RESUMO
In-based halide perovskites have attracted a lot of attention because of their unique broadband emission properties. Herein, a series of In-based hybrid perovskites of (H2MP)2InCl7·H2O (1), (H2EP)2InCl7·H2O (2), (H2MP)2InBr7·H2O (3), and (H2EP)2InBr7·H2O (4) were synthesized under the control of halogen ions and organic cations. 1, 2, and 4 exhibit obvious photoluminescence properties with peaks at 392, 442, and 652 nm, respectively. The effects of the different components on the crystal structure and photoluminescence properties are discussed by calculating the structural distortion of the [InX6]3- octahedron. The photoluminescence properties of 1 and 4 were significantly improved after Sb3+ doping with PLQY values of 57.12 and 41.53%. Finally, a white LED was successfully fabricated with the two doped compounds coated onto the 365 nm blue LED chip.
RESUMO
Two templated borates, [Co(bpy)2BO2(OH)]·[B5O6(OH)4]·H3BO3·H3O·H2O (1) and [Cu(bpy)(OH)]2·[B5O6(OH)4]2·H2O (2), have been synthesized successfully and characterized by single-crystal X-ray diffraction, powder X-ray diffraction, and Fourier transform infrared. The [Co(bpy)2BO2(OH)] complex in 1 shows a very rare coordination mode between Co2+ and BO2(OH)2-. The structures of 1 and 2 can be adjusted by changing the reagent. The oxygen reduction reaction activity of these Co- and Cu-based catalysts was studied. The E1/2 values of Co-C-750 and Cu-C-750 are 0.864 and 0.837 V, respectively.
RESUMO
Two metal templated borates, [Ni(atta)(SO4)0.5]·[B5O6(OH)4] (1) and [Cu(1-MI)4]·[B5O6(OH)4]2·1-MI2 (2), have been synthesized. The structures were determined by single-crystal X-ray diffraction and further characterized by Fourier transform infrared (FTIR), elemental analysis, and powder X-ray diffraction (PXRD). The structure of 1 consists of [B5O6(OH)4]- clusters and [Ni(atta)(SO4)0.5]+ complexes, which shows a very rare Ni-O-S bond. 1 and 2 exhibit a hydrogen-bonded network formed by [B5O6(OH)4]- clusters. Oxygen reduction reaction (ORR) activities of 1 and 2 were explored.
RESUMO
A zinc acetate borate, [ZnAc]·[ZnBO3] (1), was synthesized under mild conditions; the B@Zn2O3 layer of 1 contains a 6-membered ring embedded with a rare BO3 unit. The layers are pillared by acetate ions to form a 3D framework. The pillared structure of 1 supplies enough space as a nanoreactor, and the related application of CO2-to-CO reduction has been confirmed.
RESUMO
Crystalline materials containing hybrid inorganic-organic metal borates (complexes with oxidoborate ligands) display a variety of novel framework building blocks. The structural aspects of these hybrid metallaoxidoborates containing Cd(II), Co(II), Cu(II), Ga(III), In(III), Mn(II), Ni(II) or Zn(II) metal centers are discussed in this review. The review describes synthetic approaches to these hybrid materials, their physical properties, their spectroscopic properties and their potential applications.
RESUMO
Two hybridized skeleton borates [Zn(en)2]·[B7O12(OH)] (1; en = ethylenediamine) and [Cd(1,3-dap)2]·[B5O8(OH)]·H2O (2; 1,3-dap = 1,3-diaminopropane) were solvothermally synthesized. The boron oxide clusters formed 2D planes, and these planes formed a 3D structure through co-oxygen links of metal complexes. Herein, a novel strategy has been developed, i.e., the derived guest carbon materials from semi-decomposed borate are incorporated into the void of host borate crystals in situ during the thermal etching process. Moreover, the effect of temperature on fluorescence of derived carbon materials was studied. By controlling the calcining temperature, carbon dots with obvious free radicals can be found via ESR technique. Carbon dots in the ethanol phase exhibited variable photoluminescence. Furthermore, it derived semi-decomposition carbon materials via thermal etching based on compounds 1 and 2. In an hydrogen cell reactor, carbon material Zn-based catalyst 1-200 catalyzes CO2 reduction to CO with a selectivity that reaches 50.8% at -1.4 V vs RHE.
