Nanomaterials in Cementitious Composites: An Update.

This review is an update about the addition of nanomaterials in cementitious composites in order to improve their performance. The most common used nanomaterials for cementitious materials are carbon nanotubes, nanocellulose, nanographene, graphene oxide, nanosilica and nanoTiO2. All these nanomaterials can improve the physical, mechanical, thermal and electrical properties of cementitious composites, for example increase their compressive and tensile strength, accelerate hydration, decrease porosity and enhance fire resistance. Cement based materials have a very complex nanostructure consisting of hydration products, crystals, unhydrated cement particles and nanoporosity where traditional reinforcement, which is at the macro and micro scale, is not effective. Nanomaterials can reinforce the nanoscale, which wasn't possible heretofore, enhancing the performance of the cementitious matrix.

The effect of nanobubbles on Langmuir-Blodgett films.

Nanobubbles (NBs) are classified in two distinct categories: surface and bulk. Surface NBs are readily observed using atomic force microscopy (AFM), while the existence of bulk NBs has been a subject of debate, conflicting with the diffusion theory's predictions. Current methodologies for identifying bulk NBs yield inconclusive results. In this study, Langmuir Blodgett (LB) technique and AFM, are utilized to visualize NB imprints on anionic, cationic and zwitterionic lipid films deposited on glass-slide substrates. Our analysis of Langmuir monolayers compression isotherms reveals the impact of bulk NBs on lipid monolayer development. AFM scans of the deposited lipid films consistently show NB imprints. Notably, cationic and zwitterionic film depositions exhibit NB formations from the 1st layer, whereas in anionic films, these formations are observed only after the 3rd layer. These results suggest that the origin of these imprinted formations may be attributed to bulk NBs.

Electrochemical Impedance as an Assessment Tool for the Investigation of the Physical and Mechanical Properties of Graphene-Based Cementitious Nanocomposites.

This investigation explores the potential of electrochemical impedance spectroscopy (EIS) in evaluating graphene-based cementitious nanocomposites, focusing on their physical and structural properties, i.e., electrical resistivity, porosity, and fracture toughness. EIS was employed to study cement mixtures with varying graphene nanoplatelet (xGnP) concentrations (0.05-0.40% per dry cement weight), whereas flexural tests assessed fracture toughness and porosimetry analyses investigated the structural characteristics. The research demonstrated that the electrical resistivity initially decreased with increasing xGnP content, leveling off at higher concentrations. The inclusion of xGnPs correlated with an increase in the total porosity of the cement mixtures, which was indicated by both EIS and porosimetry measurements. Finally, a linear correlation emerged between fracture toughness and electrical resistivity, contributing also to underscore the use of EIS as a potent non-destructive tool for evaluating the physical and mechanical properties of conductive nano-reinforced cementitious nanocomposites.

Dispersion of Multi-Walled Carbon Nanotubes into White Cement Mortars: The Effect of Concentration and Surfactants.

Multi-wall carbon nanotubes (MWCNTs) exhibit exceptional mechanical and electrical properties and can be used to improve the mechanical and piezoelectric properties of cement-based materials. In the present study, the effect of different MWCNT concentrations as well as different types of surfactants and a superplasticizer were examined to reinforce, at the nanoscale, a white cement mortar typically used for the restoration of monuments of cultural heritage. It was shown that sodium dodecylbenzenesulfonate (SDBS) and Triton X-100 surfactants slightly decreased the white cement mortars' electrical resistivity (by an average of 10%), however, the mechanical properties were essentially decreased by an average of 60%. The most suitable dispersion agent for the MWCNTs proved to be the superplasticizer Ceresit CC198, and its optimal concentration was investigated for different MWCNT concentrations. Carboxylation of the MWCNT surface with nitric acid did not improve the mechanical performance of the white cement nanocomposites. The parametric experimental study showed that the optimum combination of 0.8 wt% of cement superplasticizer and 0.2 wt% of cement MWCNTs resulted in a 60% decrease in the electrical resistivity; additionally, the flexural and compressive strengths were both increased by approximately 25% and 10%, respectively.

Piezoresistive Properties of Natural Hydraulic Lime Binary Pastes with Incorporated Carbon-Based Nanomaterials under Cyclic Compressive Loadings.

