Effects of fuel components and combustion particle physicochemical properties on toxicological responses of lung cells.

The physicochemical properties of combustion particles that promote lung toxicity are not fully understood, hindered by the fact that combustion particles vary based on the fuel and combustion conditions. Real-world combustion-particle properties also continually change as new fuels are implemented, engines age, and engine technologies evolve. This work used laboratory-generated particles produced under controlled combustion conditions in an effort to understand the relationship between different particle properties and the activation of established toxicological outcomes in human lung cells (H441 and THP-1). Particles were generated from controlled combustion of two simple biofuel/diesel surrogates (methyl decanoate and dodecane/biofuel-blended diesel (BD), and butanol and dodecane/alcohol-blended diesel (AD)) and compared to a widely studied reference diesel (RD) particle (NIST SRM2975/RD). BD, AD, and RD particles exhibited differences in size, surface area, extractable chemical mass, and the content of individual polycyclic aromatic hydrocarbons (PAHs). Some of these differences were directly associated with different effects on biological responses. BD particles had the greatest surface area, amount of extractable material, and oxidizing potential. These particles and extracts induced cytochrome P450 1A1 and 1B1 enzyme mRNA in lung cells. AD particles and extracts had the greatest total PAH content and also caused CYP1A1 and 1B1 mRNA induction. The RD extract contained the highest relative concentration of 2-ring PAHs and stimulated the greatest level of interleukin-8 (IL-8) and tumor necrosis factor-alpha (TNFα) cytokine secretion. Finally, AD and RD were more potent activators of TRPA1 than BD, and while neither the TRPA1 antagonist HC-030031 nor the antioxidant N-acetylcysteine (NAC) affected CYP1A1 or 1B1 mRNA induction, both inhibitors reduced IL-8 secretion and mRNA induction. These results highlight that differences in fuel and combustion conditions affect the physicochemical properties of particles, and these differences, in turn, affect commonly studied biological/toxicological responses.

Ash particulate formation from pulverized coal under oxy-fuel combustion conditions.

Aerosol particulates are generated by coal combustion. The amount and properties of aerosol particulates, specifically size distribution and composition, can be affected by combustion conditions. Understanding the formation of these particles is important for predicting emissions and understanding potential deposition. Oxy-fuel combustion conditions utilize an oxygen-enriched gas environment with CO(2). The high concentration of CO(2) is a result of recycle flue gas which is used to maintain temperature. A hypothesis is that high CO(2) concentration reduces the vaporization of refractory oxides from combustion. A high-temperature drop-tube furnace was used under different oxygen concentrations and CO(2) versus N(2) to study the effects of furnace temperature, coal type, and gas phase conditions on particulate formation. A scanning mobility particle sizer (SMPS) and aerodynamic particle sizer (APS) were utilized for particle size distributions ranging from 14.3 nm to 20 µm. In addition, particles were collected on a Berner low pressure impactor (BLPI) for elemental analysis using scanning electron microscopy and energy dispersive spectroscopy. Three particle size modes were seen: ultrafine (below 0.1 µm), fine (0.1 to 1.0 µm), and coarse (above 1 µm). Ultrafine mass concentrations were directly related to estimated particle temperature, increasing with increasing temperature. For high silicon and calcium coals, Utah Skyline and PRB, there was a secondary effect due to CO(2) and the hypothesized reaction. Illinois #6, a high sulfur coal, had the highest amount of ultrafine mass and most of the sulfur was concentrated in the ultrafine and fine modes. Fine and coarse mode mass concentrations did not show a temperature or CO(2) relationship. (The table of contents graphic and abstract graphic are adapted from ref 27.).

Low-wind/high particulate matter episodes in the Calexico/Mexicali region.

The U.S. Environmental Protection Agency (EPA) currently classifies Imperial County, CA, as a nonattainment area for PM10 (particulate matter [PM] < or = 10 microm in diameter), and this region suffers from high rates of chronic bronchitis and childhood asthma. Although high annual and daily average PM levels can have negative health and economic effects, recent studies have identified an association between adverse health effects and short-term PM spikes of tens of micrograms per cubic meter. This study identified PM episodes in Calexico/Mexicali that involve PM concentration spikes with concentrations up to 10 times greater than those reported to cause adverse health effects. These episodes appear to be relatively common during the winter months, are associated with wind speeds below 2 m/sec and stable boundary level heights below 500 m, and can comprise a large portion of the 24-hr PM levels. The organic composition of the PM10 samples collected during the low-wind/ high-PM episodes differed from that collected at other times. However, a preliminary source attribution identified only one significant difference between the source classes: agricultural burning accounted for 6.7% of organic-fraction PM10 for low-wind/high-PM episodes versus 0.25% at other times. This preliminary source attribution also revealed that motor vehicles were the most important relative contributor to organic PM10.

