Differential Precipitation of Mg(OH)2 from CaSO4·2H2O Using Citrate as Inhibitor-A Promising Concept for Reagent Recovery from MgSO4 Waste Streams.

In hydrometallurgical processing and acidic wastewater treatment, one of the neutralizing agents employed is MgO or Mg(OH)2. At the end of this process, the resulting solution, which is rich in SO42- and Mg2+ is treated with lime to remove (or minimize the amount) of these ions via the precipitation of Mg(OH)2 and CaSO4·2H2O (gypsum). In our work, an attempt was made to separate the two solids by increasing the induction time of the gypsum precipitation, thus regenerating relatively pure Mg(OH)2 which could be reused in wastewater treatments or hydrometallurgical processing circuits, and in this way, significantly enhancing the economic viability of the process. During our experiments, the reaction of an MgSO4 solution with milk of lime prepared from quicklime was studied. The effects of a range of organic additives, which can slow down the precipitation of gypsum have been assessed. The process was optimized for the most promising inhibiting agent-that is, the citrate ion. The reactions were continuously monitored in situ by conductometric measurements with parallel monitoring of solution pH and temperature. ICP-OES measurements were also carried out on samples taken from the reaction slurry. The composition of the precipitating solids at different reaction times was established by powder XRD and their morphology by SEM. Finally, experiments were carried out to locate the additive after the completion of the precipitation reaction to get information about its potential reuse.

The Structure and Thermal Properties of Solid Ternary Compounds Forming with Ca2+, Al3+ and Heptagluconate Ions.

In the present work, the structure and thermal stability of Ca-Al mixed-metal compounds, relevant in the Bayer process as intermediates, have been investigated. X-ray diffraction (XRD) measurements revealed the amorphous morphology of the compounds, which was corroborated by SEM-EDX measurements. The results of ICP-OES and UV-Vis experiments suggested the formation of three possible ternary calcium aluminum heptagluconate (Ca-Al-Hpgl) compounds, with the formulae of CaAlHpgl(OH)40, Ca2AlHpgl2(OH)50 and Ca3Al2Hpgl3(OH)90. Additional IR and Raman experiments revealed the centrally symmetric arrangement of heptagluconate around the metal ion. The increased thermal stability was demonstrated by thermal analysis of the solids and confirmed our findings.

Magnesium(II) d-Gluconate Complexes Relevant to Radioactive Waste Disposals: Metal-Ion-Induced Ligand Deprotonation or Ligand-Promoted Metal-Ion Hydrolysis?

The complexation equilibria between Mg2+ and d-gluconate (Gluc-) ions are of particular importance in modeling the chemical speciation in low- and intermediate-level radioactive waste repositories. NMR measurements and potentiometric titrations conducted at 25 °C and 4 M ionic strength revealed the formation of the MgGluc+, MgGlucOH0, MgGluc(OH)2-, and Mg3Gluc2(OH)40 complexes. The trinuclear species provides indirect evidence for the existence of multinuclear magnesium(II) hydroxido complexes, whose formation was proposed earlier but has not been confirmed yet. Additionally, speciation calculations demonstrated that MgCl2 can markedly decrease the solubility of thorium(IV) at low ligand concentrations. Regarding the structure of MgGluc+, both IR spectra and density functional theory (DFT) calculations indicate the monodentate coordination of Gluc-. By the potentiometric data, the acidity of the water molecules is higher in the MgGluc+ and MgGlucOH0 species than in the Mg(H2O)62+ aqua ion. On the basis of DFT calculations, this ligand-promoted hydrolysis is caused by strong hydrogen bonds forming between Gluc- and Mg(H2O)62+. Conversely, metal-ion-induced ligand deprotonation takes place in the case of calcium(II) complexes, giving rise to salient variations on the NMR spectra in a strongly alkaline medium.

Ball Milling of Copper Powder Under Dry and Surfactant-Assisted Conditions-On the Way Towards Cu/Cu2O Nanocatalyst.

Samples of copper powder was milled with varied grinding frequencies in the presence of various organic agents (oleylamine, ethylene glycol or dimethyl sulfoxide) or without additives. The effects of experimental conditions were investigated by X-ray diffractometry, scanning electron microscopy and dynamic light scattering measurements. The aggregation of particles were supressed by added organics. The catalytic activities of the variously treated samples were measured in the Ullmanntype reaction of iodobenzene and 1H-pyrazole.

