Monitoring of Cardiorespiratory Parameters during Sleep Using a Special Holder for the Accelerometer Sensor.

Sleep is extremely important for physical and mental health. Although polysomnography is an established approach in sleep analysis, it is quite intrusive and expensive. Consequently, developing a non-invasive and non-intrusive home sleep monitoring system with minimal influence on patients, that can reliably and accurately measure cardiorespiratory parameters, is of great interest. The aim of this study is to validate a non-invasive and unobtrusive cardiorespiratory parameter monitoring system based on an accelerometer sensor. This system includes a special holder to install the system under the bed mattress. The additional aim is to determine the optimum relative system position (in relation to the subject) at which the most accurate and precise values of measured parameters could be achieved. The data were collected from 23 subjects (13 males and 10 females). The obtained ballistocardiogram signal was sequentially processed using a sixth-order Butterworth bandpass filter and a moving average filter. As a result, an average error (compared to reference values) of 2.24 beats per minute for heart rate and 1.52 breaths per minute for respiratory rate was achieved, regardless of the subject's sleep position. For males and females, the errors were 2.28 bpm and 2.19 bpm for heart rate and 1.41 rpm and 1.30 rpm for respiratory rate. We determined that placing the sensor and system at chest level is the preferred configuration for cardiorespiratory measurement. Further studies of the system's performance in larger groups of subjects are required, despite the promising results of the current tests in healthy subjects.

A Smart Sensor-Based Measurement System for Advanced Bee Hive Monitoring.

The widespread decline of honey bee (Apis mellifera L.) colonies registered in recent years has raised great attention to the need of gathering deeper knowledge about this phenomenon, by observing the colonies' activity to identify possible causes, and design corresponding countermeasures. In fact, honey bees have well-known positive effects on both the environment and human life, and their preservation becomes critical not only for ecological reasons, but also for the social and economic development of rural communities. Smart sensor systems are being developed for real-time and long-term measurement of relevant parameters related to beehive conditions, such as the hive weight, sounds emitted by the bees, temperature, humidity, and CO 2 inside the beehive, as well as weather conditions outside. This paper presents a multisensor platform designed to measure the aforementioned parameters from beehives deployed in the field, and shows how the fusion of different sensor measurements may provide insights on the status of the colony, its interaction with the surrounding environment, and the influence of climatic conditions.

Human activity monitoring system based on wearable sEMG and accelerometer wireless sensor nodes.

BACKGROUND: The human activity monitoring technology is one of the most important technologies for ambient assisted living, surveillance-based security, sport and fitness activities, healthcare of elderly people. The activity monitoring is performed in two steps: the acquisition of body signals and the classification of activities being performed. This paper presents a low-cost wearable wireless system specifically designed to acquire surface electromyography (sEMG) and accelerometer signals for monitoring the human activity when performing sport and fitness activities, as well as in healthcare applications. RESULTS: The proposed system consists of several ultralight wireless sensing nodes that are able to acquire, process and efficiently transmit the motion-related (biological and accelerometer) body signals to one or more base stations through a 2.4 GHz radio link using an ad-hoc communication protocol designed on top of the IEEE 802.15.4 physical layer. A user interface software for viewing, recording, and analysing the data was implemented on a control personal computer that is connected through a USB link to the base stations. To demonstrate the capability of the system of detecting the user's activity, data recorded from a few subjects were used to train and test an automatic classifier for recognizing the type of exercise being performed. The system was tested on four different exercises performed by three people, the automatic classifier achieved an overall accuracy of 85.7% combining the features extracted from acceleration and sEMG signals. CONCLUSIONS: A low cost wireless system for the acquisition of sEMG and accelerometer signals has been presented for healthcare and fitness applications. The system consists of wearable sensing nodes that wirelessly transmit the biological and accelerometer signals to one or more base stations. The signals so acquired will be combined and processed in order to detect, monitor and recognize human activities.