RESUMO
The general synthesis and control of the coordination environment of single-atom catalysts (SACs) remains a great challenge. Herein, a general host-guest cooperative protection strategy has been developed to construct SACs by introducing polypyrrole (PPy) into a bimetallic metal-organic framework. As an example, the introduction of Mg2+ in MgNi-MOF-74 extends the distance between adjacent Ni atoms; the PPy guests serve as N source to stabilize the isolated Ni atoms during pyrolysis. As a result, a series of single-atom Ni catalysts (named NiSA -Nx -C) with different N coordination numbers have been fabricated by controlling the pyrolysis temperature. Significantly, the NiSA -N2 -C catalyst, with the lowest N coordination number, achieves high CO Faradaic efficiency (98 %) and turnover frequency (1622â h-1 ), far superior to those of NiSA -N3 -C and NiSA -N4 -C, in electrocatalytic CO2 reduction. Theoretical calculations reveal that the low N coordination number of single-atom Ni sites in NiSA -N2 -C is favorable to the formation of COOH* intermediate and thus accounts for its superior activity.
RESUMO
The first column of two-dimensional (2D)-layered metal-complex-templated nickel borate was obtained by using a solvothermal synthesis method. The 2D nickel borate [Ni(en)3]·[Ni0.5B6O8(OH)4]·Cl (1; en = ethylenediamine) contains [Ni(en)3]2+, Cl-, and the first reported inorganic nickel borate layer [Ni0.5B6O8(OH)4]-, which is formed by the interconnection of Ni and O atoms in the B-O cluster. By increasing the reaction temperature during the synthesis process of compound 1, the one-dimensional (1D) chain nickel borate [Ni(en)3]2·[B7O10(OH)3]·Cl2 (2) was obtained, wherein the [B7O10(OH)3] cluster was connected through an O atom to form a 1D chain structure. By adjusting the molar ratio of the raw materials, that is, adjusting the pH of the reaction, the other 1D chain nickel borate Ni(en)3·Hen·[B9O13(OH)4]·H2O (3) was obtained, in which [B5O8(OH)2] and [B4O7(OH)2] clusters can be connected via a common O atom to form an infinite [B9O13(OH)4] polyanionic chain. Meanwhile, we successfully synthesized the isoform of compound 3 with the metal cadmium.
RESUMO
We herein report the first example of Li+ exchanged with both the guest H2N(Me)2+ cations located in the channels and the coordinated metal ions from an anionic metal-organic framework (MOF), leading to significant enhancement of the pore volume and gas sorption abilities of the exchanged MOF. Furthermore, both MOFs before and after Li+ exchange show good selective adsorption for CO2 over CH4.
RESUMO
Ni(en)3·Hen·[B9O13(OH)4]·H2O was prepared under the cotemplating effect of [Ni(en)3](2+) and Hen(+). It was the first example of a cotemplated borate with an unusual chiral polyanionic chain, which was constructed from [B5O8(OH)2] and [B4O7(OH)2] clusters.
RESUMO
Halide perovskites have high photoelectric conversion efficiency, making them promising candidates for photocatalysis. However, their toxic and unstable nature limits their applications. Here, we successfully synthesised three hybrid Bi-based halide perovskites: (HTMG)3Bi2Br9 (1), (HEI)2BiBr5 (2) and (HTMA)3Bi2Br9 (3). X-ray single-crystal diffraction analysis shows that they all contained 0D structures composed of isolated Bi-Br clusters. The three compounds showed excellent degradability and cycling stability for Sudan III dissolved in ethanol under simulated sunlight. In addition, the photocatalytic degradation performance of four Bi-based halide perovskites previously reported by our group is also characterised and summarised in this work.
RESUMO
Two templated borates, [Co(1-EI)2]·[B5O7(OH)3] (1) and [Ga(1-MI)2·B6O9(OH)4]·[H3BO3]·H[1-MI] (2), have been synthesized using a mild method. Notably, they exhibit an excellent ORR performance with an E1/2 value of 0.84 V and are the first to be used as the positive electrode catalyst for a zinc-air battery, which opens a pathway for the application of borate-based oxide catalysts.
RESUMO
A series of mono/bimetallic isostructural hybrid tetraborates of the general formula [ZnxCo(1-x)(1,3-dap)B4O7] has been prepared using a solvothermal method. Their adsorption/desorption curves for H2O and D2O demonstrate that these materials have a stronger affinity for H2O than for D2O and enrich the D2O content of D2O/H2O mixtures.
