Continuous Synthesis of Cinnarizine Salt with Malic Acid by Applying Green Chemistry Using Water-Assisted Twin Screw Extrusion.

Organic solvent-free process or green chemistry is needed for manufacturing pharmaceutical salts to avoid various environmental, safety, and manufacturing cost issues involved. In this study, a cinnarizine (CNZ) salt with malic acid at a 1:1 molar ratio was successfully prepared by twin screw extrusion (TSE) with water assistance. The feasibility of salt formation was first evaluated by screening several carboxylic acids by neat grinding (NG) and liquid-assisted grinding (LAG) using a mortar and pestle, which indicated that malic acid and succinic acid could form salts with CNZ. Further studies on salt formation were conducted using malic acid. The examination by hot-stage microscopy revealed that the addition of water could facilitate the formation and crystallization of CNZ-malic acid salt even though CNZ is poorly water-soluble. The feasibility of salt formation was confirmed by determining the pH-solubility relationship between CNZ and malic acid, where a pHmax of 2.7 and a salt solubility of 2.47 mg/mL were observed. Authentic salt crystals were prepared by solution crystallization from organic solvents for examining crystal properties and structure by differential scanning calorimetry (DSC), powder X-ray diffraction (PXRD), Fourier transform infrared (FTIR) spectroscopy, solid-state 13C and 15N nuclear magnetic resonance (NMR), and single-crystal X-ray diffraction (SXD). These techniques also established that a salt, and not a cocrystal, was indeed formed. The CNZ salt crystals were then prepared by TSE of a 1:1 CNZ-malic acid mixture, where the addition of small amounts of water resulted in a complete conversion of the mixture into the salt form. The salts prepared by solvent crystallization and water-assisted TSE had identical properties, and their moisture sorption profiles were also similar, indicating that TSE is a viable method for salt preparation by green chemistry. Since TSE can be conducted in a continuous manner, the results of the present investigation, if combined with other continuous processes, suggest the possibility of continuous manufacturing of drug products from the synthesis of active pharmaceutical ingredients (APIs) to the production of final dosage forms.

Continuous Preparation of 1:1 Haloperidol-Maleic Acid Salt by a Novel Solvent-Free Method Using a Twin Screw Melt Extruder.

Salts are generally prepared by acid-base reaction in relatively large volumes of organic solvents, followed by crystallization. In this study, the potential for preparing a pharmaceutical salt between haloperidol and maleic acid by a novel solvent-free method using a twin-screw melt extruder was investigated. The pH-solubility relationship between haloperidol and maleic acid in aqueous medium was first determined, which demonstrated that 1:1 salt formation between them was feasible (pHmax 4.8; salt solubility 4.7 mg/mL). Extrusion of a 1:1 mixture of haloperidol and maleic acid at the extruder barrel temperature of 60 °C resulted in the formation of a highly crystalline salt. The effects of operating temperature and screw configuration on salt formation were also investigated, and those two were identified as key processing parameters. Salts were also prepared by solution crystallization from ethyl acetate, liquid-assisted grinding, and heat-assisted grinding and compared with those obtained by melt extrusion by using DSC, PXRD, TGA, and optical microscopy. While similar salts were obtained by all methods, both melt extrusion and solution crystallization yielded highly crystalline materials with identical enthalpies of melting. During the pH-solubility study, a salt hydrate form was also identified, which, upon heating, converted to anhydrate similar to that obtained by other methods. There were previous reports of the formation of cocrystals, but not salts, by melt extrusion. 1H NMR and single-crystal X-ray diffraction confirmed that a salt was indeed formed in the present study. The haloperidol-maleic acid salt obtained was nonhygroscopic in the moisture sorption study and converted to the hydrate form only upon mixing with water. Thus, we are reporting for the first time a relatively simple and solvent-free twin-screw melt extrusion method for the preparation of a pharmaceutical salt that provides material comparable to that obtained by solution crystallization and is amenable to continuous manufacturing and easy scale up.

Biomimetic Taste Receptors with Chiral Recognition by Photoluminescent Metal-Organic Frameworks Chelated with Polyaniline Helices.

