Sb-Doped Cerium Molybdate: An Emerging Material as Dielectric and Photocatalyst for the Removal of Diclofenac Potassium from Aqueous Media.

This work reports the influence of antimony substitution in a cerium molybdate lattice for improved dielectric and photocatalytic properties. For this purpose, a series of Ce2-xSbx(MoO4)3 (x = 0.00, 0.01, 0.03, 0.05, 0.07, and 0.09) were synthesized through a co-precipitation route. The as-synthesized materials were characterized for their optical properties, functional groups, chemical oxidation states, structural phases, surface properties, and dielectric characteristics using UV-Vis spectroscopy (UV-Vis), Fourier transform infrared (FTIR) and Raman spectroscopies, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) analysis, and impedance spectroscopy, respectively. UV-Vis study showed a prominent red shift of absorption maxima and a continuous decrease in band gap (3.35 eV to 2.79 eV) by increasing the dopant concentration. The presence of Ce-O and Mo-O-Mo bonds, detected via FTIR and Raman spectroscopies, are confirmed, indicating the successful synthesis of the desired material. The monoclinic phase was dominant in all materials, and the crystallite size was decreased from 40.29 nm to 29.09 nm by increasing the Sb content. A significant increase in the dielectric constant (ε' = 2.856 × 108, 20 Hz) and a decrease in the loss tan (tanδ = 1.647, 20 Hz) were exhibited as functions of the increasing Sb concentration. Furthermore, the photocatalytic efficiency of pristine cerium molybdate was also increased by 1.24 times against diclofenac potassium by incorporating Sb (x = 0.09) in the cerium molybdate. The photocatalytic efficiency of 85.8% was achieved within 180 min of UV light exposure at optimized conditions. The photocatalytic reaction followed pseudo-first-order kinetics with an apparent rate constant of 0.0105 min-1, and the photocatalyst was recyclable with good photocatalytic activity even after five successive runs. Overall, the as-synthesized Sb-doped cerium molybdate material has proven to be a promising candidate for charge storage devices and a sustainable photocatalyst for wastewater treatment.

Development of Plumeria alba extract supplemented biodegradable films containing chitosan and cellulose derived from bagasse and corn cob waste for antimicrobial food packaging.

With the increase in global plastic pollution due to conventional plastic packaging (petroleum-derived), bioplastics have emerged as an alternative green source for practising a circular economy. This research aimed to extract cellulose from bagasse and corn cob waste and utilized in mixed form to prepare bioplastic film. The mixed cellulose was further reinforced with natural substances such as chitosan, bentonite, and P. alba extract. These newly developed bioplastics films were characterized by various physical tests like film thickness, moisture content, water solubility and spectroscopic techniques such as Fourier transform infrared (FTIR), scanning electron microscopy-energy dispersive spectroscopic (SEM-EDX), thermal gravimetric analysis (TGA), and ultraviolet-visible (UV-Vis) spectroscopy for opacity testing. The results revealed the enhanced bioplastic thermal and mechanical characteristics through robust interactions between cellulose and bentonite molecules. Moreover, incorporating chitosan solution as reinforcements in bio-composite films resulted in improved water barrier properties. The results indicated lower absorption in the UV range of 250-400 nm, attributed to the absence of UV-absorbing groups. Finally, their biodegradability was tested in soil, and 85.3 % weight loss of bioplastic films was observed after 50 days of the experiment which is the main task of this research. The antimicrobial properties of bioplastic films have been evaluated, and showed an inhibition zone of 16 mm against E. coli. After 12 days of incubation of sherbet berries, complete spoilage is identified in the control group compared to those covered with the bioplastic film. This outcome is attributed to the antioxidant and antimicrobial activities provided by chitosan and P. alba extract in the bioplastic film. The comprehensive outcomes of this study suggest the potential future adoption of these entirely bio-derived, environmentally sustainable and biodegradable bioplastic films as a viable substitute for the plastic packaging currently present in the market.

Development and characterization of a biodegradable film based on guar gum-gelatin@sodium alginate for a sustainable environment.

A significant amount of plastic trash has been dumped into the environment across the world, contributing to the present white pollution crisis. Therefore, plastic manufacturing and disposal must be examined. Biodegradable plastics (BPs) have recently become the subject of study due to their beneficial biodegradability and harmlessness, and they have been the most efficient method for addressing the issue of plastic pollution. This study aims to enhance the synthesis of biodegradable polymers from sodium alginate (Na-Alg) with the addition of guar gum, corn starch, and gelatin using the solution-casting method, followed by mixing in suitable proportions and drying at a certain temperature, resulting in thin film formation. To enhance qualities of the already produced polymer, additional substances such as glycerol, PVA, and latex were added as plasticizers. Characterization techniques such as scanning electron microscopy (SEM), tensile strength, thermogravimetric analysis (TGA), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), differential scanning calorimetry (DSC), UV-vis spectroscopy, and Fourier transform infrared (FTIR) spectroscopy were used to study structural characteristics, surface morphology, polymeric linkages, water absorption capabilities, chemical conductivity, and light transmittance of the newly formed films. These characterization results depict a remarkable achievement in the sense of the high degradability and impressive tensile strength of the newly formed films. In addition, SEM images indicated a porous structure with interconnected pores. FT-IR confirms the occurrence of molecular interactions between separate components. Consequently, different films showed different behavior of degradability, and it is suggested from interpreting the results that the polymeric films may be a viable biodegradable option.