RESUMO
Four new transition metal borates, [Co(1-MI)2]·B5O7(OH)3 (1, 1-MI = 1-methylimidazole), Co2(PZ)8(SO4)2·2H3BO3 (2, PZ = pyrazole), K7{(BO3)Co[B12O18(OH)6]}·H2O (3) and K2{[Ni(PY)2]2·[(C4H2O6)2B]}2 (4, PY = pyridine), have been successfully synthesized by a mild method. Their structures were determined by X-ray single crystal diffraction. These compounds were further characterized by FTIR, PXRD and UV-vis-NIR. It is worth noting that the catalytic properties of catalysts based on these four borates were explored, and that organically templated borate 1- and 2-based catalysts showed better ORR catalytic performance compared to 3- and 4-based catalysts. This may be caused by the supramolecular skeletons of 1 and 2 providing sufficient space and porosity.
RESUMO
WNK4 (with no lysine kinase 4) inhibits ROMK channel activity in the distal nephron by stimulating clathrin-dependent endocytosis, an effect attenuated by SGK1 (serum-glucocorticoids-induced kinase)-mediated phosphorylation. It has been suggested that increased ROMK activity because of SGK1-mediated inhibition of WNK4 plays a role in promoting renal K secretion in response to elevated serum K or high K (HK) intake. In contrast, intravascular volume depletion also increases SGK1 activity but fails to stimulate ROMK channels and K secretion. Because HK intake decreases Src family protein tyrosine kinase (PTK) activity an inhibitor of ROMK channels, it is possible that Src family PTK may modulate the effects of SGK1 on WNK4. Here, we show that c-Src prevents SGK1 from attenuating WNK4's inhibition of ROMK activity. This effect of c-Src was WNK4-dependent because c-Src had no effect on ROMK harboring mutation at the site of c-Src phosphorylation (R1Y337A) in the absence of WNK4. Moreover, expression c-Src diminished the SGK1-mediated increase in serine phosphorylation of WNK4, suggesting that c-Src enhances WNK4-mediated inhibition of ROMK channels by suppressing the SGK1-induced phosphorylation. This notion is also supported by the observation that c-Src was not able to modulate the interaction between SGK1 and WNK4 mutants (WNK4(S1169A) or WNK4(S1169D)) in which an SGK1-phosphorylation site (serine 1169) was mutated by alanine or aspartate. We conclude that c-Src inhibits SGK1-mediated phosphorylation hereby restoring the WNK4-mediated inhibition of ROMK channels thus suppressing K secretion.
Assuntos
Proteínas Imediatamente Precoces/metabolismo , Canais de Potássio Corretores do Fluxo de Internalização/metabolismo , Proteínas Serina-Treonina Quinases/metabolismo , Quinases da Família src/metabolismo , Linhagem Celular , Fenômenos Eletrofisiológicos , Humanos , Técnicas de Patch-Clamp , Fosfosserina/metabolismo , Canais de Potássio Corretores do Fluxo de Internalização/genética , Ligação Proteica , Proteínas Serina-Treonina Quinases/genéticaRESUMO
Three nickel borate compounds, [Ni(1-MI)6]·[B(OH)3]4·SO4 (1-MI = 1-methylimidazole) (1), [Ni(H2O)3(1-MI)3]·[B5O6(OH)4]2 (2) and [Ni(DMA3)]·[B6O7(OH)6]·3.5H2O (DMA3 = N,N-dimethylethylenediamine) (3), have been synthesized. It is noteworthy that the structures of 1 and 2 can be adjusted by varying the ratio of amine. Compound 3 has shown an unexpected example of unique water clusters in its structure. The three frameworks exhibit different interlinkage modes, resulting in channels varying in their size and shape. These compounds have been characterized by FTIR, UV-vis and PXRD. In addition, 1, 2, and 3 exhibited different wide band gaps (4.4 eV for 1, 4.5 eV for 2 and 4.4 eV for 3), and ORR activities with a half-wave potential of 0.78 V for 1, 0.74 V for 2 and 0.79 V for 3.
RESUMO
Mn:CsPbBr3 PQDs are achieved by hot injection method. As the amount of Mn doping is gradually increased, the photoluminescence (PL) spectra shows a slight blue shift. Mn-doped PQDs exhibit higher quantum efficiency of 83.9% and longer lifetimes of 267 ns. The stability test was performed to assess the susceptibility of the PQDs to polar solutions. It was figured out that although the stabilities of CsPbBr3 PQDs and Mn-doped PQDs decreased as the polarity of solution increased, Mn-doped PQDs still maintained higher PL intensity than undoped PQD. Notably, 73% PL intensity of Mn:PQDs was maintained which is nearly three times as much as undoped PQDs in water. We found polarity would induce drastic degradation of CsPbBr3 QDs. The steady-state spectroscopy, transmission electron microscopy (TEM), and X-ray diffraction (XRD) verified that CsPbBr3 QDs tend to aggregate to form larger particles under continuous light soaking. Our work reveals the main origin of instability in CsPbBr3 QDs and provides reference to engineering such QDs towards optimal device application.
