Influence of stearic acid coating of the NaCl surface on the reactivity with NO2 under humidity.

In the atmosphere, sea salt aerosols, containing mainly NaCl, can accumulate fatty acids and undergo heterogeneous chemistry with atmospheric nitrogen oxides. The effect of stearic acid (SA) coating on the reactivity of the NaCl(100) surface with NO2 under humidity was studied by atomic force microscopy (AFM), Raman mapping and time-of-flight secondary ion mass spectrometry (ToF-SIMS) to highlight processes occurring on NaCl surfaces. The vapor-deposition of SA on the NaCl surface generates heterogeneous coating with discontinuous monolayer islands. The SA molecules with all-trans conformation stick to the NaCl surface through -CO2H groups and are organized in parallel between them and nearly perpendicularly to the surface. The SA coating does not prevent the NaNO3 particle formation when the sample is exposed to NO2 under low humidity conditions. The initial abilities of the NaCl surface coated with SA to pick up NO2 from the gas phase are correlated with the fraction of bare NaCl area evidencing the spatially heterogeneous reactivity of the surface. The role of H2O in the NO2 uptake and the catalytic conversion of NaCl to NaNO3 is shown. Under humidity (RH = 50%), the H2O uptake by NaNO3 particles on the coated-NaCl surface is significantly more important than that adsorbed under analogous conditions without the presence of NaNO3 particles. This unusual water absorption initiates transitions (i) from solid NaNO3 particles to NaNO3 aqueous solution and (ii) from the SA monolayer with well-ordered all trans alkyl chains to the SA gel with completely disordered conformation. This mixed SA/NaNO3 layer on the particle surface may have significant consequences on the hygroscopic properties and reactivity of the sea salt aerosols in the atmosphere.

Oxide diffusion in innovative SOFC cathode materials.

Oxide diffusion was studied in two innovative SOFC cathode materials, Ba(2)Co(9)O(14) and Ca(3)Co(4)O(9)+δ derivatives. Although oxygen diffusion was confirmed in the promising material Ba(2)Co(9)O(14), it was not possible to derive accurate transport parameters because of an oxidation process at the sample surface which has still to be clarified. In contrast, oxygen diffusion in the well-known Ca(3)Co(4)O(9)+δ thermoelectric material was improved when calcium was partly substituted with strontium, likely due to an increase of the volume of the rock salt layers in which the conduction process takes place. Although the diffusion coefficient remains low, interestingly, fast kinetics towards the oxygen molecule dissociation reaction were shown with surface exchange coefficients higher than those reported for the best cathode materials in the field. They increased with the strontium content; the Sr atoms potentially play a key role in the mechanism of oxygen molecule dissociation at the solid surface.

Toward the understanding of the interfacial dairy fouling deposition and growth mechanisms at a stainless steel surface: a multiscale approach.

The microstructures of two dairy fouling deposits obtained at a stainless steel surface after different processing times in a pilot plate heat exchanger were investigated at different scales. Electron-Probe Micro Analysis, Time-of-Flight Secondary Ion Mass Spectrometry, Atomic Force Microscopy, and X-Ray Photo-electron Spectroscopy techniques were used for this purpose. The two model fouling solutions were made by rehydrating whey protein in water containing calcium or not. Results on samples collected after 2h processing show that the microstructure of the fouling layers is completely different depending on calcium content: the layer is thin, smooth, and homogeneous in absence of calcium and on the contrary very thick and rough in presence of calcium. Analyses on substrates submitted to 1 min fouling reveal that fouling mechanisms are initiated by the deposit of unfolded proteins on the substrate and start immediately till the first seconds of exposure with no lag time. In presence of calcium, amorphous calcium carbonate nuclei are detected in addition to unfolded proteins at the interface, and it is shown that the protein precedes the deposit of calcium on the substrate. Moreover, it is evidenced that amorphous calcium carbonate particles are stabilized by the unfolded protein. They are thus more easily trapped in the steel roughnesses and contribute to accelerate the deposit buildup, offering due to their larger characteristic dimension more roughness and favorable conditions for the subsequent unfolded protein to depose.