The Synthesis and Use of Nano Nickel Catalysts.

The hydrazine reduction method was applied for the synthesis of nickel nanoparticles without using inert atmosphere and added surface active agents. The effect of the preparation temperature and the chemical quality of the metal sources as well as the solvents were studied. The generation of nanoparticles were studied primarily by X-ray diffractometry, but scanning and transmission electron microscopies as well as dynamic light scattering measurements were also used for the better understanding of the nanoparticles behaviour. The elevation of temperature was the key point in transforming Ni(OH)2 into metallic nickel. By selecting the metal source, the obtained crystallite sizes could be tailored between 7 nm and 15 nm; however, the SEM and DLS measurements revealed significant agglomeration resulting in aggregates with spherical or Ni(OH)2 resembling morphologies depending on the solvent used. The catalytic activities of the nanoparticles prepared were tested and compared in a Suzuki-Miyaura cross-coupling reaction.

Spherical LDH-Ag°-montmorillonite heterocoagulated system with a pH-dependent sol-gel structure for controlled accessibility of AgNPs immobilized on the clay lamellae.

Aqueous suspensions of spherical ZnMgAl-layered double hydroxides [LDH(sph)] and antibacterial silver nanoparticles (AgNPs) deposited on the lamellae of montmorillonite were used for the synthesis of composites, which behave like coherent gels at low pH (≲4.5) and incoherent sols at higher pH (≳4.5). The composition of the composite was chosen as LDH(sph)/Ag°-montm. = 25:75 wt % in order to ensure a sol-gel transition that can also be characterized by viscometry. This pH-sensitive heterocoagulated system consisting of oppositely charged colloid particles was suitable for the release of antimicrobial AgNPs immobilized on the clay lamellae via a pH-controlled gel-sol transition. The heterocoagulation process was also characterized by surface charge titration measurements. Spherical LDH/Ag°-montmorillonite composite samples were identified by X-ray diffraction (XRD) measurements. The morphological properties of the composites were studied, and the presence of the heterocoagulated structure was confirmed by scanning electron microscopy (SEM). The nanoscale structure of the LDH(sph)-Ag°-montmorillonite composite obtained was also verified by small-angle X-ray scattering (SAXS), and the rheological characteristics were studied at various pH values. The viscosity and yield value of the composite decreased by an order of magnitude upon increasing the pH from 3.0 to 5.5. The sol-gel transition of the composite suspension was reversible in the previously mentioned pH range.

Diterpene Constituents of Euphorbia exigua L. and Multidrug Resistance Reversing Activity of the Isolated Diterpenes.

Phytochemical investigation of the MeOH extract obtained from the aerial parts of the annual weed Euphorbia exigua L. resulted in the isolation of two novel (1, 2) and one known (3) jatrophane diterpenes. Their structures were established by extensive 1D- and 2D-NMR spectroscopy and HR-ESI-MS. The isolated compounds were evaluated for multidrug resistance (MDR) reversing activity on human MDR gene-transfected L5178 mouse lymphoma cells; and all three compounds were found to modulate the intracellular drug accumulation.

Multinuclear complex formation between Ca(II) and gluconate ions in hyperalkaline solutions.

Alkaline solutions containing polyhydroxy carboxylates and Ca(II) are typical in cementitious radioactive waste repositories. Gluconate (Gluc(-)) is a structural and functional representative of these sugar carboxylates. In the current study, the structure and equilibria of complexes forming in such strongly alkaline solutions containing Ca(2+) and gluconate have been studied. It was found that Gluc(-) significantly increases the solubility of portlandite (Ca(OH)2(s)) under these conditions and Ca(2+) complexes of unexpectedly high stability are formed. The mononuclear (CaGluc(+) and [CaGlucOH](0)) complexes were found to be minor species, and predominant multinuclear complexes were identified. The formation of the neutral [Ca2Gluc(OH)3](0) (log ß213 = 8.03) and [Ca3Gluc2(OH)4](0) (log ß324 = 12.39) has been proven via H2/Pt-electrode potentiometric measurements and was confirmed via XAS, (1)H NMR, ESI-MS, conductometry, and freezing-point depression experiments. The binding sites of Gluc(-) were identified from multinuclear NMR measurements. Besides the carboxylate group, the O atoms on the second and third carbon atoms were proved to be the most probable sites for Ca(2+) binding. The suggested structure of the trinuclear complex was deduced from ab initio calculations. These observations are of relevance in the thermodynamic modeling of radioactive waste repositories, where the predominance of the binuclear Ca(2+) complex, which is a precursor of various high-stability ternary complexes with actinides, is demonstrated.

