Misophonia in Children and Adolescents: Age Differences, Risk Factors, Psychiatric and Psychological Correlates. A Pilot Study with Mothers' Involvement.

Misophonia is a type of disorder characterized by decreased sound tolerance. While it typically begins in childhood, research on its characteristics in this population is limited. We assessed 90 children aged 7-18 with and without misophonia, along with their mothers, using interviews, questionnaires, and performance-based tests. Younger children with misophonia were more likely to use aggression in response to triggers than older, while adolescents largely reported self-harm during triggers. Children with misophonia did not differ from their peers in terms of ADHD, ODD, ASD, dyslexia, social and emotional competencies, head injuries, epilepsy, tinnitus, being prematurely born, or delivered via cesarean sections. However, they had significantly higher symptoms of anxiety and depression, more frequent occurrences of OCD, migraines, and psychosomatic complaints. Their mothers self-reported postpartum depression significantly more frequently than mothers in the control group. There is a need for further research on pediatric misophonia, with the involvement and assessment of parents.

Effect of the Technological Parameters of Milling on Residual Stress in the Surface Layer of Thin-Walled Plates.

The production of thin-walled elements, especially those with large overall dimensions, poses numerous technological and operational problems. One of these problems relates to the machining-induced strain of such elements resulting from residual stress generated during the machining process. This study investigates the effect of the technological parameters of milling on residual stress in the surface layer of thin-walled plates made of aluminum alloy EN AW-2024 T351 for aerospace applications. The results have shown that residual stress increases with the cutting speed only to a certain point, reaching the maximum value at vc = 750 m/min. At a cutting speed vc = 900 m/min, residual stress significantly decreases, which probably results from the fact that the milling process has entered the High-Speed Cutting range, and this inference agrees with the results obtained for the cutting force component. Residual stress increases with the feed per tooth, while the relationship between residual stress and milling width is the same as that established for residual stress and variable cutting speed. Positive tensile stress is obtained in every tested case of the milling process. The results have also shown that the induced residual stress affects the strain of machined thin-walled parts, as proved by the strain results obtained for milled thin walls.

Exposure to self-reported traumatic events and probable PTSD in a national sample of Poles: Why does Poland's PTSD prevalence differ from other national estimates?

BACKGROUND: There is a lack of studies on trauma exposure and PTSD prevalence in Poland on representative samples. Available data from studies on convenient samples show very high rates of probable PTSD compared with relevant estimates in other countries. OBJECTIVE: This study aimed to measure the exposure to self-report traumatic events (PTEs) and to estimate the current rate of prevalence of probable posttraumatic stress disorder (PTSD) in accordance with DSM-5 criteria in a population-based sample of Poles. Additionally, the link between PTSD intensity and level of life satisfaction was investigated. METHOD: A representative sample of 1,598 adult Poles was recruited. Probable PTSD was assessed with the Posttraumatic Diagnostic Scale for DSM-5 (PDS-5) and the Satisfaction with Life Scale (SWLS) was also used. RESULTS: The findings showed that 60.3% of Poles had experienced at least one PTE and 31.1% of those who had been exposed to trauma reported symptoms of PTSD. At the level of the entire sample, the obtained rate for probable PTSD was 18.8%. The traumatic events with the highest probabilities of PTSD symptoms were child abuse and sexual assault. Levels of life satisfaction were significantly lower in the group of participants with probable PTSD. CONCLUSIONS: We found that the current prevalence of probable PTSD in Poland is intriguingly high relative to rates reported in comparable representative samples from other countries across the world. Possible mechanisms are discussed, including a lack of social acknowledgement of WWII and other traumas as well as poor access to trauma-focused care. We hope that this research may inspire more studies investigating cross-national differences in PTSD and trauma exposure.

Long-lasting effects of World War II trauma on PTSD symptoms and embodiment levels in a national sample of Poles.

