number of clinical engineering technologists (CETs) has only slightly increased. The appointed MESM was a CET or physician in most hospitals. In hospitals where physicians were appointed as the MESM, 81% had operation managers. Many respondents commented that it was difficult for one person to cover all the tasks required by the MESM, due to a lack of knowledge, too much work, or other reasons. This suggests the importance of an operation manager for ME to work under the MESM.

Hypoxia enhances the induction of human amniotic mesenchymal side population cells into vascular endothelial lineage.

Human amniotic mesenchymal side population (hAM-SP) cells have pluripotency and weak immunogenicity, and have promising roles in the field GAPDH of regenerative medicine. The aim of the present study was to determine whether hypoxic conditions induce the differentiation of hAM-SP cells into the vascular endothelial lineage. Mesenchymal cells were isolated from enzyme-treated amniotic membranes and stained with Hoechst 33342. The hAM-SP cells were negatively sorted by FACS and cultured in induction medium containing vascular endothelial growth factor (VEGF) under normoxic (20% O2) or hypoxic (1% O2) conditions for 1 or 2 weeks. The expression of endothelial markers such as kinase domain region (KDR), fms-like tyrosine kinase (Flt)-1, von Willebrand factor (vWF), vascular endothelial (VE)-cadherin and human vascular cell adhesion molecule (VCAM) at the gene and protein level was evaluated by real-time PCR and fluorescent immunostaining, respectively. The gene expression of KDR, Flt-1, VE-cadherin and vWF peaked after 2 weeks of culture. The protein expression of KDR and VE-cadherin was also enhanced after 2 weeks of culture under hypoxic conditions. To confirm the involvement of hypoxia-inducible factor (HIF) in the induction under hypoxic conditions, the expression of genes which are known to be upregulated by HIF was analyzed by DNA microarray. The expression of these genes increased under hypoxic conditions. hAM-SP cells cultured under hypoxic conditions differentiated into the vascular endothelial lineage, probably due to upregulation of the gene expression associated with angiogenesis through activation of the HIF system.

Study of electrical power facilities and measures for planned outages in Japanese hemodialysis clinics after the Great East Japan Earthquake.

The Great East Japan Earthquake on 11 March 2011 caused major damage in northeastern Japan. The Kanto region experienced a massive electrical power shortage in the summer of 2011. A questionnaire was submitted to 354 hemodialysis clinics in Kanagawa prefecture and the Tokyo metropolitan area, excluding isolated islands, and 176 responses were analyzed (49.7%). The questions included evaluation of the availability of a private electricity generator, countermeasures in case of a planned outage, awareness of saving electricity, and improvement of safety of medical devices or electrical facilities after the earthquake. Only 12% of the clinics had private electricity generators and many clinics had no plans to introduce this facility. However, 96% of the clinics had established countermeasures to deal with a planned outage. Many clinics planned to provide dialysis on a different day or at a different time. All clinics had tried hard to establish procedures to save electricity in the summer of 2011, and 84% of the clinics had reconsidered and improved the safety of medical devices or electricity facilities after the earthquake. These results show that the awareness of crisis management was greatly improved in the wake of the earthquake.

Prevalence of topoisomerase I genetic mutations and UGT1A1 polymorphisms associated with irinotecan in individuals of Asian descent.

Topoisomerase I (TOP-I) mutations have been shown to be correlated to irinotecan resistance in vitro. However, the prevalence of TOP-I germline mutations has yet to be systematically elucidated. On the other hand, polymorphisms of UGT1A1 have been shown to be associated with CPT-11 toxicity in clinical situations. The primary aim of this study was to investigate the prevalence of mutations in the TOP-I exons associated with CPT-11 resistance, including untreated cancer tissue. A secondary aim was to confirm the less frequent UGT1A1*28 and more frequent UGT1A1*6 in individuals of Asian descent compared to Caucasians and individuals of African descent. The prevalence of 5 reported TOP-I mutations in exons was investigated in volunteers (n=236) using DNA sequencing of the PCR products. The prevalence of TOP-I mutations in untreated lung cancer tissues (n=16) was also investigated. Additionally, 3 UGT1A1 polymorphisms, UGT1A1*6, *27 and *28, were investigated in volunteers (n=126). There were no mutations of TOP-I in any of the 236 subjects or in the untreated lung tissues. Among 128 subjects, the distribution of homozygous polymorphisms of UGT1A1 was: UGT1A1*28 in 3 (2.4%) and UGT1A1*6 in 4 (3.2%) subjects, and co-occurrence of heterozygous polymorphisms for both UGT1A1*6 and UGT1A1*28 in 4 (3.2%) subjects, and for UGT1A1*27 and UGT1A1*28 in 1 subject (0.8%). The Hardy-Weinberg deviation test showed there was no significant deviation from the equilibrium, and the association analysis indicated no significant linkage between UGT1A1*6 and UGT1A1*28. In conclusion, TOP-I genetic mutations correlated to CPT-11 resistance were not detected in any of the subjects and untreated lung cancer tissues. Less frequent UGT1A1*28 and more frequent UGT1A1*6 were confirmed in East Asian individuals compared to Caucasians and individuals of African descent. Linkage disequilibrium was not detected between UGT1A1*6 and UGT1A1*28.

