On-demand tuned hazard free elastomeric composites: A green approach.

Rising ecological concerns and depletion of the potentially harmful environmental impacts caused by rubber products, are of prime importance in the industry. Therefore, implementation of sustainable greener materials is required to minimize the detrimental influences. In this research, we investigated the beneficial influence of naturally derived bio-resin toward the effects of association with Zinc Oxide Nanoparticles in highly dispersible silica (HDS) reinforced Natural rubber (NR)/Epoxidized Natural Rubber (ENR)-based composites. This novel green composite offers impressive properties which were analyzed based on bound rubber content, transmission electron microscopy, physico-mechanical, dynamic mechanical, and cure characteristics. Nanoindentation studies demonstrated the enhanced hysteresis phenomenon of the green composites. The small angle X-ray scattering (SAXS) characterization has been studied by using a Beaucage model and results corroborates that the insertion of bio-resin exhibits ameliorated state of silica dispersion in the green composites. Overall, the study with the bio-resin has provided the impetus in employing it as an alternative to the expensive synthetic route of silane coupling agent and toxic process oil.

Cross-Talk Signal Free Recyclable Thermoplastic Polyurethane/Graphene-Based Strain and Pressure Sensor for Monitoring Human Motions.

Developing a sensor that can read out cross-talk free signals while determining various active physiological parameters is demanding in the field of point-of-care applications. While there are a few examples of non-flexible sensors available, the management of electronic waste generated from such sensors is critical. Most of such available sensors are rigid in form factor and hence limit their usability in healthcare monitoring due to their poor conformity to human skin. Combining these facets, studies on the development of a recyclable cross-talk free flexible sensor for monitoring human motions and active parameters are far and few. In this work, we report on the development of a recyclable flexible sensor that can provide accurate data for detecting small changes in strain as well as pressure. The developed sensor could decipher the signals individually responsible due to strain as well as pressure. Hence, it can deliver a cross-talk free output. Thermoplastic polyurethane and graphene were selected as the model system. The thermoplastic polyurethane/graphene sensor exhibited a tensile strain sensitivity of GF ≃ 3.375 for 0-100% strain and 10.551 for 100-150% strain and a pressure sensitivity of ∼-0.25 kPa-1. We demonstrate the applicability of the strain sensor for monitoring a variety of human motions ranging from a very small strain of eye blinking to a large strain of elbow bending with unambiguous peaks and a very fast response and recovery time of 165 ms. The signals received are mostly electrical hysteresis free. To confirm the recyclability, the developed sensor was recycled up to three times. Marginal decrement in the sensitivity was noted with recycling without compromising the sensing capabilities. These findings promise to open up a new avenue for developing flexible sensors with lesser carbon footprints.

Influence of Ultraviolet Radiation on Mechanical Properties of a Photoinitiator Compounded High Vinyl Styrene-Butadiene-Styrene Block Copolymer.

Ultraviolet curing of elastomers is a special curing technique that has gained importance over the conventional chemical crosslinking method, because the former process is faster, and thus, time-saving. Usually, a suitable photoinitiator is required to initiate the process. Ultraviolet radiation of required frequency and intensity excites the photoinitiator which abstracts labile hydrogen atoms from the polymer with the generation of free radicals. These radicals result in crosslinking of elastomers via radical-radical coupling. In the process, some photodegradation may also take place. In the present work, a high vinyl (~50%) styrene-butadiene-styrene (SBS) block copolymer which is a thermoplastic elastomer was used as the base polymer. An attempt was made to see the effect of ultraviolet radiation on the mechanical properties of the block copolymer. The process variables were time of exposure and photoinitiator concentration. Mechanical properties like tensile strength, elongation at break, modulus at different elongations and hardness of the irradiated samples were studied and compared with those of unirradiated ones. In this S-B-S block copolymer, a relatively low exposure time and low photoinitiator concentration were effective in obtaining optimized mechanical properties. Infrared spectroscopy, contact angle and scanning electron microscopy were used to characterize the results obtained from mechanical measurements.

Facile Synthesis and Characterization of Few-Layer Multifunctional Graphene from Sustainable Precursors by Controlled Pyrolysis, Understanding of the Graphitization Pathway, and Its Potential Application in Polymer Nanocomposites.

