An initiator- and catalyst-free hydrogel coating process for 3D printed medical-grade poly(ε-caprolactone).

Additive manufacturing or 3D printing as an umbrella term for various materials processing methods has distinct advantages over many other processing methods, including the ability to generate highly complex shapes and designs. However, the performance of any produced part not only depends on the material used and its shape, but is also critically dependent on its surface properties. Important features, such as wetting or fouling, critically depend mainly on the immediate surface energy. To gain control over the surface chemistry post-processing modifications are generally necessary, since it's not a feature of additive manufacturing. Here, we report on the use of initiator and catalyst-free photografting and photopolymerization for the hydrophilic modification of microfiber scaffolds obtained from hydrophobic medical-grade poly(ε-caprolactone) via melt-electrowriting. Contact angle measurements and Raman spectroscopy confirms the formation of a more hydrophilic coating of poly(2-hydroxyethyl methacrylate). Apart from surface modification, we also observe bulk polymerization, which is expected for this method, and currently limits the controllability of this procedure.

Applicability of Single-Layer Graphene as a Hydrogen-Blocking Interlayer in Low-Temperature PEMFCs.

Gas crossover is critical in proton exchange membrane (PEM)-based electrochemical systems. Recently, single-layer graphene (SLG) has gained great research interest due to its outstanding properties as a barrier layer for small molecules like hydrogen. However, the applicability of SLG as a gas-blocking interlayer in PEMs has yet to be fully understood. In this work, two different approaches for transferring SLG from a copper or a polymeric substrate onto PEMs are compared regarding their application in low-temperature PEM fuel cells. The SLG is sandwiched between two Nafion XL membranes to form a stable composite membrane. The successful transfer is confirmed by Raman spectroscopy and in ex situ hydrogen permeation experiments in the dry state, where a reduction of 50% upon SLG incorporation is achieved. The SLG composite membranes are characterized by their performance and hydrogen-blocking ability in a fuel cell setup at typical operating conditions of 80 °C and with fully humidified gases. The performance of the fuel cell incorporating an SLG composite membrane is equal to that of the reference cell when avoiding the direct etching process from a copper substrate, as remnants from copper etching deteriorate the performance of the fuel cell. For both transfer processes, the hydrogen crossover reduction of SLG composite membranes is only 15-19% (1.5 barabs) in the operating fuel cell. Further, hydrogen pumping experiments suggest that the barrier function of SLG impairs the water transport through the membrane, which may affect water management in electrochemical applications. In summary, this work shows the successful transfer of SLG into a PEM and confirms the effective hydrogen-blocking capability of the SLG interlayer. However, the hydrogen-blocking ability is significantly reduced when running the cell at the typical humidified operating conditions of PEM fuel cells, which follows from a combination of reversible interlayer alteration upon humidification and irreversible defect formation upon PEM fuel cell operation.

3D printing of bioreactors in tissue engineering: A generalised approach.

3D printing is a rapidly evolving field for biological (bioprinting) and non-biological applications. Due to a high degree of freedom for geometrical parameters in 3D printing, prototype printing of bioreactors is a promising approach in the field of Tissue Engineering. The variety of printers, materials, printing parameters and device settings is difficult to overview both for beginners as well as for most professionals. In order to address this problem, we designed a guidance including test bodies to elucidate the real printing performance for a given printer system. Therefore, performance parameters such as accuracy or mechanical stability of the test bodies are systematically analysed. Moreover, post processing steps such as sterilisation or cleaning are considered in the test procedure. The guidance presented here is also applicable to optimise the printer settings for a given printer device. As proof of concept, we compared fused filament fabrication, stereolithography and selective laser sintering as the three most used printing methods. We determined fused filament fabrication printing as the most economical solution, while stereolithography is most accurate and features the highest surface quality. Finally, we tested the applicability of our guidance by identifying a printer solution to manufacture a complex bioreactor for a perfused tissue construct. Due to its design, the manufacture via subtractive mechanical methods would be 21-fold more expensive than additive manufacturing and therefore, would result in three times the number of parts to be assembled subsequently. Using this bioreactor we showed a successful 14-day-culture of a biofabricated collagen-based tissue construct containing human dermal fibroblasts as the stromal part and a perfusable central channel with human microvascular endothelial cells. Our study indicates how the full potential of biofabrication can be exploited, as most printed tissues exhibit individual shapes and require storage under physiological conditions, after the bioprinting process.