Development of an alarm sound database and simulator.

OBJECTIVES: The purpose of this study was to develop an interactive software package of alarm sounds to present, recognize and share problems about alarm sounds among medical staff and medical manufactures. METHODS: The alarm sounds were recorded in variable alarm conditions in a WAV file. The alarm conditions were arbitrarily induced by modifying attachments of various medical devices. The software package that integrated an alarm sound database and simulator was used to assess the ability to identify the monitor that sounded the alarm for the medical staff. RESULTS: Eighty alarm sound files (40MB in total) were recorded from 41 medical devices made by 28 companies. There were three pairs of similar alarm sounds that could not easily be distinguished, two alarm sounds which had a different priority, either low or high. The alarm sound database was created in an Excel file (ASDB.xls 170 kB, 40 MB with photos), and included a list of file names that were hyperlinked to alarm sound files. An alarm sound simulator (AlmSS) was constructed with two modules for simultaneously playing alarm sound files and for designing new alarm sounds. The AlmSS was used in the assessing procedure to determine whether 19 clinical engineers could identify 13 alarm sounds only by their distinctive sounds. They were asked to choose from a list of devices and to rate the priority of each alarm. The overall correct identification rate of the alarm sounds was 48%, and six characteristic alarm sounds were correctly recognized by beetween 63% to 100% of the subjects. The overall recognition rate of the alarm sound priority was only 27%. CONCLUSIONS: We have developed an interactive software package of alarm sounds by integrating the database and the alarm sound simulator (URL: http://info.ahs.kitasato-u.ac.jp/tkweb/alarm/asdb.html ). The AlmSS was useful for replaying multiple alarm sounds simultaneously and designing new alarm sounds interactively.

Electromagnetic interference of implantable unipolar cardiac pacemakers by an induction oven.

Induction ovens have been reported to exert electromagnetic interference on implanted cardiac pacemakers. In an attempt to quantitatively investigate the electromagnetic interference caused by an induction oven on implantable unipolar cardiac pacemakers, we measured the distribution profile of the magnetic field intensity, both with and without a pan on the induction oven. We also performed the inhibition test and asynchronous test using four kinds of pacemakers housed in the standardized Irnich human body model, and measured the maximal distance from the induction oven up to which the interference occurred. In the pan-detection mode of the oven in the absence of a pan, the distribution profile of the magnetic field intensity peaked at the center of the cooking plate, and during induction heating of a pan placed on the induction oven, it was the largest at the circular top-edge of the pan. Pacemaker pulses were inhibited by the induction oven, or generated by the reversion mechanism. The maximal interference distance from the oven was 34 cm for one of the pacemakers. Thus, the safe distance from an induction oven of a patient with an implanted cardiac pacemaker is considered to be 50 cm or more. In conclusion, in the pan-detection mode of the oven in the absence of a pan, the distribution profile of the magnetic field intensity peaked at the center of the cooking plate, and during the induction heating of a pan placed on the oven, it peaked at the circular edge of the pan. The induction oven asynchronized or generated pulses in implantable unipolar cardiac pacemakers up to a maximal distance of 34 cm from the induction oven.

Interactive simulation system for artificial ventilation on the internet: virtual ventilator.

OBJECTIVE: To develop an interactive simulation system "virtual ventilator" that demonstrates the dynamics of pressure and flow in the respiratory system under the combination of spontaneous breathing, ventilation modes, and ventilator options. The simulation system was designed to be used by unexperienced health care professionals as a self-training tool. METHODS: The system consists of a simulation controller and three modules: respiratory, spontaneous breath, and ventilator. The respiratory module models the respiratory system by three resistances representing the main airway, the right and left lungs, and two compliances also representing the right and left lungs. The spontaneous breath module generates inspiratory negative pressure produced by a patient. The ventilator module generates driving force of pressure or flow according to the combination of the ventilation mode and options. These forces are given to the respiratory module through the simulation controller. RESULTS: The simulation system was developed using HTML, VBScript (3000 lines, 100 kB) and ActiveX control (120 kB), and runs on Internet Explorer (5.5 or higher). The spontaneous breath is defined by a frequency, amplitude and inspiratory patterns in the spontaneous breath module. The user can construct a ventilation mode by setting a control variable, phase variables (trigger, limit, and cycle), and options. Available ventilation modes are: controlled mechanical ventilation (CMV), continuous positive airway pressure, synchronized intermittent mandatory ventilation (SIMV), pressure support ventilation (PSV), SIMV + PSV, pressure-controlled ventilation (PCV), pressure-regulated volume control (PRVC), proportional assisted ventilation, mandatory minute ventilation (MMV), bilevel positive airway pressure (BiPAP). The simulation system demonstrates in a graph and animation the airway pressure, flow, and volume of the respiratory system during mechanical ventilation both with and without spontaneous breathing. CONCLUSIONS: We developed a web application that demonstrated the respiratory mechanics and the basic theory of ventilation mode.