Water types and their relaxation behavior in partially rehydrated CaFe-mixed binary oxide obtained from CaFe-layered double hydroxide in the 155-298 K temperature range.

Heat-treated CaFe-layered double hydroxide samples were equilibrated under conditions of various relative humidities (11%, 43% and 75%). Measurements by FT-IR and dielectric relaxation spectroscopies revealed that partial to full reconstruction of the layered structure took place. Water types taking part in the reconstruction process were identified via dielectric relaxation measurements either at 298 K or on the flash-cooled (to 155 K) samples. The dynamics of water molecules at the various positions was also studied by this method, allowing the flash-cooled samples to warm up to 298 K.

Catalytic antioxidant nanocomposites based on sequential adsorption of redox active metal complexes and polyelectrolytes on nanoclay particles.

An antioxidant nanocomposite was prepared by successive adsorption of redox active metal complexes (copper(ii)-bipyridyl and iron(iii)-citrate) and polyelectrolytes (poly(styrene sulfonate) and poly(diallyldimethyl ammonium)) on layered double hydroxide nanoclay. The experimental conditions were optimized in each preparation step and thus, the final composite formed highly stable colloids, i.e., excellent resistance against salt-induced aggregation was achieved. Due to the synergistic effect of the metal complexes, the developed composite showed remarkable activity in the dismutation of superoxide radicals, close to the one determined for the native superoxide dismutase enzyme. The obtained composite is highly selective for superoxide radical dismutation, while its activity in other antioxidant tests was close to negligible. Structural characterization of the composite revealed that the excellent superoxide radical scavenging ability originated from the advantageous coordination geometry around the copper(ii) center formed upon immobilization. The structure formed around the metal centers led to optimal redox features and consequently, to an improved superoxide dismutase-like activity. The catalytic antioxidant composite is a promising candidate to reduce oxidative stress in industrial manufacturing processes, where natural enzymes quickly lose their activity due to the harsh environmental conditions.

A colloid chemistry route for the preparation of hierarchically ordered mesoporous layered double hydroxides using surfactants as sacrificial templates.

An efficient synthetic route was developed to prepare hierarchically ordered mesoporous layered double hydroxide (LDH) materials. Sodium dodecyl sulfate (SDS) was used as a sacrificial template to tune the interfacial properties of the LDH materials during the synthetic process. The SDS dose was optimized to obtain stable dispersions of the SDS-LDH composites, which were calcined, then rehydrated to prepare the desired LDH structures. Results of various characterization studies revealed a clear relationship between the colloidal stability of the SDS-LDH precursors and the structural features of the final materials, which was entirely SDS-free. A comparison to the reference LDH prepared by the traditional co-precipitation-calcination-rehydration method in the absence of SDS shed light on a remarkable increase in the specific surface area (one of the highest within the previously reported LDH materials) and pore volume as well as on the formation of a beneficial pore size distribution. As a proof of concept, the mesoporous LDH was applied as adsorbent for removal of nitrate and dichromate anions from aqueous samples, and excellent efficiency was observed in both sorption capacity and recyclability. These results make the obtained LDH a promising candidate as adsorbent in various industrial and environmental processes, wherever the use of mesoporous and organic content-free materials is required.

Oxidation of Cysteinate Anions Immobilized in the Interlamellar Space of CaAl-Layered Double Hydroxide.

L-Cysteinate-intercalated CaAl-layered double hydroxide (LDH) was prepared by the co-precipitation method producing highly crystalline hydrocalumite phase with a well-pillared interlayer gallery. The obtained materials were characterized by X-ray diffractometry, IR as well as Raman spectroscopies. By performing interlamellar oxidation reactions with peracetic acid as oxidant, oxidation of cysteinate to cystinate in aqueous and cysteinate sulfenic acid in acetonic suspensions occurred. The oxidations could be performed under mild conditions, at room temperature, under neutral pH and in air. It has been shown that the transformation pathways are due to the presence of the layered structure, that is, the confined space of the LDH behaved as molecular reactor.

Copper-Loaded Layered Bismuth Subcarbonate-Efficient Multifunctional Heterogeneous Catalyst for Concerted C-S/C-N Heterocyclization.