Report: Combustion Byproducts and Their Health Effects: Summary of the 10th International Congress.

The 10th International Congress on Combustion Byproducts and their Health Effects was held in Ischia, Italy, from June 17-20, 2007. It is sponsored by the US NIEHS, NSF, Coalition for Responsible Waste Incineration (CRWI), and Electric Power Research Institute (EPRI). The congress focused on: the origin, characterization, and health impacts of combustion-generated fine and ultrafine particles; emissions of mercury and dioxins, and the development/application of novel analytical/diagnostic tools. The consensus of the discussion was that particle-associated organics, metals, and persistent free radicals (PFRs) produced by combustion sources are the likely source of the observed health impacts of airborne PM rather than simple physical irritation of the particles. Ultrafine particle-induced oxidative stress is a likely progenitor of the observed health impacts, but important biological and chemical details and possible catalytic cycles remain unresolved. Other key conclusions were: (1) In urban settings, 70% of airborne fine particles are a result of combustion emissions and 50% are due to primary emissions from combustion sources, (2) In addition to soot, combustion produces one, possibly two, classes of nanoparticles with mean diameters of ~10 nm and ~1 nm. (3) The most common metrics used to describe particle toxicity, viz. surface area, sulfate concentration, total carbon, and organic carbon, cannot fully explain observed health impacts, (4) Metals contained in combustion-generated ultrafine and fine particles mediate formation of toxic air pollutants such as PCDD/F and PFRs. (5) The combination of metal-containing nanoparticles, organic carbon compounds, and PFRs can lead to a cycle generating oxidative stress in exposed organisms.

Black carbon and polycyclic aromatic hydrocarbon emissions from vehicles in the United States-Mexico border region: pilot study.

The investigators developed a system to measure black carbon (BC) and particle-bound polycyclic aromatic hydrocarbon (PAH) emission factors during roadside sampling in four cities along the United States-Mexico border, Calexico/Mexicali and El Paso/Juarez. The measurement system included a photoacoustic analyzer for BC, a photoelectric aerosol sensor for particle-bound PAHs, and a carbon dioxide (CO2) analyzer. When a vehicle with measurable emissions passed the system probe, corresponding BC, PAH, and CO2 peaks were evident, and a fuel-based emission factor was estimated. A picture of each vehicle was also recorded with a digital camera. The advantage of this system, compared with other roadside methods, is the direct measurement of particulate matter components and limited interference from roadside dust. The study revealed some interesting trends: Mexican buses and all medium-duty trucks were more frequently identified as high emitters of BC and PAH than heavy-duty trucks or passenger vehicles. In addition, because of the high daily mileage of buses, they are good candidates for additional study. Mexican trucks and buses had higher average emission factors compared with U.S. trucks and buses, but the differences were not statistically significant. Few passenger vehicles had measurable BC and PAH emissions, although the highest emission factor came from an older model passenger vehicle licensed in Baja California.

Simulation of the evolution of particle size distributions in a vehicle exhaust plume with unconfined dilution by ambient air.

Over the past several years, numerous studies have linked ambient concentrations of particulate matter (PM) to adverse health effects, and more recent studies have identified PM size and surface area as important factors in determining the health effects of PM. This study contributes to a better understanding of the evolution of particle size distributions in exhaust plumes with unconfined dilution by ambient air. It combines computational fluid dynamics (CFD) with an aerosol dynamics model to examine the effects of different streamlines in an exhaust plume, ambient particle size distributions, and vehicle and wind speed on the particle size distribution in an exhaust plume. CFD was used to calculate the flow field and gas mixing for unconfined dilution of a vehicle exhaust plume, and the calculated dilution ratios were then used as input to the aerosol dynamics simulation. The results of the study show that vehicle speed affected the particle size distribution of an exhaust plume because increasing vehicle speed caused more rapid dilution and inhibited coagulation. Ambient particle size distributions had an effect on the smaller sized particles (approximately 10 nm range under some conditions) and larger sized particles (>2 microm) of the particle size distribution. The ambient air particle size distribution affects the larger sizes of the exhaust plume because vehicle exhaust typically contains few particles larger than 2 microm. Finally, the location of a streamline in the exhaust plume had little effect on the particle size distribution; the particle size distribution along any streamline at a distance x differed by less than 5% from the particle size distributions along any other streamline at distance x.