The adsorption of phenylaniline (Phe) enantiomers on (+)-polyaniline (PAN)-chelated [In(OH)(bdc)]n microcrystals was carefully designed and studied by using the Job titration, circular dichroism, X-ray photoelectron spectroscopy, and photoluminescence to mimic heterotrimeric guanine nucleotide-binding protein (G protein)-coupled receptors in selective, but not specific, ligand binding with chiral recognition and signal transduction. Six essential working principles across different length scales are unraveled: 1) a chiral (+)-PAN (host), 2) specific sites for Phe-(+)/PAN (guest-host) binding, 3) a conformational change of (+)-PAN after binding with Phe enantiomers, 4) different degrees of packing for (+)-PAN, 5) interactions between (+)-PAN and the underlying signal-generating framework (i.e., [In(OH)(bdc)]n microcrystals), and 6) a systematic photoluminescent signal combination by using principal-component analysis from the other three polymer-chelated metal-organic frameworkds (MOFs), such as poly(acrylic acid) (PAA), sodium alginate (SA), and polyvinylpyrrolidone (PVP) to enhance the selectivity and discrimination capabilities.

Propagation of biochirality: crossovers and nonclassical crystallization kinetics of aspartic acid in water.

All experimental procedures discussed could be treated as a screening tool for probing the existence of molecular association among the chiral molecules and the solvent system. The molecular association phases of a racemic conglomerate solution (CS) and a racemic compound solution (RCS), and the templating effect of aspartic acid solid surface were observed to minimize the chance of redissolving racemic conglomerate and racemic compound aspartic acid in water and reforming an RCS in crossovers experiments. Only 1 %wt% of l-aspartic acid was adequate enough to induce a transformation from a racemic compound aspartic acid to a racemic conglomerate aspartic acid. This would make the propagation of biochirality more feasible and sound. However, tetrapeptide, (l-aspartic acid)4 , failed to induce enantioseparation as templates purely by crystallization. Nonclassical crystallization theory was needed to take into account the existence of a CS. Fundamental parameters of the crystallization kinetics such as the induction time, interfacial energy, Gibbs energetic barrier, nucleation rate, and critical size of stable nuclei of: (i) racemic compound aspartic acid, (ii) racemic compound aspartic acid seeded with 1 %wt% l-aspartic acid, (iii) racemic conglomerate aspartic acid, and (iv) l-aspartic acid were evaluated and compared with different initial supersaturation ratios. Morphological studies of crystals grown from the crystallization kinetics were also carried out.

Crystallization of Form II Paracetamol with the Assistance of Carboxylic Acids toward Batch and Continuous Processes.

Form II paracetamol has captured the interest of researchers due to its improved compressibility. However, its low stability has made it difficult to be produced on a large scale with good reproducibility. In the present study, the selective polymorphic formation of paracetamol was carried out by cooling crystallization with four types of additives: adipic acid, fumaric acid, oxalic acid, and succinic acid. It was found that: (1) the more additives that were added, the higher the probability of forming Form II paracetamol; (2) Form II paracetamol could be induced by seeding the paracetamol aqueous solution with Form II paracetamol and fumaric acid crystals, and not the other three carboxylic acids; (3) a new solution complex of paracetamol-oxalic acid, evidenced by the solubility diagram, was responsible for the selective nucleation of Form II paracetamol in the oxalic acid aqueous solution; and (4) the range of the degree of supersaturation for nucleating Form II paracetamol was extended with the assistance of oxalic acid or fumaric acid. In large-scale crystallization, Form II paracetamol was produced by the continuous crystallization of 44 mg of paracetamol/mL in 50 wt% of fumaric acid aqueous solution with a flow rate of 150 mL/min.

Cadmium accumulation and tolerance of mahogany (Swietenia macrophylla) seedlings for phytoextraction applications.

Mahogany, a high biomass fast-growing tropical tree, has recently garnered considerable interest for potential use in heavy metal phytoremediation. This study performed hydroponic experiments with Cd concentration gradients at concentrations of 0, 7.5, 15, and 30 mg L(-1) to identify Cd accumulation and tolerance of mahogany (Swietenia macrophylla) seedlings as well as their potential for phytoextraction. Experimental results indicate that Cd inhibited mahogany seedling growth at the highest Cd exposure concentration (30 mg L(-1)). Nevertheless, this woody species demonstrated great potential for phytoextraction at Cd concentrations of 7.5 and 15 mg L(-1). The roots, twigs, and leaves had extremely large bioaccumulation factors at 10.3-65.1, indicating that the plant extracted large amounts of Cd from hydroponic solutions. Mahogany seedlings accumulated up to 154 mg kg(-1) Cd in twigs at a Cd concentration of 15 mg L(-1). Although Cd concentrations in leaves were <100 mg kg(-1), these concentrations markedly exceed the normal ranges for other plants. Due to the high biomass production and Cd uptake capacity of mahogany shoots, this plant is a potential candidate for remediating Cd-contaminated sites in tropical regions.

