Proof of Concept for Sustainable Manufacturing of Neural Electrode Array for In Vivo Recording.

Increasing requirements for neural implantation are helping to expand our understanding of nervous systems and generate new developmental approaches. It is thanks to advanced semiconductor technologies that we can achieve the high-density complementary metal-oxide-semiconductor electrode array for the improvement of the quantity and quality of neural recordings. Although the microfabricated neural implantable device holds much promise in the biosensing field, there are some significant technological challenges. The most advanced neural implantable device relies on complex semiconductor manufacturing processes, which are required for the use of expensive masks and specific clean room facilities. In addition, these processes based on a conventional photolithography technique are suitable for mass production, which is not applicable for custom-made manufacturing in response to individual experimental requirements. The microfabricated complexity of the implantable neural device is increasing, as is the associated energy consumption, and corresponding emissions of carbon dioxide and other greenhouse gases, resulting in environmental deterioration. Herein, we developed a fabless fabricated process for a neural electrode array that was simple, fast, sustainable, and customizable. An effective strategy to produce conductive patterns as the redistribution layers (RDLs) includes implementing microelectrodes, traces, and bonding pads onto the polyimide (PI) substrate by laser micromachining techniques combined with the drop coating of the silver glue to stack the laser grooving lines. The process of electroplating platinum on the RDLs was performed to increase corresponding conductivity. Sequentially, Parylene C was deposited onto the PI substrate to form the insulation layer for the protection of inner RDLs. Following the deposition of Parylene C, the via holes over microelectrodes and the corresponding probe shape of the neural electrode array was also etched by laser micromachining. To increase the neural recording capability, three-dimensional microelectrodes with a high surface area were formed by electroplating gold. Our eco-electrode array showed reliable electrical characteristics of impedance under harsh cyclic bending conditions of over 90 degrees. For in vivo application, our flexible neural electrode array demonstrated more stable and higher neural recording quality and better biocompatibility as well during the 2-week implantation compared with those of the silicon-based neural electrode array. In this study, our proposed eco-manufacturing process for fabricating the neural electrode array reduced 63 times of carbon emissions compared to the traditional semiconductor manufacturing process and provided freedom in the customized design of the implantable electronic devices as well.

Food Quality Monitor: Paper-Based Plasmonic Sensors Prepared Through Reversal Nanoimprinting for Rapid Detection of Biogenic Amine Odorants.

This paper describes the fabrication of paper-based plasmonic refractometric sensors through the embedding of metal nanoparticles (NPs) onto flexible papers using reversal nanoimprint lithography. The NP-embedded papers can serve as gas sensors for the detection of volatile biogenic amines (BAs) released from spoiled food. Commercial inkjet papers were employed as sensor substrates-their high reflectance (>80%) and smooth surfaces (roughness: ca. 4.9 nm) providing significant optical signals for reflection-mode plasmonic refractometric sensing and high particle transfer efficiency, respectively; in addition, because inkjet papers have lightweight and are burnable and flexible, they are especially suitable for developing portable, disposable, cost-effective, eco-friendly sensing platforms. Solid silver NPs (SNPs), solid gold NPs (GNPs), and hollow Au-Ag alloyed NPs (HGNs) were immobilized on a solid mold and then transferred directly onto the softened paper surfaces. The particle number density and exposure height of the embedded NPs were dependent on two imprinting parameters: applied pressure and temperature. The optimal samples exhibited high particle transfer efficiency (ca. 85%), a sufficient exposure surface area (ca. 50% of particle surface area) presented to the target molecules, and a strong resonance reflectance dip for detection. Moreover, the HGN-embedded paper displayed a significant wavelength dip shift upon the spontaneous adsorption of BA vapors (e.g., Δλ = 33 nm for putrescine; Δλ = 24 nm for spermidine), indicating high refractometric sensitivity; in contrast, no visible spectroscopic responses were observed with respect to other possibly coexisting gases (e.g., air, N2, CO2, water vapor) during the food storage process, indicating high selectivity. Finally, the plasmonic sensing papers were used to monitor the freshness of a food product (salmon).