Real-time measurements of jet aircraft engine exhaust.

Particulate-phase exhaust properties from two different types of ground-based jet aircraft engines--high-thrust and turboshaft--were studied with real-time instruments on a portable pallet and additional time-integrated sampling devices. The real-time instruments successfully characterized rapidly changing particulate mass, light absorption, and polycyclic aromatic hydrocarbon (PAH) content. The integrated measurements included particulate-size distributions, PAH, and carbon concentrations for an entire test run (i.e., "run-integrated" measurements). In all cases, the particle-size distributions showed single modes peaking at 20-40nm diameter. Measurements of exhaust from high-thrust F404 engines showed relatively low-light absorption compared with exhaust from a turboshaft engine. Particulate-phase PAH measurements generally varied in phase with both net particulate mass and with light-absorbing particulate concentrations. Unexplained response behavior sometimes occurred with the real-time PAH analyzer, although on average the real-time and integrated PAH methods agreed within the same order of magnitude found in earlier investigations.

Particle characteristics responsible for effects on human lung epithelial cells.

Some recent epidemiologic investigations have shown an association between increased incidence of respiratory symptoms and exposure to low levels of particulate matter (PM*) less than 10 microm or less than 2.5 microm in aerodynamic diameter (PM10 and PM2.5, respectively). If particulates are causally involved with respiratory symptoms, it is important to understand which components may be responsible. However, increasing evidence suggests that transition metals present in particles, especially iron, generate reactive oxygen species (ROS) that may be involved in producing some of the observed respiratory symptoms. The hypothesis for this study is twofold: bioavailable transition metals from inhaled airborne particulates catalyze redox reactions in human lung epithelial cells, leading to oxidative stress and increased production of mediators of pulmonary inflammation: and the size, transition metal content, and mineral speciation of particulates affect their ability to cause these effects. This work focused on the relation between physical characteristics of particles (eg, size, bioavailable transition metal content, and mineral speciation) and their ability to generate hydroxyl radicals in cell-free systems and to cause oxidative stress, which results in the synthesis of mediators of pulmonary inflammation in cultured human lung epithelial cells. These relations were studied by comparing size-fractionated, chemically characterized coal fly ash (CFA) produced by combustion of three different coals to obtain milligram quantities of ash. One transition metal, iron, was studied specifically because it is by far the predominant transition metal in CFA. In addition, smaller quantities of particles from gasoline engines, diesel engines, and ambient air were studied. Phosphate buffer soluble fractions from particles from all sources were capable of generating ROS, as measured by production of malondialdehyde (MDA) from 2-deoxyribose. This activity was inhibited over 90% for all particles by the metal chelator N-[5-[3-[(5-aminopentyl)hydroxycarbamoyl]propionamidol-pentyl]-3-[[5-(N-hydroxyacetamido)pentyl]carbamoyl]propionohydroxamic acid (desferrioxamine B, or DF), strongly suggesting that transition metal(s), probably iron, were responsible. Particles from coal or gasoline combustion had greater ability to produce ROS than particles from diesel combustion. Iron was mobilized by citrate (at pH 7.5) from particles of all sources tested; gasoline combustion particles were the only particles not analyzed for iron mobilization because there were not enough particles for the iron mobilization assay. CFA particles were size-fractioned; the amount of iron mobilized by citrate was inversely related to the size of particles and also depended on the source of coal. Iron from the CFA particles was responsible for inducing the iron-storage protein ferritin in cultured human lung epithelial cells (A549 cells). The amount of iron mobilized by citrate was directly proportional to the amount of ferritin induced in the A549 cells. Iron from the CFA was also responsible for inducing the inflammatory mediator interleukin (IL) 8 in A549 cells. Iron existed in several species in the fly ash, but the bioavailable iron was associated with the glassy aluminosilicate fraction, which caused ferritin and IL-8 to be induced in the A549 cells. In crustal dust, another component of urban particulates, iron was associated with oxides and clay but not with aluminosilicates. The crustal dust contained almost no iron that could be mobilized by citrate. Iron could be mobilized from diesel combustion particulates, but at a much lower level than for all other combustion particles. Samples of ambient PM2.5 collected in Salt Lake City over 5-day periods during one month varied widely in the amount of iron that could be mobilized. If bioavailable transition metals (eg, iron) are related to the specific biological responses outlined here, then the potential exists to develop in vitro assays to determine whether particulates of unknown composition and origin can cause effects similar to those observed in this study.

