An affordable implantable vagus nerve stimulator system for use in animal research.

In this research, a vagus nerve stimulator has been developed and miniaturized for use in epilepsy research. The board contains all the components necessary for its operation during the standard duration of the experiments, being possible to control it once implanted and even being able to reuse it. The VNS system has been designed for rodents since the VNS devices available for human are not only too large for laboratory animals, but also too expensive. With this solution the expenditure on materials made by laboratories is greatly reduced and bioethical considerations were kept in mind. The system was validated in hamsters. This article is part of the theme issue 'Advanced neurotechnologies: translating innovation for health and well-being'.

Validation of Embedded State Estimator Modules for Decentralized Monitoring of Power Distribution Systems Using IoT Components.

Recent theoretical studies demonstrate the advantages of using decentralized architectures over traditional centralized architectures for real-time Power Distribution Systems (PDSs) operation. These advantages include the reduction of the amount of data to be transmitted and processed when performing state estimation in PDSs. The main contribution of this paper is to provide lab validation of the advantages and feasibility of decentralized monitoring of PDSs. Therefore, this paper presents an advanced trial emulating realistic conditions and hardware setup. More specifically, the paper proposes: (i) The laboratory development and implementation of an Advanced Measurement Infrastructure (AMI) prototype to enable the simulation of a smart grid. To emulate the information traffic between smart meters and distribution operation centers, communication modules, that enable the use of wireless networks for sending messages in real-time, are used, bridging concepts from both IoT and Edge Computing. (ii) The laboratory development and implementation of a decentralized architecture based on Embedded State Estimator Modules (ESEMs) are carried out. ESEMs manage information from smart meters at lower voltage networks, performing real-time state estimation in PDSs. Simulations performed on a real PDS with 208 buses (considering both medium and low voltage buses) have met the aims of this paper. The results show that by using ESEMs in a decentralized architecture, both the data transit through the communication network, as well as the computational requirements involved in monitoring PDSs in real-time, are reduced considerably without any loss of accuracy.

BeSafe B2.0 Smart Multisensory Platform for Safety in Workplaces.

Wearable technologies are becoming a profitable means of monitoring a person's health state, such as heart rate and physical activity. The use of the smartwatch is becoming consolidated, not only as a novelty but also as a very useful tool for daily use. In addition, other devices, such as helmets or belts, are beneficial for monitoring workers and the early detection of any anomaly. They can provide valuable information, especially in work environments, where they help reduce the rate of accidents and occupational diseases, which makes them powerful Personal Protective Equipment (PPE). The constant monitoring of the worker's health can be done in real-time, through temperature, falls, noise, impacts, or heart rate meters, activating an audible and vibrating alarm when an anomaly is detected. The gathered information is transmitted to a server in charge of collecting and processing it. In the first place, this paper provides an exhaustive review of the state of the art on works related to electronics for human activity behavior. After that, a smart multisensory bracelet, combined with other devices, developed a control platform that can improve operators' security in the working environment. Artificial Intelligence and the Internet of Things (AIoT) bring together the information to improve safety on construction sites, power stations, power lines, etc. Real-time and historic data is used to monitor operators' health and a hybrid system between Gaussian Mixture Model and Human Activity Classification. That is, our contribution is also founded on the use of two machine learning models, one based on unsupervised learning and the other one supervised. Where the GMM gave us a performance of 80%, 85%, 70%, and 80% for the 4 classes classified in real time, the LSTM obtained a result under the confusion matrix of 0.769, 0.892, and 0.921 for the carrying-displacing, falls, and walking-standing activities, respectively. This information was sent in real time through the platform that has been used to analyze and process the data in an alarm system.

Intelligent Platform Based on Smart PPE for Safety in Workplaces.

It is estimated that we spend one-third of our lives at work. It is therefore vital to adapt traditional equipment and systems used in the working environment to the new technological paradigm so that the industry is connected and, at the same time, workers are as safe and protected as possible. Thanks to Smart Personal Protective Equipment (PPE) and wearable technologies, information about the workers and their environment can be extracted to reduce the rate of accidents and occupational illness, leading to a significant improvement. This article proposes an architecture that employs three pieces of PPE: a helmet, a bracelet and a belt, which process the collected information using artificial intelligence (AI) techniques through edge computing. The proposed system guarantees the workers' safety and integrity through the early prediction and notification of anomalies detected in their environment. Models such as convolutional neural networks, long short-term memory, Gaussian Models were joined by interpreting the information with a graph, where different heuristics were used to weight the outputs as a whole, where finally a support vector machine weighted the votes of the models with an area under the curve of 0.81.

Smart Helmet 5.0 for Industrial Internet of Things Using Artificial Intelligence.

Information and communication technologies (ICTs) have contributed to advances in Occupational Health and Safety, improving the security of workers. The use of Personal Protective Equipment (PPE) based on ICTs reduces the risk of accidents in the workplace, thanks to the capacity of the equipment to make decisions on the basis of environmental factors. Paradigms such as the Industrial Internet of Things (IIoT) and Artificial Intelligence (AI) make it possible to generate PPE models feasibly and create devices with more advanced characteristics such as monitoring, sensing the environment and risk detection between others. The working environment is monitored continuously by these models and they notify the employees and their supervisors of any anomalies and threats. This paper presents a smart helmet prototype that monitors the conditions in the workers' environment and performs a near real-time evaluation of risks. The data collected by sensors is sent to an AI-driven platform for analysis. The training dataset consisted of 11,755 samples and 12 different scenarios. As part of this research, a comparative study of the state-of-the-art models of supervised learning is carried out. Moreover, the use of a Deep Convolutional Neural Network (ConvNet/CNN) is proposed for the detection of possible occupational risks. The data are processed to make them suitable for the CNN and the results are compared against a Static Neural Network (NN), Naive Bayes Classifier (NB) and Support Vector Machine (SVM), where the CNN had an accuracy of 92.05% in cross-validation.

SMART-LAMP: A Smartphone-Operated Handheld Device for Real-Time Colorimetric Point-of-Care Diagnosis of Infectious Diseases via Loop-Mediated Isothermal Amplification.

Nucleic acid amplification diagnostics offer outstanding features of sensitivity and specificity. However, they still lack speed and robustness, require extensive infrastructure, and are neither affordable nor user-friendly. Thus, they have not been extensively applied in point-of-care diagnostics, particularly in low-resource settings. In this work, we have combined the loop-mediated isothermal amplification (LAMP) technology with a handheld portable device (SMART-LAMP) developed to perform real-time isothermal nucleic acid amplification reactions, based on simple colorimetric measurements, all of which are Bluetooth-controlled by a dedicated smartphone app. We have validated its diagnostic utility regarding different infectious diseases, including Schistosomiasis, Strongyloidiasis, and COVID-19, and analyzed clinical samples from suspected COVID-19 patients. Finally, we have proved that the combination of long-term stabilized LAMP master mixes, stored and transported at room temperature with our developed SMART-LAMP device, provides an improvement towards true point-of-care diagnosis of infectious diseases in settings with limited infrastructure. Our proposal could be easily adapted to the diagnosis of other infectious diseases.