The main aim of this study was to investigate the long-lasting influences of World War II (WWII) trauma in a national sample of Poles, based on Danieli's (1998) survivors' post-trauma adaptational styles (fighter, numb, victim) and their link with current post-traumatic stress disorder (PTSD) symptoms and embodiment level among participants. We also sought to investigate whether the level of knowledge about WWII trauma among ancestors could moderate that association. The study was conducted among a representative sample of 1598 adult Poles obtained from an external company. Participants filled out the Danieli Inventory of Multigenerational Legacies of Trauma, the knowledge about traumatic World War II experiences in the family questionnaire, the Posttraumatic Diagnostic Scale-5, and the Experience of Embodiment Scale. We observed a positive relationship between all survivors' post-trauma adaptational styles and current levels of PTSD symptoms among participants. In addition, PTSD level mediated the relationships between those adaptational styles and embodiment intensity; that mediation was additionally moderated by a lack of knowledge about WWII trauma among ancestors in our participants. Our study adds to the literature on intergenerational trauma by highlighting the importance of evaluating embodiment in understanding the mechanisms of trauma transmission. Furthermore, it highlights the moderating effect of knowledge of family history in this mechanism and the need to share family histories with subsequent generations.

Effect of the Geometry of Thin-Walled Aluminium Alloy Elements on Their Deformations after Milling.

The aim of this paper is to analyse the effect of the selected geometric properties of thin-walled structures on post-machining deformations. In the study, EN AW-7075 T651 and EN AW-6082 T651 aluminium alloys were used to prepare specially designed thin-walled sample elements, i.e., elements with walls arranged in a semi-open and closed structure and with a dimension of 165 × 262 × 50.8 mm consisting of bottom and vertical stiffening walls and so-called ribs with a thickness of 1 mm. The measurements of the absolute deformations of the thin-walled bottom were performed with the use of a Vista coordinate-measuring machine by Zeiss with a PH10 head by Renishaw. Based on the obtained results, it was found that absolute deformation values were higher for walls arranged in a semi-open structure. It is related to a lower rigidity of the tested structure resulting from the lack of a stiffening wall, which is the so-called "rib". Notwithstanding the geometry of the elements, greater absolute deformation values were recorded following conventional cutting methods. The use of high-speed cutting (HSC) provided positive outcomes in terms of minimising the deformation of thin-walled elements. Additionally, it was found that higher absolute deformations were obtained for EN AW-7075 T651 alloy.

Gold Nanorods for Doxorubicin Delivery: Numerical Analysis of Electric Field Enhancement, Optical Properties and Drug Loading/Releasing Efficiency.

The optical properties and electric field enhancement of gold nanorods for different cases were investigated in this study. The numerical analysis was carried out to understand the functionality and working of gold nanorods, while the experimental portion of the work was focused on the efficiency of gold nanorods for targeted drug delivery. COMSOL Multiphysics was used for numerical analysis. The theoretical results suggest the use of gold nanorods (AuNRs) for anticancer applications. The resonance peaks for gold nanorods of 10 nm diameter were observed at 560 nm. The resonance peaks shifted towards longer wavelengths with an increase in nanorod size. The resonance peaks showed a shift of 140 nm with a change in nanorod length from 25 to 45 nm. On the experimental side, 22 nm, 35 nm and 47 nm long gold nanorods were produced using the seed-mediated growth method. The surface morphology of the nanorods, as well as their optical characteristics, were characterized. Later, gold nanorods were applied to the targeted delivery of the doxorubicin drug. Gold nanorods showed better efficiency for doxorubicin drug loading time, release time, loading temperature, and release temperature. These results reveal that AuNRs@DA possess good ability to load and deliver the drug directly to the tumorous cells since these cells show high temperature and acidity.

Post-Machining Deformations of Thin-Walled Elements Made of EN AW-2024 T351 Aluminum Alloy as Regards the Mechanical Properties of the Applied, Rolled Semi-Finished Products.

