Preparation and Characterization of Bismaleimide-Resin-Based Composite Materials.

This study utilized bismaleimide (BMI) resin, reinforced with introduced ether bonds, as a binding matrix, in combination with silicon carbide (SiC), for the fabrication of composite materials. A thorough investigation was conducted to assess the influence of diverse processing parameters on the mechanical properties and high-temperature thermo-oxidative stability of these composites. Experimental results indicate a notable improvement in the mechanical properties of the composites upon the incorporation of ether bonds, in contrast to their unmodified counterparts. The variation in performance among composites with different ratios and molding densities is apparent. Within a certain range, an increase in resin content and molding density is correlated with improved bending strength in the composites. With a resin content of 27.5 vol% and a molding density of 2.31 g/cm3, the composite achieved a maximum flexural strength of 109.52 MPa, representing a 24% increase compared to its pre-modification state. Even after exposure to high-temperature heat treatment, the composites displayed commendable mechanical properties compared to their pre-ether bond modification counterparts, maintaining 74.5% of the strength of the untreated composites at 300 °C. The scanning electron microscopy (SEM) microstructures of composite materials correlate remarkably well with their mechanical properties.

Research on Sol-Gel Synthesis of Low-Temperature Na2O-B2O3-SiO2 Vitrified Bonds and Preparation of High-Strength Stacked Abrasives Using the Molding and Crushing Method.

Currently, the sol-gel technique is employed in the synthesis of high-performance vitrified bonds; however, its application in the fabrication of stacked abrasives has been minimally explored. Furthermore, the methods utilized in the production of abrasive particles for stacked abrasives are technically challenging and incur high costs, which hinders their actual industrial application. Consequently, this study utilizes the sol-gel approach to synthesize a Na2O-B2O3-SiO2 ternary system vitrified bond powder and employs a molding and crushing method, which offers a lower technological barrier and reduced preparation costs, for the production of abrasive particles subsequently fabricating corundum stacked abrasives. Upon setting the binder composition to a molar ratio of n(SiO2):n(B2O3):n(Na2O) = 65:23:12, it was observed that the crystallization within the glass matrix was minimized and the optimal sintering temperature for the synthesized laminate abrasive to be sustained at 820 °C. At the aforementioned temperature, the binder melt is capable of flowing uniformly amongst the abrasive granules, thereby ensuring a robust encapsulation of the particles. The average single particle compressive strength of the prepared corundum stacked abrasive with a grain size of forty mesh can reach the highest of all composition points at 28.56 N and the average single particle compressive strength of the prepared diamond stacked abrasive is 28.14 N.

Genome-wide identification and analysis of highly specific CRISPR/Cas9 editing sites in pepper (Capsicum annuum L.).

The CRISPR/Cas9 system is an efficient genome editing tool that possesses the outstanding advantages of simplicity and high efficiency. Genome-wide identification and specificity analysis of editing sites is an effective approach for mitigating the risk of off-target effects of CRISPR/Cas9 and has been applied in several plant species but has not yet been reported in pepper. In present study, we first identified genome-wide CRISPR/Cas9 editing sites based on the 'Zunla-1' reference genome and then evaluated the specificity of CRISPR/Cas9 editing sites through whole-genome alignment. Results showed that a total of 603,202,314 CRISPR/Cas9 editing sites, including 229,909,837 (~38.11%) NGG-PAM sites and 373,292,477 (~61.89%) NAG-PAM sites, were detectable in the pepper genome, and the systematic characterization of their composition and distribution was performed. Furthermore, 29,623,855 highly specific NGG-PAM sites were identified through whole-genome alignment analysis. There were 26,699,38 (~90.13%) highly specific NGG-PAM sites located in intergenic regions, which was 9.13 times of the number in genic regions, but the average density in genic regions was higher than that in intergenic regions. More importantly, 34,251 (~96.93%) out of 35,336 annotated genes exhibited at least one highly specific NGG-PAM site in their exons, and 90.50% of the annotated genes exhibited at least 4 highly specific NGG- PAM sites, indicating that the set of highly specific CRISPR/Cas9 editing sites identified in this study was widely applicable and conducive to the minimization of the off-target effects of CRISPR/Cas9 in pepper.