A Novel Hydrate Form of Sodium Dodecyl Sulfate and Its Crystallization Process.

A novel hydrate form of sodium dodecyl sulfate (SDS) was firstly discovered through a hydrate screening with the use of organic solvents, while SDS is generally prepared solely in aqueous media. Surprisingly, a novel SDS hydrate form with needle-shaped crystals produced by adding acetonitrile to a 20 wt % SDS aqueous solution at a ratio of 3:1 (v/v) and further cooling to around 5 °C could be found with a trace amount in one of the two purchased SDS products that we examined. After comprehensive solid-state characterizations by powder X-ray diffraction (PXRD), thermogravimetric analysis (TGA), Fourier transform infrared (FTIR), Raman spectroscopy, dynamic vapor sorption (DVS), and elemental analysis (EA), it is also successfully made directly from the synthesis of SDS through esterification and saponification. Four times the equal proportion of acetone was added into the reaction solution at an interval of 5 min to separate the side product, sodium sulfate, from the mother liquor. The desired novel hydrate form of SDS was then obtained by cooling the filtered mother liquor to 5 °C and aged for 8 h for a preferential growth.

Recovery of Active Pharmaceutical Ingredients from Unused Solid Dosage-Form Drugs.

The concept of drug recycle by recovering active pharmaceutical ingredients (APIs) from unused tablets and capsules was demonstrated using acetaminophen, tetracycline HCl, and (R,S)-(±)-ibuprofen as case examples. The recovery process comprised three core unit operations: solid-liquid extraction, filtration, and crystallization. Recovery yields of 58.7 wt %, 73.1 wt %, and 67.6 wt % for acetaminophen, tetracycline HCl, and (R,S)-(±)-ibuprofen were achieved, respectively. More importantly, all of the APIs were of high purity based on high-performance liquid chromatography assay. The crystal forms of the recovered APIs were in conformity with the standards.

Effects of baffle configuration and tank size on spherical agglomerates of dimethyl fumarate in a common stirred tank.

To pave the way for technology transfer and scale up of the spherical agglomeration (SA) process for dimethyl fumarate, effects of the US, European and Kawashima type baffles and 0.5, 2.0 and 10 L-sized common stirred tank were studied. It was found that the particle size distribution varied significantly. However, the size-related properties such as dissolution profile and flowability of agglomerates from the same size cut after sieving could remain unchanged. The interior structure-related properties such as particle density and mechanical property of agglomerates upon baffle change and scale up from the same size cut were decayed and the agglomerates could become denser and stronger by prolonged maturation time. To maintain the same size distribution, agglomerates from any batch could have been separated and classified by sieving and then blended back together artificially by the desired weight% of each cut.

Effectiveness of hyaluronic acid administration in treating adhesive capsulitis of the shoulder: a systematic review of randomized controlled trials.

INTRODUCTION: Adhesive capsulitis (AC) of the shoulder presents with an insidious onset of pain and progressive limitation of shoulder movement. OBJECTIVES: To investigate whether intra-articular hyaluronic acid (HA) administration alone is superior to conventional therapies and whether the addition of intra-articular HA administration to conventional therapies improves clinical outcomes in patients with AC. METHODS: The PubMed, EMBASE, CINAHL, and Cochrane Library electronic databases were searched without language restrictions in July 2014 with a priori defined inclusion and exclusion criteria. RESULTS: Four randomized controlled trials (273 participants, 278 shoulders) were included in this review. Two trials compared intra-articular HA administration with conventional therapies and 2 trials evaluated intra-articular HA administration as an addition to conventional therapies. Pain and shoulder function/disability outcomes in the HA injection group were not superior to those achieved in the conventional therapy groups. No significant differences in pain or shoulder function/disability outcomes were noted between the groups with and without adjunctive HA administration. CONCLUSIONS: Intra-articular HA administration alone is not superior to conventional AC treatments, and the addition of intra-articular HA administration to conventional therapies does not provide significant added benefits. HA administration in AC patients who are receiving conventional therapies should be evaluated to avoid unnecessary medical expenditure.