An efficient self-supported Cu(II)Bi(III) bimetallic catalyst with a layered structure was designed and developed. By careful characterization of the as-prepared material, the host structure was identified to exhibit a Sillen-type bismutite framework, with copper(II) ions being loaded as guests. The heterogeneous catalyst enabled C-N and C-S arylations under mild reaction conditions and with high chemoselectivities, thus furnishing valuable phenothiazines via heterocyclization with wide substrate tolerance. As corroborated by detailed catalytic studies, the cooperative, bifunctional catalyst, bearing Lewis acid sites along with copper(II) catalytic sites, facilitated an intriguing concerted C-N/C-S heterocyclization mechanism. The heterogeneous nature of the catalytic reactions was verified experimentally. Importantly, the catalyst was successfully recycled and reused multiple times, persevering its original structural order as well as its initial activity.

Synthesis and spectroscopic and computational characterization of Zn4O(alicyclic or aromatic carboxylate)6 complexes as potential MOF precursors.

Potential metal-organic-framework precursors, Zn(4)O complexes with various alicyclic or aromatic carboxylate ligands, were prepared, in many cases quantitatively, from ZnO and the relevant carboxylic acids in the presence of trace amounts of water. The complexes obtained were characterized with various classical (titration) and instrumental (IR and NMR spectroscopies) methods and molecular modeling (PM3 and PM6 semiempirical quantum chemical methods and HF/6-31G** ab initio calculations). Structural peculiarities reflected in the success or failure in the synthesis could be rationalized with the combination of IR and NMR spectroscopies and molecular modeling.

Superoxide dismutase mimicking Cu(II)-mixed amino acid complexes covalently grafted onto silica gel--an FT-IR study.

Our recent work concerning the synthesis, characterisation and testing of bioinspired electron transfer catalysts is described in this contribution. The catalysts were various Cu(II) complexes having mixed C- or N-protected amino acids (L-histidine and L-tyrosine) as ligands covalently grafted onto surface-modified silica gel. The resulting materials were structurally characterised by FT-IR spectroscopy, and their superoxide dismutase activities were tested. The covalently anchored Cu(II) complexes displayed appreciable activities in the test reaction; thus, they may be considered as promising candidates as durable electron transfer catalysts approaching the efficiency of the enzyme mimicked.

Equilibria and Dynamics of Sodium Citrate Aqueous Solutions: The Hydration of Citrate and Formation of the Na3Cit0 Ion Aggregate.

Sodium citrate (Na3Cit) has a crucial role in many biological and industrial processes. Yet, quantitative information on its hydration and the ion association between Na+ and Cit3- ions in a broad range of salt concentrations is still lacking. In this work, we study both ion association equilibria and relaxation dynamics of sodium citrate solutions by combining potentiometry, spectrophotometry, and dielectric spectroscopy. From photometric and potentiometric measurements, we detect the formation of the NaCit2- ion-pair and the neutral Na3Cit0 ion aggregate in a wide range of ionic strengths (0.5-4 M). Due to its remarkable stability, the latter becomes the prevailing species at higher salt concentrations. In the dielectric spectra, we observe the dipolar relaxation of Cit3- and NaCit2- and two solvent-related processes, associated with the collective rearrangement of the H-bond network (cooperative water mode) and the H-bond flip of water molecules (fast water mode). Unlike numerous other salt solutions, the relaxation time of the cooperative mode scales with the viscosity indicating that the strongly hydrated anion fits well into the water network. That is, the stabilizing effect of anion-solvent interactions on the H-bond network outweighs the destructive impact of the cations as the latter are only present at low concentration, due to strong ion association. In conclusion, the affinity of citrate toward Na+ binding not only governs solution equilibria but also has a strong impact on water dynamics.

Ultrasound-Assisted Hydrazine Reduction Method for the Preparation of Nickel Nanoparticles, Physicochemical Characterization and Catalytic Application in Suzuki-Miyaura Cross-Coupling Reaction.