The key feature of the present work is the dexterous utilization of an apparently destructive process, pyrolysis, for the synthesis of the most esteemed nanomaterial, graphene. This work is an attempt to synthesize graphene from nonconventional sources such as tannic acid, alginic acid, and green tea by a controlled pyrolysis technique. The precursors used in this work are not petroleum-derived and hence are green. A set of pyrolysis experiments was carried out at different temperatures, followed by a thorough step-by-step analysis of the product morphology, enabling the optimization of the graphitization conditions. A time-dependent morphological analysis was also carried out along with isothermal thermogravimetric studies to optimize the ideal pyrolysis time for graphitization. The specific capacitance of the graphene obtained from alginic acid was 315 F/g, which makes it fairly suitable for application as green supercapacitors. The same graphene was also used to fabricate a rubber-latex-based flexible supercapacitor film with 137 F/g specific capacitance. The graphene and graphene-based latex film exhibited room-temperature magnetic hysteresis, indicating their ferromagnetic nature, which also supports their spintronic applications.

Self-healable hydrophobic polymer material having urethane linkages via a non-isocyanate route and dynamic Diels-Alder 'click' reaction.

Conventional synthesis of polyurethane (PU) often involves the use of inherently toxic and overly moisture-sensitive isocyanates. Herein, we report the preparation of a self-healable hydrophobic polymer network having urethane linkages via a facile non-isocyanate route based on carbonylimidazole-amine reaction and dynamic Diels-Alder (DA) 'click' reaction based on furan-maleimide cycloaddition. This isocyanate-free DA 'clicked' polymer material showed excellent self-healing and hydrophobic characteristics.

Effect of Prestrain on the Actuation Characteristics of Dielectric Elastomers.

Dielectric elastomers (DEs) represent a class of electroactive polymers that deform due to electrostatic attraction between oppositely charged electrodes under a varying electric field. Over the last couple of decades, DEs have garnered considerable attention due to their much-coveted actuation properties. As far as the precise measurement systems are concerned, however, there is no standard instrument or interface to quantify various related parameters, e.g., actuation stress, strain, voltage and creeping etc. In this communication, we present an in-depth study of dielectric actuation behavior of dielectric rubbers by the state-of-the-art "Dresden Smart Rubber Analyzer" (DSRA), designed and developed in-house. The instrument allowed us to elucidate various factors that could influence the output efficiency of the DEs. Herein, several non-conventional DEs such as hydrogenated nitrile rubber, nitrile rubber with different acrylonitrile contents, were employed as an electro-active matrix. The effect of viscoelastic creeping on the prestrain, molecular architecture of the matrices, e.g., nitrile content of nitrile-butadiene rubber (NBR) etc., are also discussed in detail.

Morphology-induced physico-mechanical and biological characteristics of TPU-PDMS blend scaffolds for skin tissue engineering applications.

Composition and architecture of scaffolds are the most important factors determining the performance of skin substitutes. In this work, morphology induced unique physical and biological characteristics of compatibilized TPU-PDMS blend scaffolds at 90:10, 80:20, and 70:30 blend ratios of TPU and PDMS was studied. The fiber morphology, porosity, surface wettability, and mechanical properties of electrospun scaffolds were distinctly influenced by the presence of PDMS. Interestingly, the scaffold architecture varied from electrospun fibers to porous fibers and finally occurrence of unique porous beads noticed at 30% PDMS in the microstructure which was confirmed using FESEM. Micro-CT analysis revealed that the porosity of electrospun scaffolds was enhanced from 61% to 79% with 30 parts of PDMS addition. Moreover, MTT assay and cell proliferation were studied using human skin fibroblast cells and found to be significantly enhanced with the PDMS percentage. TPU-PDMS blends offer better overall performance at 70:30 blend ratio of TPU and PDMS (T70P30). Only 4% of hemolysis was observed for T70P30 blends, which establishes the hemocompatibility of the material. In comparison, the results reveal the potential of the cytocompatible T70P30 scaffold for the fabrication of skin substitutes for tissue engineering applications. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 1634-1644, 2019.