RESUMO
The detection of cholesterol is very crucial in clinical diagnosis for rapid and accurate monitoring of multiple disease-biomarkers. There is a great need for construction of a highly reliable and stable electrocatalyst for the efficient detection of cholesterol. In this work, mesoporous NiCo2S4nanoflakes of enhanced electrochemical properties are prepared through a facile hydrothermal approach. The developed nanoflakes modified nickel foam electrode exhibits outstanding electrocatalytic properties for the detection of cholesterol with high selectivity. The electrode displays excellent sensitivity of 8623.6µA mM-1cm-2, in the wide linear range from 0.01 to 0.25 mM with a low detection limit of 0.01µM. In addition, NiCo2S4structure reveals good thermal stability and reproducibility over a period of 8 weeks. Moreover, the nanoflakes show good response for detection of cholesterol in real samples. Our results demonstrate the potential use of NiCo2S4as a catalyst for the development of cost-effective electrochemical sensors for medical and industrial applications.
Assuntos
Técnicas Eletroquímicas , Níquel , Colesterol , Técnicas Eletroquímicas/métodos , Eletrodos , Níquel/química , Reprodutibilidade dos TestesRESUMO
Cobalt-doped zinc ferrite is a contemporary material with significant structural and magnetic characteristics. Our study explores the magnetic properties of cobalt-substituted zinc ferrite (ZnxCo1-xFe2O4), synthesized via a simple sol-gel method. By varying the cobalt ratio from 0 to 0.5, we found that zinc substitution impacts both the magnetization and lattice parameters. FTIR analysis suggested the presence of functional groups, particularly depicting an M-O stretching band, within octahedral and tetrahedral clusters. X-ray diffraction analysis confirmed the phase purity and cubic structure. The synthesized materials exhibited an average particle size of 24-75 nm. Scanning electron microscopy revealed the morphological properties, confirming the formation of truncated octahedral particles. In order to determine the stability, mass loss (%), and thermal behavior, a thermal analysis (thermogravimetric analysis (TGA)/differential thermal analysis (DTA)) was performed. The magnetic properties of the synthesized ferrites were confirmed via a vibrating sample magnetometer (VSM). Finally, the highest saturated magnetization and lowest coercivity values were observed with higher concentrations of the cobalt dopant substituting zinc. The synthesized nanomaterials have good stability as compared to other such materials and can be used for magnetization in the near future.
RESUMO
In this work, the new compositions of FeCoNiAlMn1-xCrx, (0.0 ≤ x ≤ 1.0), a high-entropy alloy powder (HEAP), are prepared by mechanical alloying (MA). The influence of Cr doping on the phase structure, microstructure, and magnetic properties is thoroughly investigated through X-ray diffraction (XRD), scanning electron microscopy (SEM), and vibrating sample magnetometry. It is found that this alloy has formed a simple body-centered cubic structure with a minute face-centered cubic structure for Mn to Cr replacement with heat treatment. The lattice parameter, average crystallite size, and grain size decrease by replacing Cr with Mn. The SEM analysis of FeCoNiAlMn showed no grain boundary formation, depicting a single-phase microstructure after MA, similar to XRD. The saturation magnetization first increases (68 emu/g) up to x = 0.6 and then decreases with complete substitution of Cr. Magnetic properties are related to crystallite size. FeCoNiAlMn0.4Cr0.6 HEAP has shown optimum results with better saturation magnetization and coercivity as a soft magnet.
RESUMO
In current work, pure ZnO and Zn0.96-x Cu0.04Co x O (0 ≤ x ≤ 0.05) nanoparticles were synthesized by the co-precipitation method. Structural analysis and phase determination of the formed nanoparticles was carried out using X-ray diffraction (XRD) and Williamson-Hall plots. The hexagonal wurtzite structure was manifested by all the samples with divergent microstructures. The change in lattice parameters, bond length, dislocation density, and lattice strain indicates that Cu and Co were successfully incorporated. Average crystallite size was found to be in the range of 32.16-45.42 nm for various doping concentrations. Field emission scanning electron microscopy results exhibited that the surface morphology is an amalgam of spherical-like and hexagon-like structures. Spherical-shaped grains were homogeneous and evenly distributed all over the structure. Fourier transform infrared spectra indicated that the absorption bands were blue-shifted with increasing Co concentration. The UV-visible absorption spectra showed high absorption in the UV region and weak absorption in the visible region. An increase in the energy band gap for the maximum absorption peak was observed from 3.49 eV for ZnO to 3.88 eV for Zn0.91Cu0.04Co0.05O. The Burstein-Moss effect explained the noticed blue shift in absorption spectra and energy band gaps. The vibrating sample magnetometer study revealed the change in the diamagnetic behavior of pure ZnO to the ferromagnetic behavior of the prepared nanoparticles at room temperature for different doping concentrations. In the current study, we have developed the room-temperature ferromagnetism (RTFM) for Cu and Co co-doped ZnO nanoparticles. Since RTFM is the key objective for dilute magnetic semiconductors, therefore it can be served as the desirable expectant for spintronics applications with improved functionalities and device concepts.
