Tumble Kinematics of Escherichia coli near a Solid Surface.

Bacteria tumble periodically, following environmental cues. Whether they can tumble near a solid surface is a basic issue for the inception of infection or mineral biofouling. Observing freely swimming Escherichia coli near and parallel to a glass surface imaged at high magnification (×100) and high temporal resolution (500 Hz), we identified tumbles as events starting (or finishing, respectively) in abrupt deceleration (or reacceleration, respectively) of the body motion. Selected events show an equiprobable clockwise (CW) or counterclockwise change in direction that is superimposed on a surface CW path because of persistent propulsion. These tumbles follow a common long (about 300 ± 100 ms, N = 52) deceleration-reorientation-acceleration pattern. A wavelet transform multiscale analysis shows these tumbles cause in-plane diffusive reorientations with 1.5 rad2/s rotational diffusivity, a value that compares with that measured in bulk tumbles. In half of the cases, additional few-millisecond bursts of an almost equiprobable CW or counterclockwise change of direction (12 ± 90°, N = 89) occur within the reorientation stage. The highly dispersed absolute values of change of direction (70 ± 66°, N = 89) of only a few bursts destabilize the cell-swimming direction. These first observations of surface tumbles set a foundation for statistical models of run-and-tumble surface motion different from that in bulk and lend support for chemotaxis near solid surface.

Improved Cycling Performance of a Si Nanoparticle Anode Utilizing Citric Acid as a Surface-Modifying Agent.

Citric acid and its analogues have been investigated as surface-modifying agents for Si nanoparticle anodes using electrochemical cycling, attenuated total reflectance infrared (ATR IR), and X-ray photoelectron spectroscopy (XPS). A Si nanoparticle anode prepared with citric acid (CA) has better capacity retention than one containing 1,2,3,4-butanetetracarboxylic acid (BA), but both electrodes outperform Si-PVDF. The Si-CA anode has an initial specific capacity of 3530 mA h/g and a first cycle efficiency of 82%. Surprisingly, the Si-CA electrode maintains a high specific capacity of ∼2200 mA h/g after 250 cycles, corresponding to 64% capacity retention, which is similar to the Si prepared with long-chain poly(acrylic acid) (PAA). On the contrary, the silicon electrode prepared with PVDF has a fast capacity fade and retains only 980 mA h/g after 50 cycles. The IR and XPS data show that the Si-CA electrode has an SEI composed primarily of lithium citrate during the first 50 cycles, resulting from the electrochemical reduction of citric acid. Only low concentrations of electrolyte reduction products are observed. The lithium citrate layer derived from CA stabilizes the silicon surface and suppresses electrolyte reduction, which likely contributes to the enhanced cycling performance of the Si nanoparticle anode.

Systematic Investigation of Binders for Silicon Anodes: Interactions of Binder with Silicon Particles and Electrolytes and Effects of Binders on Solid Electrolyte Interphase Formation.

The effects of different binders, polyvinylidene difluoride (PVdF), poly(acrylic acid) (PAA), sodium carboxymethyl cellulose (CMC), and cross-linked PAA-CMC (c-PAA-CMC), on the cycling performance and solid electrolyte interphase (SEI) formation on silicon nanoparticle electrodes have been investigated. Electrodes composed of Si-PAA, Si-CMC, and Si-PAA-CMC exhibit a specific capacity ≥3000 mAh/g after 20 cycles while Si-PVdF electrodes have a rapid capacity fade to 1000 mAh/g after just 10 cycles. Infrared spectroscopy (IR) and X-ray photoelectron spectroscopy (XPS) reveal that PAA and CMC react with the surface of the Si nanoparticles during electrode fabrication. The fresh Si-CMC electrode has a thicker surface coating of SiOx than Si-PAA and Si-PAA-CMC electrodes, due to the formation of thicker SiOx during electrode preparation, which leads to lower cyclability. The carboxylic acid functional groups of the PAA binder are reactive toward the electrolyte, causing the decomposition of LiPF6 and dissolution of SiOx during the electrode wetting process. The PAA and CMC binder surface films are then electrochemically reduced during the first cycle to form a protective layer on Si. This layer effectively suppresses the decomposition of carbonate solvents during cycling resulting in a thin SEI. On the contrary, the Si-PVDF electrode has poor cycling performance and continuous reduction of carbonate solvents is observed resulting in the generation of a thicker SEI. Interestingly, the Lewis basic -CO2Na of CMC was found to scavenge HF in electrolyte.

Hard X-ray Photoelectron Spectroscopy (HAXPES) Investigation of the Silicon Solid Electrolyte Interphase (SEI) in Lithium-Ion Batteries.

Binder-free silicon (BF-Si) nanoparticle anodes were cycled with 1.2 M LiPF6 in ethylene carbonate (EC), fluoroethylene carbonate (FEC), or EC with 15% FEC (EC:FEC), extracted from cells and analyzed by Hard X-ray Photoelectron Spectroscopy (HAXPES). All of the electrolytes generate an SEI which is integrated with Si containing species. The EC and EC:FEC electrolytes result in the generation of LixSiOy after the first cycle while LixSiOy is only observed after five cycles for the FEC electrolyte. The SEI initially generated from the EC electrolyte is primarily composed of lithium ethylene dicarbonate (LEDC) and LiF. However, after five cycles, the composition changes, especially near the surface of silicon because of decomposition of the LEDC. The SEI generated from the EC:FEC electrolytes contains LEDC, LiF, and poly(FEC) and small changes are observed upon additional cycling. The SEI generated with the FEC electrolyte contains LiF and poly(FEC) and small changes are observed upon additional cycling. The stability of the SEI correlates with the observed capacity retention of the cells.

Facile synthesis and high anode performance of carbon fiber-interwoven amorphous nano-SiOx/graphene for rechargeable lithium batteries.

We present the first report on carbon fiber-interwoven amorphous nano-SiOx/graphene prepared by a simple and facile room temperature synthesis of amorphous SiOx nanoparticles using silica, followed by their homogeneous dispersion with graphene nanosheets and carbon fibers in room temperature aqueous solution. Transmission and scanning electron microscopic imaging reveal that amorphous SiOx primary nanoparticles are 20-30 nm in diameter and carbon fibers are interwoven throughout the secondary particles of 200-300 nm, connecting SiOx nanoparticles and graphene nanosheets. Carbon fiber-interwoven nano-SiO0.37/graphene electrode exhibits impressive cycling performance and rate-capability up to 5C when evaluated as a rechargeable lithium battery anode, delivering discharge capacities of 1579-1263 mAhg(-1) at the C/5 rate with capacity retention of 80% and Coulombic efficiencies of 99% over 50 cycles, and nearly sustained microstructure. The cycling performance is attributed to synergetic effects of amorphous nano-SiOx, strain-tolerant robust microstructure with maintained particle connectivity and enhanced electrical conductivity.