Influence of mileage accumulation on the particle mass and number emissions of two gasoline direct injection vehicles.

Gasoline direct injection (GDI) is a new engine technology intended to improve fuel economy and greenhouse gas emissions as required by recently enacted legislative and environmental regulations. The development of this technology must also ensure that these vehicles meet new LEV III and Tier 3 emissions standards as they phase in between 2017 and 2021. The aim of the present paper is to examine, at least for a small set, how the PM emissions from GDI vehicles change over their lifetime. The paper reports particle mass and number emissions of two GDI vehicles as a function of mileage up to 150K miles. These vehicles exhibit PM emissions that are near or below the upcoming 3 mg/mi FTP and 10 mg/mi US06 mass standards with little, if any, deterioration over 150K miles. Particle number emissions roughly follow the previously observed 2 × 10(12) particles/mg correlation between solid particle number and PM mass. They remained between the interim and final EU stage 6 solid particle count standard for gasoline vehicles throughout the mileage accumulation study. These examples demonstrate feasibility to meet near-term 3 mg/mi and interim EU solid particle number standards, but continued development is needed to ensure that this continues as further fuel economy improvements are made.

Primary gas- and particle-phase emissions and secondary organic aerosol production from gasoline and diesel off-road engines.

Dilution and smog chamber experiments were performed to characterize the primary emissions and secondary organic aerosol (SOA) formation from gasoline and diesel small off-road engines (SOREs). These engines are high emitters of primary gas- and particle-phase pollutants relative to their fuel consumption. Two- and 4-stroke gasoline SOREs emit much more (up to 3 orders of magnitude more) nonmethane organic gases (NMOGs), primary PM and organic carbon than newer on-road gasoline vehicles (per kg of fuel burned). The primary emissions from a diesel transportation refrigeration unit were similar to those of older, uncontrolled diesel engines used in on-road vehicles (e.g., premodel year 2007 heavy-duty diesel trucks). Two-strokes emitted the largest fractional (and absolute) amount of SOA precursors compared to diesel and 4-stroke gasoline SOREs; however, 35-80% of the NMOG emissions from the engines could not be speciated using traditional gas chromatography or high-performance liquid chromatography. After 3 h of photo-oxidation in a smog chamber, dilute emissions from both 2- and 4-stroke gasoline SOREs produced large amounts of semivolatile SOA. The effective SOA yield (defined as the ratio of SOA mass to estimated mass of reacted precursors) was 2-4% for 2- and 4-stroke SOREs, which is comparable to yields from dilute exhaust from older passenger cars and unburned gasoline. This suggests that much of the SOA production was due to unburned fuel and/or lubrication oil. The total PM contribution of different mobile source categories to the ambient PM burden was calculated by combining primary emission, SOA production and fuel consumption data. Relative to their fuel consumption, SOREs are disproportionately high total PM sources; however, the vastly greater fuel consumption of on-road vehicles renders them (on-road vehicles) the dominant mobile source of ambient PM in the Los Angeles area.

Engine, aftertreatment, fuel quality and non-tailpipe achievements to lower gasoline vehicle PM emissions: Literature review and future prospects.

Spark ignition gasoline vehicles comprise most light duty vehicles worldwide. These vehicles were not historically associated with PM emissions. This changed about 15 years ago when emissions regulations forced diesel engines to employ exhaust particulate filters and fuel economy requirements ushered in gasoline direct injection (GDI) technology. These shifts reversed the roles of gasoline and diesel vehicles, with GDI vehicles now regarded as the high PM emitters. Regulators worldwide responded with new or revised PM emissions standards. This review takes a comprehensive look at PM emissions from gasoline vehicles. It examines the technological advances that made it possible for GDI vehicles to meet even the most stringent tailpipe PM standards. These include fuel injection strategies and injector designs to limit fuel films in the engine cylinder that were pathways for soot formation and the development of gasoline particle filters to remove PM from engine exhaust. The review also examines non-exhaust PM emissions from brake, tire, and road wear, which have become the dominant sources of vehicle derived PM. Understanding the low levels of GDI tailpipe PM emissions that have been achieved and its contribution to total vehicle PM emissions is essential for the current debate about the future of internal combustion engines versus rapidly evolving battery electric vehicles. In this context, it does not make sense to consider BEVs as zero emitting vehicles. Rather, a more holistic framework is needed to compare the relative merits of various vehicle powertrains.

Directions for combustion engine aerosol measurement in the 21st century.