Natural Hydraulic Limes (NHL) are extensively used for the restoration of Monuments of Cultural Heritage, often combined with pozzolanic materials, such as natural pozzolans and metakaolin etc. In the present study, five (5) different cases of binary lime-based pastes composed of a specific type of NHL (NHL5) and metakaolin as pozzolanic addition were examined, that were reinforced with carbon nanostructures, namely graphene and carbon nanotubes. For the first time in restoration mortars, the incorporation of carbon nanostructures was investigated, aiming to produce materials with adequate piezoresistive response, so that they have the potential to be exploited for in situ structural health monitoring. The compressive strength, flexural strength, electrical resistance and piezoresistive response of the composite pastes was examined. The results showed that all modified carbon nanostructures lead to a significant reduction in electrical resistance. The pastes reinforced with 2D nanostructures (graphene family) displayed up to 30% increase in compressive strength and the pastes reinforced with 1D nanostructures (carbon nanotubes) displayed enhanced flexural strength (up to 100% increase). Piezoresistivity was attained for almost all investigated pastes, nevertheless the graphene oxide (GO) was considered as optimal reinforcement as the sensing ability of such pastes was found to be almost proportional to the applied compressive load level.

Cement Composites with Graphene Nanoplatelets and Recycled Milled Carbon Fibers Dispersed in Air Nanobubble Water.

The individual effect of nano- and micro-carbon-based fillers on the mechanical and the electrical properties of cement paste were experimentally examined in this study. The objective of the study was to separately examine the effects of size and morphology (platelets and fibers) of nano- and micro-reinforcement. Three different sizes of Graphene Nanoplatelets (GNPs), at contents of 0.05% and 0.20% and recycled milled carbon fibers (rCFs), at various dosages from 0.1-2.5% by weight of cement, were incorporated into the cementitious matrix. GNPs and rCFs were dispersed in water with air nanobubbles (NBs), an innovative method that, compared to common practice, does not require the use of chemicals or high ultrasonic energy. Compressive and bending tests were performed on GNPs- and rCFs-composites. The four-wire-method was used to evaluate the effect of the conductive fillers on the electrical resistivity of cement paste. The compressive and flexural strength of all the cementitious composites demonstrated a considerable increase compared to the reference specimens. Improvement of 269.5% and of 169% was observed at the compressive and flexural strength, respectively, at the GNPs-cement composites incorporating the largest lateral size GNPs at a concentration of 0.2% by weight of cement. Moreover, the rCFs-cement composites increased their compressive and flexural strength by 186% and 210%, respectively, compared to the reference specimens. The electrical resistivity of GNPs- and rCFs-composite specimens reduced up to 59% and 48%, respectively, compared to the reference specimens, which proves that the incorporation of GNPs and rCFs can create a conductive network within the cementitious matrix.

Bartonella henselae Infection: An Uncommon Mimicker of Autoimmune Disease.

We present a case of a seven-year-old immunocompetent female patient who developed systemic symptoms mimicking an autoimmune rather than an infectious disease. The patient presented with rash, biquotidian fever, night sweats, and arthralgias. There was no antecedent history of cat contact. Investigations showed increased inflammatory markers, leukocytosis, thrombocytosis, hypercalcemia, and raised angiotensin-converting enzyme. Interferon-gamma releasing assay for tuberculosis infection was negative. Abdominal imaging demonstrated multifocal lesions of the liver and spleen (later proved to be granulomata), chest X-ray showed enlarged hilar lymph nodes, and ophthalmology review revealed uveitis. Clinical, laboratory, and imaging features pointed towards sarcoidosis. Subsequently, raised titers (IgM 1 : 32, IgG 1 : 256) against Bartonella confirmed the diagnosis of B. henselae infection. She was treated with gentamycin followed by ciprofloxacin; repeat investigations showed complete resolution of findings. The presence of hepatic and splenic lesions in children with bartonellosis is well documented. Our case, however, exhibited certain unusual findings such as the coexistence of acute ocular and systemic involvement in an immunocompetent host. Serological testing is an inexpensive and effective way to diagnose bartonellosis in immunocompetent patients; we suggest that bartonella serology is included in the baseline tests performed on children with prolonged fever even in the absence of contact with cats in countries where bartonellosis is prevalent.