RESUMO
Polarization mode dispersion is recognized as a key factor limiting optical transmission systems, particularly those fiber links that run at bit rates beyond 10 Gbps. In-line test and characterization of polarization mode dispersion are thus of critical importance to evaluate the quality of installed optical fibers that are in use for high-speed signal traffics. However, polarization-based effects in optical fibers are stochastic and quite sensitive to a range of environmental changes, including optical cable movements. This, in turn, gives rise to undesired variations in light polarization that adversely impair the quality of the signal transmission in the link. In this work, we elaborate on experimental testing and theoretical analysis to asses changes of polarization mode dispersion in optical fibers that are caused by environmental variations, here wind gusts in particular. The study was performed on commercially harnessed optical fibers installed within optical power ground wire cables, taking into account different weather conditions. More specifically, we showed that changes caused by wind gusts significantly influence the differential group delay and the principal state of polarization in those optical fibers. For this, we experimentally measured a number of parameters to characterize light polarization properties. Measurements were carried out on C-band operated fiber-optic link formed by 111-km-long power ground wire cables and 88 spectral channels, with a test time step of 1 min during 12 consecutive days. Variations in differential group delay allowed for sensitive testing of environmental changes with measured maxims up to 10 ps under the worst wind conditions. Moreover, measured parameters were used in a numerical model to assess the quality of transmitted high-bit-rate optical signals as a function of wind conditions. The analysis revealed a negligible impact of wind on a 10 Gbps transmission, while substantial influence was noticed for higher bit rates up to 100 Gbps. These results show promises for efficient sensing of environmental changes and subsequent monitoring of the quality of recently used fiber-optic link infrastructures.
RESUMO
Properties of reflection and transmission spectral filters based on Bragg gratings in subwavelength grating (SWG) metamaterial waveguides on silicon-on-insulator platform have been analyzed using proprietary 2D and 3D simulation tools based on Fourier modal method and the coupled-mode theory. We also demonstrate that the coupled Bloch mode theory can be advantageously applied to design of Bragg gratings in SWG waveguides. By combining different techniques, including judiciously positioning silicon loading segments within the evanescent field of the SWG waveguide and making use of its dispersion properties, it is possible to attain sub-nanometer spectral bandwidths for both reflection and transmission filters in the wavelength range of 1550 nm while keeping minimum structural features of the filters as large as 100 nm. Numerical simulations have also shown that a few nanometer jitter in the size and position of Si segments is well tolerated in our filter designs.
RESUMO
Silicon nitride (Si3N4) is an ideal candidate for the development of low-loss photonic integrated circuits. However, efficient light coupling between standard optical fibers and Si3N4 chips remains a significant challenge. For vertical grating couplers, the lower index contrast yields a weak grating strength, which translates to long diffractive structures, limiting the coupling performance. In response to the rise of hybrid photonic platforms, the adoption of multi-layer grating arrangements has emerged as a promising strategy to enhance the performance of Si3N4 couplers. In this work, we present the design of high-efficiency surface grating couplers for the Si3N4 platform with an amorphous silicon (α-Si) overlay. The surface grating, fully formed in an α-Si waveguide layer, utilizes subwavelength grating (SWG)-engineered metamaterials, enabling simple realization through single-step patterning. This not only provides an extra degree of freedom for controlling the fiber-chip coupling but also facilitates portability to existing foundry fabrication processes. Using rigorous three-dimensional (3D) finite-difference time-domain (FDTD) simulations, a metamaterial-engineered grating coupler is designed with a coupling efficiency of -1.7 dB at an operating wavelength of 1.31 µm, with a 1 dB bandwidth of 31 nm. Our proposed design presents a novel approach to developing high-efficiency fiber-chip interfaces for the silicon nitride integration platform for a wide range of applications, including datacom and quantum photonics.