The Coordinating Research Council convened two Real-Time PM Measurement Workshops in December 2008 and March 2009 to take an intensive look at the current status and future directions of combustion aerosol measurement. The purpose was to examine the implications of parallel rapid developments over the past decade in ambient aerosol science, engine aftertreatment technology, and aerosol measurement methodology, which provide benefits and challenges to the stakeholders in air quality management. The workshops were organized into sessions targeting key issues in ambient and source combustion particulate matter (PM). These include (1) metrics to characterize and quantify PM, (2) the need to reconcile ambient and source measurements, (3) the role of atmospheric transformations on modeling emissions and exposures, (4) the impact of sampling conditions on PM measurement, and (5) the potential benefits of novel PM instrumentation. This paper distills the material presented by subject experts and the insights derived from the in-depth discussions that formed the core of each session. The paper's objectives are to identify areas of consensus that allow wider practical application of the past decade's advances in combustion aerosol measurement to improve emissions and air quality modeling, develop emissions reduction strategies, and to recommend directions for progress on issues in which uncertainties remain.

The effects of water vapor on the CH3O2 self-reaction and reaction with HO2.

The gas phase reactions of CH3O2 + CH3O2, HO2 + HO2, and CH3O2 + HO2 in the presence of water vapor have been studied at temperatures between 263 and 303 K using laser flash photolysis coupled with UV time-resolved absorption detection at 220 and 260 nm. Water vapor concentrations were quantified using tunable diode laser spectroscopy operating in the mid-IR. The HO2 self-reaction rate constant is significantly enhanced by water vapor, consistent with what others have reported, whereas the CH3O2 self-reaction and the cross-reaction (CH3O2 + HO2) rate constants are nearly unaffected. The enhancement in the HO2 self-reaction rate coefficient occurs because of the formation of a strongly bound (6.9 kcal mol(-1)) HO2 x H2O complex during the reaction mechanism where the H2O acts as an energy chaperone. The nominal impact of water vapor on the CH3O2 self-reaction rate coefficient is consistent with recent high level ab initio calculations that predict a weakly bound CH3O2 x H2O complex (2.3 kcal mol(-1)). The smaller binding energy of the CH3O2 x H2O complex does not favor its formation and consequent participation in the methyl peroxy self-reaction mechanism.

A constant-volume rapid exhaust dilution system for motor vehicle particulate matter number and mass measurements.

An improved version of the constant volume sampling (CVS) methodology that overcomes a number of obstacles that exist with the current CVS dilution tunnel system used in most diesel and gasoline vehicle emissions test facilities is presented. The key feature of the new sampling system is the introduction of dilution air immediately at the vehicle tailpipe. In the present implementation, this is done concentrically through a cylindrical air filter. Elimination of the transfer hose conventionally used to connect the tailpipe to the dilution tunnel significantly reduces the hydrocarbon and particulate matter (PM) storage release artifacts that can lead to wildly incorrect particle number counts and to erroneous filter-collected PM mass. It provides accurate representations of particle size distributions for diesel vehicles by avoiding the particle coagulation that occurs in the transfer hose. Furthermore, it removes the variable delay time that otherwise exists between the time that emissions exit the tailpipe and when they are detected in the dilution tunnel. The performance of the improved CVS system is examined with respect to diesel, gasoline, and compressed natural gas vehicles.

Diesel nucleation mode particles: semivolatile or solid?

Although the preponderance of current data points to semivolatile diesel nuclei particles composed of sulfuric acid and heavy hydrocarbons, the question remains as to what extent, if any, they contain solid cores. We present evidence here of a "solid" particle nucleation mode that accompanies normal soot emissions in the case of two modern light-duty diesel vehicles run with ultralow sulfur fuel. This mode is most prominent at idle, but also appears at speeds below approximately 30 mph, and is highly sensitive to the level of exhaust gas recirculation (EGR). The nuclei particles are examined for their volatility and electrical charge. In stark contrast to "conventional" nuclei particles, they remain nonvolatile to >400 degrees C and exhibit a bipolar charge with a Boltzmann temperature of 580 degrees C. Their nonvolatile nature rules out sulfate and heavy hydrocarbons as primary constituents, and their electrical charge requires formation in a high-temperature environment capable of generating bipolar ions. This suggests that "solid" nuclei particles form during combustion but remain distinct from soot particles, analogous to what has been found recently in flames. As concerns about potential emissions of nonvolatile nanoparticles have already surfaced, an important conclusion of this study is that diesel particulate filters remove the "solid" nucleation mode with an efficiency comparable to soot

Dimethyl ether oxidation at elevated temperatures (295-600 K).