RESUMO
Multilayer CdZnS (CZS) thin film was deposited on soda lime glass substrates. After deposition, the films were vacuum and air annealed at 100 °C, 200 °C, 300 and 400 °C for 1 h. Effects of vacuum and air annealing on structural, morphological, optical, and electrical properties of multilayer CZS films with increasing annealing temperature (IAT) were studied. The structural analysis revealed that the films were polycrystalline with hexagonal structure having a prominent/intensive peak along the (002) plane at 300 and 400 °C. The crystallite size of nanoparticles increased from 18.4 to 20.5 nm under air annealing and from 18.4 to 26.9 nm under vacuum annealing, showing the significance of annealing on nanoparticle grain growth. According to morphological analysis, the multilayer technique provides homogeneous film distribution over the substrate. The transmittance graphs of films revealed that it increased up to 92% in the visible and NIR regions under vacuum annealing and up to 52% under air annealing. Vacuum annealing enhanced the band gap energies more significantly than air annealing. The electrical resistivity increased with IAT, showing that structural, morphological, optical, and electrical properties of the multilayer thin films of CZS were strongly dependent on vacuum and air annealing.
RESUMO
The lead-free Ca(Sn x Ti1-x )O3, (0 ≤ x ≤ 0.8) sample has been successfully prepared through the ball milling process, sintered at 1200 °C for 3 h. The structural, morphological, vibrational, and microwave dielectric properties of synthesized samples were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), and impedance analysis. All the samples have an orthorhombic phase structure with a space group of Pbnm formation, and the crystalline size and strain changes with respect to Sn4+ doping were observed in the XRD analysis. From a morphological point of view, on increasing the content "x", the grain size reduces from 3.29 to 1.37 µm. The existence of vibrations and the bridging stretching mode of Ti-O-Ti and Ti-O-Sn both are associated with the broadband in the region below 800 cm-1 verified by FT-IR. The variation in electrons hopping off the host compound with respect to Sn4+ ions was analyzed in AC conductivity. The changes of dielectric properties such as complex permittivity, modulus spectroscopy, and dielectric loss at room temperature with a different frequency range of 1.00-2.00 GHz are discussed.
RESUMO
Thin films of Cd1-xMgxO (CdMgO) (0 ≤ x ≤ 1) were investigated by depositing the films on glass substrates using the co-evaporation technique. The structural, surface morphological, optical, and electrical characteristics of these films were studied as a function of Mg content after annealing at 350 °C. The XRD analysis showed that the deposited films had an amorphous nature. The grain size of the films reduced as the Mg concentration increased, as evidenced by the surface morphology, and EDAX supported the existence of Mg content. It was observed that as the films were annealed, the transmittance of the CdMgO films saw an increase of up to 85%. The blue shift of the absorption edge was observed by the increase of Mg content, which was useful for enhancing the efficiency of solar cells. The optical band gap increased from 2.45 to 6.02 eV as the Mg content increased. With increased Mg content, the refractive index reduced from 2.49 to 1.735, and electrical resistivity increased from 535 Ω cm to 1.57 × 106 Ω cm.
RESUMO
This work reports synthesis, thin film characterizations, and study of an organic semiconductor 2-aminoanthraquinone (AAq) for humidity and temperature sensing applications. The morphological and phase studies of AAq thin films are carried out by scanning electron microscope (SEM), atomic force microscope (AFM), and X-ray diffraction (XRD) analysis. To study the sensing properties of AAq, a surface type Au/AAq/Au sensor is fabricated by thermally depositing a 60 nm layer of AAq at a pressure of ~10-5 mbar on a pre-patterned gold (Au) electrodes with inter-electrode gap of 45 µm. To measure sensing capability of the Au/AAq/Au device, the variations in its capacitance and resistance are studied as a function of humidity and temperature. The Au/AAq/Au device measures and exhibits a linear change in capacitance and resistance when relative humidity (%RH) and temperature are varied. The AAq is a hydrophobic material which makes it one of the best candidates to be used as an active material in humidity sensors; on the other hand, its high melting point (575 K) is another appealing property that enables it for its potential applications in temperature sensors.