RESUMO
In this work, different synthetic methods were used to prepare metal borates. One cadmium borate Cd3[B6O9(OH)2]2·2NO3·4H2O (1) and two nickel borate Ni0.8Mn0.2{B6O7(OH)3[O(CH2)2NH2]3} (2), [Ni(1-MI)6]·[B5O6(OH)4]2·2DMF (3, 1-MI = 1-methylimidazole, DMF = N,N-dimethylformamide) species were successfully prepared. The structures of these three compounds were confirmed via single crystal powder X-ray diffraction (SCPXRD), elemental analysis, FTIR, PXRD, and ICP studies. Compound 1 was prepared via molten salt synthesis, and compounds 2 and 3 were prepared via precursor synthesis, which is a synthetic method that uses a certain polyanionic cluster as a reagent. Compound 1 shows a novel three-dimensional (3D) structure, in which the [B6O11(OH)2] units acting as the basic polyanionic cluster form a two-dimensional (2D) anionic structure. In addition, the unexpected Cd3O14 clusters are connected with the 2D structures, leading to the 3D structure. The crystal structure of 2 is packed with very large neutral Ni0.8Mn0.2{B6O7(OH)3[O(CH2)2NH2]3} oxo-metal-boron clusters. The crystal structure of 3 consists of a [B5O6(OH)4]- cluster, a DMF molecule, and a [Ni(1-MI)6]2+ complex. In particular, 2 was successfully constructed using the same hexaborate cluster as its precursor. However, 3 only contains Ni2+ cations when a neutral NixMn1-x[B6O7(OH)6] cluster was used as an initial reagent, and it shows an ability to select a certain metal cation during the self-assembly process. Moreover, compounds 1, 2, and 3 exhibit different wide band gaps of 3.06 eV (1), 3.95 eV (2), and 4.24 eV (3).
RESUMO
Five aluminoborates Al[B(5)O(10)] x H(2)dab x 2 H(2)O (1), [Al(B(4)O(9))(BO)] x H(2)en (2), [Al(B(4)O(9))(BO)] x H(2)dap (3), K(2)Al[B(5)O(10)] x 4 H(2)O (4), and (NH(4))(2)Al[B(5)O(10)] x 4 H(2)O (5) have been synthesized under hydrothermal conditions and characterized by means of elemental analysis, IR, TG analysis, MAS NMR, UV-vis and fluorescence spectroscopy, powder X-ray diffraction, single-crystal X-ray diffraction, and NLO determination. The structure 1 comprises of AlO(4) tetrahedra and B(5)O(10) clusters and contains 12-, 11-, and 8-MR 3D-intersecting channels with a CrB(4) topological net. Structures 2 and 3 are both constructed from the same AlB(5)O(13) clusters and exhibit a six-connected framework with 4(12)6(3) topology. Structures 4 and 5 are isomorphous and are composed of AlO(4) tetrahedra and B(5)O(10) clusters that possess odd 11-MR channels and 8-MR helical channels. Structures 2-5 crystallized in an acentric structure and presented good SHG properties. UV-vis spectral investigation indicates that they are wide-band-gap semiconductors. The electronic structure calculations for the compounds also have been performed.
Assuntos
Compostos de Alumínio/química , Compostos de Alumínio/síntese química , Boratos/química , Boratos/síntese química , Simulação por Computador , Cristalografia por Raios X , Espectroscopia de Ressonância Magnética , Modelos Químicos , Modelos Moleculares , Espectrometria de Fluorescência , Espectrofotometria Ultravioleta , TemperaturaRESUMO
White-light-emitting Ag, Mn: Zn-Ga-S/ZnS quantum dots (QDs) with a gratifying photoluminescence (PL) quantum yield (QY) of up to 90% were prepared, and shown to be ultra-stable, maintaining a high PL intensity at 300 °C or for 32 h of UV illumination. These QDs were employed in a white QD-LED displaying a color rendering index (CRI) of 72 and maximum current efficiency of 0.22 cd A-1.