Dimethyl ether (DME) has been proposed for use as an alternative fuel or additive in diesel engines and as a potential fuel in solid oxide fuel cells. The oxidation chemistry of DME is a key element in understanding its role in these applications. The reaction between methoxymethyl radicals and O(2) has been examined over the temperature range 295-600 K and at pressures of 20-200 Torr. This reaction has two product pathways. The first produces methoxymethyl peroxy radicals, while the second produces OH radicals and formaldehyde molecules. Real-time kinetic measurements are made by transient infrared spectroscopy to monitor the yield of three main products-formaldehyde, methyl formate, and formic acid-to determine the branching ratio for the CH(3)OCH(2) + O(2) reaction pathways. The temperature and pressure dependence of this reaction is described by a Lindemann and Arrhenius mechanism. The branching ratio is described by f = 1/(1 + A(T)[M]), where A(T) = (1.6(+2.4)(-1.0) x 10(-20)) exp((1800 +/- 400)/T) cm(3) molecule(-1). The temperature dependent rate constant of the methoxymethyl peroxy radical self-reaction is calculated from the kinetics of the formaldehyde and methyl formate product yields, k(4) = (3.0 +/- 2.1) x 10(-13) exp((700 +/- 250)/T) cm(3) molecule(-1) s(-1). The experimental and kinetics modeling results support a strong preference for the thermal decomposition of alkoxy radicals versus their reaction with O(2) under our laboratory conditions. These characteristics of DME oxidation with respect to temperature and pressure might provide insight into optimizing solid oxide fuel cell operating conditions with DME in the presence of O(2) to maximize power outputs.

Airborne brake wear debris: size distributions, composition, and a comparison of dynamometer and vehicle tests.

Particle size distributions of light-duty vehicle brake wear debris are reported with careful attention paid to avoid sampling biases. Electrical low-pressure impactor and micro-orifice uniform deposit impactor measurements yield consistent size distributions, and the net particulate matter mass from each method is in good agreement with gravimetric filter measurements. The mass mean diameter of wear debris from braking events representative of urban driving is 6 microm, and the number-weighted mean is 1-2 microm for three currently used classes of lining materials: low metallic, semimetallic, and non-asbestos organic (NAO). In contrast, the wear rates are very material dependent, both in number and mass of particles, with 3-4 times higher emissions observed from the low metallic linings as compared to the semimetallic and NAO linings. Wind tunnel and test track measurements demonstrate the appearance of micron size particles that correlate with braking events, with approximately 50% of the wear debris being airborne for the test vehicle in this study. Elemental analysis of the wear debris reveals a consistent presence of the elements Fe, Cu, and Ba in both dynamometer and test track samples.

The effects of the catalytic converter and fuel sulfur level on motor vehicle particulate matter emissions: gasoline vehicles.

Scanning mobility and electrical low-pressure impactor particle size measurements conducted during chassis dynamometer testing reveal that neither the catalytic converter nor the fuel sulfur content has a significant effect on gasoline vehicle tailpipe particulate matter (PM) emissions. For current technology, port fuel injection, gasoline engines, particle number emissions are < or = 2 times higher from vehicles equipped with blank monoliths as compared to active catalysts, insignificant in contrast to the 90+% removal of hydrocarbons. PM mass emission rates derived from the size distributions are equal within the experimental uncertainty of 50-100%. Gravimetric measurements exhibit a 3-10-fold PM mass increase when the active catalyst is omitted, which is attributed to gaseous hydrocarbons adsorbing onto the filter medium. Both particle number and gravimetric measurements show that gasoline vehicle tailpipe PM emissions are independent (within 2 mg/mi) of fuel sulfur content over the 30-990 ppm concentration range. Nuclei mode sulfate aerosol is not observed in either test cell measurements or during wind tunnel testing. For three-way catalyst equipped vehicles, the principal sulfur emission is SO2; however a sulfur balance is not obtained over the drive cycle. Instead, sulfur is stored on the catalyst during moderate driving and then partially removed during high speed/load operation.

The effects of the catalytic converter and fuel sulfur level on motor vehicle particulate matter emissions: light duty diesel vehicles.

Wind tunnel measurements and direct tailpipe particulate matter (PM) sampling are utilized to examine how the combination of oxidation catalyst and fuel sulfur content affects the nature and quantity of PM emissions from the exhaust of a light duty diesel truck. When low sulfur fuel (4 ppm) is used, or when high sulfur (350 ppm)fuel is employed without an active catalyst present, a single log-normal distribution of exhaust particles is observed with a number mean diameter in the range of 70-83 nm. In the absence of the oxidation catalyst, the high sulfur level has at most a modest effect on particle emissions (<50%) and a minor effect on particle size (<5%). In combination with the active oxidation catalyst tested, high sulfur fuel can lead to a second, nanoparticle, mode, which appears at approximately 20 nm during high speed operation (70 mph), but is not present at low speed (40 mph). A thermodenuder significantly reduces the nanoparticle mode when set to temperatures above approximately 200 degrees C, suggesting that these particles are semivolatile in nature. Because they are observed only when the catalyst is present and the sulfur level is high, this mode likely originates from the nucleation of sulfates formed over the catalyst, although the composition may also include hydrocarbons.