The paper presents an evaluation of post-machining deformations of thin-walled elements as regards the mechanical properties of the applied, rolled semi-finished products. Nowadays, wrought aluminum alloys, supplied primarily in the form of rolled plates, are widely applied in the production of thin-walled integral parts. Considering the high requirements for materials, especially in the aviation sector, it is important to be aware of their mechanical properties and for semi-finished products delivered after plastic working to take into account the so-called "technological history" concerning, inter alia, the direction of rolling. The study focused on determining the influence of the ratio of the tension direction to the rolling direction on the selected mechanical properties of the EN AW-2024 T351 aluminum alloy depending on the sample thickness and its relation to the deformation of thin-walled parts. Based on the obtained results, it was found that the sample thickness and the ratio of the tension direction to the rolling direction affected the mechanical properties of the selected aluminum alloy, which in turn translated into post-machining deformations. Summarizing, the textured surface layer had a significant impact on the mentioned deformation. Greater deformations were noted for samples made of a semi-finished product with a thickness of 5 mm in comparison to 12 mm. It was the result of the influence of the surface layer, which at lower thickness had a higher percentage of contents than in thicker samples.

A Comparison of the Geometrical Accuracy of Thin-Walled Elements Made of Different Aluminum Alloys.

In modern constructions, especially aircraft, the aim is to minimize the weight of the components used. This necessitates the use of innovative construction materials, or the production of these parts with ever-decreasing wall thicknesses. To simplify assembly and improve strength properties, so-called structural elements are being used in the form of monolithic elements, which are replacing the assemblies of parts joined by, for example, riveting. These structures often have a complex, thin-walled geometry with deep pockets. This paper attempts to assess the accuracy of manufacturing thin-walled elements, in the shape of walls with different geometries, made of various aluminum alloys. Machining tests were conducted at different cutting speeds, which allowed comparisons of the geometric accuracy of parts manufactured under conventional and high-speed cutting conditions. Based on the result obtained, it was found that the elements made of EN AW-7075 T651 alloy underwent the greatest deformations during machining in comparison to other two materials (EN AW-6082 T651 and EN AC-43000). An increase in the geometrical accuracy of the manufactured elements was also observed with the increase in the cutting speed for the HSC range. Hence, to minimize the postmachining deformation of thin-walled elements, the use of high-speed cutting is justified.

Pre-Machining of Rolled Plates as an Element of Minimising the Post-Machining Deformations.

The paper presents the influence of the milling strategy, the relation between the cutting tool feed direction and the rolling direction, as well as the pre-machining consisting of the removal of the textured surface layer of rolled plates in the rolling process on the thin-walled elements deformations made of the EN AW-2024 T351 wrought aluminium alloy, after milling. The research used strategies such as: high-performance cutting (HPC), high-speed cutting (HSC) and conventional milling (CM), as well as their combinations. Another tested variable was the relation between the tool feed direction and the rolling direction. In addition, the tests were carried out in the following versions: leaving the textured surface layer created after plastic working and with its removal with technological parameters corresponding to HSC and CM. Based on the obtained results, it was found that the post-machining deformation of thin-walled elements can be minimised owing to the use of a selected milling strategy and its combination with pre-machining (or lack thereof). It was also observed that larger deformations were obtained for samples after milling in the direction perpendicular to the rolling direction.

Techniques for Thin-Walled Element Milling with Respect to Minimising Post-Machining Deformations.

The paper examines the impact of selected machining techniques and the semi-finished product technological history on deformations of thin-walled elements made of EN AW-2024 T351 aluminium alloy after milling. The following techniques have been implemented: High Performance Cutting, High Speed Cutting, conventional finishing (CF) and combinations of these techniques. As for the semi-finished product technological history, the rolling direction has been analysed. It has been assumed that it can be relevant in relation to the cutting tool feed direction and, in consequence, exert considerable impact on the stress, as well as deformation following machining. The interest in this issue proceeds from significant challenges faced by the industry, particularly in the aerospace sector. The analysis of results obtained has shown that milling in the direction perpendicular to the rolling direction results in larger deformations than milling in the parallel direction. Additionally, it has been revealed that applying a correctly selected machining technique makes it possible to minimise post-machining deformations of thin-walled elements.

Cutting Force during Surface Layer Milling of Selected Aluminium Alloys.