Heart rate detection with accelerometric sensors under the mattress.

The ballistocardiography is a technique that measures the heart rate from the mechanical vibrations of the body due to the heart movement. In this work a novel noninvasive device placed under the mattress of a bed estimates the heart rate using the ballistocardiography. Different algorithms for heart rate estimation have been developed.

Embedded system for non-obtrusive sleep apnea detection.

This document presents a new complete standalone system for a recognition of sleep apnea using signals from the pressure sensors placed under the mattress. The developed hardware part of the system is tuned to filter and to amplify the signal. Its software part performs more accurate signal filtering and identification of apnea events. The overall achieved accuracy of the recognition of apnea occurrence is 91%, with the average measured recognition delay of about 15 seconds, which confirms the suitability of the proposed method for future employment. The main aim of the presented approach is the support of the healthcare system with the cost-efficient tool for recognition of sleep apnea in the home environment.

Homomorphic Deconvolution for MUAP Estimation From Surface EMG Signals.

This paper presents a technique for parametric model estimation of the motor unit action potential (MUAP) from the surface electromyography (sEMG) signal by using homomorphic deconvolution. The cepstrum-based deconvolution removes the effect of the stochastic impulse train, which originates the sEMG signal, from the power spectrum of sEMG signal itself. In this way, only information on MUAP shape and amplitude were maintained, and then, used to estimate the parameters of a time-domain model of the MUAP itself. In order to validate the effectiveness of this technique, sEMG signals recorded during several biceps curl exercises have been used for MUAP amplitude and time scale estimation. The parameters so extracted as functions of time were used to evaluate muscle fatigue showing a good agreement with previously published results.

An Investigation on the Accuracy of Truncated DKLT Representation for Speaker Identification With Short Sequences of Speech Frames.

Speaker identification plays a crucial role in biometric person identification as systems based on human speech are increasingly used for the recognition of people. Mel frequency cepstral coefficients (MFCCs) have been widely adopted for decades in speech processing to capture the speech-specific characteristics with a reduced dimensionality. However, although their ability to decorrelate the vocal source and the vocal tract filter make them suitable for speech recognition, they greatly mitigate the speaker variability, a specific characteristic that distinguishes different speakers. This paper presents a theoretical framework and an experimental evaluation showing that reducing the dimension of features by applying the discrete Karhunen-Loève transform (DKLT) to the log-spectrum of the speech signal guarantees better performance compared to conventional MFCC features. In particular with short sequences of speech frames, with typical duration of less than 2 s, the performance of truncated DKLT representation achieved for the identification of five speakers are always better than those achieved with the MFCCs for the experiments we performed. Additionally, the framework was tested on up to 100 TIMIT speakers with sequences of less than 3.5 s showing very good recognition capabilities.

Analysis of the EMG Signal During Cyclic Movements Using Multicomponent AM-FM Decomposition.

Sport, fitness, as well as rehabilitation activities, often require the accomplishment of repetitive movements. The correctness of the exercises is often related to the capability of maintaining the required cadence and muscular force. Failure to maintain the required force, also known as muscle fatigue, is accompanied by a shift in the spectral content of the surface electromyography (EMG) signal toward lower frequencies. This paper presents a novel approach for simultaneously obtaining exercise repetition frequency and evaluating muscular fatigue, as functions of time, by only using the EMG signal. The mean frequency of the amplitude spectrum (MFA) of the EMG signal, considered as a function of time, is directly related to the dynamics of the movement performed and to the fatigue of the involved muscles. If the movement is cyclic, MFA will display the same pattern and its average will tend to decrease. These two effects have been simultaneously modeled by a two-component AM-FM model based on the Hilbert transform. The method was tested on signals recorded using a wireless system applied to healthy subjects performing dumbbell biceps curls, dumbbell lateral rises, and bodyweight squats. Experimental results show the excellent performance of the proposed technique.