In the experimental work leading to this contribution, the parameters of the ultrasound treatment (temperature, output power, emission periodicity) were varied to learn about the effects of the sonication on the crystallization of Ni nanoparticles during the hydrazine reduction technique. The solids were studied in detail by X-ray diffractometry, dynamic light scattering, thermogravimetry, specific surface area, pore size analysis, temperature-programmed CO2/NH3 desorption and scanning electron microscopy. It was found that the thermal behaviour, specific surface area, total pore volume and the acid-base character of the solids were mainly determined by the amount of the nickel hydroxide residues. The highest total acidity was recorded over the solid under low-power (30 W) continuous ultrasonic treatment. The catalytic behaviour of the nanoparticles was tested in a Suzuki-Miyaura cross-coupling reaction over five samples prepared in the conventional as well as the ultrasonic ways. The ultrasonically prepared catalysts usually performed better, and the highest catalytic activity was measured over the nanoparticles prepared under low-power (30 W) continuous sonication.

Effects of ultrasonic irradiation on the synthesis, crystallization, thermal and dissolution behaviour of chloride-intercalated, co-precipitated CaFe-layered double hydroxide.

The output power (30-150 W) and the periodicity (20-100%) of ultrasound emission were varied in a wide range to regulate and improve the crystallization process in the commonly used co-precipitation technique of chloride-intercalated CaFe-layered double hydroxides. The influence of ultrasound irradiation on the as-prepared materials was studied by X-ray diffractometry, dynamic light scattering, UV-Vis-NIR diffuse reflectance spectroscopy, specific surface area measurement, pore size analysis, ion-selective electrode potentiometric investigations and thermogravimetry. Additionally, structural alterations due to heat treatment at various temperatures were followed in detail by Fourier-transform infrared and X-ray absorption spectroscopies as well as scanning electron microscopy. The ultrasonic treatment was capable of controlling the sizes of primarily formed (from 19 nm to 30 nm) as well as the aggregated (secondary) particles (between 450 nm and 700 nm), and thus modifying their textural parameters and enhancing the incorporation of chloride anions into the interlamellar space. For the first time, the optical energy gap of CaFe-LDH was reported here depending on the nature of applied stirring (4.18-4.34 eV). The heat-treatment investigations revealed that the layered structure was stabile until 200 °C, even at the atomic level.

Effect of Polyelectrolyte Mono- and Bilayer Formation on the Colloidal Stability of Layered Double Hydroxide Nanoparticles.

Sequential adsorption of polyelectrolytes on nanoparticles is a popular method to obtain thin films after deposition. However, the effect of polyelectrolyte multilayer formation on the colloidal stability of the nanoparticles has not been studied in detail. In the present work, layered double hydroxides (LDH) were synthesized and interaction with oppositely and like-charged polyelectrolytes was investigated. Electrophoretic and light scattering measurements revealed that colloidal stability of LDH can be tuned by adsorption of poly(styrene sulfonate) (PSS) on the oppositely charged LDH surface in appropriate doses and thus, unstable or stable dispersions can be designed. Negatively charged LDH of adsorbed PSS monolayer was obtained and a poly(diallyldimethyl ammonium chloride) (PDADMAC) second layer was systematically built on the particles. The obtained polyelectrolyte bilayer provided high colloidal stability for the LDH-PSS-PDADMAC dispersions due to the presence of repulsive interparticle forces of electrostatic and steric origin. The results provide crucial quantitative information on designing highly stable particle-polyelectrolyte systems for the preparation of thin films or immobilization of guest substances between the layers for delivery processes.

Configuration-dependent complex formation between Ca(II) and sugar carboxylate ligands in alkaline medium: Comparison of L-gulonate with D-gluconate and D-heptaguconate.

The calcium sugar carboxylate interactions in hyperalkaline solutions are of relevance in radioactive waste repositories and in certain industrial processes. The complex formation between L-gulonate and Ca2+ ions was studied in strongly alkaline medium at 25 °C and 1 M ionic strength and was compared with previous results reported for D-gluconate and D-heptagluconate. The deprotonation of the ligand was confirmed by potentiometric and 13C NMR spectroscopic measurements. Pronounced pH effects were seen in the presence of Ca2+ indicating strong complex formation. By the evaluation of the experimental data, two highly stable trinuclear species, Ca3Gul2H-3+ and the Ca3Gul2H-40, are formed in alkaline aqueous solutions. Polarimetric as well as 1H NMR spectroscopic measurements attested that the increased complex stability was due to the formation of strong metal ion - alcoholate interactions. Moreover, the 1H NMR spectra of the three anions refer to the role of configuration in metal ion-binding. That is, the participation of the C3-OH or C4-OH group is governed by the relative position (i.e., threo or erythro) of the C2-OH and C3-OH groups.