This paper presents the analysis of cutting force during surface layer milling of selected aluminium alloys, which are widely used in the aviation industry. The cutting force is one of the most important parameters determining the machinability of the material and also provides important information about the course of the cutting. The study analysed the influence of the technological parameters, i.e., cutting speed vc and depth of cut ap as well as the relation between cutting tool feed direction and rolling direction on the value of cutting force during milling of selected aluminium alloys, i.e., EN AW-2017A T451 and EN AW-2024 T351. The material anisotropy is a very important issue, since the engineering industry faces enormous problems related to the cutting of the tested materials that are usually supplied in the form of rolled plates. The surface layer was cut due to the fact that it accumulates the greatest residual stresses. The measurement process of cutting force was performed by using 9257B Kistler piezoelectric dynamometer. As part of the analysis of the results, the measurement uncertainty was also estimated, which was determined on the basis of two components obtained by using the A and B methods, respectively.

Helicobacter pylori--a risk factor for the developement of the central serous chorioretinopathy.

PURPOSE: To prove the influence oftte Helicobcter pylor for the development of the central serous chororetinopathy. MATERIAL AND METHODS: We examined 55 patients with central serous chorioretinopathy confirmed by fluorescein angiogram and 55 controls. Each patient provided venous blood sample for IgG antibodies to Helicobacter pylori by enzyme-linked immunosorbent assay technique (ELISA) and a stool specimen for Helicobacter pylori antigens. RESULTS: 44% in CSC patients were positive results of stool examine and only 29% in group comtrol. In 67% of the patients we proved the presence of the antibodies IgG--anty Helicobacter pylori and in 47% controls. The difference was statistically significant. CONCLUSIONS: Helicobacter pylori infection is statistically more frequently among the patients with CSC diagnosis than in healthy population.

Tribological Aspects of Cutting Tool Wear during the Turning of Stainless Steels.

The research paper presents the tribological aspects of cutting tool wear during the turning of stainless steels. An experiment was conducted in order to assess the wear of carbide cutting inserts with CVD-applied anti-wear coatings (CNMG 12 04 08 ZSZ and CNMA 12 04 12-KR 3205) and an uncoated ceramic cutting insert (CNGA 12 04 08 T0102 WG 650). The test subject included the following stainless steel grades X20Cr13 (1.4021) and X8CrNiS18-9 (1.4305). The analysis involved the direct wear indicator, VBBmax, and the indirect wear indicator, which was the roughness of machined surfaces and the Ra parameter. Based on the obtained results for both X20Cr13 and X8CrNiS18-9 steels, it was noticed that the best durability was exhibited by the CNMG 12 04 08 ZSZ insert, whereas the worst durability was identified for the CNGA 12 04 08 T0102 WG 650 insert. When analysing the results obtained with the VBBmax direct indicator, it was observed that in the case of each of the insert, most often the course of their wear was of nature similar to linear. Comparing the VBBmax direct indicator with the indirect indicator, namely, the measured Ra parameter, it was concluded that they were convergent. Upon the deterioration of the surface quality, greater values of the selected geometric measure of wear on the flank face were also identified.

[Ocular manifestations during hepatitis C infection]. / Objawy oczne u chorych zakazonych wirusem C zapalenia watroby (HCV).

Hepatitis C wirus is one of the major blood-born pathogens of huge epidemic value. Due to its easy transmission, lack of routinely pursued tests and long non-symptomatic period makes it crucial to be alert for all co-morbidites suggesting HCV infection. Consequently to reduce its farther transmission large knowledge of HCV should be spread as there is still no effective means of prophylaxis and its therapy is much costly. This article describes ophthalmic symptoms of hepatitis C virus infection such a mere keratoconiunctivitis sicca to ischemic retinopathy, macular edema and ischemic neuropathy.

[The role of Helicobacter pylori in etiopathogenesis of central serous choroidopathy]. / Rola zakazenia Helicobacter pylori w patogenezie centralnej surowiczej choroidopatii.

Central serous chorioretinopathy (CRS) is a serous macular detachment that usually affects young people and leads fortunately to a spontaneous resolution and a good visual prognosis in most patients. The etiopathogenesis of the disease is still not completely understood and no effective treatment is available at this time. However, an association has been recently highlighted between Helicobacter pylori infection and CRS connected with pathology of retinal vessels.