Characterization of exhaust particles from military vehicles fueled with diesel, gasoline, and JP-8.

Diluted exhaust from selected military aircraft ground-support equipment (AGE) was analyzed for particulate mass, elemental carbon (EC) and organic carbon (OC), SO4(2-), and size distributions. The experiments occurred at idle and load conditions and utilized a chassis dynamometer. The selected AGE vehicles operated on gasoline, diesel, and JP-8. These military vehicles exhibited concentrations, size distributions, and emission factors in the same range as those reported for nonmilitary vehicles. The diesel and JP-8 emission rates for PM ranged from 0.092 to 1.1 g/kg fuel. The EC contributed less and the OC contributed more to the particulate mass than reported in recent studies of vehicle emissions. Overall, the particle size distribution varied significantly with engine condition, with the number of accumulation mode particles and the count median diameter (CMD) increasing as engine load increased. The SO4(2-) analyses showed that the distribution of SO4(2-) mass mirrored the distribution of particle mass.

Evaluation of catalyzed and electrically heated filters for removal of particulate emissions from diesel-A- and JP-8-fueled engines.

In-service diesel engines are a significant source of particulate matter (PM) emissions, and they have been subjected to increasingly strict emissions standards. Consequently, the wide-scale use of some type of particulate filter is expected. This study evaluated the effect of an Engelhard catalyzed soot filter (CSF) and a Rypos electrically heated soot filter on the emissions from in-service diesel engines in terms of PM mass, black carbon concentration, particle-bound polycyclic aromatic hydrocarbon concentration, and size distribution. Both filters capture PM. The CSF relies on the engine's exhaust to reach the catalyst regeneration temperature and oxidize soot, whereas the electrically heated filter contains a heating element to oxidize soot. The filters were installed on several military diesel engines. Particle concentrations and compositions were measured before and after installation of the filter and again after several months of operation. Generally, the CSF removed at least 90% of total PM, and the removal efficiency improved or remained constant after several months of operation. In contrast, the electrical filters removed 44-69% of PM mass. In addition to evaluating the soot filters, the sampling team also compared the results of several real-time particle measurement instruments to traditional filter measurements of total mass.

Confounding effects of aqueous-phase impinger chemistry on apparent oxidation of mercury in flue gases.

Gas-phase reactions between elemental mercury and chlorine are a possible pathway to producing oxidized mercury species such as mercuric chloride in combustion systems. This study examines the effect of the chemistry of a commonly used sample conditioning system on apparent and actual levels of mercury oxidation in a methane-fired, 0.3 kW, quartz-lined reactor in which gas composition (HCl, Cl2, NOx, SO2) and quench rate were varied. The sample conditioning system included two impingers in parallel: one containing an aqueous solution of KCl to trap HgCl2, and one containing an aqueous solution of SnCl2 to reduce HgCl2 to elemental mercury (Hg0). Gas-phase concentrations of Cl2 as low as 1.5 ppmv were sufficient to oxidize a significant fraction of the elemental mercury in the KCl impinger via the hypochlorite ion. Furthermore, these low, but interfering levels of Cl2 appeared to persist in flue gases from several doped rapidly mixed flames with varied post flame temperature quench rates. The addition of 0.5 wt% sodium thiosulfate to the KCl solution completely prevented the oxidation from occurring in the impinger. The addition of thiosulfate did not inhibit the KCl impinger's ability to capture HgCl2. The effectiveness of the thiosulfate was unchanged by NO or SO2. These results bring into question laboratory scale experimental data on mercury oxidation where wet chemistry was used to partition metallic and oxidized mercury without the presence of sufficient levels of SO2.